Corrupt VMs after power outage during the moved file

Similar Questions

• I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I tried the holding of 'command-r' and 'option' to see if the problem can be resolved or try any boot from a boot disk, my old backup, USB function start - but after a slow long process it all just stops.

  There is software on my HD that I don't want to lose by simply reformatting the computer, because I am now in a different country, far from my house, which is another problem of the Apple Store, to reinstall my OS from Yosemite on the www.

  Hey AmnonMikeCohen,

  Thank you for being a part of the communities of Apple Support.

  I understand that your Mac is not start properly after the power went out.  Let's start with resetting the SMC and NVRAM on your Mac and see if he can start from there:

  Reset the management system (SCM) controller on your Mac.

  How to reset the NVRAM on your Mac.

  See you soon.

• Power output during the disk check currently not able to boot to the desktop

  Power output during the disk check.  Now, does nothing.

  I started my system, he said to check the disc. The disk check began, he had run for a while. Then my power is out for a few seconds. Once the power was back on that I tried to reboot and nothing. The monitor shows no info yet. Just black says no signal and turns off. I have no option to boot or anything else besides. What I can do. Thank you

  Hello

  You did it of any material changes or software on the computer before this problem?

  You can connect the monitor to a different display port or connect another monitor if possible and check if it works very well.

  If the monitor is right, it implies that there is a problem with the graphics card or motherboard. In this scenario, I recommend you contact the manufacturer of your computer for help.

  Hope the helps of information.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Message "do not power down during the update"control panel screen not fade.

  Product name: HP ENVY 100 e - All - in - One Printer D410a

  Product no.: CN517A

  The message "Do not power down during the update" on the control panel of the printer refused to erase and remained perpetually disaloowing acess the Menu home for other actions as photocopies etc.

  I see.  I found this utility that will help you to solve the problem.  It seems the printer lost connectivity during an update firmware and glitch out.  The utility should take care of it.  Let me know what happens.

• I installed the download tool usb/dvd windows 7, but after you have selected the iso file when I insert the USB stick and refrecing, it does show that "no usb drive compatible' what is the problem with my USB

  I installed the download tool usb/dvd windows 7, but after you have selected the iso file when I insert the USB stick and refrecing, it does show that "no usb drive compatible' what is the problem with my USB

  I have sandisk cruzer blade USB key

  Hi Rohit,

  Thanks for posting your query in Microsoft Community Forum. I understand that your USB drive is having problems of compatibility with your computer, but I would like to learn more about the issue in order to provide you with better assistance.

  1. You did it any significant hardware or change software on the computer before this problem?
  2. When do you get exactly the error message?
  3. Have you tried to connect to any other computer on this flash drives?
  4. Your USB key works on other computers or have you tried to connect to different USB ports on this computer?
  5. Is the pen drive getting detected in the case or you are able to access the drive folder in the window of the computer ?

  The question may arise if the currently loaded USB driver has become unstable or damaged, or if your PC requires an update for problems that could conflict with a device USB and Windows. This can also occur if your USB controllers may have become unstable or corrupt. So, I would suggest trying the following steps and check if the problem persists.

  Method 1:

  Please try the fixit (s) provided below which will help you solve common problems associated with devices and USB ports.

  • Hardware devices do not work or are not detected in Windows
  • Diagnose and automatically fix the Windows USB problems

  If method 1 does not work, try Method 2.

  Method 2:

  Remove and reinstall all USB controllers.

  1. Open Manager devices by clicking the Start button, click Control Panel, click system and security, and then, under System, clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  2. In the list of the categories of equipment, locate and expand Bus USB controllers.
  3. Right-click every device under the Bus USB controllers node and then click Uninstall to remove them one at a time.
  4. Restart the computer and let the USB controllers get reinstalled.

  Plug in the removable USB device and test to make sure that the problem is solved.

  If the problem persists, go to method 3.

  Method 3:

  This method will install the latest drivers from device to your USB device.

  1. Click the Start button, type Windows Update in the search box, and then click Windows Update in the results pane.
  2. Click find updates. When the scan finished, click optional review updates.
  3. Click the check box next to the update, and then click install updates.
  4. If you are prompted, read the license agreement, then click I agree.
  5. Follow the instructions on the screen to download and install updates.
  6. If you are prompted, restart your computer.

