display the values of the sample on a graph
Hallo!
I have a problem with a graph, the thing is that I really showed values of Y of the samples on a chart. There is a possibility to make a comment (as in attached photo) but I need the waltz instead. Any ideas? Thanks for the trouble,
Greetings!
Dear Aleph.ka,
Here is an example of what you might need. For more documentation, please refer to the description of the node property applied (Annotation list):
http://zone.NI.com/reference/en-XX/help/371361H-01/lvprop/waveformgraph_annot_list/
I hope this helps.
Kind regards
Tags: NI Hardware
Similar Questions
-
Hello
I have a scanner with the following configuration:
-Sampling rate = 20000000
-Lrecl = 12000000It works very well so far and gives me a sampling time of ~ 600ms. Where the problem occurs is when I want to display the signal in a graph. Here, I get the error message 'insufficient memory '. That's why I used the express vi "compression of sample to reduce the data by a factor of 10'000 for example but this still does not work when I put the entrance of the"Fetch WDT.vi niScope"value"-1 "."
It works when I set this value to 1'000 ' 000 for example but is not a solution because I do not have the full signal until ~ 600ms! I also can't reduce the sampling rate of the digitizer because I will lose the precision of measurement.
How can I solve this problem?
Thanks in advance
Examples of NO-SCOPE contain examples of code explaining how to extract data from map of range into pieces (for example niScope EX Fetch in Chunks.vi). As mentioned above, there are tuturials on how to manage large sets of data to LabVIEW, one using LabVIEW and one here. Between these three sources, you have sample code to pick up your card brought into pieces, decimate for display and display without running out of memory. It's the algorithm and the method used by the NO-SCOPE Soft Front Panel.
-
How can I change this request, so I can display the name and partitions in a r
How can I change this request, so I can add the ID of the table SPRIDEN
from now on gives me what I want:
in a single line, but I would like to add the id and the name that is stored in the SPRIDEN table1,543 A05 24 A01 24 BAC 24 BAE 24 A02 20 BAM 20
SELECT sortest_pidm, max(decode(rn,1,sortest_tesc_code)) tesc_code1, max(decode(rn,1,score)) score1, max(decode(rn,2,sortest_tesc_code)) tesc_code2, max(decode(rn,2,score)) score2, max(decode(rn,3,sortest_tesc_code)) tesc_code3, max(decode(rn,3,score)) score3, max(decode(rn,4,sortest_tesc_code)) tesc_code4, max(decode(rn,4,score)) score4, max(decode(rn,5,sortest_tesc_code)) tesc_code5, max(decode(rn,5,score)) score5, max(decode(rn,6,sortest_tesc_code)) tesc_code6, max(decode(rn,6,score)) score6 FROM (select sortest_pidm, sortest_tesc_code, score, row_number() over (partition by sortest_pidm order by score desc) rn FROM (select sortest_pidm, sortest_tesc_code, max(sortest_test_score) score from sortest,SPRIDEN where SPRIDEN_pidm =SORTEST_PIDM AND sortest_tesc_code in ('A01','BAE','A02','BAM','A05','BAC') and sortest_pidm is not null GROUP BY sortest_pidm, sortest_tesc_code)) GROUP BY sortest_pidm;Hello
That depends on whether spriden_pidm is unique, and you want to get the results.
Whenever you have a problem, post a small example of data (CREATE TABLE and INSERT, relevamnt columns only instructions) for all the tables and the results desired from these data.
If you can illustrate your problem using tables commonly available (such as in the diagrams of scott or HR) so you need not display the sample data; right after the results you want.
Whatever it is, explain how you get these results from these data.
Always tell what version of Oracle you are using.Looks like you are doing something similar to the following.
Using the tables emp and dept of the scott schema, producing a line of production by Department showing the highest salary for each job, for a set given jobs:DEPTNO DNAME LOC JOB_1 SAL_1 JOB_2 SAL_2 JOB_3 SAL_3 ------ -------------- ------------- ------- ----- ------- ----- ------- ----- 20 RESEARCH DALLAS ANALYST 3000 MANAGER 2975 CLERK 1100 10 ACCOUNTING NEW YORK MANAGER 2450 CLERK 1300 30 SALES CHICAGO MANAGER 2850 CLERK 950On each line, jobs are listed in order by the highest salary.
