Satellite A300 - startup repair does not work

When I went to use the Startup Repair option in the advanced boot options at startup that he told me that the application cannot run and shut down the computer.

I have a laptop Satellite A300-1OM.

As far as I know, this option has nothing to do with Toshiba and this is the Microsoft function.

What is the problem with your A300?

Tags: Toshiba

Similar Questions

  • during the installation of Vista Service Pack 2, the computor has been disconnected. Now, I don't have an operating system and startup repair does not work. What should I do now?

    Computor was disconnected during the installation of Vista Service Pack 2. I did now no operating system and startup repair does not work. What should I do now?

    You may have to reinstall Vista from the original media or from the recovery partition according to the type of computer you have.

    Hope that you made the backup recommended all of your data before attempting to install Vista SP2.

  • Launch Startup Repair does not work

    Hi, the 'Launch Startup Repair' option does nothing for my installation of Windows 7 64-bit edition.  If I select the screen simply refreshes and presents me with the same two options - Launch Startup Repair and start Windows normally.  It's as if something prevents me to attempt any repair solution.  Anyway, which would cause Launch Startup Repair does not have to work.  Thanks if someone can advise.

    Hi, the 'Launch Startup Repair' option does nothing for my installation of Windows 7 64-bit edition.  If I select the screen simply refreshes and presents me with the same two options - Launch Startup Repair and start Windows normally.  It's as if something prevents me to attempt any repair solution.  Anyway, which would cause the launch startup repair does not work.  Thanks if someone can advise.

    Hello

    It may be damaged.

    If you have problems with the use of the built-in repair software:

    Make your own information system repair disc in this tutorial:

    "How to create a Windows 7 system repair disc"

    http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

    "This will show you how to create a system repair disc Windows 7 to be able to use to start the system recovery options to help recover your Windows 7 installation, if you have not a Windows installation disk, can't find your Windows installation disc or can not access the recovery options provided by your computer manufacturer.

    A system repair disc is not able to install Windows 7.

    Note

    If you are unable to start your Windows 7 to create a Windows 7 system repair disc, and then you could create on another computer for use on your computer. »

    _____________________________________

    Then, use this disk for System Recovery Options:

    "System recovery options".

    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    "How to run a startup repair in Windows 7"

    http://www.SevenForums.com/tutorials/681-startup-repair.html

    See you soon.

  • Satellite A300-1NO - webcam does not work, but the LED lights

    Hello!

    I have a laptop Satellite A300-1NO, with Win 7 installed. My problem is that my webcam does not work always, when I want to use it. Sometimes, it works perfectly in Skype, WLM etc... but sometimes I see a white or a black screen with a 'loading circle' in there. Blue is the LED light, I can see it in Device Manager too, but there is no picture, just 'loading '. I tried to uninstall the driver and then reinstall it, I installed the new "camera Assistant for Toshiba", without success.

    Is there any solution for this?

    > Is there any solution for this?
    I put t think there is solution for this. If I understand you right there is a problem with software pre-installed. It is not easy to say why this is happening.

    I have Satellite A300 too and use it with Win7 32 bit. Webcam works fine all the time.

    One more thing: have you noticed this problem in the first moments after installing Win7 or later?
    Have you installed something that may be the reason for this?

  • Satellite A300-1BZ - microphone does not work - need driver

    My microphone does not work & I can't find what kind it is to locate the pilot, can assits anybosy please?

    Hello

    The internal MIC is part of the webcam.
    Next to the sound driver, you will need to install the Chicony webcam software.

    You could test the microphone using the webcam software there is an option that allows you to record the audio stream

  • Satellite A300 - 1 2 does not work with 3 GB or 4 GB of memory

    Does not work with 3 GB or 4 GB of memory, only 2 GB!
    And if I plug a memory in bank1 2 GB module (bank0 is empty) - it's doesn't work too!

    He arrived with 3 laptops. (Sorry, my English is not good :))

    Have you thought about a fact that the phone doesn't support 3 GB or 4 GB of RAM?
    Isn't it?
    Maybe you should check the manual of the first user that is preinstalled on your laptop.

    I think you would find information very important.

    Equipped laptops Intel Mobile GL960 chipset is supported by the maximum memory capacity of 2 GB.
    As I m not wrong not your laptop was equipped with chipset Intel Mobile GL960 the case must therefore be clear now. or not?

    Also is important to know that you will need to use always first bank/slot memory (bank0) If you use a DEAD memory module!

    Good bye

    I think that you can assign 10 points ;)

  • On Satellite A300-1MX webcam does not work properly

    After my windows Vista system crashed 16 December 2011, I had made recovery.
    After that, I have not found any driver for the webcam on the computer laptop everything. On the Toshiba support page, I finally found the 1.7 version, but this does not at all!

    He always appears: driver Webcam open fails, restart the computer or the camera. Since it's built in camera I tried with the restart of the computer, but which did not help at all. So I tried with the option to repair the driver with Install Shield Wizard. The program has done something, but without success.

