Configuration software re - assign the strength

Similar Questions

• Need help with the disks 'unreadable' configuring software raid after the death of the startup disk and system restored.

  I'm looking for some advice on how to restore a windows xp installation software raid 5 that was running on my XP system. I had a problem when the startup disk has failed, but I was able to backup the system before it can. I replaced the drive and restored the system and everything came, but I was not smart to do this and accidently left the readers connected when restoring raid. I don't know if windows has done something when I tried to install XP on the new drive, or maybe something else has happened when I restored the system from the backup, but my raid drives can not be used. There was a moment in the restaurant business I saw a message on the MBR, but I thought that was just for the drive being restored. I didn't have a single player who held any information on the other disks in the system, but I'm not 100% sure on that.

  When the system boots the windows logo screen takes 10-20 minutes before you get on the desktop. Windows Disk Manager takes 20-30 minutes to fill the list of drives and status on the disks three raid is 'dynamic' and 'unreadable' is not reassuring. I suspect it's a problem MBR or partition table that must be corrected before trying to reactive the raid, but this is just speculation.

  The raid drives are on a promise ide/scsi disk and make it appear to start correctly with names and sizes. After that I get nothing. I do not have another scsi controller (or), but I thought I'd try active @ partition recovery to see if she can find information on the disks.

  I hope someone has some experience with recovery like this, because this is a first for me. I thought I was pretty sure running a raid-5, but wouldn't you know, the tech gods have found a way to crush my plans...

  Thanks in advance for any help!

  Hello

  Thank you for visiting the Microsoft answers community site. Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please ask your question in the TechNet Windows XP IT Pro Forums.

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

• How to configure Windows to allow the parameters and software downloads to appear in system and standard user administrator?

  I HAD TO REINSTALL WINDOWS VISTA (SERVICE PACK 2) DUE TO A TROJAN HORSE THAT ATTACKED MY SYSTEM. I USED THE SUPPLIED RECOVERY DISCS SET WITH MY COMPUTER BECAUSE THE SOFTWARE HAS BEEN PRE-LOADED AND I HAVE NOT RECEIVED SOFTWARE FACTORY. WHEN I WAS SETTING UP USER ACCOUNTS, I CREATED THE ACCOUNT TO ADMINISTRATOR (WITH PASSWORD) AND A STANDARD USER ACCOUNT. WHEN I CHANGE THE SETTINGS IN MY COMPUTER IN EACH ACCOUNT, IT DOES NOT APPEAR THERE EITHER ACCOUNT. I DO CHANGES IN PARAMETERS OF EACH ACCOUNT INDIVIDUALLY. CAN I SET UP SO THAT WHEN I CHANGE THE SETTINGS, IT WILL DO THAT IN THE TWO ACCOUNTS? THANK YOU FOR YOUR HELP.

  original title; HOW TO CONFIGURE WINDOWS TO ALLOW THE SETTINGS AND SOFTWARE DOWNLOADS APPEAR IN ADMIN SYSTEM AND STANDARD USER?

  Most PC manufacturers who don't give you the disks give you a partition on your hard drive that contains the images of the disks so that you can burn yourself.  You should check out.

  When you say "change settings in both accounts' exactly what are the parameters what do you mean?  It is normal that many Windows settings to be on a per user basis.  For example. the desktop background is a 'definition' which is completely independent for each user.  You cannot set up a wallpaper for a user and hope that it displays desktop of another user.

• How to assign a screen configured messaging task in the workflow

  Man of me but I can't seem to find the solution for this.

  I created a whole screen for task and together the screen created a messaging for the new job template.

  Then I add a task of e-mail to a request workflow, but nowhere can I find a screen parameter which defined the task of e-mail must use.  The properties of e-mail has a drop-down list for which model to use, but it has only one value: e-mail task and who uses the Standard Messaging task.

  I missed a setting that allows me to decide what model/game screen it should use?

  Thank you

  .. Mick

  Hi Mick,

  I guess you missed a step - you must assign the new model to a particular file type "Task - email task" (200).

  Reach

  Admin-> system-> System Administration-> the Types of messages

  and assign to this model.

  After that, you should be able to specify the new e-mail template in e-mail task.

• Do I need a fieldbus Configurator software?

  Beginning of I m to learn more about the Fieldbus Foundation and I'd like to develop a simple Visual Basic application to automate the calibration of analog input of fieldbus instrument, for example, set with a standard 1 Volt in the analog input of fieldbus instrument and read the value displayed by the instrument using the API OR-FBUS and my Visual Basic program.

