DHCP IP use connected vrf

Similar Questions

• No dhcp use connected vrf ip

  Hi experts,

  I would like to know what this command does? I can't found on cisco.com.

  Hi John,.

  This command indicates the router if requests from DHCP directly connected interfaces VRF to allocate IP addresses from a global DHCP pool (which is not specifically related to any VRF), or if a DHCP by VRF pool should be used to assign addresses.

  Consider the following configuration:

  IP vrf MyVRF1

  RD 1:1

  !

  IP vrf MyVRF2

  RD 1:2

  !

  Global IP dhcp pool

  192.0.2.0/24 network

  !

  dhcp ForMyVRF1 IP pool

  VRF MyVRF1

  192.0.2.0/24 network

  !

  dhcp ForMyVRF2 IP pool

  VRF MyVRF2

  192.0.2.0/24 network

  !

  interface Fa0/0.10

  encapsulation dot1Q 10

  192.0.2.1 IP address 255.255.255.0

  !

  interface Fa0/0.20

  encapsulation dot1Q 20

  IP vrf forwarding MyVRF1

  192.0.2.1 IP address 255.255.255.0

  !

  interface Fa0/0.30

  encapsulation dot1Q 30

  IP vrf forwarding MyVRF2

  192.0.2.1 IP address 255.255.255.0

  With no dhcp ip use vrf connected, if a query DHCP comes which interface here, he will be assigned an IP address of the overall global DHCP pool, with no regard for the VRF the interface through which the request is entered in. DHCP VRF ForMyVRF1 and ForMyVRF2 pools will remain completely unused and intact, although only being defined.

  With the dhcp ip protocol use the vrf is connected, the behavior becomes what you would normally expect-Fa0/0.10 requests will be served DHCP Global pool, the requsts which crosses the Fa0/0.20 in MyVRF1 VRF will be served by the DHCP ForMyVRF1 pool and Fa0/0.30 requests will be served DHCP ForMyVRF2 pool as the Fa0/0.30 is assigned to the MyVRF2.

  Best regards

  Peter

• I put my cRIO 'DHCP' to 'local connection' and lost contact with her.

  I put my cRIO 'DHCP' to 'local connection' and lost contact with her.

  I changed the location setting labelled '2' to post a link-local only, so I think I hit save to '3 '.  So, I have had no contact with my cRIO network.

  I tried;

  Hit the reset button

  A MAX of opening closure

  Go to safe mode

  Lift the switch to reset IP

  Power cycling the cRIO

  Directly from the host to my target of cat 5 cable running

  None of it worked, and I have no contact with my cRIO.

  

  This is what MAX looks like now.  How can I fix?

  

  It turns out that I had more of a problem.  Corrupt drivers, 255 in many in my subnet mask, overly complex LAN, use server control... you get the idea.  So I just deleted all software, disassembled everything and more from scratch.  Now back to the top and work.

  Thanks for the tips everyone, all the pieces and peace where it is useful to help me see the bigger picture.

• On the Sync Palm m500 using connection series with a dock under Windows 7

  Palm: m500

  Link: Serial (cradle)

  OS: Windows 7

  Problem: Palm Desktop 4.1.4 cannot be installed and does not synchronize Palm Desktop 6 using the serial connection.

  How can I synchronize the m500 using connection series with a version of PD under Windows 7?

  Nevermind, helped http://forum.brighthand.com/sync-windows-palm-os/261651-synching-legacy-pim-databases-palm-desktop-v-6-2-a.html .

• Anyone used Connect for people to vote on mobile devices together in the same room?

  I'm looking at the possibility of using Connect for in public voting room using the app to connect. Please let me know your experience of the present. How many devices you have used and how bandwidth is dealing with it.

  Thank you very much

  Peter

  Peter,

  Answer here: Adobe Connect user community

  Also, did you consult the Technical Guide 9 connect? There estimates of bandwidth for most of the features in connect.

• If a PC with a DHCP server is connected via VPN, with her serve IP addresses on the tunnel?

  Situation: we have a few portable computers test Ubuntu running DHCP servers.  We need get the updates and other changes in corporate network sometimes.  Today, we turn off the DHCP server, set up to get an IP via DHCP (besides) and make our updates.

  Problem: we do not want someone accidentally connect the laptop to the corporate network, while its DHCP server is running.

  Question: so, if we go via wifi using a Cisco VPN client, the DHCP server IP addresses above the tunnel?

  Thanks for reading.

  N ° DHCP uses layer 2 broadcasts to disseminate IP addresses.  Because your clients are connected via VPN, there is no contiguity of layer 2.  The only way he would accidentally do it is if you have configured an address to support IP dhcp as one of your VPN clients on the network, which I imagine you wouldn't.

