Control of the ZL62044 of Zarlink with NOR-4851

Similar Questions

• The volume control on the Satellite Pro A200 with Ubuntu 7.10

  I have a Satellite Pro A200GE-1F9, I did recently to dual boot with Vista and Ubuntu 7.10. It's the first time I used Linux and most things are going well so far.

  However, the volume control (a wheel at the front of the laptop) does not control the volume correctly with Ubuntu, rather than increase the volume smoothly as with Vista, it increases in a 1/8 of maximum volume jumps, the on-screen volume control is always smooth. I think that it is at least partly due to the change of a material volume wheel, as with the latest Toshiba, I have used, for a version of software based. It controls the system volume and runs continuously, without stop at maximum or minimum volumes.

  Does anyone know how to change this change in volume for a smooth jump?

  Thanks for any help

  Hello

  given that no one here has no idea, nor pilots, nor any information about the driver from toshiba support, nobody will be able to give you some useful information.

  Have you ever google and checked the ubuntu forums? According to me, which will bring you closer the source here instead.
  So just to start to ask in the ubuntu forums because I think that someone is there who maybe has the same problem as you.

  I hope that artistry a kind of programmer. ;)

  Welcome them

• Get samples of the clock machine (NEITHER with NOR cDAQ-9172-9422)

  Hey guys

  I'm trying to produce data for the position of a 1000 Hz all about stamping press with an absolute encoder which is connected to the NOR-DAQ.

  Two not that I am trying to program, but can not understand:

  (1) use a hardware clock to trigger the acquisition of the data at the selected speed

  (2) synchronize the three data acquisition modules I have to ensure that all data are received at the same time

  the material I have does not seem to have any counters. A few examples that I read would not go because of this.

  Any thoughts? If there is some examples/tutorials about this problem that I have missed please let me know.

  Thank you

  Hey, Rohan,.

  Thanks a lot for your help. I was talking to a National Instruments process engineer yesterday and it me that the problem was the vi calendar clock source option - instead of using AI/SampleClock, I had to use the time base of 100 kHz clock that did not appear in the list until I checked the option "ListAdvanced Terminal" in the name of e/s filtering dialog box. You must right-click the constant/control of the source of the clock and select I/O name filtering to open this dialog box.

  Thanks for all your suggestions, I'll try to apply it and check the performance.

  Nik

• Control of the network of HP with the trademark symbol is activated but not available in the add-ins.

  HP Pavilion with Windows 7 (64 bit) upgrade IE11 (64-bit and 32-bit).  Why HP Network checker with the symbol of the brand activated but listed as unavailable in Manage Add-ons. There's another one without the trademark listed under HP which is activated and available? I ask because the HP Network Auditor (cannot display this Web page) bleeding or only at half way showing / which covers a part of the Web page I'm on... example ehow webpage. This has just begun, I think I'm on the 64-bit now, if I go to help, about Internet Explorer it is not to say if I use 64-bit (or longer).

  Hello again pleaseneedhelp,

  And the page displayed correctly now? Initially, you said "I ask because the HP Network Auditor (cannot display this Web page) bleeding or only to half way showing / which covers a part of the Web page I'm on. I'm curious to know whether or not the Web page displayed correctly now?

  I'll wait for your answer. Thanks for posting on the HP Forums. Enjoy the rest of your day!

• Why is it not possible to use SIRI on my apple TV remote to control the HomeKit products? I should be able to control all the devices with my Apple TV remote and SIRI HomeKit!

  Why is it not possible to use SIRI on my apple TV remote to control the HomeKit products? I should be able to control all the devices of HomeKit with my SIRI voice remote control and using Apple TV!

  If the new apple TV can act as a concentrator HomeKit and I use SIRI on my iPhone to control my locks, thermostat, lights, etc. Why am I not able to do the same thing with SIRI via voice commands on my Apple TV remote? When is this going to work?

  Also, when Apple will come out with a response to the echo of Amazon? I've tired to wait... do it already! If you build it, they will come...

  Thank you!

