Corrupt Windows files, startup repair does not, blockages when touching a certain area of computer

Similar Questions

• Launch Startup Repair does not work

  Hi, the 'Launch Startup Repair' option does nothing for my installation of Windows 7 64-bit edition.  If I select the screen simply refreshes and presents me with the same two options - Launch Startup Repair and start Windows normally.  It's as if something prevents me to attempt any repair solution.  Anyway, which would cause Launch Startup Repair does not have to work.  Thanks if someone can advise.

  Hi, the 'Launch Startup Repair' option does nothing for my installation of Windows 7 64-bit edition.  If I select the screen simply refreshes and presents me with the same two options - Launch Startup Repair and start Windows normally.  It's as if something prevents me to attempt any repair solution.  Anyway, which would cause the launch startup repair does not work.  Thanks if someone can advise.

  Hello

  It may be damaged.

  If you have problems with the use of the built-in repair software:

  Make your own information system repair disc in this tutorial:

  "How to create a Windows 7 system repair disc"

  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  "This will show you how to create a system repair disc Windows 7 to be able to use to start the system recovery options to help recover your Windows 7 installation, if you have not a Windows installation disk, can't find your Windows installation disc or can not access the recovery options provided by your computer manufacturer.

  A system repair disc is not able to install Windows 7.

  Note

  If you are unable to start your Windows 7 to create a Windows 7 system repair disc, and then you could create on another computer for use on your computer. »

  _____________________________________

  Then, use this disk for System Recovery Options:

  "System recovery options".

  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  "How to run a startup repair in Windows 7"

  http://www.SevenForums.com/tutorials/681-startup-repair.html

  See you soon.

• during the installation of Vista Service Pack 2, the computor has been disconnected. Now, I don't have an operating system and startup repair does not work. What should I do now?

  Computor was disconnected during the installation of Vista Service Pack 2. I did now no operating system and startup repair does not work. What should I do now?

  You may have to reinstall Vista from the original media or from the recovery partition according to the type of computer you have.

  Hope that you made the backup recommended all of your data before attempting to install Vista SP2.

• Why my windows freeze and go does not respond when I try to install the msn photo on hotmail download tool?

  Why my windows freeze and go does not respond when I try to install the msn photo on hotmail download tool?

  The active x bar descends into the small window and freezes all windows open right there and will not respond. This happens when I open a new message and try to attach photos.

  Things I tried but has not made a difference:

  reinstalled IE 8, deleted the history of the browser, disk Cleanup, removed msn photo upload control, optimized IE8

  With xp media center

  PS. This occurs also at any time the information down to install an active x on any site control

  The only way to surf now with frustration is to use IE 8 NOT add optional

  So I fixed that on my own and that's how I did it.

  You must uninstall IE 8 completely which will bring you to IE 7 (in my case) and then install IE 8 via the site updates or microsoft.

  Uninstallin IE 8 by going to:

  Start--->

  Control Panel--->

  Add Remove programs--->

  Scroll down to IE 8--->

  Click on delete.

  IE8 updates must be removed also, if not then click the box 'To see the updates' on the top of the window to scroll down, look for the IE 8 security updates and delete.

  Resart your computer and install IE 8.

  This worked for me and may or may not work for you.

• Computer freezing and startup repair does not solve the problem.

  fix my computer when windows start dump then launch startup, but does not solve the problem. Can you help me solve the problem

  Hi Wwiese,

  Thanks for posting your query in Microsoft Community.

  I understand from the description of the problem, the computer freezes in the commissioning on the Windows 7 computer.

  I would appreciate if you can help me with the following information.

  1 were there any hardware or software changes made on the computer before this problem?

  2. are you able to boot into office?

  3. you receive an error message/code?

  I suggest you try these methods and check if it helps.

  Method 1

  Disconnect all external devices (printers, scanner, USB (universal serial bus) drives, etc...) Except the keyboard and mouse and then start.

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue. Then download drivers software updated for this particular device.

  Method 2

  Try to start in last good known Configuration and see if you can start very well.

  Using the last good known Configuration

  http://Windows.Microsoft.com/is-is/Windows7/using-last-known-good-configuration

  Method 3

  Start the computer in safe mode and check if the problem persists, if the question does not persist then perform the clean boot and check if the problem resolves.

  Step 1

  Safe mode starts Windows with a limited set of files and drivers. Startup programs do not work in safe mode, and only the basic drivers needed to start Windows are installed. Please click the below mentioned link.