  More information: Update a hardware driver that is not working properly

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• Power outage during Vista SP2 install; black screen on startup of the PC

  Hello-

  I have a PC desktop Gateway which is no longer start after a power failure has occurred during the installation of Vista SP2. The computer displays the progress at the bottom indicator, then, before that can display the login screen, the screen goes black, with a white cursor. CTRL-Alt-Del and Ctrl-Shift-Esc do nothing.

  I tried without success to the following:

  * Safe Mode/Safe Mode control guest - boots to black screen new
  * Startup Repair - told me there is nothing wrong
  * System Restore - tells me there is no available restore points
  * System restore the OEM DVD - can not find hard drive
  * Re-install this is disabled because I can't start Windows Vista-

  There are * all * options other than wiping the disc/lose all my data? The PC is in a remote area and backup drive is not an easy thing to achieve.

  The PC is no longer under warranty of the bridge, and I understand that Microsoft supports is no longer installs OEM of Vista.

  Can anyone help?

  Thank you

  -Andrew

  I can tell you how to make bootable disks, but you already have a disk.

  He has changed since good means of XP repair install from disk by booting from it.

  I would add that info to disk Bootable repair, just in case your DVD is a factory of one computer.

  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  It's Vista only repair installation option these days.
  It must be switched on!
  Not much use, is it!

  Good luck with it.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Download the ISO on the provided link and do a repair of the disc.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Above information shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista Startup Repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• After the power failure during the restoration of the previous day, cannot enter os or passed the password even in safe mode.

  Have laptop Dell 8100, recently used out of town on a wireless remote, installed updates 47 system.  Upon return home, tried to change cable modem I used before purchasing a desktop computer.  I could not the laptop to work on internet.  So I restored system he choose 2007 too far back, then tried to restore someday, when restoring back to the Sunday I was untangle cords and press the power switch on the surge protector.  Now, I can't even in the system.  Go to the login password that I've ever had, my son has changed in 2002 from Tower to the yankees and protected by to keep his friend out of it, but I've never had to use a password he would always automatically functioning screen icons until yesterday.  The second problem the remote while the screen flashed occasionally and would be less bright black with very low juror I would turn off and cool and could use it later.  It happened when he was 6 months old and they replaced the screen.  In the research I found it eventually the inverter is not the screen and found where to buy however, I can not connect to my system now.  I don't want a new laptop, it has been used very little has everything I need and more photos.  My son who has put a password in 2002 died.  I want to return to my laptop, replace and/or to the inverter.  Need to travel to work.  Unemployed and own building company.  How to remove password?  I've never used a password and don't want everything.  Want to right back to my machine.  When asking my password it says field is no longer round.  Don't know what that means.  I know that he renamed Yankee, I saw that when updating.

  The notion of 'Password' is to prevent any attempt to usurp the security it provides. If there is a quick and easy way to circumvent or to usurp the password protected system, then it would raise the question, what should a password?

  I'm afraid that if you've exhausted all the possibilities and are unable to find/recover your password, you will need to reformat the hard drive and reinstall the operating system.

  The Microsoft policy about lost or forgotten passwords .

• Problem starting after power outage

  I am running XP Professional. Last Nite we had a power outage and now I can't get my Dell E510 to initialize. When I reboot, I get a message that my hard drives cannot be seen. I tried holding F8, but it doesn't get me nothing, but the same message. Disc I tried diagnostcs but the computer says it can't see the disks. Any help would be really appreciated.
  Frankdarpa

  Hello

  1. What is the exact error message?

  You can check the troubleshooting provided in the link below steps to fix the problem.

  http://support.Microsoft.com/kb/321626
   

• Date system resets to 2002 after a stop during the night

  I have a Dell Dimension 4550 with XP operating system purchased in 2002. Computer work fine except after having turned it off during the night resets date and time system in 2002. After resetting in the configuration screen, it will keep the date until I stop from one day to the next one up to 2002. The error message only in the file is The Core Services service AG could not start due to the following error. The system does not find the specified path, how can I fix this problem

  When the system date and time are incorrect, then is a good indication that the battery on the motherboard needs to be replaced.

  the battery from the motherboard is also known under the name of the cmos battery and the bios battery.

