default listening port no

I use 10g release 2 under oel 5.5 inside vmware
I want to create multiple listener to my database and aal of them to be registered dynamically
I had created two earphone using netmgr one is by default is not set by default to port 1522
Here is my listener.ora file

AUDITEUR1 =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP (PORT = 1522))(HOST = pawii.oraexpert.com))
)

LISTENER =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = pawii.oraexpert.com) (PORT = 1521))
)

I want to record dynamically

I pulled lsnrctl start
and lsnrctl start (no default listening port) auditeur1
both the listener don't start but the default receiver support no no services
I had bu db start again its not supporting all services why?
and if I specify services database with the help of netmgr then the entry goes in listener.ora and make static recording which always show status unknown
so, how can I do dynamic registration?

You must indicate your instance where are listeners. Run these two commands:

alter system set local_listener='(address_list=(ADDRESS = (PROTOCOL = TCP)(HOST = pawii.oraexpert.com)(PORT = 1522))(ADDRESS = (PROTOCOL = TCP)(HOST = pawii.oraexpert.com)(PORT = 1521)))';
alter system register;

and the registration will then be automatic.

Tags: Database

Similar Questions

How to change the default listening port?

Hi all
11.2.0.4
RHEL 6.5
I managed to install Oracle Db 11.2.0.4 on RHEL 6.5
He created a default listener uses port 1521.
With the following entries in listener.ora.
listener.ora # Network Configuration file: /u01/app/oracle/product/11.2.0.4/db_1/network/admin/listener.ora
# Generated by Oracle configuration tools.
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = CIP)(KEY = EXTPROC1521))
(ADDRESS = (PROTOCOL = TCP) (HOST = ip-10-0-0 - 216.ec2.internal)(PORT = 1521))
)
)
ADR_BASE_LISTENER = / u01/app/oracle
How can I change the port in 1522? Can I just he replace value of listener.ora?
Should I also change the value of KEY = EXTPROC1521 to KEY = EXTPROC1522?

I tried to change the port in 1522 in the listener.ora but when I start "lsnrctl status".

[oracle@ip-10-0-0-216 admin] $ lsnrctl status
LSNRCTL for Linux: Version 11.2.0.4.0 - Production on March 7, 2015 06:19:54
Copyright (c) 1991, 2013, Oracle. All rights reserved.
Connection to (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC) (KEY = EXTPROC1521)))
STATUS of the LISTENER
------------------------
Alias LISTENER
Version TNSLSNR for Linux: Version 11.2.0.4.0 - Production
Start date March 7, 2015 06:19:05
Uptime 0 days 0 h 0 min 49 sec
Draw level off
Security ON: OS Local Authentication
SNMP OFF
Parameter Listener of the /u01/app/oracle/product/11.2.0.4/db_1/network/admin/listener.ora file
The listener log file /U01/app/Oracle/diag/tnslsnr/IP-10-0-0-216/listener/alert/log.XML
Summary of endpoints listening...
(DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = EXTPROC1521)))
(DESCRIPTION = (ADDRESS = (PROTOCOL = tcp) (HOST = ip-10-0-0 - 216.ec2.internal)(PORT=1522)))
The listener supports no services
The command completed successfully
Now, it does not support the services ORCL which is the default database installed
I can not connect to the database the string '@orcl' of both connection using the default
[oracle@ip-10-0-0-216 admin] $ sqlplus system/manager@orcl
SQL * more: version 11.2.0.4.0 Production on Sat Mar 7 06:23:50 2015
Copyright (c) 1982, 2013, Oracle. All rights reserved.
ERROR:
ORA-12541: TNS:no listener
Help, please...
Thank you
MK

Hello

As said earlier after which the listening port, you must update the parameter local_listener database as below:

ALTER system set local_listener ='(ADDRESS = (PROTOCOL = TCP) (HOST = ip-10-0-0 - 216.ec2.internal)(PORT=1522))'

editing the system registry;

HTH,

Pradeep

Creation of database of cluster requires default listener configured and executed in grid House Infrastructure.

