Constant crash on export

Similar Questions

• Constant Crash logs and unusual behavior spotlight?

  Mac Book Pro (early 2011) 17 "quad i7 16 GRAMS / 500 Gb Crucial SSD MX200

  Hello

  I get constant crash messages in my console. There is a behavior unusual spotlight as well.

  It all started with a hint of delay and backup times with reading of error message "Impossible backup, please try again later"

  Spotlight is indexing for long periods of time. Research presented so I tried these possible solutions.

  1 (obvious) adding hd/external references to the list of privacy then removing to re-index... No.

  2 disable indexing with the terminal and re-activation controls... No.

  3 find 10.7.5 additional updated with the hotfix for extended projector or activity of time machine,.

  then focus on disabled,

  ran disk utility to repair permissions,.

  welcomed my backup run and assumed all was well. I thought that I re activated spotlight and the problem has been resolved, but apparently my console suggested projector has been disabled so I have reactivated the indexing and have had some problems of backup again... (continue)

  During my diagnosis, I consulted a friend who looked at my console. He mentioned disk i/o errors and I have maybe need to replace my hard drive soon - I was considering upgrading ssd anyway - so I did the installation and upgrade of RAM.

  Now, my attention is directed to my messages to the console.

  I get the minute incident reports or more. mdsworker showing an invalid address (?-?)? I don't have a lot of knowledge in regards to the console and how to read the messages, but I do not recognize the word or the fault accident. Any help is appreciated. Can't post a report if required. Thanks in advance!

  It seems too short to be a report, but perhaps a summary? A lot of these...

  30/05/16 11:02:43.316 PM ReportCrash: com.apple.message.domain: com.apple.crashreporter.writereport.crash

  com Apple.message.signature: mds

  com Apple.message.signature2: UNBUNDLED | ??? (???)

  com Apple.message.signature3: FAB1F6BC2EBB82D0BC47F031B7127505

  com Apple.message.Result: No.

  com Apple.message.summarize: YES

  Check if the MBP had the kernel panics.  If so connect and confirm it with these instructions:

  https://support.Apple.com/en-us/HT201753

  Ciao.

• Dell order configure 3.1.0.250 crashing during export to exe

  Dell order configure 3.1.0.250 crashing during export to exe. I tried on two different machines with the same result. I have .NET Framework installed 4.5.2. Here's the report from crashing Windows.

  Signature of the problem:
  Problem event name: CLR20r3
  Signature of the problem 01: cctkgui.exe
  Signature of the problem 02: 3.1.0.0
  Signature of the 03:559147 c 2 problem
  Signature of the problem 04: WindowsBase
  Signature of the problem 05: 4.0.30319.34209
  Signature of the 06 problem: 5348b4e9
  Signature of the 07 problem: f61
  08:6 problem signature
  Signature of the problem 09: System.InvalidOperationException
  OS version: 6.1.7601.2.1.0.256.48
  Locale ID: 1033
  Additional information 1: 6d8c
  More information 2: 6d8c9c0d6ed9fe2f95cec4737399f068
  Additional information 3: J183
  Additional information 4: d18349a1ed7c01d977b9ab4c0697af85

  After posting the answer, I tried to create an exe from the package of local system and leading to an accident too.

  And also, when you asked for the model of the platform, if you meant what systems the package will be deployed on, his will mainly be on Optiplex 9020 and 9010 s.

• Frequently asked questions of ApphangB1 causing constant crashes in Mozilla Firefox

  Original title: I use firefox for my university studies. I now have recurring questions of ApphangB1 causing constant crashes please help?

  I use firefox for my university studies. I now have recurring questions of ApphangB1 causing constant crashes please help?

  Hello

  1. the problem persists with Internet Explorer?

  2. were there any changes (hardware or software) to the computer before the show?

  You must contact Firefox support for assistance.

  http://support.Mozilla.org/en-us/home

  Hope this information helps.

• Crash on export

  Well, it is a frustrating day.

