DAQmx Read 1 d vs 2D DBL WFM

Similar Questions

• Why DAQmx read 200714 error when you save the file?

  In particular vi that I created, I have 3 analog inputs coming in and are graphically represented.  If I choose to save the information to a file, a dialog box appears and I can choose what to save it under.  If I take too long to save the file (aka about 8-10 seconds if the sample read rate is 500/s) then I get this error once the file has been saved:

  Error-200714 occurred at .vi DAQmx Read (analog 1-d NChan DBL 1Samp)
  Possible reasons:
  Acquisition stopped because the driver could not transfer the data from the device to the computer's memory rather quickly. This was due to limitations of the computer system.
  Reduce your sample clock rate, the number of channels in the task, or the number of programs on your computer that is running simultaneously.

  Why the DAQmx bed vi I have this problem when the vi has been idle for 10 seconds then I choose where to save the file?  How can I fix this error?

  Hi child of pre-school age,

  I think your error might be caused by the read buffer overflow. my suggestions for you would be to either the following four ideas:

  1. stop the acquisition before writing the file. This should mean that the DAQmx Read function will no longer be reading and therefore does not generate an error.

  2. If you still want to read the data but also write data as well, I think you'd be best suited for use live TDMS. TDMS allows the user to stream to a reading of filewhilst.

  3. the configuration backup dialog box file before starting the acquisition. Download the user to enter all data in the file before you start to acquire.

  4. change the buffer to unlimited so that you have enough time to navigate the record window.

  If you send your VI I can advise others

  Let me know how you go,

• How to bothAnalog DBL and Analog 2D 1 d DAQmx read.vi wfm

  Hello

  I use Labview2010 and NIUSB6009 for aquairing data. I need to have two Analog1D waveforms and

  Analog DBl DAQmx Read.vi 2D. I do continuous sampling.

  no idea how to get both types of DAQmx Read.vi?

  Thank you

  If you get the data from one channel at a time, then you will probably get table 1 d of waveform. If you want to acquire data from multiple channels at the same time then you should get 2D table contains all the information channels.

  If I'm right, you can't get both types of data (1 d and 2D) DAQmx playback function. I did not hear that. That's all what I can expect.

• How .vi DAQmx Read (analog 2D NChan DBL NSamp) to acquire continuous data?

  I try to get the .vi DAQmx Read (analog 2D NChan DBL NSamp) to acquire data continuously.  The 'help' indicates I need to wire the number of samples per channel-1, but it doesn't seem to work for my application.  If I have the wiring to any number greater than 0, the data collection works, but is not continuous.  I enclose the code (Sept15_MainPanel_WorkingBaselines_ApplyBaselines and Calibration.vi) and a Subvi (Collect_Baselines.vi) if someone wants to take a look.

  Here's what I'm trying to do:

  I use a unit NI USB-6009 to collect analog voltages of load cells 2 (channel 0 and channel 1) and 2 displacement transducers (channel 2 and 3).  The main panel of the VI contains a listbox with 4 options - 'Check EMG channel', "Collect base lines," "Collect Data" and "end of program".  'Collect base lines' 'End of program' work and I'm working on writing code to "Collect data".

  For the option "Basic collection", 2500 samples are read from 4 channels described above and 2500 samples are averaged.  This works.

  The option "Data collection" - I would like to that data from 4 channels to acquire permanently.  Finally, for the option of data collection, data acquisition stops when channel 0 detects the force of 200 N - so I will not always have a finite number of samples read.  The time it takes to reach the value of this force will be different for each test.

  -How can I get continuous samples for my 4 channel?  Is .vi DAQmx Read (analog 2D NChan DBL NSamp) function badly and if yes, what should I use?

  Thanks in advance for any ideas or advice.

  Esther

  First, in case 1, you need not the structure of flat sequence.  The son of the error and data properly will dictate the flow of execution.  Then, in State 2, you must initialize the shift register, unless you want to keep the data is accumulated each time that you run the vi.  The reason why you don't see all the data here is because you have - 1 wired for the number of samples per input channel.  You must connect a number here, even if you are taking continuous samples.  The service needs to know how much sample to gather at one time.  If you put-1 here, the number of samples per channel must be set up in the synchronization function DAQmx (sample clock).  If you specify a number here, then you put-1 in playback function.  The DAQ hardware will read continuously, you must retrieve the data from time to time, so you must specify the number of samples.  By reading inside a loop, it will continue to read until the stop function is encountered.  I guess that the Clear function acts as a stop.  But you must always indicate playback vi how many samples to read and return on each iteration of the loop.