Hello!
I created the new database with DBSA in configuration RAC (NŒUD 2)
Oracle Database 11 g Enterprise Edition Release 11.2.0.3.0 - 64 bit
Release of Red Hat Enterprise Linux Server 5.8
Requirements has successfully passed:
[oracle@db1-mng ~] $ cluvfy stage - pre dbcfg - n mng - db1, db2 - mng - d
/U01/app/Oracle/product/11.2.0.3/dbhome_1
Perform preliminary checks for database configuration
Check accessibility of node...
Accessibility of node check from node "db1 - mng.
Check the user equivalence...
User equivalence check passed for user 'oracle '.
Verify node connectivity...
Checking hosts config file...
The hosts config file verification successful
Check: connectivity interface node 'bondeth0 '.
Connectivity node passed to the interface 'bondeth0 '.
Check the TCP connectivity to subnet "10.116.176.196."
Check: connectivity interface node 'bondib0 '.
Connectivity to the node passed to the interface 'bondib0 '.
Check the TCP connectivity to subnet "192.168.18.10."
Checking consistency of subnet mask...
Consistency of subnet mask check passed for subnet
'10.116.176.196 '.
Consistency of subnet mask check passed for subnet
'192.168.18.10 '.
Verification of consistency for the last subnet mask.
Check the passed node connectivity
Checking for multicast communication...
Check "10.116.176.196" for multicast communication subnet with
Multicast group '230.0.1.0 '...
Subnet check "10.116.176.196" for multicast communication with
from '230.0.1.0' multicast group
Check "192.168.18.10" for multicast communication subnet with
Multicast group '230.0.1.0 '...
Subnet check "192.168.18.10" for multicast communication with
from '230.0.1.0' multicast group
Control of transmitted multicast communication.
Total memory check passed
Check the available memory
Checking space last swap
Check the disk space free past for
'db1-mng:/u01/app/oracle/product/11.2.0.3/dbhome_1 '.
Check the disk space free past for
'db2-mng:/u01/app/oracle/product/11.2.0.3/dbhome_1 '.
Free disk space for audit "db1 - mng: / tmp '.
Free disk space for audit "db2 - mng: / tmp '.
Check for multiple users with the value of the UID 1000 ago
Check for existence of user for 'oracle '.
Existence of group check passed for "oinstall".
Existence group check passed for "dba".
Membership check for user 'oracle' in group 'oinstall' [as principal]
past
Membership to check for 'oracle' user group 'dba' spent
Run control the level of the past
Hard deadline check passed for "maximum open file."
"descriptors of '.
Verification of limits soft for "maximum open file."
"descriptors of '.
Hard limits check passed for "maximum user process.
The soft limits check passed for "maximum user process.
The system architecture check past
Check the version of the kernel spent
Kernel parameter check passed for "semmsl.
Kernel parameter check passed for "semmns.
Kernel parameter check passed for "semopm.
Kernel parameter check passed for "semmni.
Kernel parameter check passed for "shmmax.
Kernel parameter check passed for "shmmni(5)."
Kernel parameter check passed for "shmall.
Kernel parameter check passed for 'file-max.
Kernel parameter check passed for "ip_local_port_range.
Kernel parameter check passed for "rmem_default."
Kernel parameter check passed for "rmem_max.
Kernel parameter check passed for "wmem_default."
Kernel parameter check passed for "wmem_max.
Kernel parameter check passed for "aio-max-nr.
Existence of package check passed to 'make it '.
Existence of package check for "binutils".
Existence of package check passed for "gcc (x86_64).
Existence of package check for "libaio (x86_64).
Existence of package check for 'glibc (x86_64).
Existence of package check passed for
"compat-libstdc ++-33 (x86_64).
Existence of package check passed for
"elfutils-libelf (x86_64).
Existence of package check passed for "elfutils-libelf-devel '.
Existence of package check passed for 'glibc-common ".
Existence of package check for 'glibc-devel (x86_64).
Existence of package check for ' glibc headers.
Existence of package check passed for "gcc - c++ (x86_64).
Existence of package check for "libaio-devel (x86_64).
Existence of package check for 'libgcc (x86_64).
Existence of package check for 'libstdc ++ (x86_64).
Existence of package check passed for
'libstdc ++ - devel (x86_64).
Existence of package check for "sysstat".
Existence of package check for 'ksh '.
Check for multiple users with the value of the UID 0 passes
ID of current group check passed
Audit of departure for the coherence of the primary root group
user
Check the consistency of the primary group of the user root past
CRS checking the integrity...
Consistency of version Clusterware spent
Checking the integrity of the src passed
Checking node application existence...
