Dell E7440 i5 4310U 16 GB of the RAM upgrade question

Similar Questions

• Reference Dell 4600 ram upgrade questions

  a crucial site for dell 4600 scanner and ram orderly and upgraded from 256 and added 2 512 sticks.  When I restarted I got a message that the operating system supports no more than 256 MB of ram on a 32 bit...?  Owner's manual says I can go to 1 GB.  Tried to use only the 2 512 taking the 128 (in cracks) but get the same message.  Geek squad checked the ram and agreed it is of the appropriate type, but something may need to be updated in the bios? What to do?

  
  

• Problem with the ram upgrade.

  

  I have a laptop DV4-5100 and I received the new ram for it, but there is no way for me access to the ram compartment, apparently there is no screws or anything to open. So exactly how am I suppose to upgrade ram?

  You should be able to drag the yellow locks for the compartments and remove the panels.

• 13 - a071ng: problems with the RAM upgrade - where is the crack?

  Hey there,

  so today I got my new x 360 a071ng HP. I wanted to upgrade my RAM from the standard 4GBs to 8GBs and replace the HDD with a SSD.

  Replace the HARD drive has been frank and I have not encountered any problems. But there is a problem: I can't find the slot of the RAM.

  The HP website is not saying something about a RAM memory that can be removed and nor does the Crucial site that actually says that there are two available slots.

  -Is anyone can help me? Is it hidden somewhere? Perhaps under the motherboard or the battery? Or is the site condition information simply false and there is no way to upgrade the RAM?

  Best of the Austria,

  Jannis

  Here is the Manual:

  Manual

  See Page 49. Memory access requires the removal of the motherboard I hate to say but if you on the hard drive, you were close. Just pay attention that HP will not honor the warranty if you damage the laptop in the process. Good luck and post if you have any other questions.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• EliteBook 9470 m stops after the Ram Upgrade

  Hey guys
  I bought 2 Kingston 8 GB of Ram for my HP Elitebook Folio 9470 m (Windows 8 Pro) be upgraded to 8 GB to 16 GB. According to "Memory search" of the Kingstons the RAM I bought should work with my laptop:

  Module 8 GB - DDR3 1600 MHz

  Weight: KTH - X3C / 8G

  Yes, it should work. I checked the site of Kingston and memory is specifically recommended for your model. I try every Kingston module separately with the HP module and run a comprehensive test of memtest on it.

  http://Memtest86.com/download.htm

  Create a bootable usb stick with memtest cd and run it on each module. I suspect that you got a bad stick of RAM. At least if it doesn't not Kingston is very reputable, and they will refund your money.  This is proposed by Crucial memory:

  http://www.crucial.com/search/searchresults.aspx?keywords=EliteBook%209470m

  If that's the answer you need, please click on accept as Solution so that others can find it on the road.

• The Task Manager does not recognize the ram upgrade

  Hello HP community!

  Well, it seems that I have a problem with my ram upgrade. My system came with 2 GB of ram, and I had to upgrade (with another 2 GB), I am using programms like autoCAD, 3dsmax, photoshop, etc who have special needs on the RAM. Here's the problem; While the bios memory being recognized (4096 MB), what the task manager of the total physical memory is only 2046 MB! I also did the update to the BIOS, but it didn't work. The new memory I plugged in has the same features with one installed. The only difference is the manufacturer, the new is Kingston.

  Here are the characteristics of my system;

  Operating system installed: Windows Vista 32-bit

  Product name and number: HP Pavilion dv7 - 2030ev

  • Motherboard: Quanta 3624 intel PM45 (supports up to 8 GB of ram)
  • CPU: Intel Mobile Core 2 Duo P8600 2.40 GHz (64-bit Architecture)
  • RAM: 2 GB DDR2 PC2-6400 800 MHz 6.0 CASE Samsung latency
  • BIOS: F.46

  The RAM I bought is:

  Latency CASE of Kingston DDR2 PC2-6400 800 MHz 2GB 6.0

  (The package information to be exactly: KVR800D2S6 / 2GB PC2 - 6400 CL6 SODIMM 200 - Pin)

  I also mention, I tried the only Kingston on a Slot and the system worked without any problems...

  I would be so grateful if you could help...

  Thank you in advance,

  Nick Chatzikonstantinou

  Hi, Nick:

  One of our experts at the top of the forum (DavidPK) page suggested that you look at this solution to the question of memory you meet...