  There are instructions on the net how to replace.

  most of the time its pretty simple to replace and the battery can be purchased where they sell watch batteries.

  You can remove the battery and get the model number or search for it in the manual of your computer or your manual online computers at its place of origin.

• Windows 7 BSOD after accidental shutdown during the update

  Stop computer accidentally during the update of windows. Now computer stuck in a loop of startup blue screen. Safe mode and windows recovery all lead to the blue screen. I don't have a recovery disk. What should I do?

  Hello

  According to the description of the problem, your computer is stuck in blue screen loop. So, I suggest you to create installation media by following the steps described in the article mentioned below and after that try to run automatic reapir.

  Download Windows 7 Disk Images (ISO files)

  After you create the Bootable USB key, change the boot priority and set it to USB. If you are unsure it is advisable to contact manufacturer FRO even. After changing the boot priority is trying to start your computer by using the bootable USB key.

  To run the repair to start the Windows recovery environment (WinRE), follow these steps:

  • Insert the Windows installation disc in the disc drive, and then start the computer.
  • When the message press any key to start from the CD or DVD is displayed, press a key.
  • If your PC does not automatically detect the media
  • When the computer reboots, read on screen for instructions that explain how to interrupt normal startup and access the basic input/output system (BIOS) configuration utility. Most PCs use the F2, F10, ESC or del key to start the configuration of the BIOS.
  • Looking for a tab in the BIOS configuration utility that is labeled boot order, The Options of Bootor Boot. By following the instructions on the screen, use the arrow keys to go to the boot order, and then press ENTER.
  • Locate the flash USB, DVD or CD player (this could be called removable device) in the startup list. By following the instructions on the screen, use the arrow keys to move the drive to the top so that it appears first in the startup list. Press ENTER. The startup command sequence is now changed to boot from the flash drive, CD, DVD, or USB.
  • Press F10 to save your changes and exit the BIOS Setup utility. Select Yes in the confirmation window. The PC will restart.
  • Select a language, a time and a currency, a keyboard or input method, and then click Next.
  • Click on repair your computer.
  • In the System Recovery Options dialog box, select the drive of your Windows installation, and then click Next.
  • In the System Recovery Options dialog box, click on repair your computer.
  • Click the operating system you want to repair, and then click Next.
  • In the System Recovery Options dialog box, click Startup Repair.

  For more information about System Recovery Options, see What are the system recovery options in Windows?

  For more information about the Startup Repair, see Startup Repair: frequently asked questions.

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Kind regards

• Problem with power settings during the opening of Windows Media Player 12

  Original title: power options Windows Media Player Exchange

  WMP 12 of opening causes the power option for monitor turn-off time to return even if the time is 2 hours 15 minutes. Tried to reset the value, value save, all electrical energy plans by making the same, nothing is done.  Other set values, for example disk hard turn off (never set) will be defined and stay together.  Would have someone seen this kind of thing?   Operating system is Win7 Professional 32-bit.  All available updates have been installed.

  Hi Jim,.

  Please contact Microsoft Community. I understand that you have a problem with the power settings when opening Windows Media Player 12. I've surely you will help solve this problem.

  To better understand the issue, I would need more information on your side.

  1. The problem only occurs when Windows Media Player is opened?
  2. Did you the latest changes on the computer before this problem?

  This problem might have occurred because of these reasons:
  1. incorrect power settings.
  2 conflict between third-party applications.

  I suggest you try the steps listed here and check if it helps:

  Method 1:
  Run Troubleshooter of power that will check if the basic power settings are set properly or not.

  Open the troubleshooter of power
  http://Windows.Microsoft.com/en-us/Windows7/open-the-power-Troubleshooter

  Method 2:
  If the problem persists, restore to the default settings for power management. Check if it helps.

  Note: try the following steps only if you have not tried before.

  Step 1:

  To restore to the default settings power management, follow these steps:

  1. Click Start.
  2. In the search programs and files box, type cmd.
  3. Right click on CMDand then click run as administrator.
  4. At the command prompt, type powercfg - restoredefaultschemesand then press ENTER.
  5. At the command prompt, type exit to exit the command prompt.
  6. Restart the computer.

  Step 2:

  Once the plan of power reset by default, you can create a new power plan and the same customize according to your needs.

