Does not start after change of memory.

Similar Questions

• Pavilion dm3-2020eo does not start after change of RAM

  As the topic says my computer does not start after a change of the RAM.

  I've updated 2 x 2 GB 2 x 4 GB DDR3 SO - DIMM 204pins Rams. When I start the computer after installing new RAM does nothing, all I get is a black screen.

  According to the Spec computers, it should be able to take up to 8 GB of DDR3 RAM.

  Can someone help me?

  Thank you
  Leo

  Here's the key:

  We're working on two sockets and one does not at all.

  You have a bad memory module. It happens very rarely, but it's not impossible to get a new stick of bad memory. Get the replaced bad and I think you'll be fine.

• My copy registered and checked for XP Pro SP3 does not start after changing the motherboard. Second problem is that I can't find my original install of XP Pro disc.

  After failing to find the source of reliable performance from my PC, I decided to bite the bullet and replace the motherboard, memory and the CPU. I installed a triple base 435 Athlon and a motherboard Gigabyte MA74GMT. Awarded PC again started the first time - but Windows will not, I get a number of options but none work - safe mode brings up several lines of messages on the partition of multi (0) disk (0) rdisk (0).

  A previous post suggested that a similar message meant some kind of malware but if I replace the old motherboard, processor and memory Windows works very well - in fact I use it now.

  Do I have an option but to reinstall Windows from a CD? Otherwise I have a problem - I can't find the installation discs for each piece of software except my Windows XP Pro! I do repair discs?

  Thanks for your help.

  Hi DaGeLi,

  · Provide us with the complete message you receive.

  Follow the methods below:

  Method 1:

  You were able to start the first time, you can try to boot to the last known good configuration and check the results. Link to get the procedure please refer to: how to start your computer by using last good known Windows XP Configuration:http://support.microsoft.com/kb/307852

  Method 2:

  If it doesn't then you can follow the procedure from the below mentioned link. As you do not have the Windows XP CD you can follow the procedure if you have already installed on the computer to recovery console

  How do I recover from a corrupted registry that prevents Windows XP startup:http://support.microsoft.com/kb/307545

  Otherwise, you may need to make the boot floppies. See the link for the procedure below:

  http://support.Microsoft.com/kb/310994

  You can also contact the manufacturer of the system to get the Windows XP CD.

  For reference: how to fix a computer that does not start:http://www.microsoft.com/windowsxp/using/setup/support/nostart.mspx#2

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think

• DHCP service does not start after change of vmnetdhcp.conf

  Hello

  My installation includes a host running windows 8.1 pro and guest is an Oracle Linux 6.5 with NAT. As I searched for a static IP address for the comments I went ahead and added the following to the end of vmnetdhcp.conf

  host computer2 {}

  Hardware ethernet 00: 0C: 28:D9:D5:95

  fixed address - 192.168.37.3

  }

  As soon as I try to restart the dhcp service falls down. Even if I just restart machine job changes, the DHCP service does not start. When I do a reset of the network through the network Publisher configuration and simply accept a dynamic allocation of IP address to things normal race comments. The same configuration works fine on Windows 7 Pro host. Any help would be appreciated.

  Hello

  Thank you for using our product.

  I tried the same set upward on Win7 and Win8.1 host, both of them work well.

  So I guess that there is a syntax error when setting up vmnetdhcp.conf.

  Maybe missing ';' at the end of each line?

  An example would be like this:

  host computer2 {}

  Hardware ethernet 00: 0C: 28:D9:D5:95;

  fixed-address 192.168.37.3;

  }

  Please check and try again with kindness.

  Thank you!

• Pavilion DV6-2140ED: Pavilion DV6: 10 Windows does not start after the upgrade memory (4 GB-> 8 GB)

  After I upgraded the RAM in my HP DV6 from 4 GB to 8 GB (2 x 4 GB Kingston KTA-MB1333 / 4G), Windows no longer starts. I get a blue screen and it keeps restarting.

  I think that the memory specifications are similar to the Samsung M471B5673EH1-CH9 original memory: Ghz 1333, non - ecc, 1.5 volts, case latency 9 etc.etc.