    So I uninstalled and reinstalled and it did not help at all!

    Someone has an idea?

    Hello

    Found an article in the knowledge base of Toshiba which describes this error and provides a solution to this problem.
    + Why displays the error message: "Webcam driver open fail. Restart the computer or the camera. » ? +
    + http://aps2.toshiba-tro.de/kb0/OPT84026F0000R01.htm+

    But its related to Portege M600 and Satellite U300 only.
    However, you should also try to perform a BIOS update. After that, set the BIOS to default settings and save the changes. Then try to reinstall the software of webcam once more.

    You should also check the Device Manager. Here in Device Manager that the webcam should be recognized as a USB device, if this isn't the case, then it means that the webcam was not recognized by the OS and that means there could be a hardware problem

    As far as I know, the webcam is connected to the USB controller on the motherboard. If the cable connection is lost, then the webcam is not recognized in Device Manager; or as a USB device or an unknown device.

  • Satellite A300-1MC - recovery does not work

    I have a Satellite A300-1MC. It does not start in windows is right there with the Welcome screen. PC diagnosis indicates that the hard drive is faulty. I replaced the hard drive with a MK3276GSX Toshiba MK3252GSX - both are 320 GB.

    When I insert the recovery disc I get the following message when disk 2 is running "insert the next recovery means that contains the D:\08008XSP6 file. STORMWATER MANAGEMENT.

    Any ideas where I'm going from here? »

    Hello

    Are you sure that you Recovery disk was created correctly?
    This recovery disk function properly in the past?

    You label the discs properly?

    It seems that there is a problem with the recovery disk.

  • Computer turns on but does not boot to Windows, startup repair does not work

    When I turn on my laptop, it brings me to a screen titled "Windows Error Recovery" which means the following:

    "Windows did not start.  A recent hardware or software change might be the cause. »

    He asks me if I want to '(recommended) launch Startup Repair' or 'Start Windows normally'.

    When I select repair system, the screen turns off for half a second only and brings back me to the exact page as I was already on.

    When I select "Start Windows normally", he brings me to the loading screen that usually starts with Vista (anyone who says (c) Microsoft Corporation), except that it never stops loading.  I left for hours, and he was still on the same screen.

    I have a laptop Dell Inspiron 1525 with a processor Intel Core 2 Duo and Windows Vista Basic.

    Follow these steps to try to solve your problems of boot.

     

     

    Restore point:

    Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

    Try a restore of the system once, to choose a Restore Point prior to your problem...

    Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

     

    If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

    Download the ISO on the link provided and make a record of repair time it starts.

    Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

    At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

    When you have changed that, insert the Bootable disk you did in the drive and reboot.

    http://www.bleepingcomputer.com/tutorials/tutorial148.html

    Link above shows what the process looks like and a manual, it load the repair options.

    NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

    Read all the info on the website on how to create and use:

    http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

    ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

    It's a very good Vista startup repair disk.

    You can do a system restart tool, system, etc it restore.

    It is NOT a disc of resettlement.

    And the 32-bit is what normally comes on a computer, unless 64-bit.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    Data recovery:

    1. slave of your hard drive in another computer and read/save your data out there.

    2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

    3 Alternatively, use Knoppix Live CD to recover data:

    http://www.Knopper.NET/Knoppix/index-en.html

    Download/save the file Knoppix Live CD ISO above.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    http://isorecorder.alexfeinman.com/isorecorder.htm

    Download the Vista software from the link above.

    After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

    Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

    Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1st in the boot order.

    Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

    When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

    Click on the icons of hard drive to open and to understand which drive is which.

    Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

    Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    Dell recovery options:

    http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=339949

    Above is Dell to reinstall Vista from the DVD on your computer.

    http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=336966

    And that way if you have a recovery partition on your hard drive.

    See you soon

    Mick Murphy - Microsoft partner

  • Satellite A300 graphics card does not work

    Does not my graphics ati mobility radeon hd 3470, only the blue colour works on it and the display of the laptop is not working too, I need to plug a monitor so that I can work with it? Can I replace it? If so where can I buy a graphics card for?

    Hi paulik123,.

    If you also have a problem with an external monitor, there seems to be a problem with the internal graphics card
    Did you notice the same problem when you get into the BIOS?

    As Akuma writes you can contact a service provider authorized in your country. Guys are able to replace graphic card/motherboard for you.
    The list of aspic, you can find here:
    http://EU.computers.Toshiba-Europe.com > support & downloads > find an ASP.

  • Satellite A300 FN + F5 does not work properly

    Hello
    I have a Satellite A300, PSAGCA-09U01N.

    I would like to connect a coard S-video from my laptop on my TV, and when I press FN + F5, I don't get the icons appear along the top of my screen _anymore_.
    I always get the plug S-video works, but going from normal setting (just laptop screen) by other modes ('laptop screen + TV' etc) is very slow. Can someone please.

