different takes of mousetracks

Similar Questions

• Problem loading Apple Watch sport

  Hello everyone

  Since last week (after update watch OS) do not charge my Apple Watch sport

  more than a minute...

  After a minute, I get an error message saying that 'charge with. "

  This accessory is not supported"even I use the original White

  Magnetic charger and I've never had such an error before.

  I tried to disable the twinning and restart the watch it dosent help

  any suggestions?

  Thank you

  Hello

  Try charging your watch once again. In doing so, check that:

  • All the plastic film was removed from both ends and both sides of the cable support (consult closely on the head of the charger).

  

  • On the back of your watch and the head of the charge cable are clean and dry (clean with an abrasive, lint cloth).
  • The head of the load is properly aligned with the back of the watch, with the concave side / curve touch fully:
    • Some docks of watch, brackets, cases or protectors might hinder it. If you use one of these accessories, try to load the watch by plugging it directly into the charging cable, without using the.
  • If possible, test using a different Apple genuine magnetic Charging Cable (for example, by borrowing one from a friend).
  • If you reload your watch by plugging the cable into the socket:
    • Check that the magnetic charge cable Apple USB connector is fully engaged in the USB power adapter.
    • Check that the USB power adapter is fully committed in the socket.
    • Try to use different maps of the following:
      • Adapter USB Apple that was provided with the watch, or;
      • A 5W Apple (iPhone) or 12W (iPad) USB power adapter, or;
      • A third-party certified 5W (MFi) Apple USB power adapter.
    • Try using a different take (one that is known to work properly).
  • If no other suitable adapters are available, try to load by plugging the cable into a USB port.
    • If loading via a USB port on a computer, make sure that you use a USB 2.0 or 3.0 port, the computer remains turned on and awake, and the cable is plugged directly into the computer (not on, for example, an external keyboard).

  If you identify a problem with a particular component (adapter, cable, or watch) or the question otherwise persists, contact Apple support (mail service may be available) or make a Genius Bar reservation to have your products verified and, if recommended by Apple, served (either under warranty or through a service fee and out-of-warranty):

  • Contact - Support official Apple
  • https://Twitter.com/applesupport
  • http://www.Apple.com/retail/Geniusbar/

  To check your warranty status (the serial number is on the back of your watch):

  • https://checkcoverage.Apple.com/

  More information:

  Check your battery and load your Apple Watch - Apple Support

  If your Apple Watch does not load, or it lights - Apple supports

• "Snake error" - Apple Watch

  Help me! I have the error of snake on my Apple Watch

  Hello

  The symbol of a bolt load cable and lightning appears when your watch battery has a low battery level.

  Try charging your watch for at least 2.5 hours (and maybe longer, for example during the night).  When you reload your watch, check that:

  • All the plastic film was removed from both ends and both sides of the cable support (consult closely on the head of the charger).

  

  • On the back of your watch and the head of the charge cable are clean and dry (clean with an abrasive, lint cloth).
  • The head of the load is properly aligned with the back of the watch, with the concave side / curve touch fully:
    • Some docks of watch, brackets, cases or protectors might hinder it. If you use one of these accessories, try to load the watch by plugging it directly into the charging cable, without using the.
  • If possible, test using a different Apple genuine magnetic Charging Cable (for example, by borrowing one from a friend).
  • If you reload your watch by plugging the cable into the socket:
    • Check that the magnetic charge cable Apple USB connector is fully engaged in the USB power adapter.
    • Check that the USB power adapter is fully committed in the socket.
    • Try to use different maps of the following:
      • Adapter USB Apple that was provided with the watch, or;
      • A 5W Apple (iPhone) or 12W (iPad) USB power adapter, or;
      • A third-party certified 5W (MFi) Apple USB power adapter.
    • Try using a different take (one that is known to work properly).
  • If no other suitable adapters are available, try to load by plugging the cable into a USB port.
    • If loading via a USB port on a computer, make sure that you use a USB 2.0 or 3.0 port, the computer remains turned on and awake, and the cable is plugged directly into the computer (not on, for example, an external keyboard).

  After charging, if your watch has not already restarted automatically, remove the charger and:

  • Try restarting it (by pressing the side button until you see the Apple logo).
  • If necessary, then force try restarting: hold down the side button and the digital Crown for about 10 seconds, until you see the logo.

