Dell inspiron n5010 screen turns white

Similar Questions

• Replace screen Dell Inspiron N5010 5521

  Hello

  I had 3 vertical lines on the screen of my Inspiron 5521, I have also Inspiron N5010 that has fried motherboard, but his screen was working the last time I tested. Can I use N5010 screen to replace the screen of the Inspiron 5521?

  Hello

  Unfortunately, Inspiron N5010 screen is not compatible with the Inspiron 5521, or vice versa.

• Dell Inspiron N5010 8 beeps on start up

  Hello

  I have a Dell Inspiron N5010 and it fell out of my bed, since, then it stopped working. Whenever I try turn it on it beeps 8 times in the series.

  I went through various discussions in dell community in this regard and have done the following tests.

  Test of LCD (D + market) : this test runs fine, able to see the colors strong and when restarted, it gives again 8 beeps

  FN + market : it does not work. I have seen in discussions, this should run a diagnostic test. But in my case, nothing happens, 8 beeps continues.

  A few posts proposed to remove the CMOS battery for a while and place it again. Who did too much work.

  Reconnect the cable to the LCD screen and try, problem still exists.

  Can anyone suggest me what might have gone wrong?

  Thanks in advance.

  Then to do is replace the video cable - if this does not resolve the problem, it's probably that the motherboard has been damaged in the fall.

• Dell inspiron N5010 stops when starting in 10-15 seconds

  I am facing some kind of problem with my Dell inspiron N5010 laptop. Whenever I take my laptop to some place let home College will stop start, when I turn on my laptop it starts but after that 10-15 seconds it stops, also when I try to keep the system in the bios it still stops within 10-15 seconds.

  Twist in the problem, is that if I keep my laptop idle for 20-30 minutes, it starts to work fine (I never remove battery or just left my laptop ram idle)

  Another thing is that I face ths portable computer wheonlyn problem is done by me in my backpack or you can tell when the laptop is subject to movment.

  I've noticed this trend seriously. For 15 days I did not move my laptop on my desk and it works like any normal laptop computer, but today when I took it to my place of friends, and when I tried to start it it starts and stops within 15 seconds while the startup I've done the same left witouth slowed even kidnapping ram or battery or charger for 10-15 minutes and then it starts to work very well.

  Why is this happening, it is there is a problem I have material or just a bad connection.

  Hello

  I have the same dell inspiron n5010, which stops immediately when turned on. doesn't even go beyond the DELL welcome screen! All my attempts to clean the fan/vents and reapply the thermal paste on cpu/gpu dint solve the problem, more than doubling the cpu/RAM/HDD. Also disconnect all mainboard modules like hard disk, dvd, wifi/Ethernet, sd cards and leaving naked force mainboard solves the problem. Conclusion; MOTHERBOARD IS DEAD! RIP

  Technicians will eat your money and some even miraculously make it work but the problem is still there and of course that the night will come back! REPLACE THE * BOARD OR GET NEW!

  #NOTBUYINGDELLEVERAGAIN

• 11 - e010nr after the signature on the photo and a few icons appear and then the screen turns white and reappears

  Laptop TouchSmart 11, e010nr 11, windows 8, no error message. I can Ctrl/alt/del and obtain the lock... the Task Manager screen. This screen works but nothing else

  Hi danny61,

  Just to clarify , when your screen turns white and reappears, the icons reappear also? and do you not see that set the desktop background or the taskbar? that it could be as simple as restarting the Explorer process in the Task Manager.

  If you can update me if I can see how I can help

• Dell inspiron n5010 laptop computer running XP, when I try to open my software programs including Internet Explorer, they hang and Manager tasks indicates "not responding".

  I have a dell inspiron n5010 laptop and when I try to open my software programs, including Internet Explorer / Outlook Express they partially open but not completely open and just hang out there. When I go to the Task Manager, I get a message 'not answer' for the program. I then started the pc using F12 and got the error OFOO C. 133 talked to Dell and they tell me that it is a Windows 7 problem. Can someone help me with this issue please!

  Separated from the:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-files/Inspiron-15-XP-laptop-getting-error-code-0f00133c/fd3d76ad-Ca4a-4830-9ef1-17ccb9a7d9f4

  Hello

  1. did you of recent changes on the computer?

  Method 1:

  It is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  Method 2:

  You can also try the steps of troubleshooting provided in the link below to fix the problem.

  Computer stops responding with a black screen when you start Windows XP

  http://support.Microsoft.com/kb/314503

• P2412H - displayed briefly and then the screen turns white.