Verification of the existence of the node VIP application (required)
VIP application node check past
Verification of the existence of the application of NETWORK node (required)
Application node passed control NETWORK
Verify the existence of GSD (optional) application node
Application node GSD is in offline mode on nodes "mng - db1, db2 - mng"
Verification of the existence of the application of ONS node (optional)
ONS node application check past
Check the consistency of zone past
Check beforehand for the database configuration was successful.
------------------------------------------
[oracle@db1-mng ~] $ ps - aef | grep lsnr
10435 1 0 2014 Oracle? 00:09:57
/U01/app/Oracle/product/11.2.0.3/dbhome_1/bin/tnslsnr LISTENER
-inherit
10447 1 0 2014 Oracle? 00:14:10
/U01/app/11.2.0.3/grid/bin/tnslsnr LISTENER_SCAN1-inherit
Oracle 58226 74449 14:00 0 pts/0 00:00:00 grep
LSNR
------------------------------------------
[oracle@db1-mng ~] $ lsnrctl LISTENER status
LSNRCTL for Linux: Version 11.2.0.3.0 - Production on 16 April 2015
11:56:48
Connection to
(DESCRIPTION = (ADDRESS = (PROTOCOL = IPC) (KEY = LISTENER)))
STATUS of the LISTENER
Alias LISTENER
Settings for the listen port file
/U01/app/Oracle/product/11.2.0.3/dbhome_1/network/admin/listener.ora
Log file of listener
/U01/app/Oracle/product/11.2.0.3/dbhome_1/log/diag/tnslsnr/db1-MNG/listener/alert/log.XML
Listen to endpoint points summary...
(DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = LISTENER)))
(DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=10.116.176.129) (PORT = 1521)))
(DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=10.116.176.100) (PORT = 1521)))
Summary of services...
Service '+ ASM' a 1 instance (s).
Instance '+ ASM1' READY State, has 1 operation for this
service...
Service 'COM' has 1 instance (s).
Instance "COM1", State LOAN, has 1 operation for this
service...
Service 'COMXDB' has 1 instance (s).
Instance "COM1", State LOAN, has 1 operation for this
service...
'PM' service has 1 instance (s).
Instance "PM1" READY State, has 1 operation for this
service...
Service 'PMXDB' has 1 instance (s).
Instance "PM1" READY State, has 1 operation for this
service...
Service 'TEST' has 1 instance (s).
Instance "TEST1", State LOAN, has 1 operation for this
service...
Service 'TESTXDB' has 1 instance (s).
Instance "TEST1", State LOAN, has 1 operation for this
service...
The command completed successfully
----------------------------
[oracle@db1-mng ~] $ lsnrctl status LISTENER_SCAN1
LSNRCTL for Linux: Version 11.2.0.3.0 - Production on 16 April 2015
14:12:13
Connection to
(DESCRIPTION = (ADDRESS = (PROTOCOL = IPC) (KEY = LISTENER_SCAN1)))
STATUS of the LISTENER
Alias LISTENER_SCAN1
Settings for the listen port file
/U01/app/11.2.0.3/grid/network/admin/listener.ora
Log file of listener
/U01/app/11.2.0.3/grid/log/diag/tnslsnr/db1-MNG/listener_scan1/alert/log.XML
Listen to endpoint points summary...
(DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = LISTENER_SCAN1)))
(DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=10.116.176.197) (PORT = 1521)))
Summary of services...
Service 'COM' has 2 occurrences.
Instance "COM1", State LOAN, has 1 operation for this
service...
Instance "COM2", State LOAN, has 1 operation for this
service...
Service 'COMXDB' has 2 occurrences.
Instance "COM1", State LOAN, has 1 operation for this
service...
Instance "COM2", State LOAN, has 1 operation for this
service...
'PM' service has 2 occurrences.
Instance "PM1" READY State, has 1 operation for this
service...
Instance "PM2", State LOAN, has 1 operation for this
service...
Service 'PMXDB' has 2 occurrences.
Instance "PM1" READY State, has 1 operation for this
service...
Instance "PM2", State LOAN, has 1 operation for this
service...
Service 'TEST' has 2 occurrences.
Instance "TEST1", State LOAN, has 1 operation for this
service...
Instance "TEST2", State LOAN, has 1 operation for this
service...
Service 'TESTXDB' has 2 occurrences.
Instance "TEST1", State LOAN, has 1 operation for this
service...
Instance "TEST2", State LOAN, has 1 operation for this
service...
The command completed successfully
------------------------
Also successful on the second node db2 - mng to LISTENER_SCAN2, LISTENER_SCAN3.
When I try to run the command "dbca responsefile - /home/oracle/PR/PRN.rsp-silent ' displays an error:
Creation of database of cluster requires the default listening port configured and
currents of the Home Network Infrastructure. Use NETCA in grid Infrastructure - home
"/ u01/app/11.2.0.3/grid" to set up a front listening port
instance.
RAC-database now works in production. Manipulation of the Junk listener.
How can I get around the error?
In particular all databases have been created in the same way, the truth, about a year ago.

