Similar Questions

• RADIUS-server host command problem

  Hi all

  I have cisco 4506 e - 8 L - e sup with the latest IOS image, but host X.X.X.X command radius server is not available, I've heard that this order has been changed now, can someone tell me the new syntax of this command because I'm setting this switch to cisco ISE...

  Kind regards

  The syntax is:

  radius server A-NAME-FOR-THE-SERVER address ipv4 10.10.10.10 auth-port 1812 acct-port 1813 key YOUR-KEY

• WiFi WPA2 Enterprise with RADIUS - connection problem

  Hello

  I have here a new ISA 570w with the latest firmware (1.2.17).

  Anyway, I can't get wifi to work in mode WPA2 Enterprise with RADIUS authentication.

  Mode WPA2 PSK are not a problem.

  I have configured the BEAM properly and I can connect directly to him via NTRadPing without any problem. Also the test in the web interface works without any problem (see Figure 2, 3).

  The RADIUS server is a server Synology RADIUS on a Synology NAS, which is a FreeRADIUS server under the hood.

  In the settings of the ISA wireless, I put this RADIUS server for authentication (see screenshot 1, 4).

  However, I can not connect to connect to the network:

  On the iPhone (iOS 6.1.3) I get a prompt for a user name and password, but when I click on connect, it says 'connect to 'cisco3'... ". "and stays there.

  In ISA 570w newspaper, he said:

  Information

  Wireless

  MSG = add MAC station in the list of the ATU. VID = 5; MAC = 5 C: 59:48:02:78:3E;

  Information

  Wireless

  MSG = Wireless mode is a 802.11 mixed b_g_n

  When I cancel the connection attempt, he said:

  Information

  Wireless

  MSG = the Client has dissociated;

  On my Thinkpad with Windows 7 Professional I have everything configured as usual (see screenshots 5,6,7,8) but when I try to connect I do not get a command prompt where I wonder username and password, and finally the connection cannot be established (see Figure 9). Also tried with the same configuration on an another Windows 7 Pro installed costs for laptop with the same problem.

  I can't see any attempt of 570w ISA to authenticate anything in the logs of the RADIUS.

  Also the capture of network traffic on the LAN to the Synology NAS port does not show the RADIUS datagrams.

  I already disabled COP because I read that it can cause problems, but it did not help.

  Can you please suggest something else I can try?

  Thanks in advance!

  Kind regards

  Dominik

  I saw these screenshots, but that screen settings just select the button set up next to the authentication method in the section user authentication, under users.  In each of your screenshots, the RADIUS server identification number is 1, so I would also ensure that I configured the server ID RADIUS 1 that can be configured by going to users-> RADIUS servers.

  All that said, I have seen that your tests have passed and I also do not understand the point of having the RADIUS settings on other screens and then to have info ID RADIUS.  My thought is that you'd be able to pre-set RADIUS users of-> screen RADIUS servers and then select the RADIUS server ID in all other screens without having to enter the RADIUS news over and over again.  He also thinks that you could ignore the users-> screen RADIUS server and enter RADIUS information over and over again and it should work... as you set up initially.  However, based on the past experience of programming errors, I recommend configuring the ID from RADIUS server 1 under user-> RADIUS servers if you have not already... just in case where.

  Shawn Eftink
  CCNA/CCDA

  Please note all useful messages and mark the correct answers to help others looking for solutions in the community.

• switch 3750 EAPoL transmission RADIUS server

  I have a running version of the 3750 switch stack 12.2 (53) SE2 IPBASEK9-M. I have dot1x configured on the switch and a Windows 7 PC, connected with 802. 1 x configured on the interface. I see the EAPoL start message from the PC, but I do not see the packets from the switch to the RADIUS server RADIUS. I have a config simple dot1x just to try to make it work before adding additional features such as comments - vlan...

  Config and debug of attached file.

  I don't know if the configuration ip dhcp snooping and arp of inspection is cause a problem with that or not. I see the EAPoL packet received on the switch, as shown in the attachment of debugging, but I never see the RADIUS packet. I've defined both trust on the interface, but always the same result. I can't turn it off because there is a switch of production with a test interface.

