default flow control values

Similar Questions

• Flow control and Jumbo Mtu

  Hello

  I have a Dell document "Win-Hyperv-2012OS-Config". He asserts that before installing the kit EQL HIT, we have to configure network (tool of Broadcom Advanced Configuration Suite (BINS)) as:

  Option	Value
  Flow control	Rx & Tx active
  Jumbo Mtu	9014

  Is it worth for native Windows 2012 grouping configuration?
  Now I see MTU is configured 1500 on all cards, has it be changed and why?

  Thank you

  You use grouping of NETWORK adapters on a Windows host storage EQL. You can see odd behavior and errors when trying to write to a volume and have only one connection (because THINGS that there is only one card NETWORK).

  Under the special workloads and environments a MTU of 9000 (Jumbo) * can * give you better performance. For sure, you will see a higher latency.

  You must configure your pSwitch first, and then the driver/NIC in the host operating system.  The EQL use JumboFrames automatically if the initiator connects successfully with a MTU of 9000. See the 'reports' in the EQL GroupManager tab. Hold the mouse on one of the initiator of connection messages and look at the end of the line.

  Kind regards

  Joerg

• Flow Control on iSCSI physical NIC software

  Hello

  I want to activate flowcontrol throughout the network iSCSI - how to activate it on the network adapters that are related to the initiator of the software?

  This is a deployment ESX 4.0 U1.

  Concerning

  I'm reasonably sure that the flow control is enabled by default on GB ethernet

  You can use ethtool to view / change settings of network adapters.

  ~ # ethtool vmnic0
  Settings for vmnic0:
          Supported ports: [ TP ]
          Supported link modes:   10baseT/Half 10baseT/Full
                                  100baseT/Half 100baseT/Full
                                  1000baseT/Half 1000baseT/Full
          Supports auto-negotiation: Yes
          Advertised link modes:  10baseT/Half 10baseT/Full
                                  100baseT/Half 100baseT/Full
                                  1000baseT/Half 1000baseT/Full
          Advertised auto-negotiation: Yes
          Speed: 1000Mb/s
          Duplex: Full
          Port: Twisted Pair
          PHYAD: 1
          Transceiver: internal
          Auto-negotiation: on
          Supports Wake-on: g
          Wake-on: g
          Current message level: 0x000000ff (255)
          Link detected: yes
  

  Use

  ethtool -A vmnic0 rx on tx on
  

  to enable flow control for transmit and receive.

• Page fragment bounded-task-Flow Control Flow Help

  jDeveloper: 11.1.1.0.2
  
  I have a question to try to understand the correct way to use control flow case between a bounded-task-flow with fragments of page and a page without limits-task-flow. We have taken the approach of our application to have some shell / container pages to host bounded task flows composed of fragments of page to facilitate the reuse and accelerate development. There are 4 or 5 pages of shell on the unlimited-task-flow applications. From now on, we have about 20 fragments of page that are implemented as a bounded flow task. These fragments don't do much now, which means there is only a single fragment in each delimited-task-flow. The question that I'm going to try to call action from navigation to control flow of one of the fragments to load a page another shell.
  
  For example, shellPage1.jspx contains fragment-flow-1 as a region. In my adfc-config I have shellPage1.jspx and shellPage2.jspx, with the case of 'toShell1' and 'toShell2' control flow, respectively linking two pages. I have a link action related to the 'toShell2' in the fragment that make up fragment-flow-1. When the application is run, shellPage1.jspx and its fragment are displayed. But clicking on the link in the fragment ("toShell2") do absolutely nothing. This not me access the shellPage2.jspx as expected. What I do wrong here or do not understand?
  
  If the fragment is included as include a JSP page, and not a narrow-minded, all workflow works as expected. This is not desirable, as we then need to copy the fragment pageDef in pageDef of the shellPage to get the DataControls function.
  If the faces - config.xml is used instead, and a case of JSF navigation is used, it also works as expected. This is not desirable because we really do want to be mixing adcf-config and faces-config.
  