  I have the last CC of Lightroom, I think it is 6.6.1 operating on El Capitan 10.11.6.  iMac 5 k.  Most of my photos and my library/catalog is on TB2 external drive of Gtech TB 8.  I upgraded the RAM through 16 GB to 64 GB OWC

  I tried to export 81 photos of LR.  For the last 2 days.

  Before this started, I had no problem.  Same process, same computer.  I could export until the cows come home home.  I did the update CC 6.6.1 thinking that might solve some bugs.  But it does not.

  That's what I know so far:

  * I can be in LR, and it doesn't crash.  Mainly just when I export and about half way through.

  * When it crash, mouse is black screen, does not respond for a second, then the error text white on black rebooting screen and iMac to the login window.

  * The last time I had console upward as the accident happened and the Console crashed everything first.

  * I did the repair disc on HD and external hard drive.  (no error reported on the HD, it seemed to fix something on the external, or it just took awhile)

  * What happens if I start with TB disk attached or not.

  * Yesterday (before the LR CC update to the current version), the iMac was sleeping on a black screen which would then become insensitive in LR (or creation).  Apple Genius looked through the code and cannot find whatever it is immediate, and it doesn't seem to happen when it is NOT connected to an external drive.

  * I changed the cables of TB, I unchecked "put hard drives to sleep" and the black sleep does not seem to happen now, but it always crashes on export.

  Someone knows something like that?  My next step will be to try to use another computer and see if it does the same thing when I load to the top of this library and the hard drive.

  Thank you...

  dj_paige after you isolate the problem to this computer with this RAM and read some other forums for a similar problem, seemed like the only logical problem was the OWC RAM.  I used the application called Rember to test all together and individually, and after hours and hours and days seems them 2 16 GB OWC sticks were bad.  They sent and 2 replacements.  After graduating from the successful with two pieces of RAM testing, I kept those and refer others.

  Downside is that it kept crashing and losing days of my time.  Upside is is not in the software and I can export until the cows come home House now...

• Adobe Premiere Pro cc 2015.2 crashes when exporting

  From one day to the other, Premiere Pro has crashed during editing, but worse: it crashes when exporting.

  Things usually never did not, all of a sudden fool you.

  I've updated my graphics driver, I cleaned my Cache of media, I did a complete reboot and still it crashes. It's a fairly simple change, not even a true documentary, but I can't seem to export

  What is the problem?

  Using Windows 10, i5, Radeon AMD R9 - 270 2GB16GB DDR3

  everything worked great until this week

  Try to create a new project, import the old one in.

• Media Encoder crashes when exporting from Premiere Pro

  Media Encoder crashes when exporting from Premiere Pro. I am the queue several files to export and Media Encoder will crash. The computer system has 32 GB of RAM and videos of export fine in first, but which requires export each individually. Each video file turned down and some can be quite long (more than 3-5 hours). Nothing else is running on the computer that take over memory.

  No idea why Media Encoder will crash?

  Try turning off the GPU acceleration.

• System crash on export

  New Mac Pro 2014

  10.9.3 OSX

  3.5 ghz 6-core intel xeon ARE

  and over-pants D700

  Current updates with CC - full range

  Complete system crashes when exported in Premiere Pro. The Finder window is disabled and I have to hold the power button / stop.

  Also problems with Davinci Resolve - they said osx 10.9.3 is the reason and that there is no solution until Apple release 10.9.4.

  Any help or advice would be greatly appreciated that I make my living with these editing programs.

  Yes, I have. Thank you. I had no problem with artifacts - that's the problem which is that I have.

• Crash when export - I tried to export my sequence first and SOUL and it crashes - Pls help.

  Crashing during export - I tried to export my sequence containing several first clips and SOUL and it crashes - Pls help.

  Need someone to help... more information please click below and provide the requested information

  -Premiere Pro video Editing information FAQ http://forums.adobe.com/message/4200840

• What can I do to stop Adobe Premiere Pro CS6 crashing when exporting?

  Without worrying about whether I have a new project file or an existing one, changes or no retouching, whenever I click on export, Premiere Pro simply crashes.  Same for Media Encoder - cannot open this same one.  I have all the latest updates installed cs6, the computer is new for two weeks - OSX 10.9.1, NVIDIA GeForce GT 1024Mo of 650 M.  The only way I've been able to export is through a back door: I use the dynamic link in After Effects and then returned to my sequences it.  Help?