Thank you, Thomas! I chose the first method) OK

How can I display an error message on the listening port close popup without closing the popup.

Hi Experts,
JDeveloper 12.1.3.0.0
How can I display an error message on the listening port close popup without closing the popup.
Thank you
Roy

As its name suggests, close listener of popup is called when popup is closed so you can not do this.

If you want to display the popup message, use your own buttons instead of the ok/cancel default buttons and close the popup programmatically.

Dario

Apex listening port Configuration problem.

Hello

I wanted to try the latest Restful services in apex 4.2, I decided to install 2.0 listener Apex. I downloaded the file and followed the steps in the installation notes. As a sine qua non, I configured Restful services with success in the apex 4.2 with Oracle 11 g Express Edition. However, the installation of listener seems to be not correctly complete the following installation feed back.

D:\software\apex_listener>java -jar apex.war
This Listener instance has not yet been configured.
Please complete the following prompts

Enter the location to store configuration data:d:\apexlistnerconf
Dec 27, 2012 3:34:47 PM oracle.dbtools.common.config.cmds.ConfigDir execute
INFO: Set config.dir to d:\apexlistnerconf in: D:\software\apex_listener\apex.war
Dec 27, 2012 3:34:49 PM oracle.dbtools.common.config.file.ConfigurationFolder logConfigFolder
INFO: Using configuration folder: D:\apexlistnerconf\apex
Enter the name of the database server [localhost]:
Enter the database listen port [1521]:
Enter 1 to specify the database service name, or 2 to specify the database SID [1]:2
Enter the database SID [xe]:
Enter the database user name [APEX_PUBLIC_USER]:
Enter the database password for APEX_PUBLIC_USER:
Password must not be empty
Enter the database password for APEX_PUBLIC_USER:
Confirm password:
Enter 1 to enter passwords for the RESTful Services database users (APEX_LISTENER,APEX_REST_PUBLIC_USER), 2 to use the same password as used for APEX_PUBLIC_USER or, 3 to skip this step [1]:3
Dec 27, 2012 3:37:03 PM oracle.dbtools.common.config.file.ConfigurationFiles update
INFO: Updated configurations: defaults, apex
Enter 1 if you wish to start in standalone mode or 2 to exit [1]:
Enter the APEX static resources location or Enter to skip:D:\software\apex42en\apex\images
Enter the HTTP port [8080]:
Dec 27, 2012 3:41:17 PM oracle.dbtools.standalone.Standalone execute
INFO: NOTE:

Standalone mode is designed for use in development and test environments. It isnot supported for use in production environments.

Dec 27, 2012 3:41:17 PM oracle.dbtools.standalone.Standalone execute
INFO: Starting standalone Web Container in:  d:\apexlistnerconf\apex
Dec 27, 2012 3:41:17 PM oracle.dbtools.standalone.Deployer deploy
INFO: Will deploy application path = d:\apexlistnerconf\apex\apex\WEB-INF\web.xml
Dec 27, 2012 3:41:17 PM oracle.dbtools.standalone.Deployer deploy
INFO: Deployed application path = d:\apexlistnerconf\apex\apex\WEB-INF\web.xml
Dec 27, 2012 3:41:18 PM oracle.dbtools.common.config.file.ConfigurationFolder logConfigFolder
INFO: Using configuration folder: D:\apexlistnerconf\apex
Default Database connection not configured properly
Dec 27, 2012 3:41:20 PM oracle.dbtools.rt.web.SCListener contextInitialized
INFO: Oracle Application Express Listener initialized
Application Express Listener version : 2.0.0.354.17.06
Application Express Listener server info: Grizzly/1.9.49

Dec 27, 2012 3:41:20 PM com.sun.grizzly.Controller logVersion
INFO: GRIZZLY0001: Starting Grizzly Framework 1.9.49 - 12/27/12 3:41 PM
Dec 27, 2012 3:41:20 PM com.sun.grizzly.SelectorHandlerRunner handleSelectException
SEVERE: doSelect IOException
java.net.BindException: No free port within range: 8080=com.sun.grizzly.http.SelectorThreadHandler@480d41f3
        at com.sun.grizzly.TCPSelectorHandler.initSelector(TCPSelectorHandler.java:432)
        at com.sun.grizzly.TCPSelectorHandler.preSelect(TCPSelectorHandler.java:378)
        at com.sun.grizzly.SelectorHandlerRunner.doSelect(SelectorHandlerRunner.java:188)
        at com.sun.grizzly.SelectorHandlerRunner.run(SelectorHandlerRunner.java:132)
        at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(Unknown Source)
        at java.util.concurrent.ThreadPoolExecutor$Worker.run(Unknown Source)
        at java.lang.Thread.run(Unknown Source)
Dec 27, 2012 3:41:20 PM com.sun.grizzly.http.SelectorThread$3 onException
SEVERE: Exception during starting the controller
java.net.BindException: No free port within range: 8080=com.sun.grizzly.http.SelectorThreadHandler@480d41f3
        at com.sun.grizzly.TCPSelectorHandler.initSelector(TCPSelectorHandler.java:432)
        at com.sun.grizzly.TCPSelectorHandler.preSelect(TCPSelectorHandler.java:378)
        at com.sun.grizzly.SelectorHandlerRunner.doSelect(SelectorHandlerRunner.java:188)
        at com.sun.grizzly.SelectorHandlerRunner.run(SelectorHandlerRunner.java:132)
        at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(Unknown Source)
        at java.util.concurrent.ThreadPoolExecutor$Worker.run(Unknown Source)
        at java.lang.Thread.run(Unknown Source)
java.net.BindException: No free port within range: 8080=com.sun.grizzly.http.SelectorThreadHandler@480d41f3
        at com.sun.grizzly.TCPSelectorHandler.initSelector(TCPSelectorHandler.java:432)
        at com.sun.grizzly.TCPSelectorHandler.preSelect(TCPSelectorHandler.java:378)
        at com.sun.grizzly.SelectorHandlerRunner.doSelect(SelectorHandlerRunner.java:188)
        at com.sun.grizzly.SelectorHandlerRunner.run(SelectorHandlerRunner.java:132)
        at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(Unknown Source)
        at java.util.concurrent.ThreadPoolExecutor$Worker.run(Unknown Source)
        at java.lang.Thread.run(Unknown Source)
Dec 27, 2012 3:41:20 PM oracle.dbtools.standalone.Standalone execute
INFO: http://localhost:8080/apex started.