  Do I have to buy a NOR-Configurator of this network of simple fieldbus H1 with a single field device and and NI USB-8486 interface?

  It s is not clear to me if I need a Configurator, for example, with a new instrument of Fieldbus needing to adjust some parameters with NOR-Configurator before using the API OR-FBUS Communications Manager in my Visual Basic program.

  I've seen a few old messages that you want to sell a Configurator API. Do you still sell this API?

  My intention, if possible, is to build an application that does not require installation of a fieldbus Configurator software.

  NOR-FBUS software consists of two components, Communications Manager (CM) and Configurator.

  CM provides a basic API for access to the network of FF.  You can create your own application of Fieldbus Foundation with the API.

  Configurator is a graphical tool to long for the full configuration. You don't need to build the application.

  CM (VB, VC, c#, VB.Net) APIs supports the following Basic configuration tasks.

  -The list interface, device, function blocks

  -Block/playback device tag

  -Read and write parameters by name or index

  -Read the alert data and trend

  I think that the APIs are not enough for your simple VB application.

  You may need to use the Configurator if you need the following features.

  -Get and set the device address

  -Put the tag block/device

  -Configurator and download Application Block function annex

• When you try to connect to a wireless network I get this error: "If you want Windows to configure this connection, start the Wireless Zero Configuration service.

  original title: WiFi

  I want to connect to a wireless network on my laptop. When I go to the page of networks wirelss under the "choose a wireless network" it says "Windows cannot configure this wireless connection. If you want Windows to configure this connection, start the automatic Wireless Configuration service. My other laptop does not, and I don't know how to make the wireless network options appear. Any help is appreciated!

  Hi AshleyHenley,

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You have security software installed on the computer?

  See the article and run the Fixit tool available, check if it helps.

  Error message when you try to run the Network Setup Wizard update for Windows XP Service Pack 2, Service Pack 3, or Windows XP Tablet PC 2005 Edition wireless

  http://support.Microsoft.com/kb/871122

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  http://support.Microsoft.com/kb/870702

• Can you assign the time of windows logon minutes rather than hours?

  Can you assign the time of windows logon minutes rather than hours?

  If you are referring to the TIME parameter net user, which is limited to increments of one hour.

  If you want to control (and the ability to force logoff as well), you will need to use a third party software.  Access Boss a 15 minute granularity.  I'm sure like many other applications, probably some of free.

  If you only want to restrict Internet access (rather than access to the computer itself), your router may be able to restrict access with granularity to minutes.  "Parental control" software, such as NetNanny, also restrict Internet access, although that usually not at the minute.

• Failed to install KB2898785. Error, "updates were not correctly configured. Returning from the changes.

  32-bit o/s. Vista Home Premium. All scans/checks indicate no problems

  "Updates were not correctly configured. Restoration of the changes. ....." Advice please?

  M/S Rep told me that the (free) support for Vista is no longer available. Could the problem of security identified in the software of M/S already affected my system (published 12/10/2013 refers)?

  Hello

  I wish that refer you to this article-

  https://support.Microsoft.com/kb/949358/en-us

  Note: Make sure that you get the computer back to the Normal start once you have completed the troubleshooting steps.

  Make sure that you back up the data on the computer before you continue.

  Thank you.

• windows\system32\config\system\file is damaged or missing, system will not start, I have not connection wired, software was on the laptop at the time of purchase

  system will not start, I have not connection wired, software was on the laptop at the time of purchase.

  Hello

  There is no Windows Vista downloads available from Microsoft.

  You can contact your computer manufacturer and ask them to send you a set of recovery disks.

  They should do this for a small fee.

  And if you have never received a recovery disk when you bought your computer, there should be a recovery Partition on the hard drive to reinstall Vista on how you purchased your computer.

  The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

  Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

  Ask them to the proper key sequence.

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And once the operating system is installed, go to your computer manufacturer's website and get the latest drivers for your particular model or laptop computer.

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon.

• Assign the server a static IP (static local, internet)

  I use the linksys router in my office. WRT54GS V4

  I have T1 line and my ISP is an IP address static 5.

  The DHCP option is enabled in my router. My server is connected to the router.

  If I set up my server with the static IP my ISP provided, my server will not connect to the internet.

  It seems to me that the only way to assign the static IP address to my server's getting a switch/hub

  and connect my router and server to the switch/hub.

  Or disable DHCP and configure networksetting for each n my Office PC. In this case,.

  I need to assign some with local and other IP with static IP address. Can it work?

  If you have any suggestions, let me know.

  Thank you.

  The WRT54GS is a consumer router. It does not support multiple public IP addresses.