  So I am really puzzled here... Thanks in advance!

  Hello:
  In your case, the adfc - config.xml has the case of flow control between the pages of the shell. And the task-flow - N.xml or yours-task - flow.xml for each default page fragment does not inherit control flow of the page containing the shell case. In your case, in the task of page fragment - flow.xml, you must add a "Parent Action' to sink to shell page2 for example. The result of 'Parent Action' would be 'toShell2' If you call ShellPage1 page fragment.
  Is it 'OK' or 'Useful' for you? Please mark it as if it does.
  Good luck

  Alex

• Where lives the logic for the types of flow control step?

  For most types of step, the behavior of the type of the step is determined entirely by the configuration of the stage - that is to say, the properties that can be configured in the window type, such as the properties of the step, steps, etc..  But as far as I know, the behavior of the control flow step types (for example, hop, back at the beginning of a block of loop after a late stage) does not seem to be defined by a lower level, flag, attribute or any other configuration item - it seems to be something inherent to the motor TestStand.

  If this is the case, how the TestStand engine knows to provide the functionality for a particular flow control step type?  It runs the appropriate logic based on the name of the step type?  I suspect that this may be the case, because if I create new types of step in copying the types of step ForEach and end without any changes other than to specify the new name for the beginning of the block and end step types, new types of step repeat not the loops as expected.

  Can someone clear this up for me?  Types of flow control step break the model completely define the features by changing the type of step, or I am simply not find relevant configuration items?  I tried to create a new type of end step that allows an expression pre, but it broke my step ForEach (new) type loopback functionality.  Is it possible to do what I want?

  You are right that the engine processes specially the flow control measures. He looks at the name of step type. If you want the same behavior execution, you must keep the original name of type step as a prefix on your step type name, such as NI_Flow_End_CustomizedByMe.

  Also, check out the http://forums.ni.com/t5/NI-TestStand/copy-of-NI-Flow-End-does-not-work/m-p/290170/highlight/true#M88...

  There is the source code that is similar to what the engine makes the steps of flow control. That was the actual code before it moved into the engine. It might be a bit outdated now. I found this on my machine in C:\Program Files (x 86) \National Instruments\TestStand 2010\Components\StepTypes\FlowControl\

• Set control value error 91

  I'm trying to use on a dynamic called vi control value. Control is an object.

  Everything works except if I dynamically load the vi project packed library. When I do that and then set the value of control returns error 91 "the variant data type is not compatible with the data type of wired for the input type.

  Thank you Paul. Here's where I am.

  I am writing a main application which will be integrated into an exe file. The exe will load plugins to a directory. I want the plugins to have a single file, so I initially put the source distributions in llbs. That works fine until you have two files with the same name, even if they are in their own libraries. Which lead me to the project packaged libraries.

  The question as Aristos explains on lava which is the class that I use in my main application and in the packed project library is not really the same category because we're in a lvlib and it is in a lvlibp. So, I put my class in a library and build a library packed one. I then use this library in my main application and plugins. Given that the main application plugins use the same lvlibp that they use the same class and everything works. So I'm going to mark my own post as the solution since Aristos don't post here.

  It's so little pain. The class that I use for communication is a class e-mail called doggies messaging library object that rose created Dalban. It's like a normal queue except that the data type is a class. This means I have to put all my message classes in a library project packed. Because of this I will be rethinking the sharing classes between my main application and plugins. Maybe I'll use something else such as the library of the CMA.

  Fortunately, it is still early in the design of this application. I just discovered the difficulty by a demonstration of the prototype of concept.

• Control values defined by the Index function only works for a running VI?

  I've never used set of control values based on the Index before so I decided to compare it against two other ways to set the controls on the front panel, by using the invoke Ctrl.Val.Set node and nodes for the value property. But if the VI which I am trying to set the controls does not work I get error 1000 say "The VI isn't in a State compatible with this operation." When I run the VI which I am trying to set the controls, I get an error. This is VI really only work if the VI is running? I can't set the values before calling the VI to run dynamically?

