continuous reboot of failed reset
I had a broken screen and has been using the laptop with HDMI to my TV screen. I tried to reset the original hard drive to get rid of excess software and virus potential because he was slow. I didn't know that the computer would not automatically recognize the HDMI connected display. Then when I started rebooting, I lost the screen and couldn't do anything. I bought and installed a replacement screen that seems to work very well, but all I get is the white screen with the HP logo in the middle and a continuous restart loop. What can I do?
Hello
Can you post back with the full model number and your cell phone Nr - see here for a guide to the location of such information.
Kind regards
DP - K
Tags: Notebooks
Similar Questions
-
I just ran the last update for my iPad and now it just continuously reboots to the black screen with the Apple Logo. I left plugged in all night and still no change. Hard restarting does not help, neither do not connect the unit to aMacBookPro. When I do this, iTunes complains that it can not connect because the iPad 'expires '. Now it is disconnected, but I can't turn it off. Even close the lid will not extinguish it. Any ideas?
Try the following. It seems yo may have to let the battery drain is completely:
- iOS: do not respond or does not light
-Also try DFU mode recovery mode post-test
How to put iPod touch / iPhone in DFU "Karthik doodles."
-If failed and that you cannot completely turn completely the iOS device, leave the battery to drain completely. After loading a hour repeat the foregoing.
-Try a different cable
-Try on another computer
S ' there is still not successful that usually indicates a hardware problem and an appointment at an Apple store Genius Bar is in order.
-
forgotten that my bad startup password 3 times computer laptop reboot how to reset
forgotten that my bad startup password 3 times computer laptop reboot how to reset
Hello
In this case, you can use windows system restore to return the machine to a point in time before this prompt syskey occurred using the following method.
Use another PC to create a Windows 7 repair CD. Download the ISO from the link below.
You must use an app like ImgBurn ( Note: you can deselect additional software during installation of ImgBurn options) to burn the ISO to a CD - a guide on the use of ImgBurn to write an ISO on a disc is here.
Once created, type away at the esc key when you launch Notepad to open the Start Menu.
Insert the CD to repair.
Select the Boot Manager option ( f9 ). Use the arrow keys to select the CD/DVD drive and press ENTER - if you are prompted to "press any key to continue...". ", do.
Select 'Repair your computer' and follow Option 2 in the guide here to run the Windows system restore - choose a restore point at least 48 hours before the opening of session problem occurred.
Kind regards
DP - K
-
PowerConnect 3448P continuous reboot
I have two switches to PC3448P. That I've updated the bios and firmware no problem. The other, something must have been corrupted during the update process - the switch is stuck in a continuous reboot. The documentation that came with the latest firmware says:
If you try to upgrade from 1.0.1.13 or below, please
version of the software that 2.0.0.34 is downloaded on the PowerConnect switch
34XX series, as well as the new version of startup code 1.0.1.01. New firmware
and the new startup code must be updated at the same time. Failed to download
the new bootcode translates the system to reboot continuously. This
It will take a XMODEM from the previous version of the software download
(PowerConnect_34XX - 10113.ros) using XMODEM and the Start Menu for
recover.
I need to get a copy of the firmware "PowerConnect_34XX - 10113.ros" file to try to restore this switch to a working state, but I cannot fid anywhere. Can you tell me a download of this file?
Hello
Try this link http://downloads.dell.com/network/PC_34XX_v10113_A05_Firmware.zip
-
Help me please, my phone continuous reboot loop. This problem starts at 00:00 hours, I don't know what to do
Hi miltonjhon,
Welcome to the community! Since you are new, please make sure that you have checked our Forum.
Try to remove the SIM card from his cell phone and then restart it, leave the SIM card and see if the problem persists, if it stops then the SIM card is causing the problem.
-
BlackBerry Torch 9800 Smartphones continuous reboot cycle
Please can you help me? My Torch 9800 is stuck in a continuous reboot cycle. Press and hold the return key does not it in safe mode and my Office Manager does not even recognize the existence of the phone. Please can someone tell me how can I recover the situation?
Hello
Given what you describe, you should probably use these more drastic repair attempts:
- KB10144 How to force detect the BlackBerry smartphone using the Application Loader
- KB27956 How to recover a BlackBerry smartphone from any State
- http://CrackBerry.com/BlackBerry-101-lecture-12-how-reload-operating-system-nuked-BlackBerry
I hope you have a good backup, because in this case it is usually not possible to take one now.