  I quote David:

  "In the system startup tab Configuration screen, the Advanced Options, it proved that there is a check mark in the maximum memory box.  Once removed and the applied change, Windows recognized all the Ram (less the reserved) after the reboot. »

  If please give than to try and post back and let us know if that frees a memory system for you.

  Paul

• Dell PowerEdge T110 is not using all the Ram installed

  Hi, my name is Juan Marrero.  I work for bike Stop, Inc. in Puerto Rico.

  I've recently upgraded the processor and RAM to our PowerEdge T110 server.  Initially, there were only 4 GB of RAM.  Now he has installed 16GB but only 8 GB are usable.

  The processor is an Intel Xeon x 3430 and has been upgraded to an Intel Xeon x 3470.  No problem here.

  The specifications of the memories are: 4 GB DDR3 PC3 - 10600 ECC Unbuffered DIMM (4 of them)

  for a total of 16 GB of RAM.  I searched the internet and found nothing in the BIOS to not limit to 8 GB.

  Is there a limitation, no matter what the motherboard and processor say they can handle?

  I thought. The Foundation is limited to 8 GB:

  https://msdn.Microsoft.com/en-us/library/Windows/desktop/aa366778 (v = vs. 85) .aspx #physical_memory_limits_windows_server_2008_r2

• Correct procedure for the Ram upgrade.

  Dear Sir, I recently bought a laptop from HP 15-r074tu,

  It comes preinstalled with a 4 GB of Ram. I want to upgrade to 8 GB.

  I don't know where I should achieve this. I should get this done @ the store where I bought it?

  Or do I have to reach out to a HP's Service Center. Just so it is not void the warranty.

  Can someone kindly shed some light and enlighten me.

  Thanks in advance.

  Hello

  Here are the details given below for the upgrade of memory also attach the manual link given below for your reference. Check replacement for the component numbers 73 procedures page & 1 Page for more information on memory.

  Memory
  housing for module customer accessible/upgradable memory 1 or 2 (depending on model)
  2 slots: DDR3L - 1600 MHz Dual Channel Support (Core processors)
  1 location: DDR3 1333 MHz Dual Channel Support (DDR3L-1600 demoted to the)(Bay Trail) DDR3-1333
  processors)
  1 location: DDR3 1333 MHz Dual Channel Support (DDR3L-1600 demoted to the DDR3-1066)(Bay Trail)
  processors)
  Supports dual-channel memory
  Supports up to 8 GB of RAM in the following configurations:
  8192 MB total system memory (8192 × 1.) or (4096 x 2)
  System memory total 6144 MB (4096 × 1 + 2 048 × 1)
  Total system memory of 4096 MB (4096 × 1.) or (2048 x 2)
  Total system memory of 2048 MB (2 048 × 1).

  Spare part number : 8 GB (PC3L, 12800, 1600 MHz) 693374-005

  Manual link

• The RAM upgrade will void the warranty?

  Hi guys,.

  Just a question, I just bought a HP laptop. I want to add another 4 GB DDR3 stick. Would that void the warranty?

  Thank you!

  Hello

  No, it will not void your warranty.

  Kind regards

  DP - K

• The NAC upgrade question

  I intend to improve our systems SCS and CAM version 4.6.1 to 4.7.2. The documentation states that "Cisco recommends that you do not perform this procedure to upgrade via an SSH connection, because the steps needed to restart the appliance during the upgrade process will cause your lost connection."

  Is the only concern with the help of SSH that you will lose your connection and the need to reconnect (and possibly miss some messages in the console), or is there something in the upgrade, which can be a console connection?

  My CASE systems are 65 miles away and forced to dig between locations will increase the window for a potential failure.

  We met our CAM and ea 2. CASE until 4.7.2 with SSH only, no access console. Not always the best idea (in this case for some reason you NEED it), but it can be done completely via SSH for orders and SCP for file transfer.