  It's a laptop DV6-2140ED HP with a processor Intel i5 - 430 m and Intel mobile chipset HM55.

  The bios detects 8 GB and it also passes the check/test of memory. As far as I know that I have also installed the latest bios firmware: F.1D. Reinstall my Windows 10 64 bit does not work either: with 8 GB I also get blue screens, after I try to boot my Windows 10 bootable USB drive.

  I read other people having the same problem, but I have not read a solution yet. What can we do about it?

  Hello:

  Please see this discussion.  You buy a very specific memory for any HP laptop with Mobile Intel 5 series chipset.

  http://h30434.www3.HP.com/T5/notebook-hardware-and-upgrade-questions/memory-upgrade-6550b/m-p/5340551/highlight/true#M207994

• OptiPlex 755 USFF does not start after changing the cmos battery

  I have a desktop Optiplex 755 USFF requiring the cmos battery to replace. After the replacement of the computer will not start. It brings up the menu windows start, the sasfe mode, safe mode with network set mode command prompt, security, last know good configuration and boot normally. Any option will bring to the top of the WIndows XP loading screen and then re-boot of the computer right back to the start screen. A big loop. I can get the hard drive to boot in an Optiplex GX280 without problem. I was told of the motherboard needs to be replaced, but I changed the units of the system and the same thing with this hard drive.

  I tried to reinstall the operating system and get all the way to "starting windows" and then the blue screen stop error message 0x0000007B (0xF7A10524, 0xC0000034, 0x00000000, 0x00000000) dead. The computer is WIndows XP SP3, 1 GB of ram with 80 GB hard drive. It seems that the Setup program does not recognize the hard drive.

  Any help would be appreciated.

  After several hours of experimentation, I finally found the correct BIOS settings in order to get the computer to boot. There are three BIOS settings that need to be changed or check settings by default so that it can work. SATA 0 must be activated, SATA operations must be changed from AHCI, ATA and in the modular Bay, by default "far-sighted" should be replaced by the IDE. Save the settings and start the computer to the right upwards.

• XPS 8700 does not start after the upgrade memory RAM

  Dear members of the Forum.

  I have a XPS 8700 with the following specifications:

  Core i7 4770 k

  2 TB HARD DRIVE

  16 GB of Ram (4 x 4 GB)

  NVidia GTX 660 (1.5 GB)

  BIOS version A10 (later).

  RAM sticks in my current system are all Micron Tech (here) 4 GB DDR3 SDRAM PC3 12800 240pin 1.5V 1600 MT/s.

  I had two RAM modules of tech Micron (here) 8 GB DDR3 SDRAM PC3 12800 240pin 1.5V 1600 MT/s so that I can move on to a total of 24 GB.

  After the discussion here and here, I installed the modules in slots 1 & 2 (both white) so that the system is not able to start. Not even got the bios screen. I also tried 3 & 4 configuration (both black) I ran my computer with the two 8 GB sticks only, with the same unfortunate results.

  I also saw that it is a normal problem of compatibility problems between the types of ram, but I consider that this is not the case. In addition, bad positioning of the modules is not also the case because if I put my old ram glue the computer starts normally.

  I used tape you will static isolation.

  Is the problem, a problem of compatibility between my computer and the RAM modules?

  If the RAM is damaged does these effects (do not start)?

  How can I check if the RAM modules are damaged?

  What would be your suggestions?

  I thank very you much in advance!

  Mauricio

  Hmm, I'd say you two bad sticks of RAM.  If the system POST even with them, I would swap them if you can.  We know that the RAM slots work because you have 4 x 4 sticks without any problem and your computer can take up to 32 GB of RAM.  Your admission that you bought the right kind of RAM, voltage, and speed, etc., so that shouldn't be a problem.  I would say as bad RAM.  When you do not install, just check that you make pairs in each of the colored slots, for example. matching pairs in the slot of white and black.

• Service does not start after change of IP address on the server of SRM

  Here is the log.  The IP address has been changed, but I don't know how to take the side of MRS.?

