DNS probe finished no internet

Similar Questions

• ' DNS probe Finsished no Internet ' on the data after 5.1.1 update

  I liked having my Sony Xperia Z3 Compact until recently after the 5.1.1 update... Since I've updated my phone, he had problems connecting to the internet using data.  Wifi works fine, but when executing the data after a few minutes I get the error 'DNS probe finished no Internet.

  I contacted Sony and I tried all the suggestions of the Sony Agent (reset the phone, button next to the sim card and restart full and updated through the computer using PC Companion).

  I've seen people with this problem on any other Forums Android, but I thought I'd try here... Everyone knows about this problem?  And even better a solution? (without sending to my phone to Sony, because it takes weeks... and I want to not "find something wrong")

  Just found this on another post on the forum and I think it relates to my problem so I try it:

  Reddit FishStik5 user: go to the APN settings and replace the AFN iPv4 Protocol only (it was before iPv6) seems to fix the problem.

  How do I find the setting: parameters-> wireless and network / more->-> T-mobile data, mobile networks-> APN-> APN Protocol-> set for IPv4.

  This seems to solve the problem for me.

• "No DNS server," "PPPOE server," "Internet connection" - WARNING amber

  I'm troubleshooting on iMac my parents - there is a problem with the configuration of the Airport Extreme. The iMac is fully updated.

  During the configuration of the airport, I get this chart:

  

  Under 'Of Carol Airport,' I can't seen to change the State of the servers DNS, server PPOE and Internet connection. The iMac works fine without the airport connected... but when you're connected, I get these errors.

  How solve the three errors and get the router working again? Please provide very detailed responses, if possible. Thank you!!

  The problem lies in the device upstream 'Carol airport'.

  Reset by it turn it off and leave it like that for a few moments. Internet service providers often suggest disconnect their cable from their device as well (not the Ethernet cable between it and the AirPort Base Station - please leave one connected). There should be no need of power towards the low 'of Carol Airport', but there is no harm in doing so, either.

  Then, connect it to power again, and reconnect the cable if you disconnected it. Give it a moment to start to finish. Connect the "Carol airport', if you we turned off.

  Please proceed to configure the AirPort base station by following the instructions.

• Win7 x 64 no connection with possible XPs, group WORK, NetgearSwitch108, IP and DNS automatic, very good Internet

  some free files, LAN: ok Internet TPCP/IPv4, when I use the HELP for NetProblems my Win7 x 64 crashes down. no solution in Windows Help Center.

  The LAN router connection: each PC has its IP address individual, why does'nt it works?

  See a procedure step by step for the creation of a network of Ethernet cable of two computers between Windows 7 and Windows XP with ICS

  but ignore all references to the configuration of the IP addresses as your router / switch controls those.

• My Firefox browser cannot access the Internet, so I use my iPad.

  I forgot that I have to use my iPad email. My office is not talking about the Internet this week. Troubled shooters are no solution. The closest I can come the problem is a message from the homepage on chrome. It says 'DNS probe finished. "
  no internet"not much to go for me in any case. Appreciate any help that anyone can provide. I suspect a proxy problem, but it's way above my head. I am former over the years and the new in computer talk, so be simple in steps to resolve. Thank you. George sends.

  _{Edit: removed personal information for your protection. (philipp)}

  Type of topic: preferences #advanced< enter > in the address bar.

  Under Advanced, select network.
  Search for configure how Firefox connects and then press the settings button.
  If you use a proxy server, make sure that these settings are correct. If there is no
  proxy, first use No. Proxy. If there is a problem, then try Proxy system.

  Some problems occurs when your Internet security program has been implemented.
  trust the previous version of Firefox, but not more acknowledges your
  update as being approved. Now how do I solve the problem: to allow
  Firefox to connect to the Internet

  • Make sure your Internet security software is up-to-date (for example, you are using the latest version).
  • Delete Firefox to list your program of programs approved or recognized. For detailed instructions, see

  Configure the firewall so that Firefox can access the Internet. {web link}

• Why our local DNS server, discount Internet user if the user insert new internet address?