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2

  Put the computer in a clean boot state to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  http://support.Microsoft.com/kb/929135

  Note: After completing the steps in the clean boot troubleshooting, follow step 3 from the link to start the computer to a Normal startupmode.

  Method 4

  If the problem persists, I suggest you perform a startup repair and check if it makes a difference.

  Startup Repair: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/Startup-Repair-frequently-asked-questions

  What are the system recovery options in Windows 7?

  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  In addition, you can do a System Restore the Windows Recovery Console.

  It will be useful.

  Let us know if you encounter problems with Windows in the future. We will be happy to help you.

• Tiara startup script does not work when running file associated with

  Hello

  I have a startup script that works correctly with tiara itself, however when I open a file associated with tiara (tdms files) the startup script does not work.  Is it possible to ensure that the script runs without worrying?  Thanks for the help!

  Bala

  Hi Bala,

  Depending on your use case, I suggest you call the next VI, which comes with LabVIEW, after your purchase VI is the creation of the data file.  Just pass the data file path in the upper part of entry and your path to the VBScript file in less than entry.

  "C:\Program Files (x 86) \National Instruments\LabVIEW 2013\vi.lib\ExportToExcel\DIAdem report Assistant Start CSC.vi '.

  Brad Turpin

  Tiara Product Support Engineer

  National Instruments

• Save to File.vi report does not work when integrated with the executable

  Hello

  When I use the NI_Report.lvclass:New Report.vi and NI_Report.lvclassave report to the File.vi, I can use successfully to create and excel spreadsheet so he was working at the developer.

  However when I build the source into an executable, this no longer works.  (The name of the file is built from the source, so I'm not using a dialog box)

  It can, however, create a .html file, but it does not seem as tidy.  Why is he not creating the Excel file?

  Running developer suite 2009, tried the .exe on Windows 7 and Windows XP with the same effect.

  Thank you

  -

  James

  See the attached zip file, it works for me here, see jpeg images and build the application accordingly and let us know. Did not include exe file, because the file size is too big.

• While the loop does not stop when the two values are equal using equal to comparitor

  Hello world

  I have a really, really strange bug. I have a LabVIEW VI that change a chain on a power supply. I have a start and a stop voltage and use a while loop to increment the device. For example if I want to scan from 1, 2V to 2.2 V in 0.2 V incremements, the program will end when "The current tension" = "stop the tension." And it works very well!

  However, when I start - 3 V and want to stop to say-0.8 (new in 0.2 V incremements) the program does not stop when "The current tension" = "stop the tension." I checked with the probe close to what should be the end of the race and - 0.8 V goes both of the entries ' equal to ' comaprison operator, but that his can't trigger a real result.

  It's very strange for me. Espeically as if I'm going - 0.8 V to-2 V but decrement of-0.2 V, the program stops correctly!

  I am very confused!

  See you soon!

  Search on: comparison of floating-point numbers

  The second thread is particularly relevant. This discussion was 2009, but you can find that the same "bug" being reported to enter the end of the 1980s.

  Mike...

• Computer turns on but does not boot to Windows, startup repair does not work

  When I turn on my laptop, it brings me to a screen titled "Windows Error Recovery" which means the following:

  "Windows did not start.  A recent hardware or software change might be the cause. »

  He asks me if I want to '(recommended) launch Startup Repair' or 'Start Windows normally'.

  When I select repair system, the screen turns off for half a second only and brings back me to the exact page as I was already on.

  When I select "Start Windows normally", he brings me to the loading screen that usually starts with Vista (anyone who says (c) Microsoft Corporation), except that it never stops loading.  I left for hours, and he was still on the same screen.

  I have a laptop Dell Inspiron 1525 with a processor Intel Core 2 Duo and Windows Vista Basic.

  Follow these steps to try to solve your problems of boot.

   

   

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Dell recovery options:

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=339949

  Above is Dell to reinstall Vista from the DVD on your computer.

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=336966

  And that way if you have a recovery partition on your hard drive.

  See you soon

  Mick Murphy - Microsoft partner

• BSOD: "a process or thread crucial to system operation has unexpectedly released or ended." Startup Repair does not solve the problem-

  I recently had a serious viral infection on my laptop Windows Vista SP2 Gateway.  After you run the antivirus AVG cleaner, who seemed to have had to quarantine or delete some files infected, System I couldn't Boot Windows to the top on this machine - even in the (all flavors of) Safe Mode.  When you try to start, I'd get

  a Blue Screen of Death with the msg of error in the title of this thread.  Before turning off the crash dump, the system indicated:

  ' * STOP: 0X000000F4 (0 X 00000003 0X85F22848 0X85F22694 0X82A26AB0).