  Any ideas?

  Thank you

  Mark

  I had the same problem and solved it is enough to configure the switch as authenticator instead of "supplicant". "Supplicant" means customer, "authenticator" means in fact the switch acts as an authenticator to pass through, it will forward the requests to the auth server, for example, host of RADIUS.

• Cisco 1812 no contact to the Radius Server

  Hi guys,.

  IM pretty new to cisco and plays with an 1812 products... I am trying set up an easy VPN server, with the support of ray and I can see that I did everything right, but there is a problem, because the router do not contact the RADIUS server and the RADIUS server has been tested ok.

  Anyone who can see what I'm missing? Worked with this problem for 3 days now.

  Here is my CONF.

  Current configuration: 9170 bytes

  !

  ! Last modification of the configuration to 13:44:49 UTC Tuesday, October 12, 2010

  !

  version 15.1

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  router host name

  !

  boot-start-marker

  boot-end-marker

  !

  !

  no set record in buffered memory

  !

  AAA new-model

  !

  !

  AAA server radius sdm-vpn-server-group 1 group

  auth-port 1645 90.0.0.245 Server acct-port 1646

  !

  AAA authentication login default local

  AAA authentication login sdm_vpn_xauth_ml_1-passwd-expiry group sdm-vpn-server-group 1

  AAA authorization exec default local

  AAA authorization sdm_vpn_group_ml_1 LAN

  !

  !

  !

  !

  !

  AAA - the id of the joint session

  !

  Crypto pki token removal timeout default 0

  !

  Crypto pki trustpoint TP-self-signed-250973313

  enrollment selfsigned

  name of the object cn = IOS - Self - signed - certificate - 250973313

  revocation checking no

  !

  !

  TP-self-signed-250973313 crypto pki certificate chain

  certificate self-signed 01

  308201A 5 A0030201 02020101 3082023C 300 D 0609 2A 864886 F70D0101 04050030

  2 040355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30

  69666963 32353039 37333331 33301E17 313031 30313230 39343333 0D 6174652D

  395A170D 2E302C06 1325494F 03540403 32303031 30313030 30303030 5A 303031

  532D 5365 6C662D53 69676E65 4365 72746966 69636174 652 3235 30393733 642D

  06092A 86 4886F70D 01010105 33313330 819F300D 00308189 02818100 0003818D

  BCF94FB0 77240E92 B703CE70 556D5D22 A57823E5 DD4CD4C4 12D639DE 5E97DB2D

  81FBB304 9FA677A6 CAD84F96 9734081B F8F8FAAE 000B02FB AEF7C7B1 73AFA44B

  7D27E112 8991F03B 3D4FD484 34E2EA9F BD426F73 48778F2A AD35AAD6 EC00805D

  249B 8702 D545AEEA 40670DFD 3E6BEC29 EE48A0C6 CB7694FD 722D1A62 3A499CC5

  02030100 01A 36630 03551 D 13 64300F06 0101FF04 05300301 01FF3011 0603551D

  11040A 30 08820652 6F757465 72301F06 23 04183016 801462CB F6BD12F6 03551D

  080C8A89 F9FBBDCE 9751528A FFFD301D 0603551D 0E041604 1462CBF6 BD12F608

  0C8A89F9 FBBDCE97 51528AFF FD300D06 092 HAS 8648 01040500 03818100 86F70D01

  ACA87977 CF 55225 6 9147E57E 8B5A8CA8 46348CAF 801D11C6 9DA57C69 14FA5076

  6844F0CC 4CBEB541 136A483A 69F7B7F0 E44474E8 14DC2E80 CC04F840 B 3531, 884

  F08A492D 8C3902C0 725EE93D AC83A29F 799AAE0F 5795484B B3D02F84 911DB135

  5 189766 C30DA111 6B9B4E46 E999DA5B 202 21B0B9D4 HAS 6900 07A93D8D 41C7FD21

  quit smoking

  dot11 syslog

  IP source-route

  !