  The documentation is a little misleading.  He warns that a - 1 will cause a continuous reading.  But the pads are so big, he can not read continuously forever without losing data.  If you specify a finite number, playback in a loop, and he will read this number and return the data (empty the internal buffer) at each iteration of the loop.  Continuous means that you just call the start function once.  He will read at each iteration of the loop until the stop function (or clear) is called.

  Here is the difference between the setting of the Timing DAQmx function for continuous or finished reading: finite samples requires a tenure, he reads the finite number of samples, and it's done.  It requires another start to read more data.  Continues to read requires only a start.  It still reads a finite number of samples, but when this is done, you can retrieve the data by calling the read function until he could continue.  After the reading, you don't have to call for new start.  Look at it this way.  Start is what starts the collection of data, not the read function.  Just read empty buffers in your data feed.  The data acquisition continues in continuous mode, but you must call read again to get the data on the pads.  If you specify basically buffer size when you set the number of samples per channel.

• Get error-200088 DAQmx reading (Analog DBL 1Chan 1Samp) .vi < add >...

  Hello

  I am using examples of labview and Labview 2011, I use the a sample.vi acq for the value of the voltage reading.

  but the thing is that I get the error of block then read this DAQmx Read (Analog DBL 1Chan 1Samp) .vi - 200088 ... And it's not indicate the correct voltage in labview.

  I also connected Multi meter with the analog card reader and multi meter gives the correct value, but it is not possible to achieve with labview.

  Please guide me how can I solve this problem which could be the reason for this.

  Thank you very much.

  
  

• What is READ the array returned by the DAQmx meter? How can I know the two functions DAQmx READ data stream in the same WHILE loop?

  I have a question about the order of execution.  In the WHILE loop, I have two things to measure, period and tension using the DAQmx READ functions for voltage and the meter.  In the end, I want to collect these data as points almost simultaneously as possible, as a pair and then send them together to another piece of code (not shown here) which them will result in some sort of command for an engine.  It would be run, and then I want to perceive the tension and the period at a time later and do the same thing.

  (1.) I'm a little confused on what the meter of the READ function is back because it's a table.  What is a picture of?  I thought that it was up to the value of the individual periods between rising edges.  The output of the counter 1 DBL d's a table. How many elements in this table, and what determines the size of this table?  Are the elements of the array the individual delays between the edges?  How many values are stored in the array by executing?   We take the AVERAGE of the last 15 items, but do not know if we are throwing some of the data or what.  How to understand the composition of this painting?  How can I change the composition of this painting?  Is it possible to measure only one period at a time, for example the time between TWO edges?

  2.) Will this WHILE loop execute as it gathers tension and a "period table ' (remains to be understood by me) by TIME running in a loop?  In particular, we want that the value of the tension associated with the value of the AVERAGE of the period "array", so we can use two data items to create orders of next control every time that the two values are reported.  The structure for the delivery of vi will be attached data in pairs like this?  I understand that one of the READING functions run not before the other function of READING in the WHILE loop.  I want that the period "means" and "strain (Volt) collected at the same pace. This vi will he?

  Thank you

  Dave

  Hi David,

  I suggest including the DAQmx Start Task function. If it does not start before the loop, it starts the loop and work very well, but it is not as fast and efficient. In the model of task status, task wiill go to run the checked each iteration of the loop and then back the time checked running when it restarts.

  The status of the task model: http://zone.ni.com/reference/en-XX/help/370466V-01/mxcncpts/taskstatemodel/

  Kind regards

  Jason D

  Technical sales engineer

  National Instruments

• DAQmx Read is limited to 9 digital channels?

  I'm reading several digital channels with DAQmx Read (Digital 1-d Wfm NChan NSamp). The output of the DAQmx Read vi is a table 1 d of digital waveforms. If I put this output through Cluster in the cluster that results seems to be limited to 9 elements, data [0] through data [8]. DAQmx Read output is limited to 9 digital waveforms? I'm using Labview 2009.

  No, this is not done, is choosing the Cluster size. Nine is the default value. Right-click on it to change.

  Because you have to change it every time you change the number of channels, are you sure want to use clusters instead of just working with a table?

• DAQmx read slowly measurement

  I am still fairly new to LabView, only it uses about 5 months, so bear with me.

