Crackling on Satellite C870-198
I just got a new Satellite C870-198 and the audio began to Crackle after about a week.
It seems to happen with external speakers, headphones as well as with the speakers on Board (i.e. all the time). Windows 8 has been frustrating me anyway so I installed windows 7 on it, but the problem is still there.
The cracks are more noticeable when the music I play is stronger. I tried to uninstall the sound drivers to try a few different, but they always reinstall themselves whenever I restart. I don't really know what I'm doing. Sometimes it makes a brief gurgling like electronic interference noise or something too.
To be honest I'm not very well if the issue you described is really a problem of laptop because you said that you've probably noticed the sound of crackling playing loud music of m.
From my point of view, it could be a common behavior in which crisscross loud music.
You are using Windows 7 now.
On the page of the Toshiba UE (Satellite C870 PSCBAE) driver, you can find the audio drivers 3.
Realtek, nVidia, SRS
All drivers must be installed.
In addition, you can find edge settings in Control Panel-> Realtek HD Audio Manager.
Here, you can change the sound properties. Check it out.
I have a Satellite C650-198 running Windows 7 (64-bit) and notice that the size of the 250 GB drive is divided into two main readers of 116 GB each (I accept that the remaining 18 GB is the section of system recovery and have no problem there).
I reinstalled Windows 7 from the recovery on DVD media and would like to know if it's something I did which puts in place the two discs or is it quite normal and intentional?
When you use recovery DVD for the installation of the OS the procedure is always the same:
-the whole HARD disc will be deleted
-existing partition deleted
-HARD disk will be formatted
-two new partitions will be created
-recovery copied image
-Operating system installed
This will happen again and again every time that you use the recovery DVDs.
I lost my software Satellite C870-196 (read dvd nero12, etc.).
Can I find or download somewhere?
I do not have a folder on my sheets containing the software.
+ The message has changed: the content has been translated.
Instant Messaging user a new SATELLITE C870-1JV
Or seen a review on an American site saying that all software pre-installed Toshiba slowing down the operating system.
The site has recommended that a windows clean install to remove all...
Everyone does this, or would you recommend?
Anyone like the software installed and recommend keep it?
> Someone has he done this, or would you recommend?
You always want to use the advanced features like function keys laptop?
If so, don t remove the feature key Toshiba software that controls the keys.
You always want to be informed of updates to the driver through Toshiba Tempro or Toshiba Service Station?
Then don t delete these software
But as far as I know there are also other additional software installed on the laptop.
For example: TOSHIBA, TOSHIBA Eco Utility, TOSHIBA PC Health Monitor, etc.
All of these tools provide additional functionality, it s your decision whether or not you want to use.
I am a new user of SATELLITE C870-1JV...
It comes with 6 GB of ram... (4 + 2)
Can I replace the 2 GB with 8 GB for a total of 10 GB?
I noticed he can spend to 16 GB total so would like to eventually
Specification of Satellite C870-1JV page shows that you can upgrade the memory up to 8 GB of RAM.
This means that you can use only 2 x 4 GB DDR3 1333 MHz(PC3-10600) modules
I have a problem with my toshiba satellite C870. The noise stopped working. the sound icon is cut and I got a message: no speakers or headset is connected. I tried corrections but I thought that my driver is up to date. For accuracy I am under W7. Sorry if my English is bad (I speak french, but you can answer me in English)
Panel of-> sound-> the Read tab
You see your speakers or headphones here?
If so, make sure that the speakers are marked as the default device.
In addition the combination FN + F11 would turn on and off MUTE.
When two solutions of workaround don t help, uninstall the device high definition audio / controller as well as the audio driver from the Device Manager and restart the computer laptop n.
After restarting again the system should install the uninstalled drivers even more often, this will help you to get the sound.
I am (was to) buy a Toshiba Satellite C870 - 1 H 2 (from amazon.co.uk).
The specifications look ideal for me, but at the last moment, I thought to check if VT - x extensions are supported.
I know that the processor supports extensions (as detailed here: [http://ark.intel.com/products/71465/]), but I know also that the extensions are often not enabled (or there is no option in the BIOS to enable them).