  I wonder why you do so in the first place.

  a bit of history. This feature was added to the problem write to items in front by reference is about 1000 times slower than writing to the Terminal. I think that this feature works by writing directly to the transfer buffer. It always ends up by being slower than writing to the Terminal, but only about 10 times slower.

  My company made use of this new feature. We needed it because we have updated thousands of values of frontage on the same VI by reference and labview couldn't keep it up (Yes, probably could have worked around him in a different way, but there is more detail than this...). If your ' e does not update thousands of articles, probably you should not use this feature. Performance savings is not worth the additional development effort it takes.

  It does not work probably because the transfer buffer does not exist when the vi is not running

• How to check link flow control works on EqualLogic?

  I recently had to disable DCB on different switches did not fully support DCB.  Now I want to ensure that EqualLogic Arrays use correctly the link flow control.  I remember a message in the event log earlier who said that flow control is enabled on all interfaces, but I wonder if there is an easier way and makes it more definitive to me to check if flow control is enabled and working on the EqualLogic arrays.  The firmware version is 7.0.9.  I have enabled in the EqualLogic group DCB (as recommended by Dell) and disabled on Ethernet switches.  Thank you.

  Hello

  You need to check the switches, they should show it is activated or not.   EQL paintings will never SEND a pause frame to the switch, it will however, respond to the flowcontrol if make him recover from the switch.

  Note: Not all switches support send flowcontrol.

  Kind regards

• EqualLogic PS4110X flow control problem

  I configured two Powerconnect 8024F switches for use with Equallogic. The firmware version on is 5.0.0.4 and Equallogic firmware 6.0.1 version. I have one on the other's and I use 6 ports on each switch for this. I configured the ports for use with servers accessing the equallogic and equallogic. I created VLANS separated, the size of the mtu 9216 set and enable flow control. Here's the problem: I got an error, or should I say warning on Equallogic saying only: Ethernet flow control has been disabled on one or more interfaces. I checked severeal times configuration but could not find any problems.

  Any suggestion what could be the problem?

  Thank you very much for the help!

  Rafko

  Data Center Bridging is enabled.  DCB is not entirely supported by 8024F switches.   This causes flowcontrol standard port must be disabled.  Disable DCB is in the EQL GUI interface, under group settings.

  This will solve the problem.

• This file does not have a program associated with it for performing this action. Please install a program or, if such is already installed, create an association in the default programs control panel

  Hello-

  I'm looking for here (or get) help directed to the right forum regarding an error message I got when trying to open a PDF file.  The error message indicates "this file does not have a program associated with it for performing this action.  Please install a program or, if such is already installed, create an association in the default programs control panel. "To be quite honest, I don't have the slightest idea as to what to do with respect to this message and I need some advice ASAP.  I have the latest Adobe Acrobat Reader installed and if I have to contact them instead about my problem, please let me know.

  LeeBee

  Hi Leroy,

  I would like to know some information about the problem so that we can help you better.

  The question is specific to the PDF files?

  Thank you for details on the issue.

  I also know that the inconvenience that you are experiencing because of the problem mentioned. I will definitely help you.

  This problem may occur if the exact program is not associated with the file you are trying to open.

  I suggest you to set default programs and associate a file type with a program properly.

  Please see this link:
  Change programs that Windows 7 uses by default
  https://support.Microsoft.com/en-us/help/18539/Windows-7-change-default-programs

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• create associations in the default programs control panel

  I use Windows 7. When I go to my photos and do a right-click on a photo and go to send the picture by e mail I receive a notice 'no file association, to create an association in the default programs control panel. I run g. Im not computer savvy very mail any help would be appreciated.

  Hello

  a. what email client you have installed on your computer?
  b. how you try to access gmail on your computer?