Good luck!
-
Master reset PW does not work, continue to ask after reset
I forgot to master pw; chrome://pippki/content/ResetPassword.XUL used to reset, indicates reset successful; close FF 24.4.0; restart; FF calls again for the master pw.
./. Mozilla/Firefox/e052w6iw.default/signons.SQLite deleted
./. Mozilla/Firefox/e052w6iw.default/Key3.DB deletedreset the master pw again with the same string as above. FF calls again for master pw
RHEL 6
FF 24.4.0A reset will try to retrieve names and passwords and which might fail if the affected files are corrupt.
Delete the file signons.sqlite and key3db with Firefox closed should be sufficient under normal conditions and if there is no other (security) software interfering.
-
I have an AT 100, which starts at the home toshiba screen, waiting, vibrates, and then restarts.
I can get to the selection of start, but does not start to recover.
The selection of boot give me only 2 options mode android or recovery, both have the same result.
Can someone tell me the cause or better a solution?
Thank you
> I accesses the selection of starting, but will not start Recovery
You mean the hard reset, which can be entered by holding down the button works / stop and the volume up button?
I think that if this last resort does not help to interrupt the reboot loop, you will not be able to get the tablet work :( -
iPhone 5s stuck in a continuous reboot loop
My 5s iPhone has always been great. IOS is underway. My daughter used it yesterday evening at the stream of Pandora, but had finished and he's just sitting there. He started a continuous restart loop. I tried hard reboot (still a few cycles) and I tried to plug it into my laptop to synchronize with iTunes (never, give me the chance to enter my code to access, but iTunes gives me error that I did not enter my access code). I also leave the battery to choke and then restarted, but it's always just. I looked for answers and all seem to focus on the fact that this is happening for iPhones that have been jailbroken, but I has never been jailbroken.
If your iOS device restarts or the unexpected poster - Support Apple Apple logo
-
IPhone 6 more continuous reboot
Hi, my iphone guard reboot pls someone know what is the problem. All I see is white background with the apple logo. pls I need help
Have you tried to reset?
restore?
-
Y700 m2 upgrade - continuous reboot loop cycle?
Hi all
I recently bought a Y700 laptop with a 128 GB m2 and 1 TB hard drive.
I found that the 128 GB drive is just about acceptable, but as I do photography editing, the drive working essentially consumes the rest 30 GB I have free instantly. I would also like a little more room for manoeuvre for failing to manage the storage space so closely.
So I bought the following:
Samsung SM951 M.2 PCIe SSD 512 GB
SM951 Series MZHPV512HDGL-00000
Capacity - 512 GBI read NVMe version is not supported, but I assumed it would work.
I tried to use Acronis True Image clone/backup the existing drive, actually a recovery disc and used to restore the backup to the new drive. So far, everything seems to work.
However, after reboot, first of all, I got a BSOD message saying "Inaccessible_boot_device" and then the system reboots. At this point the loop starts, the screen shows the text "LENOVO" on black for about 10 seconds, switches and 2 seconds later goes on to repeat the process to infinity.
Thinking it was a problem with Acronis, I tried to use the Installation of Windows Media disc for just fresh install windows on the disk. Once again, everything seems to work and has been installed properly. However once the installation has been completed, once again reboot loop began.
I must add that when the loop runs, hitting F2 or any other key does not work, so I can't access the bios to tell the computer to boot from a key USB etc. To exit the loop, I have to power off the laptop and remove the offending SSD drive and then restart. At this stage F2 works, allow me in the BIOS to re - assign the USB as a boot priority to try to restore media etc.
I also tried to do "repair Windows startup", but after a few minutes, the repair process said that he could not repair the drive.
At this point, I wonder which of the following occurs:
1 drive is defective
2 - the drive is not compatible (material)
3. drive is incompatible because of outdated drivers (the laptop is 1 month old)
Any help you offer is appreciated, because I doubt now, I can return the drive given the way it has been used now!
An apparent difficulty has been to change the UEFI boot to legacy mode, but I kept the UEFI as first priority in the boot sequence. Things seem to work fine now.
Weird that the 128 GB m2 player provided by Lenovo was beautiful on UEFI, yet my 512 GB there is no work?