This seems to be similar to what you are doing. The roles played by the sortest_pidm, sortest_tesc_code and sortest_test_score in your table sortest are played by deptno, job and sal in the emp table. The roles played by the spriden_pidm, id and the name of your table spriden are played by deptno, dname and loc in the dept table.Looks like you already have something like the query below, which produces a correct output, except that it does not include the dname and loc of the dept table columns.
SELECT deptno , MAX (DECODE (rn, 1, job)) AS job_1 , MAX (DECODE (rn, 1, max_sal)) AS sal_1 , MAX (DECODE (rn, 2, job)) AS job_2 , MAX (DECODE (rn, 2, max_sal)) AS sal_2 , MAX (DECODE (rn, 3, job)) AS job_3 , MAX (DECODE (rn, 3, max_sal)) AS sal_3 FROM ( SELECT deptno , job , max_sal , ROW_NUMBER () OVER ( PARTITION BY deptno ORDER BY max_sal DESC ) AS rn FROM ( SELECT e.deptno , e.job , MAX (e.sal) AS max_sal FROM scott.emp e , scott.dept d WHERE e.deptno = d.deptno AND e.job IN ('ANALYST', 'CLERK', 'MANAGER') GROUP BY e.deptno , e.job ) ) GROUP BY deptno ;Dept.DeptNo is unique, it won't be a dname and a loc for each deptno, so we can modify the query by replacing "deptno" with "deptno, dname, loc" throughout the query (except in the join condition, of course):
SELECT deptno, dname, loc -- Changed , MAX (DECODE (rn, 1, job)) AS job_1 , MAX (DECODE (rn, 1, max_sal)) AS sal_1 , MAX (DECODE (rn, 2, job)) AS job_2 , MAX (DECODE (rn, 2, max_sal)) AS sal_2 , MAX (DECODE (rn, 3, job)) AS job_3 , MAX (DECODE (rn, 3, max_sal)) AS sal_3 FROM ( SELECT deptno, dname, loc -- Changed , job , max_sal , ROW_NUMBER () OVER ( PARTITION BY deptno -- , dname, loc -- Changed ORDER BY max_sal DESC ) AS rn FROM ( SELECT e.deptno, d.dname, d.loc -- Changed , e.job , MAX (e.sal) AS max_sal FROM scott.emp e , scott.dept d WHERE e.deptno = d.deptno AND e.job IN ('ANALYST', 'CLERK', 'MANAGER') GROUP BY e.deptno, d.dname, d.loc -- Changed , e.job ) ) GROUP BY deptno, dname, loc -- Changed ;In fact, you can continue to use just deptno in the analytical PARTITION BY clause. It may be slightly more efficient to just use deptno, as I did above, but it won't change the results if you use all 3, if there is only 1 danme and 1 loc by deptno.
Moreover, you don't need so many subqueries. You use the internal subquery to calculate the MAX and the outer subquery to calculate rn. Analytical functions are calculated after global fucntions so you can do both in the same auxiliary request like this:
SELECT deptno, dname, loc , MAX (DECODE (rn, 1, job)) AS job_1 , MAX (DECODE (rn, 1, max_sal)) AS sal_1 , MAX (DECODE (rn, 2, job)) AS job_2 , MAX (DECODE (rn, 2, max_sal)) AS sal_2 , MAX (DECODE (rn, 3, job)) AS job_3 , MAX (DECODE (rn, 3, max_sal)) AS sal_3 FROM ( SELECT e.deptno, d.dname, d.loc , e.job , MAX (e.sal) AS max_sal , ROW_NUMBER () OVER ( PARTITION BY e.deptno ORDER BY MAX (sal) DESC ) AS rn FROM scott.emp e , scott.dept d WHERE e.deptno = d.deptno AND e.job IN ('ANALYST', 'CLERK', 'MANAGER') GROUP BY e.deptno, d.dname, d.loc , e.job ) GROUP BY deptno, dname, loc ;It will work in Oracle 8.1 or more. In Oracle 11, however, it is better to use the SELECT... Function PIVOT.