The expression "Virtualization Technology" (which is present on other pages of the specification) is clearly absent from the plug laptop here: [http://www.toshiba.co.uk/discontinued-products/satellite-c870-1h2/].
I saw some comments that suggest the Satellite * Pro * series usually provides the support for virtualization, but it always seems to be missing on many current models of Pro's specifications.
I don't know why the C870 would not support VT - x, when we know that his material, but the specifications indicate that this is the case. On the other hand, I found no references to people complaining about the lack of VT - x support.
So my question is, the Satellite C870 - 1 H 2 actually does support VT - x, or not?
(and if not, because it takes just a very small piece of code BIOS, why not?)
> The same issue applies. These models are supported virtualization
VT support is always depends on the CPU built in Notepad. But you mentioned it in the first post.
According to the page of the Ark from Intel, the Intel Pentium 2020 M processor supports Intel Virtualization Technology (VT - x)
First of all, thanks for reading and eventually respond to this message
I installed opensuse 12.3 x86_64 on a Toshiba Satellite C870 - 1 HR with a wifi/bluetooth adapter realtek 8723. The rtl8723ae module is running.
Wifi works with kernel 3.10 provided by opensuse kernel team, but not the BT. bt kernel modules are loaded, kde recognizes the bt stack, but not access.
0: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
However, I have discovered with dmesg:
8.347377: HCI device and connection manager Bluetooth Initialise
8.347389 Bluetooth: socket initialized HCI layer
8.347391 Bluetooth: L2CAP initialized SSL
[Bluetooth 8.347399: initialized SCO socket layer]
8.350732 ACPI WARNING: 0 x 0000000000004040-0x000000000000405f SystemIO comes into conflict with the \_SB_ region. PCI0. SBUS. SMBI 1 (20130328/utaddress-251)
8.350739] ACPI: If an ACPI driver is available for this device, you must use it instead of the native driver
8.356121] usbcore: registered new interface driver btusb
rtl8723ae 8.759901: using the rtlwifi/rtl8723fw_B.bin firmware
8.875659 ACPI WARNING: 0 x 0000000000000428-0x000000000000042f SystemIO comes into conflict with the \PMIO region 1 (20130328/utaddress-251)
8.875666 ACPI: If an ACPI driver is available for this device, you must use it instead of the native driver
8.875670 ACPI WARNING: 0 x 0000000000000530-0x000000000000053f SystemIO comes into conflict with the \GPIO region 1 (20130328/utaddress-251)
8.875674 ACPI WARNING: 0 x 0000000000000530-0x000000000000053f SystemIO comes into conflict with the \GPXX region 2 (20130328/utaddress-251)
8.875677 ACPI: If an ACPI driver is available for this device, you must use it instead of the native driver
8.875679 ACPI WARNING: 0 x 0000000000000500-0x000000000000052f SystemIO comes into conflict with the \GPIO region 1 (20130328/utaddress-251)
8.875681 ACPI WARNING: 0 x 0000000000000500-0x000000000000052f SystemIO comes into conflict with the \GPXX region 2 (20130328/utaddress-251)
8.875684 ACPI: If an ACPI driver is available for this device, you must use it instead of the native driver
lpc_ich 8.875686: resource found on gpio_ich
8.888936 ieee80211 phy0: rate control algorithm selected "rtl_rc".
rtlwifi 8.889107: wireless switch is on
Your problem is a little weird!
Your wireless network card is a BT / WLAN combo and should be supported by the kernel used in openSuse 12.3.
Check the functionality in Windows or any other end Linux distribution?
I would say to download Fedora 19 and run as a direct medium OS to check the operation of BT.
If it works fine, I belive there is a bug in the distro openSuse.
If this isn't the case, I really think you should consider checking your hardware.
I have the same card in my works C850 and BT just perfect in Fedora 19.
Hope this helps you out
So, my sister has Satellite C870-1EX and she uses new Audio Mixer with integrated sound card sends its via USB cable to the computer (computer recognises as external audio device and map). It's the device: http://alesis.com/multimix8usbfx.
A few weeks ago, she began to notice a very odd sound, sort of high-pitched, whistling, like a very fast electronic beep. Something similar to what good old modems of the internet when they were connected to the phone line, just not a little faster and strong.