-
HP DV6000 laptop
-Intel Core Duo T2450 2 GHz
-1 g RAM
-Vista Home Basic 32
Portable colleague brought me, wouldn't boot Windows. Diagnostic hard drive with physical failure, cannot be accessed by car, even using Linux OS and Test drive.
I replaced the drive and used the HP to reinstall Vista drivers and HP system recovery disk.
After all, I'm having an issue where, after Windows starts, the system will restart spontaneously after about 30 seconds now. This cycle continues until the system is shut down. Problem does not occur when it is started in Mode without failure.
Has seen a similar post suggested reinstalling the RAM, which I did, but still have the same results.
Any suggestions?
Well...
After more than web hunting, found what seems to be the issue.
HP apparently uses a program called Manager of GUI of FBI to reinstall Windows, HP drivers and programs from the recovery disc. This program seems to be buggy, where after all has been installed, it is stuck in the reboot loop.
SOLUTION:
Start > run > MSCONFIG > startup
Disable RUNFBI
OK, restart
Will be no longer stuck in the loop of reboot of the system.
Delete the c: APPLZIP folder to remove the GUI of the FBI program.
Problem seems to be resolved, will display again if not.
Resolved on mine, but I hope it helps someone else with the same problem.
-
HP Solution Center not working after reboot (scan fails also)
My HP Photosmart 3310 software fails after a reboot, the day or the installation of the printer in Windows 7 64 bit. No error - it is said that installation is not completed and to connect the USB cable (it worked only 1 hour ago), or the printer is offline. I can reach the printer via IP (192.168.1.64 - static IP). The other computers in the House are printing and scanning very well.
Help I received via the software discussion and support forums is to re - install the software. I did it more than 20 times - it does NOT work. Let me repeat if you have not received this the first time - software does NOT solve the problem.
The scanner and the printer work fine after that the software is completely installed. The problem is that the printer and the scanner work not the next day.
Yes, I tried:
1. check the latest system and windows updates.
2. turned and on the firewall.
3. pull on the printer and connect via a USB cable. "" The installation is complete, but I can't run this way. The problem comes back the next day when I tried using the printer as a network through the router.
4 when I "add" the printer to Windows printers list, it causes the software HP Solution Center to enter the "incomplete installation error. Then, either the scanner or printer works, not both at the same time. Other computers work fine.
5. it's a brand new computer, if any old malware running.
6. I uninstalled, reinstalled, installed multiple copies, etc. of the latest version of the software from this site (AIO_CDB_FSW_Full_Win_WW_130_141) printer.
7. I ran the software patch network of HP, before and after the reboot, no real effect. (CPE_SLP_NETWORKMSI_hpcom_000_006)
Any help would be greatly appreciated.
Rich
I found a solution to the issue of scanner! I installed the software VueScan from http://www.hamrick.com/ , the software is designed for high end photo editing, so it's a no-brainer for her to scan documents. The free version works fine. If I wanted to the cost of the professional version of the $90 is nothing compared to the time I've wasted on getting the HP software to work.
To resolve the problem of the printer, I installed the driver through windows and bypassed the HP software. The only thing that miss me is now the ability to fax, but which can be performed directly from the HP Photosmart camera.
-
Pavilion ZV6000 AMD64 Athlon Windows XP error message after you connect to XP continuous reboot
Help! My Pavilion ZV6000 AMD64 Athlon Windows XP suddenly started a string that I can't stop without turning off the computer. Immediately after logging on XP, a quick screen comes up with an error, then it immediately goes into a restart. The screen flashes too fast to read. I get any user ID that I use. If I boot in safe mode, I get the same message. I rebooted on the windows cd, I restored to an earlier date, but nothing helped. When I try to get deeper, I wonder the administrators password. I tried all my passwords usual, including "admin" and nothing comes to me to pass the administrators password. I had this unit since then and have never done any hardware change. Is it possible to bypass the administrators password? I'm at a point of trying to re - install windows, but cannot. Any other help would be appreciated. The unit was new in Sept 05 and my 3 year extended warranty has just expired.
Of course, here are the steps:
Perform a hard disk of that test -
Installation of Service Pack 2 causes continuous reboot.