  Hello

  I got a pair of monitors of P2412H little more 3 years, bought from a dealer - I don't have tags and monitors say manufactured in September 2011 (so I think that, apart from any warranty).

  This morning one of them has failed - it displays briefly, then the screen turns white.

  Manual test:

  1 unplugged every wire and power button which is held for 15 seconds.

  2 reconnect the power cord.

  -Switch will blue

  -L' initial Dell boot screen is displayed on the screen for less than a second.

  -L the screen turns white.

  -Stays blue power button

  3. press one of the control buttons

  -Nothing happens

  4. disconnect the monitor

  5. connect the monitor to on PC with Windows connected using DVI.

  6. connect the power cord

  -Switch will blue

  -L' initial Dell boot screen is displayed on the screen for less than a second.

  -L the screen turns white.

  -Stays blue power button

  I also tried to reset the monitor according to the instructions of the manual by pressing keys 1 and 4, but as the monitor does not appear, I couldn't see anything.

  The monitor did briefly revived properly after one of my attempts back manually, but the after turning on and the new to check if the problem itself had set the monitor returned to the not displaying no not again.

  Can anyone help or point me in the right direction on how to fix it?

  Thank you

  * UPDATE *.

  Disassembled the monitor I've used this as a guide to youtube to open the monitor the safely:

  cs_setInnerHtml ('video_aebd897a-01ed-42eb-a8c5-b3b6ecee6556', ");

  Inspect the circuits printed for all the obvious problems such as cracked soldering or fried capacitors.

  Could not see the obvious problems... you realign a couple of back vertical capacitors where some of them were in sharp corners appeared to be very close together as a result.

  Back together carefully.

  Backwards and now it works very well for 48 hours.

• You need to reinstall Win 7 Home Basic which entered the pre-installed on Dell Inspiron n5010 laptop.

  Hello

  IAM using dell inspiron n5010 Lapop
  who came from Windows 7 Home Basic... I could not find my product key during that...
  later I installed trial windows 7 ultimate... so far I'm used it...
  now, I would like to install pre installed win 7 Home basic... How can I do that... now I dnt have any restore disk, is it possible to take recovery media...
  help & offer me please someone...
  Thank you & best regards
  Vinoth
   
  Original title: pre installed os to format

  Hello

  With a DELL, you press F8 to start the process of recovery/reinstall to Windows 7.

  CTRL + F11 is for DELL computers that took place of XP.

  "How to restore your Windows 7 computer to factory settings.

  http://www.Dell.com/support/troubleshooting/us/en/04/KCS/KcsArticles/ArticleView?docid=DSN_362066

  restore your computer Windows 7 settings

  1. Back up important files and data. If you do not back up your files, you will lose them.
  2. Turn off your computer.
  3. Disconnect everything but the monitor, keyboard, and mouse. This includes your:
     • Scanner
     • printer
     • modem or network cables
     • mobile phone and Tablet
     • Another external hard drive or USB flash drive
  4. If your laptop is docked, remove it from the docking station.
  5. When the Dell logo appears, press F8 to open the Advanced Boot Options.
     Note: If the Advanced Boot Options menu does not open, wait for the Windows login prompt. Then, restart the computer and try again.
  6. Use the arrow keys to select repair your computer and press enter.
  7. In the System Recovery Options menu, select a keyboard layout and click Next.
  8. To access the recovery options, log as long as administrator, and then click OK to open the Dell Factory Image Restore.
  9. Depending on your configuration, you may need to select Tools Factory Dell , then Dell Factory Image Restore.
  10. Click Next to open the menu to confirm the deletion of data.
  11. Select the Yes, reformat hard drive and restore the factory State system software and click Next.
      Note: The restore process begins and may take five or more minutes. A message appears when the operating system and the applications installed in the factory have been restored to the State of the plant.
  12. After the restore operation is completed, click Finish to restart the computer.
  13. Restore all data or programs that you want to back up files.

  See you soon.

• Re: NB200 - making noise and the screen turns white

  Hello

  My laptop makes the high pitched noise and the screen turns white. Please help with this question.

  Thank you

  Hello

  It is especially as this problem with the inverter. She is, die, and made a noise of pitch. Try to connect the external monitor and check if it is displayed.

  Welcome them

• Satellite L300 PSLBGE screen turns white after a while.