  Other messages in the BSOD said I might have new HW causing the BSOD (I did not - but nevertheless I removed all external HW and tried again - got the same result).

  So one of the first things I did was to capture the startup log, so I could see what the pilots were hang up / does not.  Here's what I found:

  (1) the last driver to load (as indicated in ntbtlog.txt) was monitor.sys.  My understanding is that this indicates that when this driver loaded, the system crashed at this place - suggesting that there is 'something wrong' with this particular driver.  However, it seems likely, that I can use the screen/monitor (built-in) to the laptop without problem.

  (2) several drivers do NOT load: they are:

  1 NDProxy.sys

  2 Kvhfjgcv.sys

  3 Kbdhid.sys

  4 i8042prt.sys

  QUESTION 1: "Monitor.sys" being the last driver to load, should I assume this is the driver the system hung up on (that is, which caused the BSOD)?  And if so, that means I should replace this driver?  If so, how do I do that (how and where can I get a copy of 'Clean/good' of monitor.sys)?

  QUESTION 2: Is it possible to get "good versions" of drivers I listed above which was NOT loaded (I guess they didn't not load because they have been corrupted by the virus or the virus cleaner, or maybe just deleted by the virus cleaner because they were infected) to put into the Windows\System32\Drivers folder?  How?

  Here are the steps I took to try to fix the "corrupt system".  I inserted my Windows Vista DVD into the DVD drive and loaded Windows using that.

  Once that came, I then tried the following (and here are the results for all that I tried):

  (1) I selected the option "Repair", then choose "Microsoft Windows Vista" OS and press "next".  He tried to 'attempt to repair' for 15 minutes about, then finally stopped with a message: "Startup Repair cannot repair this computer automatically.  "Details of problem indicated: (a) the problem event name: StartupRepairV2." Signature 01: ExternalMedia; Signature 02: 6.0.6000.16386.6.0.6001.18000; Signed 03:6; Signature 04:131074. Signature 05: 0xF4; Signature 06: 0xF4; Signature 07:0; Signature 08:2; Signature 09: WrpRepair; Signature 10:5; OS version: 6.0.60090.2.0.0.256.1

  (2) I selected the option 'display diagnostic and repair details '.  He said that all tests successful (error code = 0 x 0), and

  then indicated the 'cause': ' unknown error checking: bugcheck f4, parameters = 0x3, 0x88607b80, 0x88607ccc, 0x82a78ab0. "

  - AND -

  Repair action: repair and checking the integrity of system files.  Result: failed.  Error code = 0 x 5

  (3) I checked that the restoration of the system, and even though I know I had some Restore Points created at the origin of this system, System Restore has indicated that there was no restore points to go back, (leading me to believe that the virus must have killed)

  (4) so I chose the selection "Command Prompt", which opens by default "X:\Sources >".  I'm in C: and then typed: "sfc/scannow".  The system has responded with the following messages:

  "Start system analysis.  This process will take time. " follow up 30 seconds later by the message:

  "Windows resource protection could not perform the requested operation".

  MAIN QUESTION: any reflection on what other tools and options I try to repair the windows installation / driver set?

  Hello

  I suggest you follow the steps below:

  Method 1:

  Follow the steps in the link and check if the problem persists:

  http://support.Microsoft.com/kb/958233

  Method 2:

  Connect over winre and rename the driver files that he talked with *.old quick order. You can find these % system32%. Follow these steps:

  a. use the Windows 7 DVD to start the computer from Windows Recovery (WinRE).

  b. in WinRE, open a command prompt. To do this, follow these steps:

  On the screen to install Windows, select the appropriate language to install, time and

  currency format and keyboard or input method options and then click Next.

  c. click on repair your computer.

  d. click 7 installation you want to repair, and then click Next.

  e. click on command prompt.

  f. navigate to % system32% and rename old files 8.

  Method 3:

  After step above the computer restarts. Run the System File Checker tool to troubleshoot missing or corrupted system files. Follow the steps from the link:

  http://support.Microsoft.com/kb/929833

• Startup Repair does not work it starts when it wants... .and when it does not I must start up for hours before his sucsessfull...