  We have a local DNS server that has a strange problem. If a user insert new internet address DNS will cut this internet user. So every time that the user want to insert the new internet address that he must fix his connection and then refresh the browser to display the page.

  How can I fix this error?

  Hi Saman,
  first things first... more information is needed to correctly diagnose your problem.
  When you post a question please include at least the system operation, error message, and what happens when the issue appears.
  Second, server or business systems problems most will be better suited to Microsoft's Technet forum.
  Try this link below for search/post:
  http://social.technet.Microsoft.com/search/en-us/?query=DNS%20Server&refinement=112&AC=3
  B Eddie

• No Internet access with EA2700

  I recently bought an EA2700 to replace an old Belkin. I ran the set up CD and I'm unable to establish an internet connection. I am able to connect to the router (wired and wireless), access the settings, etc. but can not reach the net. I tried to disable the firewall, DNS of hot flashes, disabled IPv6. Did all the basic steps, resett the router/modem, etc... nothing. I plug in the Belkin and it connects fine. Any help would be great.

  Oh, Ive tried my laptop (win7) and desktop (Windows XP) and both have the same problem.

  I hate it when the solution is simple.

  Thank you very nice folks at Cisco, we were able to get the connection.

  We have:

  -by default of the router (reset button)

  -power to bike all devices

  -uninstalled and reinstalled Cisco Connect (did not try the first time around)

  -After the configuration, an update was necessary.

  -After the update is finished, the internet connection was created.

  Hope this helps

• DNS error on wifi. No problem on ethernet

  Hello everyone

  I have a weird problem with my internet. WiFi works fine on my tablet, phone etc. But not with my pc. I get the dns probe error when I try to connect to my pc via wifi.however when I use the ethernet cable it works very well. I tried RAS dns as well as the evolution of my dns address for open dns. I am on Windows 7 and using a pc, I built myself. My wireless card is one that comes with the Asus rampage extreme 5. I also note that wireless worked well before, but it only started happening since this morning.

  Any help is appreciated.

  Thanks for the help but it seems to have fixed itself until I could try your solution.

  Here is what happened. I restarted the pc with the cable is connected and windows downloaded 10 upgrade because I read on another forum Windows 10 Fixed a similar problem. Before I went ahead with the installation I disconnected ethernet to try your solution. And wifi works now. Updated willl if this happens again.

• Replace the internet Explorer by foxfire

  Internet Explorer is now my way to go on the internet. I want to end up with Internet Explorer and replace it with foxfire. I have problems with internet explore being frozen and started on my games and other places I could be. If I want to finish with internet explore and we rather foxfire
  
  bold text

  Simply install firefox and it starts, it should display the message "Do you want to use firefox as your default internet program", or something like that. Check the box and your done!

• Why static DNS server address round get the unable to download updates 8024402C problem in WIN7?

  I got a work around for the unable to download problem error 8024402C updated on a new laptop WIN7 Starter running.  I get regarding the size of the update and starts to download, but nothing comes down.  The solution is to change the DNS settings of default for a manually configured DNS server, for example 4.2.2.2.  It works, but I wonder why, and what is he moving?

  The auto setting worked when I was in the United States connecting via a LAN in the hotel but not here at home in AUS, where the settings auto search for an address DNS 192.168.1.1, my router ADSL/2.  All other functions like Skype, Adobe updated, download of MS shop, all work very well using 192.168.1.1.  Also my XP Home PC, all use 192.168.1.1 and they get the updates without any problem.

  -What is someone able to explain why?

  Thank you

  Hi ascidiens,

  The 0x8024402C error codes typically occur because there is an incorrect character in substitution of proxy settings. Basically, it's something to do with the proxy of your connection settings network and which can be overcome by changing the DNS settings in manual.

  Bad adjustment System (DNS) domain name of your network connection may also cause this error. Update Windows servers are accessible through DNS servers configured for Internet access. If a local DNS server has changed for some reason, the Windows Update client isn't able to find and connect to the Windows Update server.

  I would like to know if refer to a Microsoft article to work around this problem by changing the settings default for a manually configured DNS server DNS (Domain Name System).