    Hello

    Hmm... If the icons don't appear if you press a FN key you must reinstall Toshiba value added package if you use Vista or Windows 7. You can download it on the Toshiba driver download page:
    http://EU.computers.Toshiba-Europe.com

    Value added package controls the FN and enlightenment for example keys in order to check this!

  • Satellite A300 - Chicony webcam does not work after upgrade to windows 7

    I'm frustrated so I came here to see if anyone knows a way to help solve this problem.

    I have a Toshiba Satellite A300, which came with Windows Vista 64 - bit pre-installed. After about a year or two to have the laptop, I decided to upgrade to Windows 7 64 bit. In the process, I believe that the driver of my webcam (Chicony usb 2.0 camera) has been eliminated.

    When I go into the Device Manager in the Control Panel, the webcam is not listed; nor is "imaging devices."

    I tried to download the driver manually, but I get an error message "Webcam open fail." Restart the computer or the camera. »

    My computer has registered my webcam as 'unknown device '.

    If anyone knows how to solve this problem, please, I beg you, let me know.

    > My computer has registered my webcam as 'unknown device '.
    > I tried to download the driver manually, but I get an error message "Webcam open fail." Restart the computer or the camera. »

    This means that the the webcam driver is not installed correctly.
    Visit the page of European driver of Toshiba and install the software/driver webcam just for this model of laptop.

    If the installation fails, restart the laptop and the tent.
    This should solve the problem.

  • Satellite A300-V01 - webcam does not work with msn

    Hi all

    I was wondering if there was someone out there who could help me...

    I recently bought an A300/V01 and try to use the web camm for it, but whenever I open it on his own (not with msn or any other program), it freezes and will not work, and when I try to send my web cam on msn it tells me that there is no connected webcam.
    I'm pretty computer illiterate so iv tried to fix it myself but sadly failed.

    so, if there is someone out there who knows how to fix it would be great if you could help...

    Thanks xoxo

    Go to the Toshiba website and to update the camera/Webcam driver.

    Also try closing/leave the camera software help.

    You should also install Vista Service Pack 1 (SP1), if it is not installed.

    And to ensure that upgrade to the latest version of MSN Messenger.

  • Satellite A300 - Wi - Fi does not work and cannot connect to networks

    I've had my laptop for 3 months. The wi fi and internet worked but I tried to use the cable home for the internet lan and wifi at the University, but it does not connect.
    I'm sure that I have not dropped the lap top. I took the laptop to check at a friends for wifi and without success.

    It's maybe something broken inside? Because I tried to connect to the network via a cable, but it does not find when it is supposed to.

    Please help :)

    > Wi fi and internet worked but I tried to use the cable home for the internet lan and wifi at the University, but it does not connect.
    > Because I tried to connect to the network via a cable, but it does not find when it is supposed to.
    Stand by. You only have this problem of connectivity with WIFI (wireless) or with LAN (cable) too?

  • Startup Repair does not work it starts when it wants... .and when it does not I must start up for hours before his sucsessfull...

    Signature of the problem:

    Problem event name: BlueScreen

    The system version: 6.0.6002.2.2.0.768.3

    Locale ID: 1033

    More information about the problem:

    BCCode:                                               a

    BCP1: 000000000000002A

    BCP2: 000000000000000C

    BCP3: 0000000000000000

    BCP4: FFFFF80001EB5D17

    OS version: 6_0_6002

    Service Pack: 2_0

    Product:                                               768_1

    Files helping to describe the problem:

    C:\Windows\Minidump\Mini012210-02.dmp

    C:\Users\Deb\AppData\Local\Temp\WER-100698-0.SysData.XML

    C:\Users\Deb\AppData\Local\Temp\WER9F0C.tmp.version.txt

    Hello

    Added new hardware, updated drivers to date (don't forget to check in Control Panel - Windows Updates - pilot
    updates), or add key software lately? Pilots and security/antivirus/antispyware products are also likely
    suspects. Next message is my generic driver updated methods to use when you get to this section of the
    troubleshooter.

    BCCode: a 0x0000000A

    Cause

    This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.

    The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.

    If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.

    Solve the problem

    If a kernel debugger is available, get a stack trace.

    To resolve an error caused by the faulty device driver or service system, BIOS

    1. Restart your computer.
    2. Press F8 to character-based menu that displays the choice of operating system.
    3. In the Windows Advanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.

    To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool

    1. Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
    2. Try disabling the cache in memory of the BIOS.
    3. Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
    4. Make sure that the latest Service Pack is installed.
    5. If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
    6. For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.

    If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.

    =========================================

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------

    Also this, so you can see the probable bluescreens.

    Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
    http://www.winvistatips.com/disable-automatic-restart-T84.html

    -------------------------------------------------------------------------

    It is my generic troubleshooting tool and can probably give more specific help when you give the ICC codes.

    Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
    Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
    codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
    information on all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

    You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
    system installed by the manufacturer.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    You can try a system restore to a point before the problem started when one exists.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    -------------------------------------------------------------------------

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
    smile, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting, STOP error blue screen Vista
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    The Options or Vista recovery disk Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

Maybe you are looking for