  !

  !

  !

  !

  IP cef

  No ipv6 cef

  !

  Authenticated MultiLink bundle-name Panel

  !

  !

  !

  license udi pid CISCO1812/K9 sn FCZ10232108

  username admin privilege 15 secret 5 P677 $1$ $ Rggfdgt8MeD8letZDL08d.

  !

  !

  !

  type of class-card inspect correspondence sdm-nat-smtp-1

  game group-access 101

  smtp Protocol game

  type of class-card inspect entire game SDM_AH

  match the name of group-access SDM_AH

  type of class-card inspect all sdm-cls-insp-traffic game

  match Protocol cuseeme

  dns protocol game

  ftp protocol game

  h323 Protocol game

  https protocol game

  match icmp Protocol

  match the imap Protocol

  pop3 Protocol game

  netshow Protocol game

  Protocol shell game

  match Protocol realmedia

  match rtsp Protocol

  smtp Protocol game

  sql-net Protocol game

  streamworks Protocol game

  tftp Protocol game

  vdolive Protocol game

  tcp protocol match

  udp Protocol game

  inspect the class-map match sdm-insp-traffic type

  corresponds to the class-map sdm-cls-insp-traffic

  type of class-card inspect all SDM-voice-enabled game

  h323 Protocol game

  Skinny Protocol game

  sip protocol game

  type of class-card inspect entire game SDM_IP

  match the name of group-access SDM_IP

  type of class-card inspect entire game SDM_ESP

  match the name of group-access SDM_ESP

  type of class-card inspect entire game SDM_EASY_VPN_SERVER_TRAFFIC

  match Protocol isakmp

  match Protocol ipsec-msft

  corresponds to the SDM_AH class-map

  corresponds to the SDM_ESP class-map

  type of class-card inspect the correspondence SDM_EASY_VPN_SERVER_PT

  corresponds to the SDM_EASY_VPN_SERVER_TRAFFIC class-map

  type of class-card inspect all match sdm-cls-icmp-access

  match icmp Protocol

  tcp protocol match

  udp Protocol game

  type of class-card inspect correspondence sdm-invalid-src

  game group-access 100

  type of class-card inspect correspondence sdm-icmp-access

  corresponds to the class-map sdm-cls-icmp-access

  type of class-card inspect correspondence sdm-Protocol-http

  http protocol game

  !

  !

  type of policy-card inspect sdm-permits-icmpreply

  class type inspect sdm-icmp-access

  inspect

  class class by default

  Pass

  type of policy-card inspect sdm-pol-NATOutsideToInside-1

  class type inspect sdm-nat-smtp-1

  inspect

  class class by default

  drop

  type of policy-map inspect sdm - inspect

  class type inspect sdm-invalid-src

  Drop newspaper

  class type inspect sdm-insp-traffic

  inspect

  class type inspect sdm-Protocol-http

  inspect

  class type inspect SDM-voice-enabled

  inspect

  class class by default

  Pass

  type of policy-card inspect sdm-enabled

  class type inspect SDM_EASY_VPN_SERVER_PT

  Pass

  class class by default

  drop

  type of policy-card inspect sdm-license-ip

  class type inspect SDM_IP

  Pass

  class class by default

  Drop newspaper

  !

  security of the area outside the area

  safety zone-to-zone

  ezvpn-safe area of zone

  safety zone-pair sdm-zp-self-out source destination outside zone auto

  type of service-strategy inspect sdm-permits-icmpreply

  source of sdm-zp-out-auto security area outside zone destination auto pair

  type of service-strategy inspect sdm-enabled

  safety zone-pair sdm-zp-in-out source in the area of destination outside the area

  type of service-strategy inspect sdm - inspect

  sdm-zp-NATOutsideToInside-1 zone-pair security source outside the area of destination in the area

  type of service-strategy inspect sdm-pol-NATOutsideToInside-1

  in the destination box source sdm-zp-in-ezvpn1 ezvpn-pairs area security

  type of service-strategy inspect sdm-license-ip

  source of sdm-zp-out-ezpn1 of security area outside zone ezvpn-zone time pair of destination

  type of service-strategy inspect sdm-license-ip

  safety zone-pair sdm-zp-ezvpn-out1-source ezvpn-zone of destination outside the area

  type of service-strategy inspect sdm-license-ip

  safety zone-pair source sdm-zp-ezvpn-in1 ezvpn-area destination in the area

  type of service-strategy inspect sdm-license-ip

  !