-
using a Case statement to display the values of column even as table headers
I have a database that has been set up kind of tricky, in that some tables are made up of columns that are field names and one link to another table that contain the data for these field... also names there ID displays as many lines instead of as a row of data. I would like to write a query to extract that information and display it as one line for each ID.
example: table 1
ID, name, itemresponse and itemcode, Description
Dee Jones Childrens Hospital 123 SITE location
123 dee Jones, Date of appointment next NEXTAPPT 22/04/2014
123 dee Jones was on bedrest NOSHOW reason do not show
I would like to have the display of data as a record on this same patient, instead of as 3 separate registers (with the Description column in table 1
Table 2
ID, name, place, Date of the next meeting, show no reason
123 dee Jones Childrens Hospital 22/04/2014 was the bed rest
I have included the code I worked on below my question, for me to get the desired results should I use the Case statement and it's the right way to do it below?
(SELECT
PAT.ID "PATIENT ID."
PAT. FIRST | » '|| PAT. "PATIENT FIRST NAME."
PAT. "PATIENT DOB," DATE_OF_BIRTH
DS. Date 'Date of inpatients ',.
Dai. ITEM_CODE "Item Code",
Dai. DESCRIPTION "Description."
Siad. ITEM_RESPONSE,Max (CASE WHEN dai. ITEM_CODE IS "SITE" THEN DAI. Decription
ANOTHER NULL
END) AS "name of the hospital."
Max (CASE WHEN DAI.) ITEM_CODE IS 'NEXTAPPT' THEN DAI. ITEM_Description
ANOTHER NULL
END) AS 'next Appt Date. "
Max (CASE WHEN DAI.) ITEM_CODE IS "LASTDATE" THEN DAI. Description
ANOTHER NULL
END) AS 'last visit Date.
Max (CASE WHEN DAI.) ITEM_CODE IS 'NOSHOW' THEN DAI. Description
ANOTHER NULL
END) THAT "the reason has not shown".
Of
(PAT.ID "IDENTIFYING PATIENT",
PAT. FIRST | » '|| PAT. "PATIENT FIRST NAME."
PAT. "PATIENT DOB," DATE_OF_BIRTH
DS. Date 'Date of inpatients ',.
Dai. ITEM_CODE "Item Code",
Dai. DESCRIPTION "Description."
Siad. ITEM_RESPONSEOf
dm_sessions Ds,
dm_session_assessments dsa,
DAS dm_admin_sections,
dm_session_assessment_items Siad,
Dai dm_admin_items,
Po Patient_Orders,
Inventory inv,
Patients_Table PAT
dm_admin_categories CAD
where dsa.session_Id = ds.session_Id
and PAT.ID = ds. Patient_ID
and dsa.excluded_assessment =' no
and dac.category_code = 'OPEN'and dsa.section_id = das.section_id
and das.category_id = dac.category_id
and das.section_code = 'northwest'
and dai.section_id = das.section_id
and dsai.item_id = dai.item_id
and dsai.session_assessment_Id = dsa.session_assessment_Id
and dsai.excluded =' no
- and Dai.ITEM_ID = Dsai.ITEM_ID
and Dai.ITEM_CODE IN ('SITE', 'NEXTAPPT', 'LASTDATE', 'NOSHOW')
and po.patient_ID = ds.patient_ID
and in. NDC_NO = inv. NDC_NO
and inv. TDRUG_ABBREV = in. DRUG_ABBREV
PAT.ID GROUP, PAT. FIRST | » '|| PAT. LAST, PAT. DATE_OF_BIRTH, ds. Date, dai. ITEM_CODE, dai. DESCRIPTION, Siad. ITEM_RESPONSE))Hello
DATE is not a very good name for a column. Use something like EVENT_DATE, that will not be confused with a keyword from Oracle, instead.
I don't see something like this column in the CREATE TABLE statement. He will always be the same value on all lines?
Here's a way to get the results you requested:
SELECT id
first name | ' ' || LastName AS name
Date of birth
MAX (CASE WHEN item_code = "NEXTAPPT", THEN item_response END) AS next_appointment,
MAX (CASE WHEN item_code = "LASTDATE" THEN item_response END) AS last_visit_date,
MAX (CASE WHEN item_code = "SITE" THEN item_response END) AS location
FROM mytable1
GROUP BY id, firstname, lastname, dob
;
Of course, I can't test it very well until you post INSERT statements for the sample data.
I guess that 2 or more lines of the entry have the same id, then they will necessarily be first name last name, the name and date of birth, too. No doubt they are standardized in your actual tables.