  This is a community to a user, and Apple will not see your rant. If you have suggestions about Apple TV, Siri and HomeKit the best thing to do is to submit your comments here. http://www.Apple.com/feedback/AppleTV.html

• Using Firefox 7.0.1; having problems with hotmail. Cannot click on controls at the top of MSG, which is New, reply, delete, etc.. Can click on the same commands @ the bottom of the problem w/no MSG. Also cannot click on Inbox folder once I have access to

  Using Firefox 7.0.1; having problems with hotmail. Cannot click on controls at the top of MSG, which is New, reply, delete, etc.. Can click on the same commands @ the bottom of the problem w/no MSG. Also cannot click on Inbox folder once I have access to another folder. All known solutions?

  This problem may be caused by the Yahoo! toolbar as scopes as well down and covers the top of the browser window, allowing links in this part of the screen not clickable.

  • https://support.Mozilla.com/kb/troubleshooting+extensions+and+themes

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the extensions or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > appearance/themes).

  • Makes no changes on the start safe mode window.
  • https://support.Mozilla.com/kb/safe+mode

• How to control of the screen with a list of scroll-able patch?

  It's probably something simple I'm missing.

  I would like to have control of the screen that displays a scroll-able list of all patches in my Concert.

  Usually, our band adheres to the order of our list, and I can increment/decrement my way through the list.

  But there will always be exceptions for last minute or queries or other changes.

  I would like a list scroll-measurement of the patches with visible in large enough performance mode fonts so that I can find and select in the right order quickly, without going to Edit mode and set my old eyes strain to try to read the list of the patches.

  I found this post looking for an answer to the same question, so I'm probably not much help (it would be really nice to scroll the list of patches with a hardware cursor!).

  I play in a band where the set lists change constantly (or we take queries on the fly), so I just keep all my patches (i.e. song titles) in alphabetical order. A little something (you may already know), is that if you are in 'Edit' mode, type the first letters of the name of the patch to it.

  I suspect it's one of those situations where there no place for developers some weird people would actually over a hundred patches in a concert.

• Weird problem with control of the ring and foot

  So I have some sort of weird issue with a control of the ring and a chart. I'm with LabWindows/CVI on a Windows 7 computer. The part of the program I'm looking at is basically to navigate through data - there are several "transition" (rehearsals experience), and you can choose the one that you want to watch in the list.

  Normally, you would select transitional in the list, it plots the data, then it is done, basically. However, all of a sudden (don't know how long it spent for), when I select anything except 'Average', he made all the tracing and such, then it changes control of the ring to 'Average' (it is not plot the average data or generate all the reminders that I can tell).

  Now the thing the more bizarre as you can see below, it seems that the switch happens just when I draw something on the chart:

  

   

  So, it's just weird. The code in this section is here:

     if(uidc.polyon) {
              polynomial_subtraction(curr_data, np, uidc.polyord, 0); // 0 Skip for now
          }
  
          // Scale the curr_data for gains, then pre-scale the FFT data
          // to have no change in the power spectrum (multiply by (2/np)
          for(j = 0; j < np; j++) {
              fft_data[j] = curr_data[j]*2/np;
              curr_data[j] = curr_data[j]*uidc.fgain[i] + uidc.foff[i];
          }
  
          uidc.fplotids[i] = PlotY(dc.fid, dc.fgraph, curr_data, np, VAL_DOUBLE, VAL_THIN_LINE, VAL_NO_POINT, VAL_SOLID, 1, uidc.fchans[i]?uidc.fcol[i]:VAL_TRANSPARENT);
  
          // Prepare the data.
          FFTEx(fft_data, np, npfft, NULL, FALSE, curr_fft);  // Do the fourier transform
  

  DC is a structure that I use to better organize some UI controls and uidc is for display RAM variables, then dc.fid is the Panel that is embedded in the tab "FID", dc.fgraph = FID_Graph and corresponds to the chart control. Control of the ring is actually in a child Panel, dc.cloc [0]. FID_Graph has a point, it can produce, but the reminder is empty (no not coded something there yet).

  I have also considered that perhaps something in another thread (I don't think there is, but whatever) I see is the cause, however, this behavior still happens on that line. I tried to break in different locations, on hold, then continues, as well by adding a loop containing Delay (0.01), a loop of 100 times. Always happens after the conspiracy.

  Does anyone have any idea why this might be happening?

  Hi Paul,.

  I don't have a solution, but I wanted to point out that, even if you see the ring to change its value only when you call the function of tracing, that doesn't say what this function call that really changes the value of the ring. In CVI, some drawing operations are batched, for performance reasons, and the Panel updates only visually at certain times. One of those moments when you draw a chart data. Yes, the ring changes visually at this time there, but it is probably just 'catch up' a change earlier.