  If you identify a problem with a particular component (adapter, cable, or watch) or the question otherwise persists, contact Apple support (mail service may be available) or make a Genius Bar reservation to have your products verified and, if recommended by Apple, served (either under warranty or through a service fee and out-of-warranty):

  • Contact - Support official Apple
  • https://Twitter.com/applesupport
  • http://www.Apple.com/retail/Geniusbar/

  To check your warranty status (the serial number is on the back of your watch):

  • https://checkcoverage.Apple.com/

  More information:

  Check your battery and load your Apple Watch - Apple Support

  If your Apple Watch does not load, or it lights - Apple supports

• Tecra R950-104 - can I replace ODD with SSD?

  Hello

  Is it possible to replace my DVD drive with an SSD with a HARD Drive Caddy?

  My laptop is a Toshiba Tecra R950-104.

  Kind regards

  Luis

  Hello

  I found on the internet some UltraSlim SATA HDD/SSD mounting frame that allow the use of 2nd 2.5 HDD/SSD drive instead of ODD in Notepad Tecra R950 but to be honest I m not 100% sure if the BIOS recognize such additional device.

  I know that computers Toshiba laptop (Portege and Tecra) series different takes in charge these updates in the past but this replacement was not supported by each laptop model.

  It depends on the BIOS and in the event that the BIOS recognize the 2nd HDD/SSD drive, the system should be able to recognize 2nd HARD drive

• My helmet speakers are out - prioritize my built in Mic headset

  After finding that the microphone of my helmet (which I thought was broken, since he has never worked on my computer) works very well on my phone, I started to focus on why I can't hear out of it on my computer. Apparently when I set up a microphone on Realtek HD Audio Manager, my helmet speakers are used as the microphone instead as it is built in mic.

  Anyone know if there is a way I can fix this? Thank you

  If you use headphones 'style phone helmet', in other words, only Jack and 3 connectors, his computer map ports usually do not support 3way plugs as you have, only 2 (or in the case of mic).

  You most likely will need a headset with a plug for speakers and a microphone. The microphone can be recognized in the port of real, but pregnant mic (on headpones) will not work.

  It is a hardware limitation, your phone has a different take than your computer does (very probably).

• Satellite Pro L40 - network LAN adapter does not connect

  We had a satellite pro L40 for about a year and have connected to the internet through our wireless home network using the connection Wireless on the laptop.

  My son has now gone to the University and tries to connect to a wired connection via the network adapter, but without success. He tried 3 different cables and different takes the work of others within its rooms, so we know the cables and connections to work.

  Setting up the program guard in him asking to connect the cable, which he did. Adapter network said he works in the control panel and new network connection section, it says to connect the cable.

  Any ideas would be welcome!

  Steve

  What is the "Installer"?

  Try to disable the firewall and update the LAN drivers on the Toshiba site.

• HP Pavilion a6214x desktop - sound no longer works.

  I upgraded Windows 7 SP1 from Windows Vista (that came with the computer). Functioning very well working after the upgrade, but recently stopped. I don't have speakers, so I'm interested to troubleshooting problems of his helmet.

  I tried different helmet and different takes, but no luck. HP website does not sound any BIOS update available for my computer.

  Any help would be appreciated. Thank you!

  Hello

  try to update your readers adio...

  Use this link to download your audio discs

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&product=3633809&

  If you have still no sound, open windows control panel, open administrative tools, and then open Services.  Verify that the following services are all showing that status = started and the Startup Type = Automatic

  Audio service

  Multimedia class Scheduler

  Windows Audio

  Windows Audio endpoint Builder

  If you need to make a change to one of the above, just right-click the service and select Properties, and then in the drop-down list box next to "Startup Type", select automatic and click on apply to save the changes.  Then click on the Start button.

  * By clicking on the laurels! White Star is a great way to say thank you on any post that you helped or solved the problem.* *.
  * By selecting 'Accept as Solution' for an answer that solves your problem helps others who are searching the Web for an answer *.