• Your current settings of Firefox might make it difficult to use connection Notifications.

  I get this in facebook, when I tried 2 activate Login Notifications and im having trouble with the chat, I have 2 update the GET pg 2 the answer when I post a cat

  Just connect from a mobile device and change this setting if its still does not not on a desktop or laptop computer. I had the same problems with Firefox, Google Chrome and IE, which I don't yet use.

• uninstall the wireless printer. Try to install using connection USB installed on a network.

  Try to install HP Officejet 6500 wireless by using the USB connection. Installed on a network.  How do I uninstall and let Windows identify as new material on a USB connection?

  Turn off the broadcast of your wireless router signal. Shut down the PC. Menu using the printer configuration to remove or change the SSID. Then turn the printer off and connect it to a USB port (this implies that all the necessary software has been installed). Now turn on the computer and turn on the printer. Once the printer has been detected the turn on your router.

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• Google-account for you using connect to the Application

  I develop a native blackberry application and I want the user to be able to connect with their google account, can someone help me?

  Hello

  Well, it is not difficult. You must use OAuth 2.0. There is a very nice google documentation here:

  https://developers.Google.com/accounts/docs/OAuth2InstalledApp

  You will need to register at Google using the developer console:

  https://console.developers.Google.com/

  Then you define an application ' name, obtain an application ID, secret,... Please check the first link I provided, it is really well explained.

  If you want, you have the code for my application that use oauth to get a token for XMPP chat & access to gmail, it:

  https://github.com/amonchakai/HG10/BLOB/master/src/GoogleConnectController.cpp

  If you have a code example...

• How to enable remote workers to use connection internet main office

  Hi all

  I just set up our new 1802 as our internet firewall and a VPN server easy and everthing works fine. The only problem is that connected VPN Clients cannot access the internet. It is a policy of companys that all traffic from remote users must be encrypted and send them to the central part, so split tunneling isn't? t an option.

  I added the addresses IP of SDM_Pool of remote to the NAT ACL and reasons workers that the ACL is used by some packages that generates my "IBM Sametime", and this traffic can be seen in the ip nat translation. But the destination in this packet is a local ip (172.16.17.x) network so that in the case of EIB a package that is not coordinated.

  My question is, what happens to packets encrypted once they are decrypted in the esayVPN Server (what are the dest a source ip) and how to configure my router NAT packets to the IFs - external IP, because it isn? t incoming traffic on the inside, that is configured as ip nat inside.

  Thanks for your suggestions.

  Matthias

  This should help...

  http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_configuration_example09186a008073b06b.shtml

  Please evaluate the useful messages.

• I wan to use connections cable and wireless with Windows 7.

  I use Windows 7. I have a wired ethernet connection, but also internal wireless.

  I want to be able to use both connections. I'm using VMware Workstation and it allows me to specify which adapter to use with the virtual machines. However, when Windows 7 detects there are two cables and wireless, it disables the wireless and automatically uses cable.

  How to use both?

  Hi Michael,

  Thanks for the reply. By the brand and model of the PC, I see that there is not a driver designed for Windows 7. Try installing the driver in compatibility mode. Is your problem with the virtual machines that you have running, the host computer, or both? If it's on the host computer and that you have installed the latest driver in compatibility mode for Windows 7, then it is probably a compatibility problem of driver/hardware that by default, this feature in Windows 7 works.

  I hope this helps! Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Cannot collect dhcp information using device-sensor for profiling.

  Hello

  I try authentication dot1x/MAB (there is no issue here), but I want to collect information dhcp devices requesting the IP address of the dhcp server to the profiling using the sensor in the camera (cdp collects on - no problem) but when I check for all device-sensor of the show # dhcp cache, there is no single entry for dhcp data.

  The dhcp server is on the switch where these devices attempt to access the network since then and this should be the case. However, I noticed the following I don't know if it is bound (from device-sensor #debug error)-same error appear with different X value.

  DSensor: NULL input physical interface, throw packetRejecting IVR Interface VlanX package

  I am more concerned about collection attributes now rather than send... !

  Dip-switch IOS: Version 15.0 (2) SE9

  any suggestions?

  A couple more questions:

  1. do you have active monitoring dhcp ?

  2. do you see links in the dhcp snooping database?

  Thank you for evaluating useful messages!

• Get the parts with very high level in a tree by using Connect by

  I have the following table:

  CREATE TABLE (Z_BOM2)has VARCHAR2(4 CHAR), B VARCHAR2(4 CHAR));

  Insert into Z_BOM2 (A, B) values ('A', 'B');

  Insert into Z_BOM2 (A, B) values ('A', 'C');

  Insert into Z_BOM2 (A, B) values ('C' ' d ' ");

  Insert into Z_BOM2 (A, B) values ('C', 'F');

  Insert into Z_BOM2 (A, B) values (', 'E');

  COMMIT;

  SELECT * FROM Z_BOM2;

  A	B
  A	C
  C	D
  C	F
  D	E

  A is basically a Parent and B is a child.