  Journal of VMware Site Recovery Manager, pid = 4064, version = version 1.0.1 build-128004 =, = release, section = 2 option

  Cannot create the writer console

  Value flush dir "C:\Documents and Settings\All Users\Application Data\VMware\VMware Site Recovery Manager\DumpFiles"

  The initialization of the DBManager

  Current working directory: C:\Program VMware Site Recovery Manager\bin

  TaskMax = 10, IoMin = 1, IoMax = 21

  Try DrExternalRecoveryApi

  Plugin path 0: dr-external-recovery - api dll

  Absolute path of the plugin 0: C:\Program VMware Site Recovery Manager\bin\dr-external-recovery-api.dll

  Try RecoverySecondary

  Plugin path 1: dr-secondary - recovery.dll

  Absolute path of the plugin 1: C:\Program VMware Site Recovery Manager\bin\dr-secondary-recovery.dll

  Try SanProvider

  Plugin path 2: dr - san - provider.dll

  Absolute path of the plugin 2: C:\Program VMware Site Recovery Manager\bin\dr-san-provider.dll

  Try TestProvider

  Plugin 3 path: dr-test - provider.dll

  Absolute path of the plugin 3: C:\Program VMware Site Recovery Manager\bin\dr-test-provider.dll

  DrExtApi Instance of Service is initialized.

  Plugin has started.

  'SanProvider' provider has MoRef 'dr.primary.SanReplicationProvider:PrimarySanProvider '.

  Registered provider 'SanProvider '.

  'SanProvider' provider has MoRef 'dr.secondary.SanReplicationProvider:SecondarySanProvider '.

  Registered provider 'SanProvider '.

  Plugin has started.

  ' Provider 'TestProvider' has MoRef ' Dr. PrimaryTestProvider:primary - test provider.

  Registered provider 'TestProvider '.

  ' Provider 'TestProvider' has MoRef ' Dr. SecondaryTestProvider:secondary - test provider.

  Registered provider 'TestProvider '.

  Plugin has started.

  LocalSite already installed - good!

  Vmacore::InitSSL: doVersionCheck = true, handshakeTimeoutUs = 120000000

  VC connection: connection as the user "administrator."

  VC connection: logged in session F5EDC747-1344-4F98-82FB-038BB9D42933

  The specification of proxy for extension com.vmware.vcDr points to 172.20.0.168, not to this host

  Check with the local VC server is not valid

  Initialization of service content: unexpected exception 'class Vmacore::Exception' record with the local VC server is not valid

  Application error: check with local VC server is not valid. Closing...

  Unable to send the request. A new attempt. Error: class Vmacore::CanceledException (operation has been cancelled)

  VMware-Dr. service stopped

  Z OS

  I tried this on my own server and that you couldn't make it work.  I ended up just reinstall SRM, keeping the same database - NBD since most of the settings are there anyway.  Later, I came across a blog (which I can't find now) that said that VMware supports only a reinstall after changing the IP address.

• 160 U does not start after changing from 4 to 8 GB Ram

  Hey community,.

  I just installed two new RAM DDR3 1066 MHz 7-7-7-20 204pin modules of Corsair SO-DIMM to improve my U160 somewhat. It runs a Win 7 Pro 64 Home and already has been improved with a Samsung 250 GB SSD.

  The BIOS indicates the RAM properly but no matter if I try for a normal start or economy mode, restarting the laptop once the windows colors appear when starting. 'Last known version' does not help, nor let him start via a bootalble pen which I also installed this version of Windows. Because there is no blue or black screen I guess it's not a physical problem, but a prob of victory.

  Someone an idea?

  Thanks in advance,

  Baschdel

  Maybe run mem test a bar at a time to see if its bad? run the test of mem on a USB drive or a bootable cd. Lenovo is known to support only a certain amount of ram, I guess to avoid problems and complications. It is not their problem if you exceed nominal max and it does not work.

  http://www.memtest.org/

• VCenter Service does not start after changing the port number

  Hi all

  Accidentally, I changed the port number for the Vcenter server from the portal of VCenter 10443 and dint realize that the Java application uses 10443 so.