-
Display the values of the 2D stacked column chart
Hello
I use the following sql which shows the percententage of errors in a month
Now the values are displayed correctly, however, the stacked bar displays the real percentage value, for example 60% on stacked bar. When we mouse over the bar it shows "No D", Sys, Oth. Is there a way to display permanently type Decode and percentages?SELECT NULL , TO_CHAR(MA.DATE_LOGG,'Mon'), sum(decode(el.error_type,'On',1,0)) "Ons", sum(decode(el.error_type,'Pa',1,0)) "Prt", sum(decode(el.error_type,'No D',1,0)) "No D", sum(decode(el.error_type,'Sys',1,0)) "Sys", sum(decode(el.error_type,'Oth',1,0)) "Oth" FROM table1 MA, table2 EL, table3 CR WHERE MA.ERROR = EL.ERROR AND MA.ERROR IS NOT NULL AND MA.COUNTRY = CR.COUNTRY_CODE AND TO_CHAR(DATE_LOGG,'YYYY') = nvl(:P5_FILTER,to_char(sysdate,'YYYY')) AND CR.REGION_CODE = NVL(:P5_REGION,CR.REGION_CODE) GROUP BY TO_CHAR(MA.DATE_LOGG,'Mon'), trunc(ma.date_logg, 'Month') ORDER BY trunc(ma.date_logg, 'Month')
Apex 4.1 / 11g
Thank you
SunHi Sun,.
If you would like to add the series name in the values displayed in the bar of the items themselves, then you will need to customize the XML graph and update the
tag to embed {% SeriesName}. I've added an example for my sample application, indicating where the XML code must be changed: http://apex.oracle.com/pls/apex/f?p=36648:90. For a complete list of available AnyChart keywords, such as % SeriesName, please see the AnyChart online documentation: http://anychart.com/products/anychart/docs/users-guide/label-text-formatting.html?fromtree. I hope this helps.
Kind regards
Hilary -
How can I change the value of the sample during my simulation period?
I'm about to set discrete PID profile vi to specify the values of the period of sampling of the order hold block. At t = 0, I wish that the value of 0.5 and then change to 1.0 when t = 5. Currently, only 0.5 goes to the waiting order discreet block. I think it's because the block takes this value and then use it for the entire simulation, do not check to see if the value has changed. Is there a way to tell the block to check this value at each time step and then adjust if necessary sampling its period?
See code attached for reference.
What is your overall goal for the sampling period? You will change the value more than once? Or only from 0.5 to 1?
The PID setpoint profile should allow you to specify a profile for the values to send to the hold. He will see property values. For example if you specify only t = 0 setpoint = 0.5 and t = 5 setpoint = 1, you'll find it ramp the setpoint in 0.5 to 1.0 for the first 5 steps of time. If you want the sampling period of stay up to t = 5 0.5 is reached you will probably want to three elements in the array. set = 0.5 point t = 0, t = 4.99 set = 0.5, 1.0 = set point t = 5.
If you're just fill one step, (from 0.5 to 1.0) you can use the Index Timestep in the Simulation parameters to determine the sampling period. Is attached a screenshot of what I mean.
-
Read integer values to worksheet and display the values in a table
Hi all
I have integer values to read from a worksheet and display them in a table. I uses 'Reading of the spreadsheet file' mode 'integer '. I want to display these values in a table. The problem is the table takes only 2d-array of string as input but not an integer.
It works fine if I change 'Worksheet file playback' mode to 'integer' to 'chain', but I want to read integers and must use integer values for calculations more. Please give suggestions on the display of integers to a table.
Thank you.
Do not take not piece-by-piece just convert as a whole. See the attached example
Good luck
-
Hi all
I have a questions. It is that I create a Subvi to my table and it can display the last value in the upper part. Below attached snapshots of my programming. I use a number random and STOP for control of you guys let see the whole process of what I want.
but when I change "constant true/false" and using a digital command. and I put it in my program. It won't list down the values and it will not display the most recent value at the top. What is the problem? I was stuck on this problem for a while.
and another question was how to keep the size of the list is constant? for example, I onli wants to view 30readings on my table. as the program continued to run, the oldest value will be overwritten. because if kept under my table more, means memory increase my programming and registration of cause late development. I do not want to happen. So is it possible to maintain the display of fixed table values?
Hi Isabelle,.
I think that the problem causes initialization of a register shift to void / vi. If you initialize a shift register, each time sub vi is called, he will replace value in the registry to offset with initialized value. Uninitialize a registry change to resolve a problem. I've attached a screenshot of my sub vi for your reference.