  I would like to input not valid 'E' and 'F' in a query and get only the parents of high-level both those who should be 'A' for both of them. Here's the query I use:

  Select SYS_CONNECT_BY_PATH (, "/") as a path, a, CONNECT_BY_ISLEAF AS worksheet b, level, CONNECT_BY_ROOT b top_level

  of Z_BOM2

  connect by prior a = b

  Start with b IN ('E', 'F');

  
  Which returns the following:

  / D	D	E	1	0	E
  / D/C	C	D	2	0	E
  / C/D/A.	A	C	3	1	E
  / C	C	F	1	0	F
  / C/A	A	C	2	1	F

  Why it not return the appropriate top-level parent?

  This isn't my request.

  It is:

  select cbr the_parent, a the_child_you_started_with
  from (select a, b, level, connect_by_isleaf cbil, connect_by_root b cbr
  from z_bom2
  connect by prior a = b
  start with b in ('D'))
  where cbil = 1
  

  She returns B and has

• start-work using connect-viserver hangs in powercli 6

  Hello

  Previously, I used powercli jobs to execute commands to invoke vmscript quite successfully in our workplaces 5.1 and 5.1.

  I'm testing these scripts in vSphere 6 with pwoercli 6 and am having some problems with the script.

  An example of the previous scripts that worked is as follows:

  -----------------------------------

  Start-job-name $vm - RunAs32 - PSVersion 2.0 - scriptblock {}

  Param ($vm, $vcentre, $GuestCred, $session)

  {if(!$Global:DefaultVIServer)})

  If (!) () Get-pssnapin. where {$_.name - eq "vmware.vimautomation.core"})) {}

  try {}

  Add-pssnapin VMware.VimAutomation.Core - ea 0. out-null

  } catch {}

  throw "could not load the PowerCLI snap."

  }

  }

  try {}

  to connect-viserver $vcentre - $session wa - 0 session | out-null

  } catch {}

  throw "Failed to connect to server VI".

  }

  }

  $TestGuestCredentials = "dir C:\. »

  Invoke-VMScript - VM $vm GuestCredential - $GuestCred - $TestGuestCredentials ScriptText

  } - ArgumentList, $vm, $GuestCred, $session, $vcentre | FT

  -----------------------------------

  Now, in powercli 6 using modules that I tried to edit the script as well as the previous option using addsnapin is no longer works:

  -----------------------------------

  Start-job-name $vm - RunAs32 - PSVersion 4.0 - scriptblock {}

  Param ($vm, $vcentre, $GuestCred, $session)

  If (!) () Get-Module-name VMware.VimAutomation.Core - ErrorAction SilentlyContinue)) {}

  . "C:\Program Files (x 86) \VMware\Infrastructure\vSphere.

  }

  try {}

  to connect-viserver $vcentre - $session wa - 0 session | out-null

  } catch {}

  throw "Failed to connect to server VI".

  }

  $TestGuestCredentials = "dir C:\. »

  
  

  Invoke-VMScript - VM $vm GuestCredential - $GuestCred - $TestGuestCredentials ScriptText

  } - ArgumentList, $vm, $GuestCred, $session, $vcentre | FT

  -----------------------------------

  Using the foregoing in powercli 6 that the work never ends.  It's as if the connect-viserver command causes a response that requires intervention and locks work.

  
  

  If I remove the connect-viserver in the work section - it full well.

  Any ideas would be very appreciated!

  See you soon

  Have you tried switching of warning messages via the cmdlet Set-PowerCLIConfiguration , the DisplayDeprecationWarnings parameter?

• Recommended minimum on the data store when free disk space you use connection vRanger 5

  I was wondering if anyone can tell me what the recommendation is on the left of free space on a data store. I use 5 vRanger connection to back up my VM to another physical server. As such, I will not take snapshots 'manual '. I'm not sure if vRanger connection, running on a separate server, creates additional files on the data store.

  I've read a few threads on this site and some are advocating to let free, 20 to 25%, while that of others, offer 10% left free may be sufficient. Is there an official number for this or if anyone can share valuable experince?

  Welcome to the community,

  I generally recommend to have about 20% of free space on each data store. However, this depends on the activity/writes to disk during backup. vRanger connection - as well as any other backup software - create a snapshot, back up the virtual machine and then remove / commit the snapshot again. This is necessary in order to access the virtual disk files. Usually the backups are made during hours, so snapshots should not grow too much. However, you must also take into account the fact that in the case of a mistake - if the snapshot cannot be deleted - it will grow until it is deleted manually.

  André