  Could not start the server vcenter service, because its raise an error saying 10443 port is already im currently byt used another application.

  I tried to stop the Java service, in order to start the vcenter service and make changes to port again, numbers but I am unable to stop the java application.

  Please, if anyone knows how to change the number of Vcenter via config port or any other way, please throw a comment... Its much appreciated.

  Thank you

  Nirmal

  If you use the MSSQL database, locate WebService.Ports.http in the VPX_PARAMETER table and change to the correct port.

• Satellite Pro L40 does not start after changing the BIOS settings

  Changed some settings in the bios last night and now when I boot I get a screen black lights flash and hard drive lights up but nothing on the screen.

  There is no password on the bios... How would a BIOS reset to normal?

  I put a windows disc now, I hear the disc spin but nothing on the screen

  (I think that I have come to the right place on the forum)

  It s a Toshiba Satellite Pro L40 model psl4be.

  Thank you

  > There was no bios password... How would a BIOS reset to normal?

  You can set the default BIOS ONLY inside the BIOS access BIOS by pressing F2 or at the beginning of the initialization of the order

  But I doubt that this problem is related to the BIOS.
  Maybe it s just a simple bad luck that this problem happened exactly after change something in the BIOS.

  Try connecting an external monitor and check if you can see something on the 2nd screen.

• Computer does not start after changing permissionl

  I had bad to put files on my hard drive without signature every time. I have made some changes in permissions and must have inadvertently changed everyone to access, because now my computer will not boot. He gets the white Apple on black background and goes just about a third of the way and stops. Have I blocked the drive permanently. It doesn't have a cd/dvd drive, so I have no boot disk. It was running 10.10.5. The only thing I have is a USB key with 10.9 on it. Elbow of desperate here and I'd appreciate any help anyone could offer.

  jwm48

  iMac (27 inch, at the end of 2013)

  Click here and follow the instructions.

  (143633)

• Windows does not start after changing the partition with external software

  Hello

  I messed up and followed some bad advice.  Water under the bridge, but I want to recover my bootcamp partition if possible.  I've seen several messages with the right process, but decided to post hear instead of assumptions.  I am running OS X El Capitan on an early 2011 MacBook Pro.  My 256 GB SSD is a bit pressed and tried to be too stingy with the Boot Camp partition, so my current troubles after resizing.  I have 10 Windows on the bootcamp partition.

  I'm going to throw a bunch of data from my survey here.

  Capella: ~ list of the ronh$ diskutil

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 250,1 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_CoreStorage Macintosh HD 190,5 GB disk0s2

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database BOOTCAMP 58.7 GB disk0s5

  / dev/disk1 (internal, virtual):

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS Macintosh HD GB + 190,2 disk1

  Logical volume on disk0s2

  B6DC811B-004D-4245-83C9-8FAA0B51FD9E

  Unencrypted

  Capella: ~ list of cs ronh$ diskutil

  CoreStorage groups of logical volumes (1 found)

  |

  + Logical Volume - Group 487E3580-D1BE-4A6D-A33C-38C8DD8ABA34

  =========================================================

  Name: Macintosh HD

  Status: online

  Dimensions: 190546800640 B (190.5 GB)

  Free space: 19005440 B (19.0 MB)

  |

  +-< physical="" volume="">

  |   ----------------------------------------------------

  |   Index: 0

  |   Disc: disk0s2

  |   Status: online

  |   Dimensions: 190546800640 B (190.5 GB)

  |

  + -> 37BE876E-8E51-47C3-8D62-001EC021DE56 family of Logical Volume

  ----------------------------------------------------------

  Encryption type: no

  |

  +-> Logical Volume B6DC811B-004D-4245-83C9-8FAA0B51FD9E

  ---------------------------------------------------

  Disc: disk1

  Status: online

  Size (Total): 190175473664 B (190.2 GB)

  Reversible: Yes (no required decryption)

  Name: Macintosh HD

  Volume name: Macintosh HD

  Content indicator: Apple_HFS

  Capella: ~ ronh$ sudo TPG - vv - r show/dev/disk0

  Password:

  See the TPG: / dev/disk0: mediasize = 250059350016; SectorSize = 512; blocks = 488397168