• Most bang for the buck upgrade question

  Hi all.  I am currently using VMWare Workstation for Windows v6.x and have noticed that when I have three open tiles, my machine seems a little slow.  Current specifications are:

  CPU: Intel Core 2 Duo E6750

  RAM: 8 GB

  OS: Vista Ultimate (64-bit)

  OS disk: Velociraptor 150 GB

  VM disk: 1 GB Western Digital (all VMs are on this drive)

  SMV (RAM): SCO UNIX (512 MB), Windows XP Pro (2 GB), Windows XP Pro (1 GB)

  My question is the following, which would give me the best bang for my money:

  1. Upgrade to a Q9550.

  2. Allocate more RAM for the virtual machines (I currently use about 6GB with all the tiles running and what Vista takes on the host)

  3. Build a new machine with an i7 processor.

  4. Move virtual machines to a single Velociraptor.

  5. Move virtual machines to a RAID0 array (using two drives of 1 GB / 7200 RPM).  I know THAT RAID-0 has no redudancy; I would be back up critical files to an external drive of 1 GB.

  On these machines, I do some scripting/small database unix (SCO VM) and especially the word processor (several documents) / some work with audio products/editing Adobe (WinXP VMs).

  Thank you, in advance, for your input.

  I would like to start with more and faster for the VM disks.

  ___________________________________

  VMX-settings- VMware-liveCD - VM-infirmary

• PS the victory to the Mac upgrade question

  I'm moving from windows to mac.

  my windows serial number does not work on my mac to PS cs6.  He did for LR4.  Why, what I can do.

  Thank you.

  It's because your license of Photoshop CS6 is Windows only.  Lightroom has a cross-platform license, that's why you were able to install it on your Mac with success.

  Please see product order | Platform, language Exchange - l http://helpx.adobe.com/x-productkb/policy-pricing/order-product-platform-language-swap.htm for more information on how to request a Mac from Photoshop CS6 version.

• SE error message: Windows has not start because the following file is missing or damaged. Windows root\system32\hal.dll, after removing the RAM

  Original title: computer \sysytems32|hal.dll shows this when starting. Old dimension 2350.

  I tried to install McAfee Total Protection on an old Dimension 2350 and after that computer system has been slow and useless. After the call of Mcafee, they told me my RAM was too small at 640 MB and said if necessary to upgrade to 1 GB. I called Dell and they wanted to know that the RAM so had to remove it. After removal and reinstallation of the computer, but I got the error above.

  I have the reinstallation windows xp cd drive professional service pack 3, but can not get beryond this message options

  Hi gfritz1,

  You can consult the following Microsoft KB article and check if it helps:

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  http://support.Microsoft.com/kb/314477

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Hardware RAM in Question 8 or 16 gig? for the treatment of LR3

  My old P4 XP with 2 gigabytes of RAM works yet, but any serious change in LR is slow... All the problems of performance aside, I thought I would ask a question that I know is a little subjective or maybe even stupid...

  I'm looking at a Dell XPS8199 i7 processor 64 but but the

  My Question is ... Anyone think that is worth command with 16 GIG RAM compared to the standard default value of 8GIG of RAM for LR3 treatment/CS5M?  It will run to $360 ...   All comments are welcome...

  The problem I had in the past is that the 8GIG is 4 2Gig DIMS and later to upgrade it will cost you much more I have to put in 4 4gig DIMS (I think... I'm not a tech guy at all)...

  The only way my old P4 has lasted is because of the years memory upgrade but it costs me... so I think I should just go with a lot at the start...

  Core i7 material uses DDR3 triple channel memory. Three DIMMs in channel A, B and C & will run significantly faster than the 4-6 DIMMs. The relative speed difference is kind of 25-26 with three 17-18 with 4-6 vs.

  Your best compromise is DIMM for 12GB 3x4GB.  That's what I'm running in mine, which is a lot that LR currently does not use everything. I've seen the use of ~ 5.5 GB max in my bench of 6 hearts.

  Also, there are more fast & slow DIMM, check their clock speed & record timing. In addition to clock speed (1333, 1600, 2000, etc. best) latency also factors in. 7-7-7-24 are better (and of course more than $), 9-9-9-24 is slow but usually cheaper. Of course also depends on the speed of the i7 processor and motherboard / BIOS capacity. Some systems may if run at higher at a time of increased latency clock speed lose all or part of the advantage of clock speed.

  I wish life were simpler...

• Do I have to pay to download the driver for my printer Dell 966 all in one I lost the driver CD?

  Original title: Dell Printer 966 all in one

  Do I have to pay to download the driver for my printer Dell 966 all in one I lost the driver CD?

  Sam Soliman
  E-mail address is removed from the privacy *.

  You shouldn't if you get it from Dell.