• U3415W, horizontal line flicker

  Every half hour to two hours, there is a spark of the horizontal line on the screen. It is white or static (can't really say since it is and disappeared in a blink of an eye.) It didn't happen with my old monitor (a Dell 24 "a few years ago.). So far I have tried:

  • Different cables. Used two cables CDM DP, one cable of DP and two HDMI cables. This includes the cables in the box.
  • Plug the monitor into a different take of the surge protector, plug it into my ups and directly into the wall outlet.
  • Reinstalled my video card and ram.
  • Tried the last three versions of the nvidia drivers. The video card is a game of GTX970 of MSI.
  • Checked the integrated diagnosis of the monitor. There's no problem.

  I can't try another video card because I don't have another card with display port or hdmi. I would like to have a video of this. It happens sporadically and not continuous, making it very difficult for me to get a video. Any ideas on what else can you do?

  I'm not convinced that the monitor is at fault. But getting traded.

• 5.1 surround Sound speaker system does not work in Windows 7 Professional 64-bit edition

  My problem is about the same as other users who cannot get their surround sound speaker system to work properly in Windows 7.

  I have a subwoofer and 5 speakers (2 front, 2 rear, 1 for the centre).  Connection to the RealTek HD Audio embedded is simple, orange for the subwoofer, green for the front and black for the rear.

  Test the sound in Control Panel-> windows sound produces a sound on all channels and RealTek HD Audio Manager at the same time, which is the desired configuration.

  However, different applications use different channels.  IE and Firefox use the front channels, VLC/MediaPlayer uses the back.  3D games (that is to say WoW) through all channels.  In each case the subwoofer does not work.

  I tried to download the latest drivers on the motherboard (Gigabyte) manufacturers site.  I even tried the supplied RealTek drivers (even if on the Web from RealTek site which is NOT recommended).  I tried to connect the connectors of the subwoofer to the different takes (reversed black and green).

  I have experimented with the settings in RealTek HD Audio Manager and control panel-> windows Sound.  Nothing works.

  These exact same subwoofer and speakers worked perfectly well on Windows XP.

  I have 2 questions:

  one) has anyone resolved their 5.1 & Windows 7 problem something that I have not yet tried?

  (b) when will Microsoft take this issue seriously?  All Microsoft provided answers just repeat what everyone

  has already tried.

  First disconnect the cable 3 (orange, green and black) then click on Control Panel configuration-hardware and sound - Real tek HD audio manager - central tick, subwoofer and rear pair, front left and right and filling of speaker

  Then click on advance device settings.

  Select "perform front and reading of output devices back two different audio streams simultaneously" and give ok

  Plug all three pins one by one and select the appropriate option in the popup windows.

  That's all.

  You give enough information for me to get this working.   My system runs Win 7 X 64 Home Premium.   When I select 5.1 sound capacity side my 550 x Logitech speakers are not recognized.  If I select 7.1, which is the capacity of my chip Realtek chipset, I can get the two outside are activated as a "rear" speakers and can push the test tones to each of the four surrounding speakers and the combination of Center/bass via the Realtek driver.

  Regarding the "front and reading of output devices back two different audio streams at the same time" worries... I can't find this option.  There are at least two suppliers of 'control of the interfaces' assets on my system.  One is provided by RealTek, the other by Microsoft.  The access roads to these interfaces is roundabout and confusing, to say the least.

  Some compromises are in order in my humble OPINION.  I have my Pandora one stream play in an acceptable way in my small study.  Many of the source of sounds streamed to me are recorded in stereo or mono, I find myself hitting the 'matrix' on my Logitech X 550 button quite frequently.  Sometimes a more recent piece is delivered which actually looks Ok without the decoder "matrix".

  What I would really like to be able to do is to "reconfigure on the fly" between the built in speakers on my Acer Z3731 system USB bar ' All in One ' and my external Logitech X 550 popular with the ability for the presentation of "5.1 surround sound" through three sons.  When I try your procedure, I don't get separate recognition of each thread, as it is trendy and often end up with its 2.1 being eliminated in my 5.1 speakers, because somehow Microsoft has re-recognized the built-in USB port based his bar instead of the three rear wires plugged into the outlets provided by the manufacturer of the system.