Vaio 2003 computers
Windows XP
Whenever I have install Service Pack 2, the computer restarts sporadically. It has something to do with the Service Pack and the fact that an error occurs at startup:
BIOS update incorrect data...
My computer will work fine without Service Pack 2, but some programs require that now. It may not by my RAM because the computer works fine without Service Pack 2.
ERROR MESSAGE ON REBOOT:
Windows has recovered from a serious error...
C:\DOCUME~1\Adam\LOCALS~1\Temp\WER77f0.dir00\Mini051010-05.dmp
is one of the mistakes.
Help, please!
WinXP SP2 should be installed no later than October 10 2006!
See...
Help: I got hacked. Now what should I do?
http://TechNet.Microsoft.com/en-us/library/cc700813.aspxPersonal data backup (which none should be considered 100% reliable at this point) then format the HARD disk and do a clean install of Windows. Please note that a repair installation (upgrade AKA on-site) will NOT fix it!
HOW to do a clean install of Windows XP: see method 1 and http://michaelstevenstech.com/cleanxpinstall.html#steps in http://support.microsoft.com/kb/978307
Once installed the clean, you will have the equivalent of a "new computer" in order to take care of everything on the next page before connecting the machine to the internet or one local network (i.e. other computers) otherwise and before using a flash drive or the SD card that is not brand new, or has not been freshly formatted:
4 steps to help protect your new computer before going online
http://www.Microsoft.com/security/pypc.aspxOther useful references include:
HOW to get a computer that is running Windows XP Gold (no Service Pack) fully patched (after a clean install)
http://groups.Google.com/group/Microsoft.public.windowsupdate/MSG/3f5afa8ed33e121cHOW TO get a computer that is running Windows XP SP1 (a) or SP2 fully patched (after a clean install)
http://groups.Google.com/group/Microsoft.public.WindowsXP.General/MSG/a066ae41add7dd2bTip: After getting the computer fully patched, download/install KB971029 manually: http://support.microsoft.com/kb/971029
NB: No matter what Norton or McAfee free trial which is preinstalled on the computer when you bought will be reinstalled (but invalid) when Windows is reinstalled. You MUST uninstall the trial for free and download/run the appropriate removal tool before installing updates, Service Packs Windows or IE upgrades and before installing your new anti-virus application (which will require WinXP SP3 must be installed).
Norton Removal Tool
FTP://ftp.Symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exeMcAfee Consumer product removal tool
http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exeSee also:
Risks & benefits of P2P file sharing
http://www.Microsoft.com/protect/data/downloadfileshare/filesharing.aspx
http://blogs.technet.com/MMPC/archive/2008/10/06/the-cost-of-free-software.aspxMeasures to help prevent spyware
http://www.Microsoft.com/security/spyware/prevent.aspxMeasures to help prevent computer worms
http://www.Microsoft.com/security/worms/prevent.aspxAvoid fake security software!
http://www.Microsoft.com/security/antivirus/rogue.aspxIf these procedures look too complex - and there is no shame in admitting this isn't your cup of tea - take the machine to a local, good reputation and stand-alone computer (that is, not BigBoxStoreUSA or Geek Squad) repair facility.
~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft
Maybe you are looking for
-
My son participated in a focus group and we found some very inappropriate responses have been sent and he attributed. We checked with the beneficiaries. My son, however, refuses their sending and, according to his reaction and the reading of what was
-
Satellite Pro L300D - 11 M - need drivers for Windows XP Home edition
Good afternoon! Help to find the drivers on the operating system Windows XP for Toshiba Satellite Pro L300D - 11 MThank you! If I have not clearly written something that you let me know please, I'm simple I do not speak English, I have Russian and to
-
HP Pavilion dv6-6138tx notebook PC
I am running Win7Pro 64-bit on the laptop above. [It was purchased with Vista pre-installed]. Device Manager says I have two devices without drivers installed, as follows: 1. a PCI device 2. an unknown device Windows Update does not help you, and I
-
I am trying to establish an ethernet connection from a windows to a SRS 100 CIG machine. It does not appear when I try to set it up on MAX. Should I have the real time module? The machine and the IGC are on the same subnet.
-
Hi all I have a little test lan with the installation of 2611xm for ipsec vpn. On each fe port I have a laptop plugged directly inside, int is assigned by dhcp, and outside at this stage is static. I use 3rd party ipsec client program shrewsoft custo