  As you are looking through the code, when the value of the ring, you can use the term > command update UI to force the update panel, so that you don't have to wait for the tracing function and see if all goes well this change happening earlier.

  Luis

• How to calibrate the PCI-6110 with NOR-DAQmx

  Hello

  I am a new user of the PCI-6110 Council tries to run the calibration using LabVIEW procedure. I look at the document "Calibration" on the page of the manuals for the Board of Directors,

  http://sine.NI.com/NIPs/nisearchservlet?nistype=psrelcon&NID=11888&lang=us&q=FQL: 28locale % 3Aen % 29 + AND + % 28phwebnt % 3 A 1081 + OR + phwebnt % 3 A 7075% 29 + AND + 28nicontenttype % 3Aproductmanual % 29 + AND + % 28docstatus % 3Acurrent % 29% 20RANK % 20nilangs: en & title = NOR + PCI-6110 + manual

  One of the first steps in the document is to call the AI_Configure command to set the input mode, beach, etc. I'm using LabVIEW 8.5 with the NOR-DAQmx software, and I can not find the command (which, in LabVIEW, seems to be "AI Config.vi") anywhere. The calibration paper was written in 2003, and I gather from Google searches (please, correct me if wrong) that this command is actually a part of NOR-DAQ traditional, who was replaced by driver OR DAQmx.

  My question is this: what is the equivalent to AI_Configure command in the latest software? Is it perhaps a subsequent document describing how to calibrate using NOR-DAQmx?

  Thanks much for any help.

  Tom McLaughlin

  Hi Tom,

  The calibration Procedure series B, E, M, S, which is also linked from this page, describes how to calibrate the PCI-6110 with NOR-DAQmx.

  Brad

• Get lost with the controls on the panels

  Hi all,

  With the help of Lavwindows 2010

  I have a little difficulty with my UIR.  I inherited a project with several panels, 2 have about 340 controls on each of them, I'm looking at (for example) a certain (RATE) control properties. I use the tree Panel to get the table I want and the FREQUENCY control.  I double click on the name of the control RATE.  In the details (under the tree Panel) section, it shows the name of the constant is MLED_MAX12_2 and its status led (its really a digital slide).

  Is it just that CVI has trouble with panels containing a large amount of controls?

  Is there another way for me to access this control? (right click on RATE and by selecting OBJECT UI FIND gives me the properties of the control MLED_MAX12_2.

  Is there a limit to the number of controls on a Panel? of the project? File of the UIR?

  Thank you

  Pete Hedlund

  I couldn't reproduce it in 2010 SP1, so I tried in 2010, and I could reproduce the bug. This problem has been fixed in 2010 SP1.

  http://zone.NI.com/DevZone/CDA/tut/p/ID/12323#290057_by_Category

  The solution is to change the control in the edit control dialog box that appears when you click on , when a control has focus in the editor the user interface with the editing tool selected (as opposed to the tool of exploitation). Or you can double-click the control to display the edit control dialog box.

• Using a control of the chain with the Enter key, return * and * allowing repeated identical entry

  Hi all

  There must be a simple solution for this, but it's Friday afternoon, and my brain is not cooperating.

  I create a simple terminal through which a user can interact with an instrument. My question is about the only query string control. The button send and the Terminal Table are here for reference.

  

  Here is my desired behavior:

  (a) the user types a command in the field of the query, tape input or return. An event is triggered, and the request is sent to the instrument. The focus remains on the field in the query.

  (b) with any other action the interface user, the user types Enter or return again and again, by triggering an event that sends the request to the instrument every time Enter or return is typed. The focus remains on the field in the query.

  Here's what I have:

  

  This allows for one), but fails to b). The reason is, because the value of the field in the query has not changed, change value event does not fire when the user starts to spam keys enter or return. There is a way around this, as suggested by this post. Here is the solution in a few words:

  

  Instead of looking for the change in the value of the query command, the event fires for each key event to the bottom of the control and resembles a pressure of enter key or return. What attracts the user action, even if the content of the field of the request have not changed. The problem with this approach is that, when this event fires, I need to read the value of the query string order and send it to the instrument, but the value I get via the local Variable query is the old value, probably because the key down event fires before the value of query is saved as changed. Is there a way to programatically "enter" the contents of the control channel so it is recorded as a change in value, until I have the question via a local Variable? Is there a different way I should go about it? I'd rather not do anything that bound the input keys or return to this particular area, since I have many other UI elements that need these keys in my program.