  See the TPG: / dev/disk0: MBR suspicious to sector 0

  See the TPG: / dev/disk0: Pri GPT to sector 1

  See the TPG: / dev/disk0: GPT Sec at sector 488397167

  start index size summary

  0 1 MBR

  1 1 Pri GPT header

  2 32 table GPT Pri

  34 6

  40 409600 1 part TPG - C12A7328-F81F-11D2-BA4B-00A0C93EC93B

  409640 372161720 2 part TPG - 53746F72-6167-11AA-AA11-00306543ECAC

  372571360 1269536 3 part TPG - 426F6F74-0000-11AA-AA11-00306543ECAC

  373840896 1024

  373841920 114554880 5 part TPG - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7

  335 488396800

  488397135 32 table dry GPT

  488397167 1 dry GPT header

  of gdisk.

  Command (? for help): p

  Disk/dev/rdisk0: 488397168 sectors, GiB 232.9

  Logical sector size: 512 bytes

  Identifier (GUID) of disc: FD5932B4-069B-4CCE-A2EE-99AB5720CA17

  Partition table contains up to 128 entries

  First usable sector is 34, last usable area is 488397134

  The partitions will be aligned with the boundaries of sector 8

  Total free space is 1365 sectors (682,5 KiB)

  Starting number (sector) end (sector), Code name of size

  409639 40 1 200.0 of MiB EF00 EFI system partition

  2 409640 372571359 177.5 giB AF05 Macintosh HD

  3 372571360 373840895 619.9 MiB AB00 Recovery HD

  5 373841920 488396799 54.6 giB 0700 BOOTCAMP

  

  It is worth spending time to recover?  Thank you.

  Ron

  1. can you describe the problem and the steps you took to get here?

  2 can scroll you down to the next MS data (after that highlighted) and press 'p' to the list of files? Press ESC, once only, to return to this list.

• Re: Smoker L30-10 X PSL33E does not start after upgrading RAM

  Hello

  I have a problem with my laptop.
  It has 1024 MB of RAM (2 x 512), but it wasn't enough, so I decided to update to 2048 MB (2 x 1024).

  I bought two modules and my computer does not start after changing them.
  It was only a screen black (same BIOS has not started). I tried another combination of installation of memory modules RAM.
  2 x 1024 - did not work
  1 x 1024 - did not work
  1 x 1024 + 1 x 512 - working but not properly.

  BIOS find that I only 896 MB (1024-128 for the video card)
  I said OK. Let's see what will show windows. He was also 896 MB.
  I launched CPU - Z and it shows that the total size of memory is 1536 MB (medium detect both modules).
  I found that CPU - Z detect 1 module 1 024 MB and 512 MB secondary, but the BIOS detect only 1024 MB 1536. How is that possible?

  I have fought, is that my BIOS is old, then I update the toshiba Web site form most recent version, but the problem persists.
  Please someboy help me and tell what to do.

  PS. the Modules are new and work correctly.
  They have been tested.

  Hello

  Have you used two identical RAM modules?

  What kind of modules did you use?

  In my view, that the problem is related to the new, inserted modules.
  There must be something wrong with the modules or modules are not completely compatible if the laptop can not boot after installation.

  According to a few pages of the book handles the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM modules.

  Did you use these modules?

• Satellite A200 PSAEOE does not start after upgrading memory

  Hi, I am first time here.

  I bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB of RAM. I bought a pair of ram Corsair (2 * 2 GB VS2GSDS667D2). The computer does not start after that I installed the memory. I have intel 945 chipset, which is capable of 4 GB (manual page 1-2). The bios version is 1.8 2007.

  Can anyone help me, please.

  Post edited by: Marian ovidiu

  Hello

  The A200 series supports different chipsets;
  Intel 945 PM
  Intel 945GM
  Intel 943GML

  As far as I know your laptop supports the * 943GML * Intel chipset and the chipset supports 2 GB RAM max.
  Take a look at your laptop s user manual * Page 18.*

  Summer: 4 GB of RAM are not possible, and therefore your laptop does not start.