  If there was ever separate 'Speakers' and 'Realtek' icons in the UI on my system, speakers are long gone and I can't get back them.  All I see is the Realtek driver.  I would like to see the two icons 'Speakers' different, I could mark "integrated 2.1" and "5.1 external '", in addition to the driver Realtek.»  How can I get these to reappear?

  Can anyone suggest a way to have two different sets of "speakers" recognized and identified in the Microsoft UI in addition to the Realtek driver?  If I could get because of this, I think that the driver would let me 'set as default' one or the other speaker set, and I 'software switching' capable of letting me choose the external speakers or integrated sound bar offers the sound.

• Screen pushing problem in the incoming call disconnected event

  When a phone call disconnects I would push a screen containing some information about the appellant

  In the call disconnected event I'm doing this:

  UiApplication.getUiApplication () .requestForeground ();

  UiApplication.getUiApplication () .pushScreen (new CustomScreen());

  It works most of the time.

  But when I close this screen the phone keypad.

  And sometimes my screen does not get pushed and the keypad appears.

  I could be wrong, but I guess that my screen is pushed in the wrong context?

  Can someone point me in the right direction?

  See you soon

  I have a slightly different take on this problem.

  I think that you run this code:

  UiApplication.getUiApplication () .requestForeground ();

  UiApplication.getUiApplication () .pushScreen (new CustomScreen());

  at your disposal, and if you run in the context of phone, not your application.

  The treatment of changes to it it context moves to your application - the best way to proceed is to use a Global event.  Search for informaiton on world events so this is new to you.

• Smartphones blackBerry PLUG

  I had a phone in the BB world for years and ended prompting for all staff.  I have the charger mini firewire standard type plug with a charger at home, office, kitchen cars, everywhere.  Now, I get a "BOLD" and it has a different take.  What's the point of that?  To make me go out and buy all new Chargers?

  UH... no BlackBerry device has a mini-firewire connector or port.

  It was a Mini USB port. Since on the Storm1 and 8900 devices a year and a half previously, all BlackBerrys have moved to the MICRO USB port and the connection. RIM has done so as part of a standardization of Chargers industry wide. The EU demanded that cell phone manufacturers.

  So, now you know.

  What I have, because I also wanted to continue to use my other chargers, did buy a Mini Micro USB adapter on eBay.

  Like the image below. I bought so cheap as ten of them, and gave a few friends.

  This has been discussed in the Forum here many times, the search would have found it... but not if you're looking for "firewire'.»»

• Audio surveillance?

  What do you use to monitor audio and is there a technique for this? I've heard say that some editors like to listen to their work on a few different devices/systems. Is it true and it follow you?

  The quality of the follow-up that an editor needs depends on if they make the final audio sweetening or audio post-production going. All my final Mix I do myself and I have a configuration high quality 5.1 properly aligned. Most of my Mix find you on Bluray or dvd and I also check the final product on national television, this is a good test for the intelligibility of dialogue. If someone else does post-production audio everything you really need to hear is the dialogue so good semi pro speakers should be ok, I avoid computer speakers would not be expensive. In cases where the editor has to make a judgement of quality, perhaps the choice between two different takes a pair of high-quality headphones work fine.

• How can I disable all auto settings in Camera Raw?

  SUMMARY:

  I am trying to open my images in Camera Raw (version 8.6.0.254) via Bridge CC exactly how they were taken behind closed doors, with no auto setting whatsoever.  I already have boxes that automatically disabled in the Camera Raw preferences under default Image Settings dialog.  I'm shooting raw on a Sony A7r.

  MORE INFORMATION:

  This discussion is not be created without prior research on how to solve it.  If all goes well, there is a simple solution that I have neglected and missed when looking for her.

  I shoot my raw flat images on purpose.  Saturation in camera is rejected, as well as many other parameters of profile picture in the camera.

  I use Bridge CC to sort my pictures well and chooses to make.  In Bridge, I "prefer embedded" selected for my nail of the thumb in order to stop the automatic processing that can happen to the thumbnails here.

  The problem is, as soon as I open my raw images in Camera Raw in bridge, the settings auto kick and saturation and exposure are automatically adjusted.  I can't figure out how to stop Camera Raw adjustments to my raw images.  As noted above, all auto checkboxes are not checked in the Camera Raw preferences.