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group Sindby crypto isakmp client

  key TheSommerOf03

  90.0.0.240 DNS 8.8.8.8

  win 90.0.0.240

  SBYNET field

  pool SDM_POOL_2

  Max-users 15

  netmask 255.255.255.0

  ISAKMP crypto sdm-ike-profile-1 profile

  identity Sindby group match

  client authentication list sdm_vpn_xauth_ml_1

  ISAKMP authorization list sdm_vpn_group_ml_1

  client configuration address respond

  virtual-model 1

  !

  !

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac

  Crypto ipsec transform-set esp-SHA2-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA3-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA4-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA5-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA6-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA7-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA8-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA9-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA10-ESP-3DES esp-sha-hmac

  !

  Profile of crypto ipsec SDM_Profile1

  game of transformation-ESP-3DES-SHA10

  isakmp-profile sdm-ike-profile-1 game

  !

  !

  !

  !

  !

  !

  interface BRI0

  no ip address

  encapsulation hdlc

  Shutdown

  !

  interface FastEthernet0

  Description $FW_OUTSIDE$

  IP address 93.166.xxx.xxx 255.255.255.248

  NAT outside IP

  IP virtual-reassembly in

  outside the area of security of Member's area

  automatic duplex

  automatic speed

  !

  interface FastEthernet1

  no ip address

  Shutdown

  automatic duplex

  automatic speed

  !

  interface FastEthernet2

  !

  interface FastEthernet3

  !

  interface FastEthernet4

  !

  interface FastEthernet5

  !

  FastEthernet6 interface

  !

  interface FastEthernet7

  !

  interface FastEthernet8

  !

  interface FastEthernet9

  !

  type of interface virtual-Template1 tunnel

  IP unnumbered FastEthernet0

  ezvpn-safe area of Member's area

  ipv4 ipsec tunnel mode

  Tunnel SDM_Profile1 ipsec protection profile

  !

  interface Vlan1

  Description $FW_INSIDE$

  IP 90.0.0.190 255.255.255.0

  IP nat inside

  IP virtual-reassembly in

  Security members in the box area

  !

  local IP SDM_POOL_1 90.0.0.25 pool 90.0.0.29

  local IP SDM_POOL_2 90.0.0.75 pool 90.0.0.90

  IP forward-Protocol ND

  IP http server

  local IP http authentication

  IP http secure server

  IP http timeout policy inactive 600 life 86400 request 10000

  !

  !

  IP nat inside source static tcp 192.168.1.200 25 interface FastEthernet0 25

  the IP nat inside source 1 interface FastEthernet0 overload list

  IP route 0.0.0.0 0.0.0.0 93.166.xxx.xxx

  !

  SDM_AH extended IP access list

  Remark SDM_ACL = 1 category

  allow a whole ahp

  SDM_ESP extended IP access list

  Remark SDM_ACL = 1 category

  allow an esp

  SDM_IP extended IP access list

  Remark SDM_ACL = 1 category

  allow an ip

  !

  exploitation forest esm config

  access-list 1 permit 90.0.0.0 0.0.0.255

  Access-list 100 = 128 SDM_ACL category note

  access-list 100 permit ip 255.255.255.255 host everything

  access-list 100 permit ip 127.0.0.0 0.255.255.255 everything

  access-list 100 permit ip 93.166.xxx.xxx 0.0.0.7 everything

  Remark SDM_ACL category of access list 101 = 0

  IP access-list 101 permit any host 192.168.1.200

  !