  I would say to you to follow the steps mentioned in the link below for the complete solution of the problem

  0x8024402C error code when you try to install updates on Microsoft Update or Windows Update Web sites

  http://support.Microsoft.com/kb/900936/en-us

  Windows Update error 8024402C

  http://Windows.Microsoft.com/en-us/Windows7/Windows-Update-error-8024402C

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• What IP SLA probe for LDAP and Radius

  Hello

  I would use IP SLA probes to monitor client access to broadband.

  We want to deploy some routers of shadow on some Exchange sites to measure the customer experience.

  We are looking to create a DNS probe. We would like to test authentication.

  I think running the port of probe UDP 1812 for RADIUS.

  I don't know if that's enough.

  What is LDAP?

  Anyone would have done a similar implementation?

  Thank you

  Rgds

  Abdel

  There is no specific operations to test the Radius and LDAP. There is nothing you can do as the udpEcho operation will not work with the port of RADIUS for the RADIUS. You must configure the collector to send requests to the UDP echo (port 7) port or equipment of machine IP SLA (see http://www.cisco.com/en/US/docs/ios/ipsla/configuration/guide/sla_udp_echo_ps6441_TSD_Products_Configuration_Guide_Chapter.html ).

  However, for LDAP, you can configure a collector of generic TCP connection which will at least give you data connection latency. The collector must connect to tcp/389 (assuming the plaintext LDAP) or tcp/636 for ldaps.

• What means "Blacklist DNS reverse response searching for known malware domain spheral.ru - Win.Trojan.Glupteba (1:31600)"?

  I have a Cisco ASA5516x w / firepower with an IPS license installed and I'm trying to determine what means this Impact 1 alert:

  Reverse DNS BLACK list response searching for known malware domain spheral.ru - Win.Trojan.Glupteba (1:31600)

  The source looks like it's coming from DNS servers on the internet:

  208.67.220.220

  208.67.222.222

  4.2.2.6

  204.117.214.10

  The destination is our domain controllers that are configured to be our DNS servers. I'm just trying to understand what really means this alert? The classification is "a network Trojan has been detected", but this means that a user attempted to solve an to a site that has been reported as malicious DNS record, or they have malicious software on their PC that is trying to connect to a server command & control out in the wild? To be clear, the penetration of these alerts are outside interface and evacuation is our inside interface. If someone can provide a clear explanation for these alerts, it would be greatly appreciated. Thank you!

  Hello

  This does not necessarily mean that the PC or the DC are infected. This rule is for a reverse DNS lookup.

  With the source and the destination, it could just be a package that is the reverse DNS lookup query response. Now, why this request is sent in the first place is a question and a value of the investigation.

  flow: to_client; content: "|" 07. spheral | 02. ru | 00 | » ; fast_pattern: only;

  Download the capture of packages in the case of the rule, you can check and verify the IP address that is resolved to spheral.ru and then identify what PC initiated the request.

  Sometimes, it could be an AV product or security, try to reverse search DNS for an IP address of the suspect.

  Rate if helps.

  Yogesh

• DNS for internal sites in VPN

  Hello

  in my setup, I have an ASA 5510, which acts as a DHCP server, configure the dns client, allowing to solve two local addresses, such as myhost.mylan.local and external addresses, say cisco.com.

  If I connect with client VPN via UMTS, since I need to enable split tunnel, myhost.mylan.local try to solved in provider ISP UMTS, i.e. it is not resolved. How can I solve the problem, i.e. How do I resolved by local dns addresses?

  Thank you

  Hello

  you will need to configure the feature called split-dns

  The syntax is here:

  Split-dns {value domain-Name1 Name2-field domain-nameN | none}

  Then you will be able to resolve your myhost.mylan.local specified in split-dns and also on internet DNS names.

  HTH,

  Jan

• Cannot access internet or ping external site names

  I have a problem with a cisco asa 5505

  I'm unable to access the internet from any computer on the local network. I can access the network from outside, in fact I have rdp access to a server that has been installed with it. I can also ping external IP addresses, but no names. Here is the config. For any help or suggestion is appreciated. I'm starting to believe it's a DNS issue?