  When you press the shortcut "Command U" after opening an image, she applies to the auto settings, clearly indicating the Camera Raw thinks that nothing has been yet implemented.  Switch between 'Camera Raw default' and 'Image Settings' in the menu in the menu drop-down does nothing no more.

  Here are two screenshots.  How the thumbnail looks like the bridge, desaturated and flat.  The other is how the image is opened in Camera Raw with no user adjustment what so ever.  You can see how the saturation and exposure have been adjusted:

  Bridge Preview--is how the picture was taken behind closed doors.

  

  Camera Raw - directly after opening the file with no user setting.  You can clearly see the dramatic auto settings, but all cursors are defined by default.

  

  I would like to help with this, so I can see and work on my images as they were shot.  IM really hoping it is an oversight stupid on my part with an easy solution.  Thanks for the help.

  Technically speaking, there are not supposedly automatic adjustments for raw images. Open a raw image in Camera Raw default is applied to this image. Initially, these default settings are defined by Adobe based on their correspondence the parameters against a few test images (I guess). These default settings will be applied automatically because they are the parameters 'default '. If you want your images opened differently, take time to load one of your images and then adjust all the settings the way you want, to be initially. Then save the new default values of the camera to the camera. From this point, all newly opened images will have these settings applied. And you can apply these settings to any image that is already open by clicking on the reset button.  Note that you can have custom default for each camera, and you can even have different settings for different ISO settings. So if Camera Raw is a job you like, just take the time to customize your workflow.

• 2.0.1 is ready for production?

  I followed disappointing discussions of users having problems since switching to the 2.X Server and I was wondering...

  The current version has solved all the questions, and it is worth to start updating my 1.X to the current 2.X servers?

  If not, why?

  Consider that the consensus of the group is this version of VMware server 2.x is * _not_ * ready for production, but some people use.

  Fix?

  I think that there are enough naysayers to give that impression.  However, I have a slightly different take on Server2.  I agree that Server2 is also 'ready for production' as Server1.  As features go, server1 server2 & are the same question when compared to the ESX.  The main reasons that I installed server1 server2 & instead of ESX for a client is because their equipment is not compatible and they needed only to run virtual machines 2 or 3.  Add to that the staff of the customer not being is not familiar with the command line so Server1 or 2 on a host Windows would be more 'comfortable' for the customer.

  That said, why NOT install or upgrade all non - ESX hosts to Server2?  I don't really have that one element that I consider 'not ready for production' L the Console.  I still have problems to get the plugin sometimes works.  Enough times that I use especially the ESX3.5 VIClient to manage the Server2 hosts.  Continues like that would be fine with me, but customer vSphere4 does nor support the Server2.  For this, I may abandon Server2 down to "not ready for production."  But other console, have not really a problem with Server2 in production.

• Replacement card mother XPS 730

  I've had problems with my 730 for a few years now. Initially, research told me that the power supply or capacitors were the cause. I bought a handful of replacement capacitors and took part, the system to replace the suggested guilty. The system has become very stable from there, but recently, the symptoms returned. The system crashes suddenly, keyboard and mouse are unresponsive, screen is frozen and sometimes a unique tone from the speakers. The only option is hard stop the start up. Sometimes, this can happen every few minutes last time once a week.

  I replaced the sticks 4x1Go with sticks of 2 x 4 GB Patriot memory and the video card abandoned some time back then I have an ATI Radeon HD5770.

  Recently, I replaced the original RAM but the gel has continued. When I replaced with the Patriot is frozen usually until I moved the second stick of the 2nd to the 3rd and then finally to the 4th slot. Now, it has been relatively stable.

  Could there be something wrong with the memory slots?

  I would do well to replace the motherboard with a new one? I found 4 on eBay for all about AUD100.

  If your system is a 730, you need a 730 motberboard. If it is a 730 x, you will need a motherboard 730 x. They are not interchangeable between the two systems because the x 730 uses RAM DDR3 vs DDR2 on the 730 and a core i series processor vs Core 2 series and has a different take. ThomasLG

  UU795, F642F, 0F642F, CN-0F642F

  These numbers above are motherboards OEM Dell XPS 730 and work with your desktop computer.