  !

  !

  !

  !

  !

  RADIUS-server host 90.0.0.245 auth-port 1645 acct-port 1646

  !

  control plan

  !

  !

  Line con 0

  line to 0

  line vty 0 4

  transport input telnet ssh

  !

  end

  Hello

  Looks like you're missing the key from the radius server configuration "RADIUS-server host 90.0.0.245 auth-port 1645 1646 key your_keyacct-port»

  Thank you

  Wen

• In Active/Passive Mode Radius server configuration

  We set up (active/active) the two ASA load balancing.  We also configure two Radius servers with load balancing.  At present, the Radius servers are configured with active/active.  Is it possible to configure a Radius Server with (active/passive)?

  RADIUS protocol Radius AAA server
  AAA-server Radius (inside) host XXX.XXX.XXX.XXX
  Timeout 300
  key *.
  RADIUS-common-pw *.

  AAA-server Radius (inside) host XXX.XXX.XXX.XXX
  Timeout 300
  key *.
  RADIUS-common-pw *.

  AAA accounting enable console RADIUS

  Thank you.

  Diane

  Diane,

  Well I'm still not 100% sure that you understand exactly what is happening. Normally, on a single ASA, authentication is always performed on the same radius server until it fails (i.e. active/passive as you call it).

  Now, you mention that you have 2 ASAs in load balancing, so I don't know if you mean that:

  (1) 2 users that connect to the same ASA get authenticated by radius 2 servers different (should never happen)

  or

  (2) when 2 users connect to the cluster, user1 gets redirected to ASA1 and authenticated on Radius1, while User2 will be redirected to ASA2 using Radius2 to auth. This could be normal if both ASAs are set up differently (defined in a different order radius servers) or an ASA had a problem connecting to Radius1, at some point and so it considered out of service.

  In any case, 'sh aaa-server protocol radius' and 'debug RADIUS' can help determine why an asa individual does not use (initially configured) primary radius server.

  HTH

  Herbert

• RADIUS server with no devices of the airport

  Is there a way I can set up a radius server by using the OS X application but not a Terminal airport at el capitan? Thank you

  See if that helps.

  Mavericks of OS X Server - setting up FreeRADIUS

• changed Kapersky security with mcafee and cannot retrieve e-mail messages. problems of server on the computer. McAfee can enter my password and my email. they say that I have a server problem.

  changed to mcafee kapersky and cannot receive my e-mail address. McAfee can use my username and password and receive my email. they say that I have a server problem.

  Hello

  I suspect that the problem is with your e-mail service provider, therefore, suggest you to contact your provider of messaging for better help.

• Outlook Express 6: your server has unexpectedly ended the connection. The potential causes for this include server problems, network problems, or a long period of inactivity. Error number: 0x800ccc0f

  Original title: Windows XP and Outlook Express 6

  I have a new computer with outlook express and went through the set up instructions.  When I tried to send a test email, I got this error message:

  "Your server has terminated suddenly the connection. The possible causes for this include server problems, network problems, or a long period of inactivity. Account: 'pop.mail.yahoo.com', server: 'pop.mail.yahoo.com', Protocol: POP3, Port: 110, secure (SSL): Yes, error number: 0x800CCC0F. »

  How can I fix this error message and have e-mail sent via Outlook?

  Hi Jeanette Logan,
   
  Here is an article that addresses this issue. Follow the steps listed in the article for this problem:
   
  Troubleshooting error messages that you receive when you try to send and receive e-mail in Outlook and Outlook Express

• Your server suddenly put an end to the connection. The possible causes for this include server problems, network problems, or a long period of inactivity.