  If not, is there a way to make the control of the fire 'Change of value' query string event when the user presses enter or return even if the value has not changed?

  Thank you for your comments!

  I thought about it.

  (1) control of the string (query) a value of update while typing.

  (2) save the key event down to the control of the chain. If the entry or return was pressed, send the state machine to the State 'send request '.

  

  (3) in the application 'send' State read control channel via the local Variable value.

  

  This is the desired behavior to allow the user repeatedly hit entry or return to regularly send a command, and the user can also type in a new order and send it by pressing enter or return.

  Thanks to all who have helped me this something to think about!

• In the VI library OR: extract, control of the channel numbers are loaded automatically every time that the VI is open with "count to five: a 2 three 4.0 five." Whence this string of data?

  Even after the removal of the string "count to five: a 2 3 4.» 5."since the control of the chain and its replacement by another string, the original string returns after that the VI has been saved then reopened. Whence this string of data? I have attached a copy of the library feature. In my application, I was able to work around the problem by replacing the chain with a constant string control. But I'm still curious to know what is happening.

  Thank you
  Chuck

  Chuck,

  Chain drive was scheduled by default with the string you see.  To change it, enter the new string, right-click on the control and select

  Operations on the data > default font of the current value

  Now, save your vi.

• Difficulty with returns control to the parents program after call asynchronous Subvi

  I'm trying to set up a directory of context-sensitive help for one of my programs.  This is the first time I tried an asynchronous call and I can't seem to make it work properly.

  The attached HelpDir.vi is the parent program that gives the user different help files to choose.  When the user selects a help file, its Subvi should appear.  I would like the user able to let this help file upwards and close the help directory or select another help file to upsimulataneously, if they wish.

  The strange thing is that, currently, this vi works exactly as I want if I stress execution on, but works normally, the HelpDir.vi becomes unresponsive when we help files was loaded and becomes sensitive again once the help file has been left.

  I set up the parent program with a structure of the event running asynchronous call and forget everything as in the example of the expedition to the France so I do not know why the program parent is not recover control after the launch of the Subvi.  Please take a look and let me know if you see what I'm missing.

  PS, You may need to update both static references.  I don't know if they break when you send the code this way.

  Thank you

  Tim

  Change your dialogues float instead of Modal.  Modal windows will always be on top.  In the changing Floating, then you can access the window of your main VI as well.

  Performance highlight should substitute somehow the disorder of modal window.

• I am not able to browse the network. The workstation services and control of browser will not start. The event log shows the workstation service terminated with error code 2250.

  Internet, not able to browse computers on the network

  The computer has internet access, but I am not able to browse the network. The workstation services and control of browser will not start. The event log shows the workstation service terminated with error code 2250. Also in the event log Workstation reports: could not load RDR device driver. Cannot run the sfc in safemode, gives the 0x000006ba error, the rpc server is unavailable. Runs under normal windows, noticed in the registry last run: 0x000003e3 error code (try adding c:\windows\system32\drivesr\i81xnt5.sys to the dllcache)

  I'm puzzled.

  Hello

  I suggest you to send your request in the below link.

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

• Sliding menu with target composition widget area overlays other controls on the page

  Dear users, I really need help with this, and sorry if I'm creating something repeated, but I cound not find another like that.

  I m working in a site with a sliding menu and two different modes (desktop and mobile).

  
  

  On the desktop computer:

  The sliding menu works very well and several other controls on the page or widgets work too. But the target composition´s box is greater than some elements and Don t enable these controls. I designed the page layout to avoid interference (in most cases).

  Mobile (cell phone):

  The sliding menu completely occupies the area of content and item target hides all items. For example, accordion on a layer below, for example, does not.

  Basically, I'm working with three layers: "Menu", "header", and "content". Navigation (such as arrows) are on the layer "header". The content (such as text boxes or accordions) can be found below, on 'content' layer.

  How can I solve this problem (without content leaving appears on the menu, change layers order).

  Thanks for the help!

  The container target if above other content then it would default behavior, you must work with layers and present the content to be active.

  Even with any phone, any content you want to view should go with the top layer.

  Thank you

  Sanjit