  OSX Crash http://helpx.adobe.com/creative-cloud/kb/ame-premiere-crash-launch-export.html

• First Pro CC crashes when exporting h.264

  I have shot some footage in AVCHD using a panasonic hmc80, edited two sequences in the same project, a short about 8 minutes, which I exported to the fine H.264 format and a second in 36 minutes that crashes when exporting h.264, exporting to approximately 8 to 10 Mbit / s.  I have tried mpeg2 and exported correctly.  I updated from the first and windows and checked drivers such as Nvidia, all of this to date.  I use a matrox mxo2 as an e/s has no MAXIMUM.  Same Setup worked well with first cs6 for about six months without any problem. It is a windows system 8 I7 with 4 disks in raid zero for media and a separate player previews and export.  I also tried the FLV and it also crashed.

  The error message Windows "Adobe Premiere Pro CC has stopped working" collects more information about the problem.  I press cancel on the error of the box and first stop.  In fact the same thing happened once while I was sitting right on the timeline, take a break, he did the same thing and stopped, I was not made or export or do anything.  I have closed all the programs, including my anti virus software to make sure that wasn't the problem, but kept stopping.  I used to do some audio adjustments on a few clips I've done in the past with CS6 hearing...

  I tried to open the project in CS6 but received a message that the project is damaged and cannot be opened. However, the project opens and plays fine CC where I created it originally. I have inspected the timeline and made the small part of locations that it stops the function of percentage completed without problem.  He stopped at 20 percent, 55 percent and 60 to 70 percent several times.

  Finally found the problem.  Hope this helps other casual users like me.  Originally when I started editing I dissociated video audio to audio specific modifications. It's a game of the game session only and talking heads were not in on it.  Once I finished editing I've linked audio video back together.  After I inspected carefully the timeline by zooming in to check every edit I was out of sync on one of my edits and he had a red - 4 video and a + 4 more on audio right on the clips.  After having to separate the tracks again that the red numbers went away and of course had an export successful h.264 after at least a dozen crashes.     What is funny about this is I had an export successful with mpeg2 after continuous h.264 and flv hangs until this fix.

• CS6 Indesign crashes during export epub

  My indesign cs6 crashes during export epub. I have windows 7. I uninstalled and installed again, but nothing happened. When I start to export with the kindle amazon program also plugin stops working, theoretically it is not a bug of amazon. What to do. Could someone help? Thank you. I have had no error message.

  I would post your problem in the forum here http://forums.adobe.com/community/indesign/indesign_generalInDesign. They will be able to help you.

• Photos crashes when exporting to the originals

  I have a library of 53 k and I am trying to export original for an extra layer of backup. All the originals are on Mac.

  When I try, Photos blocked pretty quickly. I tried to restrict the export of just pictures 2015 (about 6 k).

  Details of the accident:

  Process: Photos [1164]

  Path: /Applications/Photos.app/Contents/MacOS/Photos

  ID: com.apple.Photos

  Version: 1.3 (350.23.0)

  Generation information: PhotoApp-350023000000000 ~ 2

  Code type: X 86-64 (Native)

  Parent process:? [1]

  Officials: Photos [1164]

  User ID: 503

  Date/time: 2015-12-11 12:48:54.458-0500

  OS version: Mac OS X 10.11.2 (15 C 50)

  Report Version: 11

  Anonymous UUID: 38866DA9-77C4-B0A7-8CBA-E037AA9439AA

  Time since started awake: 100000 seconds

  Integrity of system protection: enabled

  Crashed Thread: the queue on the expedition 9: LiRequest concurrency control

  Exception type: EXC_BAD_INSTRUCTION (SIGILL)

  Exception codes: 0000000000000001 0 x, 0 x 0000000000000000

  Note the exception: EXC_CORPSE_NOTIFY

  After the first 50 lines of the accident report and all lines of the thread crashed.