Sincerely, Kate
-
Is it possible to connect a simple 1 d array to a digital indicator or what would be the best way to display the numeric values of the array on the front panel? Examples or suggestions would be greatly appreciated.
Thank you
Tunis
Thank you Adam, it's originally in a while loop, I placed it in a loop for example, wired County in the for loop and presto, this son of a digital indicator. It works very well. Thanks for the help folks.
-
Display the values in a list in a certain way
Hello
I'm looking for a way to display the values in a list by the first value by a slash and the rest with an indentation.
In other words in this way:
/value
Value1
value2
value3
etc...
Please see the attachment for a better reference where data are received and then filled to the window list.
Thanks for your comments
Thanks guys,.
I endend up doing this:
If (i == 0)
{
sprintf (current_log_view, "/ %s", cnfg_display_db [i] "");
}
on the other
{
sprintf (current_log_view, "%s", cnfg_display_db [i]);
}
SetCtrlVal (log_panel, LOG_LOG_TB, cnfg_display_db [i]);
InsertListItem (dir_list_panel, DIR_LIST_RETR_LIST, current_log_view, i, 0);and it works very well!
Thanks again
-
Selector - return and displaying the selected value
Hello all, I have problem with selector which is connected to the simple XML through XMLDataModule.
Definition:
{} Selector
ID: piCountry
Title: qsTr("Country:") + Retranslate.onLanguageChanged
dataModel: {XmlDataModel}
Source: "states.xml".
}
pickerItemComponents:]
{PickerItemComponent}
type: "ListItem".
content: {container
{Label
text: pickerItemData.title
}
}
}
]
onSelectedValueChanged: {}
var piCountry.dataModel.data = selectedItem ([0, selectedIndex (0)]);
Console.log("Selected>"+SelectedItem.Text)
}
}STATES. Model XML:
...
1. I can't achieve good get selected value based on the index selected. After Exchange of selected value, the error message appears:
ERROR: UIObjectPrivate::notifyMessage: unable to set the focusIsDelegatedToColumn property
ERROR: UIObjectPrivate::notifyMessage: unable to set the focusedColumn property
some > undefined2. is it possible to display the value selected in the selector bar (after choosing and collapsing)?
Thanks for any idea, I have been addressed in the morning but no reasonable results so far.
Thank you.
Karel
Looks like you're missing the good at the end, add a ".title' in there like this:
var selectedItem = piCountry.dataModel.data([ 0, selectedIndex(0) ]).title;
Here is an example of a complete code of a similar selector to select a State, and also has a method to set the value of an external call and a method to change the title, once the switch has been reduced (must cover your 2nd question).
/* Copyright (c) 2014 BlackBerry Ltd. * * Licensed under the Apache License, Version 2.0 (the "License"); * you may not use this file except in compliance with the License. * You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. * * Created on: May 5, 2014 * Author: Mark Sohm */ import bb.cascades 1.2 Picker { property string stateValue: "" id: siteStatePicker title: "State" kind: PickerKind.Expandable dataModel: XmlDataModel { id: stateModel source: "../xml/US_States.xml" } pickerItemComponents: [ PickerItemComponent { type: "state" content: Label { id: stateLabel text: pickerItemData.name } } ] onSelectedValueChanged: { siteStatePicker.stateValue = dataModel.data([0, selectedIndex(0)]).name; } onExpandedChanged: { if (!expanded) { siteStatePicker.title = siteStatePicker.stateValue; } } //Used to set the selected state. function setState(state) { for (var count = 0; count <= 49; count++) { if (state === stateModel.data([0, count]).name) { siteStatePicker.select(0, count, ScrollAnimation.None); siteStatePicker.stateValue = stateModel.data([0, count]).name; siteStatePicker.title = siteStatePicker.stateValue; } } } }It's xml data.
-
Displays the value of double type
Hi - another crazy me today. With the help of v % of the SDK. Memorization of the GPS coordinates in a persistent storage which is fine. So want to show these results on a screen by updating a labelField with the value.
the code below, printLn myTest displays a value of something as 42.1234 gets so thin value. However, with the code so I get Double.toString (myTest) cann't find symbol even though I java.lang. *; imported. If I remove this line of double.toString then it will compile, but throws an exception error when I try to display on the screen. Can someone help a newbie pls...