  The only way this will work is the way in which you have already found: connect a switch to the conduct of the internet and then connect the server and the internet port of the WRT to the switch. Of course, make sure you configure the firewall on the server very well as it is fully exposed to the internet.

  Otherwise, you will need to get a router which supports multiple public IP, for example the Cisco Small Business series addresses or better.

• Do I need to use the software provided with the wireless hardware to go wireless? __

  I have a router Linksys Wireless (wrt160n) that I am not using. I whant to buy a (Linksys WUSB600N) for my office. I want to know if I need to use the software supplied with the hardware, or can I just use Microsoft Wizard to configure my network? Operating system is Vista Premium.

  Thank you Jeremy will do.

• Dependent Service in UCSM material of blade profiles? Is that we can assign the same service to a B200M2 profile, B230 M2 and a blade of B200M3?

  Dependent Service in UCSM material of blade profiles?

  Is that we can assign the same service to a B200M2 profile, B230 M2 and a blade of B200M3?

  An example: if my B200 M2 goes down because of a hardware failure, I replaced the same slot with a B200 M3 Blade.Then is possible that I have separate Service of B200M2 profile and associate the same Service profile with B200M3?

  Hi Deepak,

  It is certainly possible.

  If there is no problem, because of incompatibilities, it triggers a failed configuration error, the service profile is related to the new blade.

  I hope this helps.

  Thank you

  Michael

• Access restriction configuration network devices with the level of the ACS 5.0 user

  Hi Experts,

  I have some configuration tasks TACAC with level of different user for all routers and switches,

  To further develop, I engineer, analyst and site engineers, so I want to configure centralized authentication with Annie tacac different levels for the various categories of network engg. Analyst, site engineer,

  can someone explain about how to proceed with ACS 5.2 and what configuration is required at the peripheral level.

  I'm particularly looking for the 5.2 acs configuration procedure.

  Looking forward to get the answer.

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.2/user/guide/policy_mod.html#wp1076053

  In "default device admin" just create authorization rules.

  They should look like "If the user/group type = site engineer, then assign the shell profile X.

  You then define the profile of shell in the elements of policy and put in there all the privileges of your engineer to site.

  And so on for the other roles

• Is it possible to assign the DHCP pool to a specific SSID?

  Hi experts,

  I wanted to know if it is possible to assign a DHCP pool to a specific SSID on the Cisco Aironet 1142. If so, what commands do I need to implement?

  Thanks in advance.

  concerning

  Fari

  We can directly assign the DHCP for the SSID pool, we can map the SSID to a VLAN and this subnet VLANS can be configured for the DHCP pool...

  If this client that connects to the SSID will hit him VLAN and then this VLAN the DHCP is reset...

  On the access point, you can configure the DHCP pool or even on the switch or L3 device or server...

  Regrads

  Surendra

• I bought the Adobe Photoshop CS5 and Lightroom 3 on a CD. However, I now have a 3 Surface Pro who does not have a CD player. Please give me a way for software downloaded from the internet. Thank you.

  I bought the Adobe Photoshop CS5 and Lightroom 3 on a CD. However, I now have a 3 Surface Pro who does not have a CD player. Please give me a way for software downloaded from the internet. Thank you.

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a link to access a page to download the Adobe programs if you do not have a disk or drive

  -Cloud desktop http://helpx.adobe.com/creative-cloud/help/creative-cloud-desktop.html

  -Cloud Getting Started https://helpx.adobe.com/creative-cloud.html

  -you will need to enter your original serial number during the installation for non-Cloud programs

  - or kglad links in response to #1 here can help https://forums.adobe.com/thread/2081216

  Also go to https://forums.adobe.com/community/creative_cloud/creative_cloud_faq

  IF Windows 10 read below

  Cloud & Win10 https://helpx.adobe.com/creative-cloud/kb/Windows_10_compatibility_FAQ.html

  -In addition, only CURRENT products will be tested and updated for compatibility with Windows 10

  - so if you have an older program, update you to Windows 10 at YOUR risk of problems

  -You can get CS6 and previous programs to install and run, or you can not (some do, some don't)

  -IF not, Details of the message from the error messages and a person may be able to help (just not Adobe)

  An idea that MAY work to install or run some programs in Windows 10 old... works for some, not for others

  -http://www.tenforums.com/tutorials/15523-compatibility-mode-settings-apps-change-windows-1 0 - a.html

  - or run as Administrator http://forums.adobe.com/thread/969395 to assign permissions... said FULL yet, but sometimes it is necessary for all Adobe programs (this is same as using an administrator account)