How to enable remote workers to use connection internet main office
Hi all
I just set up our new 1802 as our internet firewall and a VPN server easy and everthing works fine. The only problem is that connected VPN Clients cannot access the internet. It is a policy of companys that all traffic from remote users must be encrypted and send them to the central part, so split tunneling isn't? t an option.
I added the addresses IP of SDM_Pool of remote to the NAT ACL and reasons workers that the ACL is used by some packages that generates my "IBM Sametime", and this traffic can be seen in the ip nat translation. But the destination in this packet is a local ip (172.16.17.x) network so that in the case of EIB a package that is not coordinated.
My question is, what happens to packets encrypted once they are decrypted in the esayVPN Server (what are the dest a source ip) and how to configure my router NAT packets to the IFs - external IP, because it isn? t incoming traffic on the inside, that is configured as ip nat inside.
Thanks for your suggestions.
Matthias
This should help...
Please evaluate the useful messages.
Tags: Cisco Security
Similar Questions
-
How would enable remote desktop connection and asking for help?
How would enable remote desktop connection and asking for help?
Do you mean on this site? Sorry, but we don't do that. We do not have the software required to make the connection (it's too expensive to buy personally) and even if we did we would not get in this practice. We work by display.
If you mean for someone else to help you, here is the procedure: http://www.howtogeek.com/howto/windows-vista/turn-on-remote-desktop-in-windows-vista/.
I hope this helps.
Good luck!
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
How can I block xbox 360 using my internet in my house
Hi all someone please help :) my daughter goes to the line with his xbox and that is using my internet I would like to know how to block it because my pc don't move when she's playing a game online even if I tell him to get off I need to know how to block this thank you
Delete the network connection of the Xbox. Either find the Ethernet cord (it's a small grey thin wire at the back of the Xbox with a clip to hold it in place) or remove the wireless connector (the white thing with antennas on the back of the Xbox) as she connects.
If the Xbox is one of the newer slim models, the without wire is integrated, so I don't know what to do.
-
Train webutil functions. How to identify if the user uses native internet
Hello
I have a form with a few webutil functions. How can I determine if a user uses the internet with native form explore?
If a user with jinitiator uses forms, its ok, but when a user use native internet explore, he gets the bean orcle.forms.webutil.fileTransfer not found error. WEBUTIL_FILE_TRANSFER.getMaxTransfer will not work.
When the user is using internet explore native, I want to disable the webutil function before generating a file on the application server and then you download on a client computer.
IM using Forms10g and Forms10gR2.
Thank youyou have two different config sections for the two modes?
If so, you could put a value different to each of them in the otherparams tag and read than when running, or use the other gall env and set a variable with different values for each config in there and read it through TOOL_ENV.
-
Satellite L300D - how to enable remote assistance?
Hello
I just got a new L300D satellite and a friend of mine helped me to set everything up.I want him to be able to get the remote control on my computer if I need her help, but it was not possible for him to do. He did so that I can get the remote control on his computer of mine, and he used the excact around the same parameters to the opposite effect, but it works not hers to mine. It can access my computer enough to see what is happening but not enough to establish the 'remote desktop pad"(sorry if the word is not fair, I'm not used to the computer language).
I think if there should be any kind of internal special protection in my Toshiba which needs to be set aside for another computer to access my computer in its own right?
Please help me to know what the problem is, because I would really like the extra security, he can help by remote access if I need.
Greetings
Karima
The way I do it is with FREE software. have your friend go * www.logmein.com *.
There, he can download the FREE version and outfitting. They then you go on the same Web page and download the client software FREE, put in place the password. He can then see your computer when he login to his account on Logmein. It works like a charm.
Good luckJohn
-
Satellite L450-136 - how to enable the taskbar preview using Win 7
Sorry about this question, but it drives me crazy:
When I select anything on the task bar, I get only 4 colors, instead of a view of the page.
Cannot for the life of remember me how to change.Hello
This live preview of task bar should be available if Aero is enabled.
In order to check if the Aero theme is enabled in your caseOtherwise I would recommend this Microsoft troubleshooting Aero:
http://support.Microsoft.com/kb/976170/en-us -
How to enable the memory full use in Win 7 Pro 64 Bit OS
Hello.
I have a desktop with Win 7 Pro 64 bit and its installed with 8Gigs of RAM above, but when I check in the properties of the computer it shows only 8 GM installed and 3.86 inuse.
Can anyone suggest me how to get the memory of 8 GB in use. ?
Concerning
Ishaan
Why do you need to use all of your RAM?
Are you trying to find how to use "RAMDisk"? The link below is for one of the
software available. A search can find a free version.http://memory.Dataram.com/products-and-services/software/ramdisk
The first I've heard talk of RAMDisk was today in the thread below.