Simply, it crashes in the last line, and I couldn't make any progress.

Can you please help to find out what was wrong?

Thanks in advance.

Kind regards

Natarajan

Hello

I updated the apex listener port 8080 and it does not give this error now.

However, he always says "Database connection by default not configured correctly"

I gave the name of SID as xe, which is the default value and that the correct SID for my DB also.
>

SID = xe is correct since you are using 11g XE.

What is more important, is that you may be able to access the Apex Application Builder via the ApexListener or not.
If Apex is not accessible, then the thing to check would be the Apex_Public_user password. Can you connect to XE using Apex_Public_user with the password that you provided when setting up the ApexListener?
Also make sure the Apex_Public_user and 2 other users ApexListener 2.0EA, are UNLOCKED.

See you soon,.

How to find the values of the parameters of a default listener using LSNRCTL
Hello
I have a default listener with name as 'lsnr_abcd' in the default port.
I'm on 10.2.0.4 version database. If I want to know the parameter values (such as displaymode, dynamic_registration, etc.)
for a listener by default, should what command I use?

I know that for the default listener, we can do the following

(1) run lsnctl
(2) show dynamic_registration

What should I run if I want to get this detail to a listener of "lsnr_abcd".

Thank you
Delphine
After setting your current listener to the default listener, not the same

lsnrctl > CURRENT_LISTENER SET lsnr_abcd

You can run additional commands without your name of the listener

lsnrctl > set DISPLAYMODE

Published by: renee_mathieu on July 19, 2012 06:53

Published by: renee_mathieu on July 19, 2012 06:54

Chaning listening port
Hi all

In our society, the evaluation of the safety, the security team recommended to change port 1521 listenter the number. We are plannig to change that in 1530.
I referred to the note: change default listener numeroport [359277.1 ID] and it is quite clear to me.

Now we have Portal/soa/bi/dw applications/db (oracle) connection to this database. now is there a way out of this intense work to change each application connection?

Any idea

Kai
Everything can not think. If any application refers to the old headphone port, you must manually change the application's files to point to the new port.

HTH
Aman...

Configuring services on the listening port
Hi s/n,.

I use a TEST database on a server with port 1521. I created a database over the same DEV server manually.

Now, I was to set up the new DEV with the listener. My current file Listener and TNSname file is attached. Please help me for new DEV that I put in listener.ora and tnsnames.ora database entries.

My name of the listener's TEST. I also need to use the same port for the two DBs as single port 1521 is open from the firewall.

------------------------------------------- Listener.ora ------------------------------------------------------

TEST =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = CIP)(KEY= EXTPROCTEST))
(ADDRESS = (PROTOCOL = TCP)(Host= localhost) (Port = 1521))
)

SID_LIST_TES =
(SID_LIST =
(SID_DESC =
(ORACLE_HOME = u01/app/oracle/product/10.2.0)
(SID_NAME = TEST)
)
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = u01/app/oracle/product/10.2.0)
(= Extproc PROGRAM)
)
)

STARTUP_WAIT_TIME_TEST = 0
CONNECT_TIMEOUT_TEST = 10
TRACE_LEVEL_TEST = OFF

LOG_DIRECTORY_TEST = /u01/app/oracle/product/10.2.0/network/admin
LOG_FILE_TEST = TEST
TRACE_DIRECTORY_TEST = /u01/app/oracle/product/10.2.0/network/admin
TRACE_FILE_TEST = TEST
ADMIN_RESTRICTIONS_TEST = OFF

---------------------------------------- tnsnames.ora ------------------------------------------------

TEST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = tcp)(HOST=localhost) (PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = TEST)
(INSTANCE_NAME = TEST)
)
)

--------------------------------------------------------------------------------------------------------------

Please help this settings.

Thank you
-Samar-
Nome02 wrote:
Hi s/n,.

I use a TEST database on a server with port 1521. I created a database over the same DEV server manually.

Now, I was to set up the new DEV with the listener. My current file Listener and TNSname file is attached. Please help me for new DEV that I put in listener.ora and tnsnames.ora database entries.

My name of the listener's TEST. I also need to use the same port for the two DBs as single port 1521 is open from the firewall.