First of all, of course, we tested every single setting on the Audio Mixer Panel.
Then, we got new USB cable and it traded.
After that we also took down all the material, checked all cables, if necessary, detangle swapped the power supply, check a different recording software, even tried a few other recording devices USB etc etc.
None of this has helped. The drivers are all there too.
Here's the catch. I used the same equipment with the same settings on my computer and no hissing noise at all. The thing is, any parameter, we tried, only the hiss remains the same, nothing changes.
Even if you apply a few sound effects which should either accentuate or reduce any type of noise in the signal that is sent to the USB port on the computer, this whistling noise remains the same.
What worries me is that something is wrong with the material of my sister's laptop.
The noise does not appear if we use, for example, microphone that uses 3, 5mm taken or the built-in microphone of the laptop during the recording of the commands in the same session with the same software and similar settings (given some must be different because of the different entry).
However, the noise is if we use an external USB recording equipment on any of its ports.
Windows on his laptop were resettled some time ago (now it is on Windows 7), but the problem appeared a few weeks later.
As I said earlier, the drivers are all there and to date as well.
So, I hope that one of you will return with a software sollution (single)... and I hope we will not need to take his computer back to the shop.
However, as it seems now, the last is more likely to occur.
Please, tell me I'm wrong :)
One of my friends had a similar problem with a DJ controller: Traktor Kontrol S4
There was not a sound, but he noticed a few dropouts stuttering and audio.
The problem was the background processes that were open when you use the controller.
To resolve this problem, it was necessary to disable all possible devices in the device as WLan, LAN, Bluetooth Manager, etc.
In addition, he had to Disable Antivirus software and firewall that was running in the background.
I put t know if it helps you, but I think that its worth a try
Another idea: try to reduce the performance of the processor. This is possible in the Windows 7 power management.
How to manage Windows 7 power management features
Option CPU power management contains the option called the Maximum processor state
Here you can set it to 90% - 80%
I recently bought a new toshiba laptop.
I noticed that the AMD drivers are not supported directly and I need to download from here.
They do not seem to do the trick and I've always found these rather confusing support sites.
If my laptop is Toshiba satellite C870-1GD (pscbce-03c004bt)
([Link 1 | http://www.toshiba.be/nl/laptops/satellite/c870/satellite-c870-1gd/]: Dutch)
The Belgian driver for my mobile site gives these 2 drivers
Intel: [link: http://www.toshiba.be/innovation/download_driver_details.jsp?LNG=10&service=BE&selC fulltext = 2 & selFamily = 2 & selSeries = 312 & selProduct = 747 3 & selShortMod = 3766 & language = 12 & selOS = 40 & selType = 11 & yearupload = & monthupload = & dayupload = & useDate = null & mode = allMachines & search = & action = search & macId = & coun try = 3 & selectedLanguage = 12 & type = 11 & page = 1 & ID = 88053 DISO = 40 & driverLanguage = 42]
AMD: [link: http://www.toshiba.be/innovation/download_driver_details.jsp?LNG=10&service=BE&selC fulltext = 2 & selFamily = 2 & selSeries = 312 & selProduct = 747 3 & selShortMod = 3766 & language = 12 & selOS = 40 & selType = 11 & yearupload = & monthupload = & dayupload = & useDate = null & mode = allMachines & search = & action = search & macId = & coun try = 3 & selectedLanguage = 12 & type = 11 & page = 1 & ID = 88048 DISO = 40 & driverLanguage = 42]
I downloaded both and featured intel should be on board. However, it does not change a thing.
So far, I've tested League of legends; works without problem (no update necessary driver)
But it does not even minecraft cause of no openGL acceleration. Which in my opinion is very weird
In your case the situation is quite clear. Your model of laptop has AMD Radeo HD 7610 M GPU inside and last supported driver is always offered on the Toshiba download page. If you have this latest version that s it.
In any case, in the past, several people spoke of trouble with Minecraft. Put Minecraft as a search term in this forum and you will find several interesting discussions. One of them that you can read on http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=282293
Update all the windows are properly except for the 64-bit processor that gives me a different error all the time.