  I * model Toshiba Satellite L300 PSLBGE * and I have never seen this problem before.
  I use my laptop since last year in fact my laptop screen turns white after spending some time on it, usually after 10-15 minutes...

  sound also stop here and the only solution is to reboot, after that reboot it still works well, but after a while once again its screen turns white.

  Please help for this problem

  Post edited by: bharatjaiswal5

  Hmm have you tried to reinstall / recover the laptop to see if it helps to solve this problem?
  In my opinion you should try it because it could be a problem in the system.

  Otherwise if new system installation / restore does not help you, it could be a malfunction of the equipment.

• When I turn on my emachine and try to check my e-mail, I get my homepage to google for about 1 second and then the screen turns white with bee.pl.

  HELP me get my E mail.

  When I turn on my emachine and try to check my e-mail, I get my homepage to google for about 1 second and then the screen turns white with bee.pl.

  http://INFOTEP.bee.pl/info.php?avted=;     I'm not that day on computers, and many of their functions and a few times I get a little lost in there so if anyone can help me I really appreciate it.    Thank you!!!

  Hello

  1. what operating system do you use?

  2. What mail client do you use?

  3. you have made any changes to your

  4. what site you're talking about?

  5. How do you access the webpage?

  6. you use Internet explorer or another browser to access the site?

  The link give http://infotep.bee.pl/info.php?avted takes me to a blank Web page

  Are you referring to http://www.bee.pl/index

  Refer to the following, who says that the sites host malware

  http://www.Google.com/SafeBrowsing/diagnostic?site=monidopo.bee.pl/

• When trying to view videos full screen, the screen turns white!

  When I try to watch videos, I love to watch full-screen, but when I press the icon full screen the screen turns white. I have to press the ESC key to return to normal. What will fix this?

  i right click on video > select settings > remove the check mark from material

  Acceleration.
   
  II] download and install: -.
  Adobe flash player: -.
  http://www.Adobe.com/products/flashplayer/
   
  III] update your graphics card driver on the website of the manufacturer of the graphics card.

• Restart computer, windows xp screen came then the screen turned white

  Restart computer, windows xp screen came then the screen turned white

  Hello

  1. have you made changes on the computer recently?
  2. do you get an error at startup of the computer?

  Check to see if the problem exists in Safe Mode, if the computer works as expected in mode without failure, then we can solve the problem in the clean boot state.
  a. refer to the article below for the procedure safe mode in Windows XP
  A description of the options to start in Windows XP Mode
  http://support.Microsoft.com/kb/315222

  b. you need to perform a clean boot to find the program that is causing and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  I hope this helps.

• my Dell inspiron n5010 is unable to use an ip address to connect to the internet?

  my Dell inspiron n5010 is unable to use an ip address to connect to the internet? and I went into Device Manager > network adapters > then I face three options 1 > virtual broadcom wireless adapter > DW1501 wireless-n WLAN half mini card > Microsoft virtual WiFi Miniport Adapter that should choose?

  Thank you very much

  Hello big evil Dossary

  Follow the steps to connect to a form of wireless link below. Thank you.
  http://support.Microsoft.com/kb/928429

• Problem with drivers WLan on Dell Inspiron N5010

  I recently bought Dell Inspiron N5010 laptop, however, there seems to be a small problem: impossible to get WLan drivers installed.

  I use Windows 7 (x 64 Edition). On the Device Manager under "Other devices" there is an unknown 'network controller '.

  Tried to install the drivers for Dell drivers & downloads section (Yes, I used my serial number), but there was a problem with the following:

  -R252544 for Dell Wireless WLAN 1520 half minicards. Result: "no compatible hardware found. The software you are trying to install is not supported on this system. The software will not be installed. "Half Mini Card

  -R247430 for link Intel (R) Intel WiMAX 6250. Result: "this software package cannot be installed on your system."

  -R252283 for Intel Intel(r) WiFi Link 6200 "no compatible hardware detected. The software you are trying to install is not supported on this system. The software will not be installed. »

  All these messages to appear just after you run the Setup program. Other drivers have been installed successfully and in good order.

  I assume you have three possibilities: -.

  (1) you can visit http://supportapj.dell.com/support/downloads/index.aspx?c=in&l=en&s=gen and make the right choices...

  or

  (2) visit the support section of the material suppliers Web site (it's Broadcom Corp.)

  or, if even this does not solve your problem;

  (3) install software like Driver Genius Pro... that would solve all hardwre driver problems related with certainty at 100%.

  Hope I helped solve your problem...