  Your server suddenly put an end to the connection. The possible causes for this include server problems, network problems, or a long period of inactivity. Topic "business profile]', account:"pop.bizmail.yahoo.com", server:"smtp.bizmail.yahoo.com"', Protocol: SMTP, server response: ' 451 see http://pobox.com/~djb/docs/smtplf.html. ', Port: 25, secure (SSL): no, Server error: 451, error number: 0x800CCC0F"

  Your server suddenly put an end to the connection. The possible causes for this include server problems, network problems, or a long period of inactivity. Topic "business profile]', account:"pop.bizmail.yahoo.com", server:"smtp.bizmail.yahoo.com"', Protocol: SMTP, server response: ' 451 see http://pobox.com/~djb/docs/smtplf.html. ', Port: 25, secure (SSL): no, Server error: 451, error number: 0x800CCC0F"

  You must make a few changes, not only on outgoing parameters, your incoming parameters also need changes.

  Open your e-mail program > tools > accounts > your bizmail account > properties > servers, under outgoing mail server, check "this server requires authentication" > apply > advanced, under outgoing (SMTP) mail change to 465 not 25. Put a check mark on "this server requires a secure connection (SSL)" > under incoming (POP3) mail, change it to 995 no 110. Put a check mark on "this server requires a secure connection (SSL)" > OK

  t-4-2

• launch of checkers problems: error: trying to re-launch your game. If the problem persists, it may be network with the server problems or a problem with the configuration of your firewall.

  Windows Vista can not launch problem of checkers: try to re-launch your game. If the problem persists, it may be network with the server problems or a problem with the configuration of your firewall. Please check your firewall settings by visiting the Open Ports FAQ.

  Original title: launch of the problems of checkers:

  Hello

  If you have not yet tried to disable the antivirus/firewall software, then try the following steps to disable them.

  Disable the anti-virus software: http://windows.microsoft.com/en-US/windows-vista/Disable-antivirus-software

  Enable or disable Windows Firewall: http://windows.microsoft.com/en-US/windows-vista/Turn-Windows-Firewall-on-or-off

  IMPORTANT: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks

• Try to create the new account. Message: Server problems! Since 2 days. Who can help?

  Bought the new printer (Photosmart C410b) HP with ePrint option.

  Try to create a new account in eprintcenter.com to save my printer

  to use ePrint. Get a similar message for 2 days:

  "Sorry, we have server problems. We noticed the problem and will come up with a solution.

  I use the German Web site. Is there really a problem since 2 days or is there a any error on my part?

  Who can help?

  Paschahelen

  Problem solved! Found the solution by checking German blogs with the same question.

  System doesn´t accept "Umlaute" (Aug), which are common in European languages.

• Dell Powerconnect 35xx series features Radius Server behaviorfin

  Hello Dell Community,

  I'm not able to find out how 35xx series switches handle 'server radius deadtime' parameter as described below:

  In the config of switch, I use two hosts(for redundancy) radius. The first has priority of '1' configured RADIUS, the second server is priority '2 '. So normally, if the first sever(priority 1) RADIUS online, auth requests switch are sent to this server all the time. And they really are.

  Now, I have also configured the 'deadtimet 10 radius server', meaning to jump on the radius server does not respond. Does that mean exactly?

  If the radius with priority 1 server is offline for a few seconds, the switch instantly consider this as dead radius server and sent no auth request it for the "period deadtime ' 10 minutes (depending on configuration)? How often switch check for the availability of the radius server host?

  config swtich:

  IP address Port port Prio time - Ret-dead-source IP. Its use
  AUTH Acct Out rans times
  --------------- ----- ----- ------ ------ ------ --------------- ----- -----
  10.10.10.10 1812 1813 global Global Global Global 1 all the
  10.10.10.20 1812 1813 global Global Global Global every 2

  Global values
  --------------

  Waiting period: 2
  Broadcast: 5
  Deadtime: 10
  Source IP: 0.0.0.0
  Source IPv6:

  Retransmission will say the switch many times in an attempt to authenticate to the RADIUS server before moving on to the second server. Timeout is indicative of the switch, the waiting time for a response. Deadtime will subsequently intervene in these two parameters have been exhausted.

  Example config:

  Server radius coverage of console (config) # 3

  Console (config) # timeout 3 radius server

  Deadtimet console (config) # 10 radius server

  Result of config:

  -The client tries to connect.