I can't do despite the different means of redress available and I have to turn it off.
Why these mistakes for which I can't find solutions?
To be honest, I don't know what you're talking about.
What error do you mean exactly?
Satellite C870-196 laptop computer supports the processor Intel Celeron B830
Here is the page Intel Ark providing details of the CPU:
The processor supports 64-bit instructions so the processor is supported by orders for 64-bit and the instructions that a microprocessor understands and can carry out.
Preinstalled system was Windows 8 64-bit so I n t see a serious reason why mistakes regarding the CPU should appear.
I would like to know if it is possible to remove the upper part of a key on a TOSHIBA Satellite C870 C196 to clean underneath?
I have a button that does not work properly.
How to go without anything break?
Is there a specific tutorial for this projection keyboard how?
Thanks to you all.
Tutorial so that it does not exist, but I can say, is that you can remove the plastic cap. It may be problematic to implement.
On older machines, it was quite easy, but on the new laptops equipped with flat keys, it is not so easy. As far as I know that each CAP is fixed with 4 pretty small hat holders must be fixed properly. to put all the 4 instead is not so easy.
I don't know what to say. You can try it, but on the other hand, I don't want to encourage that because you can damage something and in the end, you need to replace the entire keyboard.
If there is a serious problem, you can request the service of Toshiba for advice and ask for help.
Hi, I hope I'm posting in the category right forum then...
My laptop is Toshiba Satellite C870-190 and it doesn t want to start my windows 7 CD.
I tried first with the DEL-button that opened the system startup when I start Notepad and then choose the CD-ROM device and do not want to load the CD and then I chose F2, the first unit on the boot to the CD-ROM section, still do not want to load it... the final solution, I tried to install it from the Windows 8 (current operating system) from my computer--> CD--> setup.exe, and then click INSTALL.
My computer laptop doesn t have allowed me to install it even from Windows... on file copy screen to say... and then it gives me an error that says that the operation failed... What is happening with this laptop?
How can I format my HARD drive and then install windows 7?
At the beginning I will say that I hope that you have created a recovery media (DVD or USB) before you have begun to install Win7.
Return to your Win7 installation. A long time ago I installed Win7 on friends U940 and the first stage was changing course startup in the BIOS settings mode - http://aps2.toshiba-tro.de/kb0/TSB2C03F80002R01.htm
After the installation Win7 has started successfully, but in my case the SATA driver support was necessary.
Please check first and send comments.
I would like to put a password only to access or modify the BIOS and not to launch the system on my TOSHIBA Satellite C870-196.
But I do not understand that is configured in the BIOS:
-Set Admin password
-Set user password
Here are some tips as the basis for a better understanding
Check it please and if you have any other questions do not hesitate.
I just bought my Satellite C870-12F and I noticed the only work of function keys (F1, F2 etc) when you use the Fn key, I was wondering if I can 'swap' them, while I have to press Fn first and then to increase brightness, for example.
I'm used to having the keys of F or primary, without an extra key to activate.
As far as I know, you cannot change anything.
Keys Flash cards (Fx) can be used in combination with the FN key only.
Maybe you are looking for
I have an iPhone 5 c running iOS 9.3.5. Try to add music, but when I try to open the music player, I get an advertisement for the apple's music and the screen freezes. I can't access the actual music files (transferred from my PC via iTunes). I can s
I am trying to locate my Outbox in local folders, so I can delete unsent messages. But everything I have nothing characteristics into account and advance. No idea how to find?
With the help of windows 8Really want to get rid of the unsent messages and know that I must locate the shipping box to do this. But this isn't in such local issues suggested by the forums. Thanks for your help.
Hello Where can I find the driver (Setup information .inf file) to the hard drive of my computer Satellite U400 PSU40 - 01 M 001 hard drive is MK3252GSX.I need this file to make a recovery of the computer system. Windows Vista 32 bit. Thank you b
My HP Photosmart c7250 will not answer incoming fax. I put it to 2 rings, but I always have to be there to press auto-answer to receive faxes. Please help I need to receive faxes when I'm not by printer
Message when I try to use the ipconfig/release command line, it is that "no operation can be performed on wireless network while it has its media disconnected." What does that mean?