  Signature of the problem:

  Problem event name: BlueScreen

  The system version: 6.0.6002.2.2.0.768.3

  Locale ID: 1033

  More information about the problem:

  BCCode:                                               a

  BCP1: 000000000000002A

  BCP2: 000000000000000C

  BCP3: 0000000000000000

  BCP4: FFFFF80001EB5D17

  OS version: 6_0_6002

  Service Pack: 2_0

  Product:                                               768_1

  Files helping to describe the problem:

  C:\Windows\Minidump\Mini012210-02.dmp

  C:\Users\Deb\AppData\Local\Temp\WER-100698-0.SysData.XML

  C:\Users\Deb\AppData\Local\Temp\WER9F0C.tmp.version.txt

  Hello

  Added new hardware, updated drivers to date (don't forget to check in Control Panel - Windows Updates - pilot
  updates), or add key software lately? Pilots and security/antivirus/antispyware products are also likely
  suspects. Next message is my generic driver updated methods to use when you get to this section of the
  troubleshooter.

  BCCode: a 0x0000000A

  Cause

  This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.

  The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.

  If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.

  Solve the problem

  If a kernel debugger is available, get a stack trace.

  To resolve an error caused by the faulty device driver or service system, BIOS

  1. Restart your computer.
  2. Press F8 to character-based menu that displays the choice of operating system.
  3. In the Windows Advanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.

  To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool

  1. Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
  2. Try disabling the cache in memory of the BIOS.
  3. Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
  4. Make sure that the latest Service Pack is installed.
  5. If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
  6. For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.

  If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.

  =========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  It is my generic troubleshooting tool and can probably give more specific help when you give the ICC codes.

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
  information on all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Windows vista Startup Repair will not stop running

  Hi hope someone can help

  When I boot computer it goes to startup repair and custom automatically stops running same thing that happens when I use safe mode. Recently, we used the system restore, it worked fine until we used the Startup Repair
  Thanks for any help you can give

  Hi, Gretaevan2,

  Thank you for visiting the Microsoft Vista answers Forum!

  * If this happens even in safe mode, then it is possible that the hard drive is the source of the problem.

  You can try the following steps:

  STEP 1: Try to perform the disk check and see if there are errors.

  See the following knowledge base to perform the disk check: http://support.microsoft.com/kb/315265

  STEP 2: Try the SFC Scan now.

  See the following knowledge base to run SFC Scannow: http://support.microsoft.com/kb/310747

  If, in case, the step above does not help, try to perform the system restore to an earlier date when everything was working well.

  We can't wait to hear back on your part.

  Best regards, Vishal B. Microsoft Support Engineer answers visit our Microsoft answers feedback Forum and let us know what you think.

• Satellite A300 - startup repair does not work

  When I went to use the Startup Repair option in the advanced boot options at startup that he told me that the application cannot run and shut down the computer.

  I have a laptop Satellite A300-1OM.

  As far as I know, this option has nothing to do with Toshiba and this is the Microsoft function.

  What is the problem with your A300?

• The keyboard on the Windows Media Center screen does not appear when I hit the enter keyboard key!

  I searched through the internet trying to find a solution to this annoying problem: after change to enter the registry and the application of the value entered for showOskOnKeyboardEnter under MCE. PerUserSettings, I always have problems serious on-screen keyboard to appear by using the key "Enter" on the keyboard.  I managed only a couple of times to get the OSK to appear among the dozens of attempts, however, I am unable to recreate the actions - is absolutely not stable.  The only area that reacts to the 'Enter' key is looking for music.  All the fields in the section of Netflix and movies search fields are unresponsive.  Not even works tap triple function.  The only compatible and possible way to have the OSK appear is to double click on the field - that does not work given that the goal is to have an IR remote with the Media Center application interface.  The button 'OK' on the remote control is mapped to the Enter key (except if WMC has a key code value for the 'OK' button).  Help, please!

  I had this problem and it was very frustrating.  The posted solution did not work for me initially.  What I've discovered, is that you have closed Media center before editing the registry.  If you change it while it is open it does not pick up the change and then save settings (i.e. with showOskOnKeyboardEnter = 0) when you close.

  Then...
  1 close Media Center.
  2. follow the steps of the posted solution: http://mymce.wordpress.com/2011/04/20/on-screen-keyboard-in-windows-media-center-doesn ' t - appear /
  3. Open Media Center.
  Should work now.

• Content of Word files and Excel does not display when I open them on a reader shared, VPN

  Have Windows 7 Home Edition.  I have a working VPN connection where I can see the files that are shared it but I can't open any word or it excel files.  My Word and Excel works other places to open the files I saved.  Thank you!

  Talk to your personal COMPUTER.  It seems to me that there is a problem of permission on the share or in the VPN tunnel. Brian Tillman [MVP-Outlook]