  Also download and run Etrecheck.  Copy and paste the results in your response. Etrecheck is a diagnostic tool that has been developed by one of the most respected users here (and recommended by Apple's Support personnel) of the CSA to provide a snapshot of the system and help identify the most obvious culprits that can adversely affect the performance of a Mac.

  

• Adobe first/Media Encoder CC Crash when exporting video for ~ 25 min (Mac)

  Specifications of the laptop:

  OS X Version of El Capitan 10.11.4

  2.5 GHz Intel Core i7 processor

  16 GB memory

  Iris Pro 1536 Intel graphics card

  Problem:

  Adobe Premiere and Media Encoder CC constantly crash when I try to export the sequence of a project which is roughly ~ 25 minutes in length, H.264.

  The effects are used throughout the project, but only the base dissolves and black-and-white/contrast effects. Images comes from several sources, but all of the same mp4 file and type frame rates. There are also several PNG files in the Assembly, including the one I used to "frame" the movie to make it look more like images from other sources. Yet once, nothing complicated, not even a long dissolve (dissolved all is literally 2/24 frames in length).

  Split the video into sections and exporting separately are no problem, even when comparing a relatively short section of 4 minutes for a much bigger and more focused on the effects of section 11 minutes. Needless to say, I really, really, really prefer does not export this video into sections. The intended destination is youtube, and I just want everything in an own mp4, not two 12-minute videos.

  After some digging, I found similar problems reported on these and others and was especially deplore the possibility that my power supply is not large enough to cope, but it's still very confused. My MacBook is not 'stop', and as far as I could see, the Iris Intel Pro should have been sufficient even without a graph 5100 graphics adapter Pro 5200 or; as in the past I've already exported MUCH larger files, ranging from 35 to 85 minutes.

  solved by downloading latest driver for Nvidia CUDA for Mac - really just a problem with the Mercury playback engine. Guess OpenCL was not simply cut to get the type of work I was doing.

  Here is a convenient link to the latest CUDA for Mac drivers for all who encounter similar problems with export in Adobe Premiere Pro Media Encoder CC or CC: drivers CUDA for MAC Archive | NVIDIA

• The Premier Pro 2015 crashing on export

  Hello

  I have a MacBook Pro (chart below) under OS X 10.11.2 (El Capitan).

  Model name: MacBook Pro

  Model identifier: MacBookPro11, 3

  Processor name: Intel Core i7

  Processor speed: 2.5 GHz

  Number of processors: 1

  Total number of Cores: 4

  (By heart) L2 Cache: 256 KB

  L3 Cache: 6 MB

  Memory: 16 GB

  Boot ROM version: MBP112.0138.B16

  Version of the SCM (System): 2.19f12

  I tried to export a Premier Pro short (less), either on the pre-series HD or you-tube, which takes about 2 hours (seems excessive even if some parts of the video have several effects on it).  He gets almost all to the way of when there about 4 minutes to go (about 96% or almost thanks to export) the software crashes and I get the standard error message, "Premier Pro has met a serious error..." "and the closure of the software.  I tried this about 6 times and I am very frustrated.  I managed to export the exact same movie a couple of days, as a lower resolution file, so I'm a little confused about why this happens.  I deleted on more than 100 GB of my HD in case the problem was the lack of space, as well as on the external hard drive I was using as my work drive.

  I have managed to export different films and more time in the past, with the same settings and much faster, but maybe with less effect on the clips.

  I tried to export a clip different 30 sec short with the same parameters, which has been a success, but when checking the same activity monitor on the export of this little clip, CPU utilization for the Premier Pro has increased approximately 780% (I understand that it's okay?) and User CPU load approximately 95% and CPU system around 4%, so almost all in use.  The 16 GB memory available, that 11 GB of memory is used, with 4 GB of cache files - this maybe is the problem?  What I have to delete the cache and how do I get rid of these hidden files?

  I also tried to update the first pro and making sure that all my read/write permissions were right on records of Adobe, but none of them helped.

  Any suggestions much appreciated.

  Thank you

  Adrienne

  Computer stops using the resources GPU intensive applications