If (persistentHashtable.containsKey ("LVFLat")) {}
Double myTest is (Double) persistentHashtable.get ("LVFLat");.
System.out.println ("# latitude =" + myTest);
String finalLat = Double.toString (myTest);
displayLVFLat.setText (myTest);
}You must read the documentation of the API and note the use of capital letters and tiny. Capitals: the object, tiny, primitive. Read the API done again and see what I mean.
You want to replace this:
String finalLat = Double.toString (myTest);
with
String finalLat = myTest.toString ();
-
Possibility to get a popup to display the display value "" and not the "return value".
Version - Application Express 3.2.1.00.11
I have a list of values that exceed 1500 files and am so impossible to use a Select list.
When you use a popup lov after choosing the recording, apex displays the return value (in my case a number). Is it possible to let him use the display value (in my case, a text string).
Concerning
Ben
Benton says:
Version - Application Express 3.2.1.00.11
I have a list of values that exceed 1500 files and am so impossible to use a Select list.
When you use a popup lov after choosing the recording, apex displays the return value (in my case a number). Is it possible to let him use the display value (in my case, a text string).
See limiting the number of values in a LOV
If it comes to a page element, and then change the type of Popup LOV key.
If there is a control in a table, it's another reason to upgrade to a supported version, or the tabular form will need to be converted to be manually generated and processed in order to allow the appropriate control be returned using the
apex_item.popupkey_from_lovmethod -
Hi Forum members,
I am looking for a query display the name of the tag as the column name and the value in the tag as a row of data.
I have to print the values within the tag to a file by choosing the value of the flags. the sequence of the tags will vary each time, as the tag name will change dynamically.
So here is the example of input data and the expected output. The string in the text column must be separated as the column names and values.
Input data
Select 1 as seqno,' < > 0210A 50 4f < / 4f > < 5f20 > TEST CARD 16 < / 5f20 > < 5f2a > < / 5f2a > < 82 > 1 c 00 < / 82 > ' double text
Output:Seqno 4f 5f20 5f2a 82
0210A 50 16 1 00 TEST CARD 1Please help me by providing your entries on this.
We use the version of Oracle 11.2.
Note: This is not the XML string
Thank you
Shree
with
data in the form of
(select 1 as seqno,'<4f>0210 A 50<5f20>TEST CARD 16<5F2a><82>00 1' text of all the double union)
Select 2 as seqno,'XYZ<4F>0210 A 50<5f20>TEST CARD 16<5f2a><82>00 1' text of all the double union
Select 3 as seqno,'<4f>0210 A 50<5f20>TEST CARD 16<5F2A><82>1 00XYZ ' text of all the double union
Select option 4 as seqno,'<4F>0210 A 50<5F20>TEST CARD 16<5f2A><82>1 00XYZ' double text
)
Select d.seqno, x.*
d the data,
XMLTable ('/ root')
by the way xmltransform (xmltype ('
': replace (replace (text,'<><> '),)))XmlType (q'~
~'
)
)
path of columns '4f' varchar2 (10) "tag4f."
path of "5f20' varchar2 (30)"tag5f20. "
path of '5f2a' varchar2 (10) "tag5f2a."
path of varchar2 (10) "82" "tag82.
) x
SEQNO 4f 5f20 5f2a 82 1 0210A 50 16 TEST CARD - 1 00 2 0210A 50 16 TEST CARD - 1 00 3 0210A 50 16 TEST CARD - 1 00 4 0210A 50 16 TEST CARD - 1 00 with
data in the form of
(select 1 as seqno,'<4f>0210 A 50<5f20>TEST CARD 16<5F2a><82>00 1' text of all the double union)
Select 2 as seqno,'XYZ<4F>0210 A 50<5f20>TEST CARD 16<5f2a><82>00 1' text of all the double union
Select 3 as seqno,'<4f>0210 A 50<5f20>TEST CARD 16<5F2A><82>1 00XYZ ' text of all the double union
Select option 4 as seqno,'<4F>0210 A 50<5F20>TEST CARD 16<5f2A><82>1 00XYZ' double text
),
Chopper (seqno, Key, value, String) as
(select seqno,
regexp_substr (text,'<(.+?)>', 1, 1, null, 1),
regexp_substr (Text,'>(.*?))