  -switch attempts to authenticate the server 1.

  -Switch means no RADIUS server 1 for 3 second.

  -Switch waits 3 seconds.

  -Switch attempts to authenticate to the RADIUS server 1 for the second time and does not return to server for 3 seconds.

  -Switch waits 3 seconds.

  -Switch attempts to authenticate to the RADIUS server 1 for the third time and does not return to server for 3 seconds.

  -switch place RADIUS server, one in a State of low/dead for 10 minutes.

  -switch attempts to authenticate to Server 2.

• RADIUS Server - Windows server 2008

  Hello world

  We use the windows 2008 standard server to our domain controller. We have been in for the last two years radius server in our campus. I could see that we can configure the client only 50 radius in NPS. Is it possible to add a plus in windows 2008 standard?

  Please help me

  Teckzx

  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Server problems

  Hello everyone,

  I have problems connecting to the server. I recently downloaded Microsoft Office 365, and I have the product installed on my computer. However, when I click on the ""Sign in"button in the upper right corner of Microsoft Word (Excel, Powerpoint) it sends a message saying"Sorry, we have temporary server problems."" At first I thought the problem was just of Microsoft Office, but now, I've seen other products I was installing have said similar things such as "cannot connect to Server", "is there a problem with your connection", or 'server '.

  I have wifi and there are always 4-5 bars in the lower right corner, and I am able to use the internet browser (I use it as I type this). The first thing I looked at was the server information. Most of the information went over my head, because I am a novice at this stuff, but the essential, that they mentioned was to connect the clock of the internet via the control panel. I did and I still have these server problems. Another thing to check, I saw was the bing via the command prompt. I tried and it said 0% loss (4 envoys and 4 received) and server problems have continued.

  I have a Windows 7 Inspiron 537 s, and my internet is provided by AT & T.

  This office has been mainly sitting back where it has not been used much (my brother and I used sporadically). I decided to move instead of easier access, because it's a good computer.

  The main culprit, I can think of is the wireless network adapter I bought, so this computer is Wi-Fi (instead of an Ethernet cable on the floor), but like I said that the computer has a strong wifi connection. The adapter is a Netgear AC1200.

  No other devices on my network are facing this problem, it's just this office.

  So, just a little recap

  1. I have a wifi connection, and I am able to use internet browsers and download files.
  2. I can't connect to the "servers", such as Microsoft Office.

  Any help would be appreciated, because I can't seem to find someone with a similar problem on the internet.

  This is a link to where I posted this question in the Forum Office (Accident, I didn't see it), where a person tried to help me and there is a little more information. Aid has led to post me here, and the guest in this thread is the same as exact as this thread.

  http://answers.Microsoft.com/en-us/Office/Forum/office_365hp-office_install/server-problems/e8fdace1-4CEC-4B36-95a8-8508dc90af45

  Hello

  Thanks for posting your query on Microsoft Community forum.

  According to the description of the problem, it seems that there could be a chance of third-party applications, services or security software are limiting to connect.

  So I would you suggest temporarily disabling security software and perform the clean boot and then try to sign in to Office 365 and see if it helps.

  Step 1

  Try temporarily disabling security software and then see if it helps.

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attack.

  Step 2

  Perform a clean boot.

  Put your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135/en-us

  Note: See "how to reset the computer to start normally after a boot minimum troubleshooting" to prepare the computer to start as usual after a repair.

  In addition to that I suggest you to check the system files are they work very well or not and to check who are trying to run the (SFC) System File Checker tool.

  Scan SFC will be scans all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  1. Go to Start, click all programs and open the Accessories.
  2. Right-click on command prompt in the list programs, and then select run as administrator. If you are prompted for an administrator password or for confirmation, type your password, or click OK.
  3. In the command prompt, type the following command and press ENTER:

  sfc/scannow

  For more information, refer to this link:

  http://support.Microsoft.com/kb/929833/en-us

  Hope it would help. If the problem still persists, post back with the current state of your computer and the result of the suggestions, we will be happy to help you.

  Kind regards