  I'm trying to understand why the DAQmx playback function runs slower I expect.  I use a PCIe-6363 map connected to two BNC-2110 connector blocks.  I run the attached code (Position AOM control_prod_cons) and producer while the loop takes about 14 ms to execute.  Here's why this is a question:

  The Subvi belongs to a larger structure that we use in our research lab to run our system of construction craft nanofabrication.  You are using a computer-controlled turntable (wise move task), monitors of reading of the scene (spot monitor sensor) sensor and control a shutter that controls power to the sample (Subvi with lightning) laser.  Up to 4 outputs analog and three analog inputs.  The scene is being ordered to move in 5 steps of nanometer to a speed of 50 micrometers per second, a rate of analog output of 10,000 samples per second per channel (3 of them).  The shutter has a rate much more low yield, at most 5 samples per second.  Our goal is to synchronize the movement of the scene with the shutter, and so we must read the exact position of the scene using the analog inputs, one for each axis, x, y and z, vote as often as possible, even if in reality it didn't need to be more than one read each ms.

  AOM control_prod_cons position takes two points in space that we wish to move between two points where the shutter must open/close.  The first image in the flat sequence did some vector calculations to get the line that we write out the origin of the octant where x, y and z be positive by adding or subtracting, then making reflections around axes, if necessary.  The end of x, y and z values (which are now all positive) are summed and placed later in the sequence.  Coordinated sensor monitor are then read in (loop producer) and turn the same way coordinates the target have been transformed (consumer loop), then compared with the values of (x + y + z) end and start (0) and adjusted accordingly shutter. (For troubleshooting purposes, "off" is 2.5 and read the text file we entered to extract structure).

  All the tests I've done so now tell me that the loop of the producer is the rate limiting step.  For a line that is 30 microns long, with the displacement of scene I described above, I was 45 or 46 readings, that works on a read (on the three channels) once all the ~ 14 ms, or only 72 samples per second per channel, which is * very * slow for the card and is not acceptable for our application.  Am I missing something?  Why the producer loop takes 14 ms per iteration?  I tried to reduce the sampling frequency of writing to 1000 samples per second per channel, but that did not alter the reading rate, so I'm not sure I can cela pins on the map.

  I ran the DAQmx read function as a NChannel 1sample, read in a while loop like I do in more complicated VI, reading of the three analog inputs in a very simple VI who only reads the sensor monitors and nothing else and the reading rate was 2750 samples per channel (read 5000 samples through three channels in 1800 ms) , so I know that the card can read that fast.

  I've also attached the highest lying VI that sets up the physical channels for adding information.  I am also attaching a VI where the producer/consumer framework is not used.  Also, this while loop took ~ 14 ms to exploit.

  Sorry, that was so verbose, just try to do what I'm trying to erase.  If you have any other questions, please just ask.  Thanks in advance for your help.

  Well I'll be darn.  The "task AO is?" query seems to be the culprit.  I have no memory of being always aware that there was such an expensive application.  I don't know if I tried to make such a request in a tight loop before, but I'm a little surprised by the fact that I'm surprised.  I don't know if anything is changed, but in case it's a secondary-ish effect, I use the new DAQmx 16.0

  Another approach would be to use a property DAQmx writing node to query the Total number of the samples.  It seems quite a bit faster.

  -Kevin P

• DAQmx Read simultaneous calls on the same digital line

  Hi all

  I use v10.0 LV 32-bit on Windows 7.

  I use DAQmx Read (in a task) to check the value of a digital line. Is it OK to do this in two different locations in a program at the same time for the same digital line? Or I have to put a wrapper around reading to force operations to be sequential?

  Thank you
  Zola

  When you need to expose the capabilities of resources to multiple areas within a project (expand the scope of a resource) it is common to wrap the resource in an Action engine to encapsulate the resource functions. See here for an example of a 'Module on resources' material and a discussion animated about how this code help development construction and avoid resource conflicts.  If you have not read famous nugget again – he of Ben is a link in my tag "Required_Reading".

  Or more directly.  Yes, you should encapsulate these readings DAQ to avoid suspended

• Error 200088 using the DAQmx reading VI in a case structure

  Main problem: I'm writing a VI that will read data from a data acquisition and write to a text file when I hit a button "registration". To do this, I use the VI of reading DAQmx in a while loop, which is located in a case statement (I hit the 'Save' button for the case of true), which is in another while loop. My DAQmx create Virtual channels screws are outside of the loop, so a wire goes through three structures to connect these screws to the VI DAQmx Read.

  After clicking on 'Save', my VI works until I hit the "Stop" button, how I get error 200088: ' specified is not valid or does not exist. " If anyone can help me get rid of this error, that would be greatly appreciated!

  I enclose my VI and an image of the error.

  Secondary problem: currently, I use two different DAQmx read live: one mentioned above, which lays down: after clicking 'Save' and the other who reads data continuously to display on maps. I want to combine these two, but I don't know if this is possible given the case statement.