-
How to enable end users to use applications of the administrator
I'm quite new to the Apex.
As an administrator, I created the schema of the tables and demand.
After I created an end-user, but I have to do in order to allow the end user to use my application?
My end user got these settings:
The user is an administrator of the workspace: No.
The user is a developer: No.
The access development team: YES
If I try to start as an end user, I don't see the application I created as an administrator.
Could you help me?
Thank you!Please check your other thread :-)
I need a Council for the development of an application for different users
Jens
-
How to allow remote VPN Sessions to communicate
Hi all
I'm trying to understand how to enable remote VPN client sessions to communicate. For example, if my manager has been connected via VPN to the office and needed me to fix something on his laptop, I cannot VPN to the office and RDP into her laptop. Not sure if this can be done without pain.
A brief out of my config. Remote client VPN sessions work fine. It's only when I try to access other customer VPN sessions, is where I have a problem.
Thank you is advanced!
FW # executed sho
: Saved
:
interface Ethernet0/0
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 4.4.1.8 255.255.255.252
!
interface Ethernet0/2
!
interface Ethernet0/3
!
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
outside_in list extended access permit icmp any one
split_tunnel list standard access allowed 192.168.1.0 255.255.255.0
inside_access_in of access allowed any ip an extended list
outside_access_in of access allowed any ip an extended list
access-list sheep extended 10.10.10.0 any allowed ip 255.255.255.0
IP local pool vpn 10.10.10.1 - 10.10.10.15 mask 255.255.255.0
Global 1 interface (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 0.0.0.0 0.0.0.0
inside_access_in access to the interface inside group
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 4.4.1.7 1
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto-map dynamic inetdyn_map 20 the value transform-set ESP-DES-SHA
map inet_map 65535-isakmp ipsec crypto dynamic inetdyn_map
inet_map interface card crypto outside
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
crypto isakmp identity address
crypto ISAKMP allow inside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 21
internal vpnipsec group policy
attributes of the strategy of group vpnipsec
value of 192.168.1.5 WINS server
value of server DNS 192.168.1.5
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list split_tunnel
moobie.com value by default-field
type tunnel-group vpnipsec remote access
tunnel-group vpnipsec General-attributes
vpn address pool
Group Policy - by default-vpnipsec
vpnipsec group of tunnel ipsec-attributes
pre-shared key nope
!
Hello
You need to allow pool vpn split tunnel, here's what you need to do
split_tunnel list standard access allowed 10.10.10.0 255.255.255.0
same-security- allowed traffic intra-interface
Kind regards
Bad Boy
P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community
-
On the Sync Palm m500 using connection series with a dock under Windows 7
Palm: m500
Link: Serial (cradle)
OS: Windows 7
Problem: Palm Desktop 4.1.4 cannot be installed and does not synchronize Palm Desktop 6 using the serial connection.
How can I synchronize the m500 using connection series with a version of PD under Windows 7?
Nevermind, helped http://forum.brighthand.com/sync-windows-palm-os/261651-synching-legacy-pim-databases-palm-desktop-v-6-2-a.html .
-
How to enable the remote desktop on windows 7 because it is missing in system properties | tab use remotely.
I am running Windows 7 Ultimate edition with service pack 1.
I used to connect my mac via the desktop tool to remotely (2.1) on my mac to my pc windows 7.
Now, it does not. Check the services of windows 7 I have ensured that all the remote control * services are enabled, but I still do see the Remote Desktop option in system, under the remote settings properties.
Any help would be appreciated.
MasterJay1
Click Start, click Help, and then type this phrase in the search box:
enable remote desktop
Article 5 will have explicit instructions for the task.
-
How to enable a connection to SQL Denali remotely?
How to enable a connection to SQL Denali remotely?
Hello
Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the public on the TechNet site. Please post your question in the below link:
http://social.technet.Microsoft.com/forums/en-us/category/SQLServer
-
How to enable Lightroom to use offline
Hello
I need to know how to enable Lightroom to be able to use it when I am not connected to the internet. Traveling out of town, in a remote place, etc...
Hi reaglephoto,
Please see: offline Activation
Let us know if that helps.
Kind regards
Mohit
-
Exactly what it says on the Tin.
Why can't I connect to Firefox accounts to set up sync to my laptop? FF30 + keeps telling me how please enable cookies; cookies ARE enabled, and I already tried Safe Mode. This has happened since the new Sync has been set up, so I think that nearly 30 FF. I'm now up to 34 FF version and it still does not work. I was not able to sync from the "update".
Problem #1: Going to about: accounts and clicking the Get Started button Blue opens a blank screen. It's not even a prompt on the cookies. It's just empty. Screen attached.