------------------------------------------- Listener.ora ------------------------------------------------------

TEST =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = CIP)(KEY= EXTPROCTEST))
(ADDRESS = (PROTOCOL = TCP)(Host= localhost) (Port = 1521))
)

SID_LIST_TES =
(SID_LIST =
(SID_DESC =
(ORACLE_HOME = u01/app/oracle/product/10.2.0)
(SID_NAME = TEST)
)
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = u01/app/oracle/product/10.2.0)
(= Extproc PROGRAM)
)
)

STARTUP_WAIT_TIME_TEST = 0
CONNECT_TIMEOUT_TEST = 10
TRACE_LEVEL_TEST = OFF

LOG_DIRECTORY_TEST = /u01/app/oracle/product/10.2.0/network/admin
LOG_FILE_TEST = TEST
TRACE_DIRECTORY_TEST = /u01/app/oracle/product/10.2.0/network/admin
TRACE_FILE_TEST = TEST
ADMIN_RESTRICTIONS_TEST = OFF

---------------------------------------- tnsnames.ora ------------------------------------------------

TEST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = tcp)(HOST=localhost) (PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = TEST)
(INSTANCE_NAME = TEST)
)
)

--------------------------------------------------------------------------------------------------------------

Please help this settings.

Thank you
-Samar-

First of all, I wouldn't name my interlocutor 'TEST '. Use the default name of the LISTENING port. Why complicate your life? The auditor is the auditor for all the db on this box. Do not confuse the issue by appointing him as if he was linked to a specific database. It must become more obvious now that you add additional databases.

Second, a listener can serve several databases and simply to a port to do. This port 1521 is used by the listener to listen for requests to the databases all this services. It has nothing to do with the databases themselves. They care what port listening on the listening port. The actual connection between the client and the database do not use this port.

Thirdly, remember that tnsnames.ora is used by the CLIENT process. Listener.ora is used by the listener on the host: it's a conifiguration host-side. The answers of others that you don't need to worry tnsnames - you only need to set ORACLE_SID - applies only to client processes running on the same box as the db. Remote clients do necessary relevant tnsnames entry.

Fourth, you ask what to put in your listener.ora. Review the file. You see the section named SID_LIST_TES (which looks like a typo to me), and under that, you have two entries SID_DESC? Don't you see that one of these entries SID_DESC is for your existing TEST database? If you don't feel comfortable that copy to an another SID_DESC and edit it accordingly (from so that you have an entry SID_DESC for TEST and another for DEV) then just fire upward the netca utility in your ORACLE_HOME and let him help you add.

Fifth, you ask what to put in your tnsnames.ora. Review the file. You see a clearly delimited input for TEST? If you feel able to make a copy of this entry and change it to DEV, then simply run the netca utility in your ORACLE_HOME and let it help you add.

Sixthly, in your tnsnames file really useless both SERVICE_NAME as INSTANCE_NAME. Drop the INSTANCE_NAME.

Change the listening port
I am running Oracle 10.2 on Solaris. I want to change the listening port of 1521 to 2690. I've read that I'm supposed to change /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora and restart the receiver. Here's my listener.ora:

OPENVIEWLISTENER =
(DESCRIPTION =
(ADDRESS_LIST =
((ADDRESS = (PROTOCOL = tcp (PORT = 2690))(HOST=flare)))
SID_LIST_OPENVIEWLISTENER =
(SID_LIST =
(SID_DESC =
(GLOBAL_DBNAME = openview)
(ORACLE_HOME=/opt/oracle/product/10.2.0/db_1)
(SID_NAME = OpenView))
)

After the reboot, it is still the 1521:

bash-beginning of lsnrctl $ 3.00

LSNRCTL for Solaris: Version 10.2.0.1.0 - Production on 24-AUG-2008 16:53:33

Copyright (c) 1991, 2005, Oracle. All rights reserved.

From /opt/oracle/product/10.2.0/db_1/bin/tnslsnr: Please wait...

TNSLSNR for Solaris: Version 10.2.0.1.0 - Production
System settings file is /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora
Log messages written to /opt/oracle/product/10.2.0/db_1/network/log/listener.log
Listen on: (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=flare.halcyoninc.com) (PORT = 1521)))

Connection to (ADDRESS = (PROTOCOL = tcp)(HOST=) (PORT = 1521))
STATUS of the LISTENER
-----
Alias LISTENER
For Solaris TNSLSNR version: Version 10.2.0.1.0 - Production
Departure date 24-AUG-2008 16:53:34
Uptime 0 days 0 h 0 min 0 sec
Draw level off
Security ON: OS Local Authentication
SNMP OFF
Parameter Listener of the /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora file
The listener log file /opt/Oracle/product/10.2.0/Db_1/network/log/listener.log
Summary of endpoints listening...
(DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=flare.halcyoninc.com) (PORT = 1521)))
The listener supports no services
The command completed successfully

What I am doing wrong? :(

user527462 wrote:
I am running Oracle 10.2 on Solaris. I want to change the listening port of 1521 to 2690. I've read that I'm supposed to change /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora and restart the receiver. Here's my listener.ora:

OPENVIEWLISTENER =
(DESCRIPTION =
(ADDRESS_LIST =
((ADDRESS = (PROTOCOL = tcp (PORT = 2690))(HOST=flare)))
SID_LIST_OPENVIEWLISTENER =
(SID_LIST =
(SID_DESC =
(GLOBAL_DBNAME = openview)
(ORACLE_HOME=/opt/oracle/product/10.2.0/db_1)
(SID_NAME = OpenView))
)

After the reboot, it is still the 1521:

bash-beginning of lsnrctl $ 3.00

LSNRCTL for Solaris: Version 10.2.0.1.0 - Production on 24-AUG-2008 16:53:33

Copyright (c) 1991, 2005, Oracle. All rights reserved.