  : Saved
  :
  ASA Version 8.2 (5)
  !
  My - ASA host name
  domain monsite.fr
  activate the password * encrypted
  passwd * encrypted
  names of
  name description 192.168.10.x Srv - 192.168.10.x server
  name 97.7x.xxx.xx2 outdoor-home
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  192.168.10.x 255.255.255.0 IP address
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP outside-host 255.255.255.252
  !
  passive FTP mode
  clock timezone CST - 6
  clock to summer time recurring CDT
  DNS server-group DefaultDNS
  domain monsite.fr
  object-group service rdp tcp
  Description Office remotely
  EQ port 3389 object
  inside_access_in list extended access permit tcp any any eq 3389
  inside_access_in list extended access permit tcp any any eq www
  inside_access_in list extended access permit icmp any one
  inside_access_in list extended access udp allowed any any eq ntp
  outside_access_in list extended access permit tcp any any eq 3389
  outside_access_in list extended access permit icmp any any echo response
  pager lines 24
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 1 192.168.10.0 255.255.255.0
  static (inside, outside) interface tcp 3389 Prov-Srv - 192.168.10.9 3389 netmask 255.255.255.255
  inside_access_in access to the interface inside group
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 97.7x.xxx.xx1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.10.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Telnet 192.168.10.0 255.255.255.0 inside
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:eea8b18bfa5f73b832857913a77486d1
  : end

  you do not allow any DNS traffic leaving your network. Add the following and try again:

   access-list inside_access_in extended permit udp any any eq 53 access-list inside_access_in extended permit tcp any any eq 53

  In general, it was not necessary to allow DNS to the entire internet, only for the DNS servers used by your internal systems.

  Some other improvements to your config:

  (1) If you configure icmp-inspection, you can remove the ACE that allows to echo-replys unconditionally in your network:

   policy-map global_policy class inspection_default inspect icmp no access-list outside_access_in extended permit icmp any any echo-reply 

  (2) the outside AS to WHAT RDP could focus a little bit more:

   access-list outside_access_in extended permit tcp any host 97.7x.xxx.xx2 eq 3389 

• HP Envy TS m6-k015dx: HP Envy Bluetooth Windows 10 connectivity issues

  I've upgraded to Windows 10 recently (even if she will be as a downgrade) and have experienced problems with the wireless and bluetooth connectivity. specifically, I can't keep a solid connection on any wireless network while my bluetooth is turned on.

  He'll keep disconnection, and when he says that I have a stable connection I don't always get all internet.  He said that there is a problem of DNS probe.

  As well as wireless issue while bluetooth is turned on, I also had problems with the connection to an audio device via bluetooth.  I recently received Coulax QX8 bluetooth headphones and they connect on my phone (iPhone 6s), but when I try and connect to it on my laptop, it is not figure it out.  I activated the devices to the discovery of the notebook in the settings, but I still don't see it appear.  Help, please.

  And before all the messages about drivers, YES, I update my bluetooth and Wifi drivers, through both the HP Support help and directly by the driver and the Device Manager.

  Current drivers

  Bluetooth: Intel Wireless Bluetooth, version 18.1.1525.1445

  Wireless: Intel Centrino Wireless-N 2230, version 15.18.0.1

  Please let me know if bluetooth or wireless number, or if it's just with Windows 10 on this product!

  Hello @sambody47,

  Thanks for the quick response!

  Keep your eyes on Windows Update.  If ever the drivers become available for your product, it will be pushed through this program.  You can check this site for the drivers as well:

  HP products - where to find Windows 10 drivers and software for my model?

  Because Windows 10 drivers are not yet available for your product, on the site of HP; You can try to use the solutions on this site to work around the problem.  Please let me know the results:

  How to: install and update drivers in Windows 10

  If you're still having problems, try to use back to a previous generation option, in your system settings: HP Notebook PC - upgrade to Windows 10

  Remember that this feature is available only for 28 days, after the installation of Windows 10.  I hope this helps.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution' , this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Kind regards!