It comes from before the modules are disabled. If they are disabled in Mode safe, we go to the #2 problem.#2 problem: I've skimmed a thread (https://github.com/mozilla/fxa-content-server/issues/1017) and I tried connecting to sync through accounts.mozilla.com instead, but if the screen does not turn white while the modules are always enabled, "Enable cookies" warning are as far as I can get. Go to about: accounts in Mode safe mode gives the same result. I deleted all my cookies and my cache, FF restarted several times with and without active modules and still nothing. I browsed this forum of support for similar issues, and while other people have the same problem, no other threads have been solved yet. Several later versions of FF, it is far too long for this question still unresolved... Screen attached.
I know where the Firefox Cookie Manager, and I have enabled all settings. I was even able to third party cookies (even though I shouldn't really because they are unnecessary). No difference. Screen attached.
I looked into: config and looked up the word 'cookie' in names, but even this is useless to me since I am not a programmer and so ignorant of what mean really all of these parameters. Screen attached.
I'm at the end of my rope here, guys. It has been for months. A year. Maybe more than a year. I don't even remember. I just got a new camera and I don't want to add all my Firefox information one by one. It doesn't seem to be a way to contact Mozilla directly, so... Someone help please...
Ensure that you allow cookies for the domain of the accounts.firefox.com if you are not allowing cookies generally or use the cookie setting 'Ask Me '.
You can check whether DOM Storage is enabled.
-
How to access Windows 8 PC on the Internet with remote desktop connection?
Hello
Can someone tell me how to access Windows 8 PC on the Internet with remote desktop connection?
I'm good with the software and I have used many Microsoft software since the 1980s. So I like Microsoft products, but since they have outsourced their tech support, you can't support quality even if you pay for it. I followed all the instructions in the Windows 8 will help about DRC setting screens, but I can't connect unless I'm on the same home network. Here are the details:
I have a desktop PC with Windows 8 Pro and I have authorized the DRC. I tried two settings in system properties:
- Allow connections to this computer remotely.
- That allow the connection of computers running Office remotely with authentication NLA.
I also turned on both private and Public Windows Firewall settings > allow an App or feature through Windows Firewall.
I have installation then DRC to my laptop with Windows 8 (standard edition, not the Pro version). I have a DRC using the full name of the computer and other DRC using the static IP address for my ISP Desktop connection.
I use the user account administrator Windows for connections of DRC of the laptop.
I cannot get this to work on the Internet from a location outside my house with another ISP connection. The only way it works if I'm uncomfortable with the laptop using the same network home.
I called Dell tech support and it is always useless and just a more aggravating waste of an hour to talk to their support of technique outsourced in India (who barely even understand English) and then they hang up the phone as it was supposed to be disconnected. I also called Microsoft support and lost more than an hour to speak to their outsourced tech support in the Philippines (and as support of the India, they hang up or 'disconnect' when they cannot answer your question and they go account learn you more about Windows while they do). U.S. tech companies use AMERICANS more for their technical support so their customers can get people who actually care about doing a good job and can actually understand English?
So if someone who knows using Windows 8 for DRC on the Internet has some tips, then it would be greatly appreciated.
Thank you!!
P.S. If anyone is offended by my comments about the ugly, incompetent, stupid providing "technical support" in India or the Philippines - Nevermind! You go ahead and waste hours of your time talking to some Morón in these countries, who barely understands English and then 'disconnects' the call when they know that you realize that they are clueless and have all the answers.
Take a look at no - IP.com or dyndns.com, and then use your host.domain:3389 of no.-ip/dynDNS or run RelaVNc SErver that is running on port 5900 by default. Server options allow you to change the port as well if necessary.
Maybe you are looking for
-
Quit Skype...
Please see attachment... I unchecked "start Skype when I start windows" in the General settings. And I just restarted the system and shows the Skype in the start menu. Please tell me why this is happening?
-
HP 1050a printer has no action the printer
I use printer 1050A printing fades. I am trying to clean the heads and to see the ink levels, but I have no printer hp "action of the printer. I used the updates but still nothing. No maintenance task, no printertoolbox. What can I do? Is there a dri
-
I just downloaded MOED photos my camera and now they are gone. I've looked everywhere. I do not remove them. They moved from my camera as well. What to do next?
-
my hp pavilion dv6 has an audio beats that has stopped working.
Hello, I have a pavilion dv6 notebook pc and I have a problem with my audio beats, it had stopped working when I update my drivers software please help as soon as possible.
-
Authorization vs. authentication?
I have a concentrator 3005 and am currently Authenticating users (using the Cisco VPN client software) vs MS Active Directory on Server 2003. However, authentication is not whether the user has obtained the rights to remote access. This means that an