From /opt/oracle/product/10.2.0/db_1/bin/tnslsnr: Please wait...

TNSLSNR for Solaris: Version 10.2.0.1.0 - Production
System settings file is /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora
Log messages written to /opt/oracle/product/10.2.0/db_1/network/log/listener.log
Listen on: (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=flare.halcyoninc.com) (PORT = 1521)))

Connection to (ADDRESS = (PROTOCOL = tcp)(HOST=) (PORT = 1521))
STATUS of the LISTENER
-----
Alias LISTENER
For Solaris TNSLSNR version: Version 10.2.0.1.0 - Production
Departure date 24-AUG-2008 16:53:34
Uptime 0 days 0 h 0 min 0 sec
Draw level off
Security ON: OS Local Authentication
SNMP OFF
Parameter Listener of the /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora file
The listener log file /opt/Oracle/product/10.2.0/Db_1/network/log/listener.log
Summary of endpoints listening...
(DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=flare.halcyoninc.com) (PORT = 1521)))
The listener supports no services
The command completed successfully

What I am doing wrong? :(

Your listener.ora sets a listener named OPENVIEWLISTENER. You have not specified the name of the listener when starting it and so he went with the default values (name of the LISTENER listener and so on). The command you are looking for is lsnrctl start OPENVIEWLISTENER

concerning

Niall Litchfield
http://www.orawin.info/

Change Windows 7 default serial port settings

I need help how do I change the way Windows 7 control a default serial port COM1. I use a serial cable very easy to control the special with external hardware. The serial cable only use the RTS and DTR, GND pin of the cable and does not require special hardware drivers. I used the camera on several versions of Windows 95 to XP without any problem at all with serial ports. With Windows 95 - XP serial COM1 port's RTS and DTR lines defined 'stop' by default. I just upgraded to a new computer with Windows 7 and now have a problem with the serial port.

For my problem, I need to have the serial port to be 'stop' default until load control software and specifically opens the serial port to turn on the external device. Using a serial port data Tester (a lot of green and Red led) I see that as soon as Windows 7 starts, it automatically sets the lines DTR, RTS and TD to serial port as "HOT" (high voltage). This is not acceptable because it activates the external hardware until the control software is loaded! Similarly when the control software is closed and the serial port is released in Windows 7, the serial port DB, RTS and TD lines are again defined as "HOT" (high voltage) by Windows.

Computer: Dell Optiplex 745
Windows 7 Pro 64 bit with SP1 installed
Serial port on motherboard: Intel ICH8/ICH8R LPC Interface Controller 2810
Serial driver: Microsoft 6.1.7600.16385 (is up-to-date)
```
   Settings for COM1:
   -------------------
   Baud Rate:     9600
   Data Bits:     8
   Parity:        None
   Stop Bits:     1
   Flow Control:  None
```
I spent hours looking at the Manager of devices/port settings and try to find anything online with no luck. Is it possible that this is because of the way Windows 7 plug-n-play manages the serial port? How can I turn it off then the port by default as if it was on XP and earlier versions of Windows is 'off '?

Thanks, Dave
I need help how do I change the way Windows 7 control a default serial port COM1. I use a serial cable very easy to control the special with external hardware. The serial cable only use the RTS and DTR, GND pin of the cable and does not require special hardware drivers. I used the camera on several versions of Windows 95 to XP without any problem at all with serial ports. With Windows 95 - XP serial COM1 port's RTS and DTR lines defined 'stop' by default. I just upgraded to a new computer with Windows 7 and now have a problem with the serial port.

For my problem, I need to have the serial port to be 'stop' default until load control software and specifically opens the serial port to turn on the external device. Using a serial port data Tester (a lot of green and Red led) I see that as soon as Windows 7 starts, it automatically sets the lines DTR, RTS and TD to serial port as "HOT" (high voltage). This is not acceptable because it activates the external hardware until the control software is loaded! Similarly when the control software is closed and the serial port is released in Windows 7, the serial port DB, RTS and TD lines are again defined as "HOT" (high voltage) by Windows.

Computer: Dell Optiplex 745
Windows 7 Pro 64 bit with SP1 installed
Serial port on motherboard: Intel ICH8/ICH8R LPC Interface Controller 2810
Serial driver: Microsoft 6.1.7600.16385 (is up-to-date)
```
   Settings for COM1:
   -------------------
   Baud Rate:     9600
   Data Bits:     8
   Parity:        None
   Stop Bits:     1
   Flow Control:  None
```
I spent hours looking at the Manager of devices/port settings and try to find anything online with no luck. Is it possible that this is because of the way Windows 7 plug-n-play manages the serial port? How can I turn it off then the port by default as if it was on XP and earlier versions of Windows is 'off '?