  Thank you!

  Hi Alexwright,

  I made some quick changes to demonstrate the producer consumer loop that would be effective in your case. You want to loop of producer in the first while loop so that you use and the same closing DAQmx task. Moving a forwardthis will require some trial and effective change for your application. Please also make sure you use our debugging tools: http://www.ni.com/gettingstarted/labviewbasics/debug.htm.

  I hope this helps.

• DAQmx reads (or writes) in parallel and series

  Is there a performance difference between putting DAQmx reads (or writes) in parallel or series?

  Well said.  In addition, using series would create dependencies of data flow, so the readings could not happen at the time of the soul, where parallel would remove the dependencies.

• How to use DAQmx Read to measure several analog channels

  I have two analog inputs using USB 6221 and I want to measure the voltage of each of them.  I use vi DAQmx-read and I select input analog, 1 sample, several channels, but I do not know how to connect several channels at the entrance of the physical channel.

  Hello, Bernadette.

  For reference - I would recommend ad DAQmx questions here:

  NEITHER Forums: Multifunction Data Acquisition

  http://forums.NI.com/T5/Multifunction-DAQ/BD-p/250

  There are several ways to add multiple channels for a fast task-ni.com look for "select multiple channels DAQmx" gives me this like the hit albums:

  2X8D7F5Z knowledge base: How can I select more than one channel of NOR-DAQmx LabVIEW?

  http://digital.NI.com/public.nsf/allkb/A3A05920BF915F1486256D210069BE49

  Hope that helps!

• DAQmx read - the values on the scale or not? Binary conversion.

  Hey everybody,

  I had a question regarding making the scale and the release of Renault. I use LabVIEW 2009 SP1, with a pilot DAQmx 9.0.2 and a X-Series card. I'm reading the data my DAQ and store it in a binary file.

  How is the acquisition of data read samples, in General? that is if I select NSamp NChan I16 2D Analog on my DAQmx Read, what kind of values can I expect if I was at the exit of the probe data? (Suppose I have readings in mV values and my overall fork's 04:55 V.) When he wrote in the binary file, what happens, what can I expect to see in terms of values - or maybe just descriptively?

  Overall, a little insight would be very helpful. I tried to troubleshoot asymmetric readings I received, so this will help me immensely.

  Thank you.

  Hi Matt87,

  Reading data as I16 will return the result adjusted, not calibrated for 16-bit ADC.

  If you want to write your own binaries, you'll want to include scaling of device - for series X, coefficients a 3rd order polynomial.

  Here are two examples that show how write to a binary file and read the data back.  In this example, scaling coefficients are stored in the file header:

  Continuous gain and voltage drop (binary) chart

  Graph of the acquired binary data

  That said, I would recommend that you look in the record feature integrated TDMS introduced in DAQmx 9.0.  The result is a file appropriate binary .tdms which is a standard format that can be opened in LabVIEW or in several other programs with the plugin.  See the following examples for how to use the function:

  Streaming data and log to the PDM file

  Continuously to log in a PDM file data

  The second example does not force you to read the data in the memory of LabVIEW and use the minimum CPU.  The first example allows you to see the data that is acquired.

  Best regards

• DAQmx read 1 d or 2d

  Attached, I have a 4 channel daqmx read that's nchan 2d - nsample. I can't get the IIR filter works with 2d data. I can operate with 1 d, but this isn't what I wan't. The IIR filter is possible to work with 2d data? The vi works now because I just left the unwired filter.

  When I like you suggested, created the constant of waveform and connected it to the queue, everything was fine. It had been difficult for me, but you nailed. Thank you very much.

• Error-200524 occurred at .vi:2 DAQmx Write (analog 1-d NChan DBL 1Samp)

  I'm trying to generate a signal to usb-6009 of simulated signal.

  However, he keep poping errors:

  Error-200524 occurred at .vi:2 DAQmx Write (analog 1-d NChan DBL 1Samp) if I choose "1 sample on request" in mx data acquisition.

  If I have chaged to "continuous sample", the error has become

  Error-200077 during the property Node DAQmx Timing (arg) 1 DAQmx Timing (sample clock) .vi:3-> 1.vi:Instance:0:1-> Untitled 1 Untitled. VI

  Can someone could take care of my problem?

  Very appreciate

  The limitations of the analog output of your device is documented in the manual and has been considered on several occasions. Because it supports at the time of the application, you can only pass a single value to a moment, not a waveform. The timing is only the software and you can not generate a signal without a lot of jitter and the max frequency will be by the spec.