  Power plans: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows/power-plans-FAQ#1TC=Windows-7

  Method 3:
  If the problem persists, set up the computer in a clean boot state, and check if that helps. Setting the system in a clean boot state will help you determine if third-party applications or startup items are causing the problem.

  How to perform a clean boot in Windows:
  http://support.Microsoft.com/kb/929135/en-us

  Note:  After the clean boot troubleshooting steps, see the "How to reset the computer to start as usual after a clean boot troubleshooting" section in the link provided to return the computer to a Normal startup mode.

  Hope this information helps. Reply to the post with an up-to-date report of the issue so that we can help you further.

• Automatic start after power outage - Inspiron 20 all-in-one

  I cannot find a setting of auto-start after power failure in BIOS, Inspiron 20. I really hope that I missed or can we make it happen another way. Someone at - it something?

  Thank you!

  Control Panel, system, advanced system, the boot parameters. But this isn't for the system failure power failure. Sorry - I read your post too fast.

  I don't think that today's computers can auto start after power cuts and even if it is possible, it is not recommended. Buy a battery backup UPS as APC must prevent interruptions of power failure and give yourself the time to shutdown properly.

• Appeare photos and videos have disappeared to a destination and the memory card folder after a halt during the transfer.

  I was downloading photos and videos from a memory card to camera in a USB card reader. After that most of the photos and videos (about 245 to 249) have been downloaded, asked me to jump on the last bit. Now, no pictures appear in the folder where I kept them or on the memory card. I get an error message when I try to eject the card reader. How can I recover pictures, because this is my only copy?

  Hi JanetSmart,

  • Have you tried plugging the card on another computer to see if it works fine it?
  • What is the file format of the file 29?

  It could be a virus, I would also say that you download and run the latest Microsoft Security Scanner to scan the card and check if it helps:

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: the data files that are infected must be cleaned only by removing the file completely, which means there is a risk of data loss.

  Response so that we can better help you.

• Power failure during the update of firmware for Color LaserJet 2600n

  Just in the middle of the update the firmware for my Color LaserJet 2600n, the power is out. Now I can't get anything to happen on the printer. The screen, or the power lights and the error light, but it does not work when the power is put on. I think that he wiped the previous firmware and either had not started or has been along the way in writing the new info. Is it possible that I can cancel it and reload the original firmware? It hangs on my MacBook Pro running OS 10.6.8. The only thing that the instructions seriously cautioned against a interrupt the installation. Needless to say, this is exactly what happened when the power is out. Any help would be greatly appreciated.

  Randy

  Able to understand me. Has proved to be quite simple. Powered off the printer and turn it back on and represented the firmware upgrade program. The printer didn't restart automatically, so I had to power off and wait 5 seconds before feeding this back. Once he recalibrated itself (which takes several minutes), I was in business.

• ENVY 100 printer D410 - screen says "Do not, power down during the update" permanently.

  I'm a Mac user Mavericks 10.9.1 running on a Mac Book Pro.

  I have a HP ENVY 100 D410 printer that works your for a few years.

  Recently, the LCD screen of the display on the printer offered, "there is a new driver. You want to update? "(Yes/no)

  (Or something close to that.)

  Unfortunately, I chose 'yes '.

  The printer then tried to update, but eventaully the LCD screen on the printer displays a flashing message:

  "Do not feed, down during the update"

  The printer now flashes just this screen continuously. The LCD screen will not display anything other than this message.

  The printer works when connected by cable and wireless. (Airprint works very well).

  I can scan documents, I can print pages, I can even access printers "Web page.

  But the LCD touch screen control panel is 'stuck' in flashing update message.

  I can't find any way to clear this error and allow the printer to complete the update.

  Help. Please, I beg you.

  Hello

  There is a fix to resolve the specific problem, but I'm afraid it is only available for earlier operating systems under OS X 10.5 and 10.6, Windows XP, Vista or 7.

  I you suggest to get a computer with any operating system supported, install the latest version of the software on the HP site using a USB and then follow the steps.

  The latest version of the software can be found below (the basic software should be sufficient):

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&OS=4062&product=4073738&softwareitem=MP-92513-1&sw_lang=&

  Make sure that you carefully go through the procedure to the installation section in the patch download page.

  Hope that helps,

  Shlomi