Thanks, Dave
Dave,

I can't believe that you have not answered this question. I had the same problem as you trying to control my radio interface. I just came by for a Dell Optiplex over the weekend and noticed the same problem. I was searching the Web for an answer when I found this post. I am happy to say that I found the solution to my Optiplex and how it works for you. I went into the BIOS and set the UART protection on. Makes no sense to me because I'm a software guy, only an amateur on the hardware side. I left the BIOS and the serial port works as it should like in XP.

Steve

Wireless Pan DHCP Server will not start... Error: Static Interfaces/Listening Ports not available

I had trouble not getting no connection with WiFi, after weeks of allsorts following advice on forums etc, I found that the Wireless Pan DHCP Server does not start with error: Static Interfaces/Listening Ports is not available. my understanding is that the ports UDP 67/68, but when I run a Netstat I don't see them in the list. I checked windows firewall and they seem to be set to DHCP.

Any ideas would be useful.

Win 7 Home Premium 64 - Bit SP1

Please post your request here:

http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

Change the listening port for SSH on IDS

Should what command I use to change the listening port on an IDS 4200 series? I listen on another port, and when I applied the S189/S190 update, it changed SSH port 22.

Just out of curiosity, too, no one knows what else S189/S190 updates change?

Thank you

Jim

Cisco supports only configurations using the CLI interface. The ssh port cannot be changed through the CLI. Modifying the files in config system via the service account is not a good idea and not supported.

Default connection ports

Hello everyone so I recently installed ESXI 6 on my proxmox server and used the ESXI embedded client host fling, which uses default authentication ports 80 and 443. My question is how I would go about changing ports Auth to something such as 8080 and 8081. The reason why I want to do it is because it is a test for Learning Lab and want to access remote web control panel. I looked Configure a VPN, but I prefer to forward a port 8080 or 8081 and access it that way. I am aware that this question has been answered before but it has been 5.0 and 5.5, which uses proxy.xml which has been deleted in what concerns or move to the 6.0 because I'm not. If this has been answered elsewhere I apologize.

Hello

You may need to modify /etc/vmware/rhttpproxy/config.xml file in 6.0 (as per article VSphere 6.0 Documentation Centrepubs)

There is also an exchange of views about this in Re: Proxy.xml that allows us to modify to enable HTTP for vSphere SDK is not found in ESX server 5.1

Thank you

Muruli

APEX does not open after you have created the new Oracle listening port
Hi guys,.

I had to re register Oracle listener using "lsnrctl start". A new listening port has been created and I am able to connect user Apex by PL/SQL Developer. Port 8080 is open.
But if I try to open the application APEX of URL (http://localhost: 8080/apex/f? p = :::) 4550:1:0 its not opening not.) It was working fine until yesterday.
I use Oracle XE 11 g and APEX 4.2

C:\Windows\System32 > sqlplus sys as sysdba

SQL * more: Production of liberation 11.2.0.2.0 kills may 7 22:21:18-2013

Copyright (c) 1982, 2010, Oracle. All rights reserved.

Enter the password:

Connected to:
Oracle Database 11g Express Edition Release 11.2.0.2.0 - Production

SQL > SELECT DBMS_XDB. GETHTTPPORT FROM DUAL;

GETHTTPPORT
-----------
8080

SQL >

so I do not know why APEX does not URL. What I have to put something at the TOP after you have created the new listening port. Can you please help?

Kind regards
Marie Claire

Published by: 1004608 on May 7, 2013 14:40
Link to your thread to listen would have helped: Oracle XE 11g with Apex No problem of Listener (ORA-12541: listener TNS:no)

It seems that your listener uses the static instance via the listener.ora file registration and missing entries for the http service. Edit your listener.ora (F:\Apex_Installed\app\oracle\product\11.2.0\server\network\ADMIN\listener.ora) file and add the following entries in the listener.ora file DESCRIPTION_LIST. Then, restart the listenerer.
```
(DESCRIPTION=
  (ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=8080))(Presentation=HTTP)(Session=RAW)
)
```

Remote listening port
Hi all

I have oracle 11g rac ASM in RHEL5
I have 2 nodes
node 1 VIP 115
node 2 VIP 116
for each of these nodes, I local listened as oracle said, I also have remote listener
witch is listen to these two nodes and do the load balancing and my remote interlocutor is set to SCAN ip like oracle

My question is:
the remote listener is resident in what node because I found the listener even also reside remotely in nodes 1 and 2
When the connection is came to the listener (distance) of the database is also detect that new connection is coming and then
to see which node is have less load and pass this connection to the local listening port, so I need to know the remote listener
reside in the nodes 1 and 2 or... I don't know?

Thank you very much
crsctl State resource t
This will show you the current locations of all resources, including your listeners SCAN.

default listening port no

Similar Questions

Maybe you are looking for