regexp_substr (text,'<.+?>. *? ) (.*) $', 1, 1, null, 1). » <>'
from the data
Union of all the
Select seqno,
regexp_substr (String,'<(.+?)>', 1, 1, null, 1),
regexp_substr (String,'>(.*?))
regexp_substr (String,'<.+?>. *? ) (.*) $', 1, 1, null, 1)
Chopper
where regexp_substr (string,'<(.*?)>', 1, 1, null, 1) is not null
)
Select '4f', seqno, '5f2a', '82', '5f20.
of (seqno, lower (key) select key, value)
Chopper
)
Pivot (max (value) for key in ('4f' as '4f', '5f20' as '5f20', '5f2a' as '5f2a', "82" as "82"))
Concerning
Etbin
-
Display the value of the column automatically based on another column in a table
Hello
I use APEX 5.0, I have a requirement to display the field automatically based on the tabular presentation of other numbers.
in the screen shot attached above when I press Add button line a new line is created and enter the value in 'place no.', 'dept and identification of height place' when I press tab or get out of the column "height", "GID" should appear automatically.
To display the GID my query will be like that. "Select GID from x where no = '1011' place and dept = 88 and height = 88'.
How to get the value of from GID of the another value entered in Place no, dept and height in tabular form.
Thanks in advance
Ravi.
Hi Ravi
No need to point of Application or process. I just completed the task with the following steps
(1) create 4 hidden items
P2_SELWID
P2_SELDEPTH
P2_SELHEIGHT
P2_CALCWNAME
(2) gives 3 CSS classes in three columns of tables.
. WID
. DEPTH
. HEIGHT
(3) create the function jQuery for re - get three items from the page on a line if one of them has been changed.
Add the following code to the function and the declaration of global variables
function setRowItemValues(p_rownum){ wid_col_id = 'f02_' + rownum ; wid_col_val = $('#'+wid_col_id).val(); depth_col_id = 'f03_' + rownum ; depth_col_val = $('#'+depth_col_id).val(); height_col_id = 'f04_' + rownum; height_col_val = $('#'+height_col_id).val(); wname_col_id = 'f05_' + rownum; // set P2_SELWID,P2_SELDEPTH,P2_SELHEIGHT $s("P2_SELWID", wid_col_val ); $s("P2_SELDEPTH", depth_col_val ); $s("P2_SELHEIGHT", height_col_val ); $s("P2_SELWNAMEID", wname_col_id ); // Call the Dynamic Action to get WNAME if all values are not null if( wid_col_val != '' && depth_col_val != '' && height_col_val != '' ){ //Call DA to Get WNAME from WINT $.event.trigger("CalcWNAME"); // set the Tabular form $('#'+wname_col_id).val($x("P2_CALCWNAME").value); } }and run when the Page loads
$(document).on("change", ".WID,.DEPTH,.HEIGHT", function(){ rownum = $(this).attr('id').substr(4); setRowItemValues(rownum); });(4) create a dynamic Action to get WNAME based on a PL/SQL function. Note the submitted page elements.
CalcWNAME
(5) set of the corresponding element in the line of the function jQuery, after completing the DA.
Please check and I hope your problem is now solved.
Concerning
Mahmoud
Maybe you are looking for
-
Hello I have a weird problem, & I don't know how to explain it well. So, I say from the outset. I copy some files from my laptop to a 4.7 GB DVD. While it has been copied, I was you rename a file in my notebook when suddenly the blue screen of color
-
HP Pavilion dv6-6177la - Drivers Wifi problem
Forum on HP good night: With cordial greetings, I would like to post my situation: I recently bought a HP laptop? HP Pavilion dv6-6177la? and after you create the recovery image, I formatted and installed Windows 7 Ultimate English. I have been succe
-
How can I restore Disk Cleanup tools system folder?
Well, my disk cleanup and Disk Defragmenter are in all programs > Accessories > system as usual tools. I don't know how to run the programs, although by going into properties system, etc, but I would like to know how to get back them in this folder t
-
Generate a web page to display the subset of the image
Is it possible that one can spawn a web page with the news of subset of a couple of layers? Let's say I calculate some RGB layers information and I would like to see the information on a web page in near real-time. Info would probably be in another
-
The image in the MovieClip from the cake overlaps the other two clips. Therefore part of the click of each part of the cake box is in conflict with a part of the click of another part of the cake box. How can I solve this problem in Adobe animate?