  If you have any mail client installed such as outlook, then you can set outlook as the default e-mail client.
  If you use gmail from Internet Explorer, then you may not be able to set as the default program.

  Hope this information is useful.

  Umesh P - Microsoft Support

• "This file has no program associated with it for performing this action. Please install a program or, if such is already installed, create an association in the default programs control panel. »

  When I click on the browser icon in the task bar or try to run Explorer in the Quick Start menu, I get the error

  "This file has no program associated with it for performing this action. Please install a program or, if such is already installed, create an association in the default programs control panel. "But I can't find that explore registered in the default programs list.

  The guy from Solution Explorer

  I think I have this time. See repair error file Association at the launch of Windows Explorer in Windows 7. We were close, however.

  Ramesh Srinivasan . The Winhelponline Blog
  Microsoft MVP, Windows desktop experience

• the default programs control panel

  Sometimes when clicking on an email address I get the error message telling me that there is no associated messaging program to perform the requested action.

  To install an e-mail program or if it is installed, to create an association in the default programs control panel? What should do?

  You have an installed like Windows Live Mail or Thunderbird or Outlook 2010 e-mail client?

  If you have you can set/restore by default using this information...

  http://Windows.Microsoft.com/en-us/Windows7/change-default-programs-using-set-program-access-and-computer-defaults

  http://Windows.Microsoft.com/en-us/Windows7/change-which-programs-Windows-uses-by-default

  http://Windows.Microsoft.com/en-us/Windows7/set-program-access-and-computer-defaults-frequently-asked-questions

• error: there is no associated messaging program to perform the requested action. Install an e-mail program or, if such is already installed, create an association in the default programs control panel

  Installed Windows7 Enterprise (evaluation) 32 bits have a database custom (32 bit) when I press the close button, an e-mail icon in the taskbar - nothing happens with the program except the screen turns off, when you press the email icon it is an error message - there is no associated messaging program to perform the requested action. Install an e-mail program or, if such is already installed, create an association in the default programs control panel

  There is no email function associated with the close button

  using the close button of other windows in the work of database correctly.

  TBird is installed and works well

  Have solved the problem - the app was looking for a MAPI - outlook installed e-mail client and not more errors. Thank you much for the help

• Explorer.exe: "this file doesn't have a program associated with it for performing this action. Please install a program or, if such is already installed, create an association in the default programs control panel. »

  I find this weird problem affecting that explorer.exe and not any other .exe files. When I open explorer.exe in the taskbar or the C:\Windows\explorer.exe, the dialog box opens and indicates "this file does not have a program associated with it for performing this action. Please install a program or, if such is already installed, create an association in the default programs control panel. ». The control panel default programs Dosen t State .exe in the list of protocols and I find it complicated to press the windows logo and click computer each time. Please tell me that there is a way to solve this problem by means of edit this record.

  I have not tried running sfc/scannow then chkdsk/f, two found no error.

  -------------------------------------------------------------------------

  Name of the operating system Microsoft Windows 7 Ultimate
  Version 6.1.7600 Build 7600
  Manufacturer of operating system Microsoft Corporation
  System Type X 86-based PC
  Processor Intel (r) Core (TM) 2 CPU Quad Q9300 @ 2.50 GHz, 2500 Mhz, 4 Lossnay, 4 logical processors
  Windows directory C:\Windows
  System directory C:\Windows\system32
  Boot Device \Device\HarddiskVolume1
  Locale Singapore
  Hardware Abstraction Layer Version = "6.1.7600.16385".
  Normal time zone schedule Malay Peninsula
  Installed RAM GB 5,00
  3.00 GB total physical memory
  936 MB available physical memory
  12.5 GB total virtual memory
  9,88 GB available virtual memory
  Page file space GB 9.47
  Paging file C:\pagefile.sys

  Hello brandongwh,

  Check out the post here for help with a solution that should help your problem with Explorer.exe.

  If this does not help, then please reply back and let us know.

  Thank you

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think