Double error NAT with Ooma

Similar Questions

• receive the error message with every new open tab

  Whenever I open a new tab, I get a popup error message. I have screen shots that can be granted.

  At first, I thought it was a mistake to Java, but I've uninstalled and reinstalled Java.

  There are two error messages which read:

  [JavaScript application]
  evalInSandbox:Error: Permission denied for <https://facebook.com> create a wrapper for the object of class UnnamedClass.

  [JavaScript application]
  Error: Permission denied for <https://facebook.com> create a wrapper for the object of class UnnamedClass

  So I clicked on help > troubleshooting information and choose Reset Firefox.
  Now I get a new error message with every new tab open.

  [JavaScript application]
  Error: syntax error

  Please tell us how to do this.
  Thank you
  JudyLeeThurber

  1. In the address bar, type Subject: config and press enter. The subject: config "this might void your warranty!" warning page may appear.
  2. Click on I'll be careful, I promise!, to continue on the subject: config page.
  3. Type browser.newtab.url
  4. Double click on the first result, a new window should now display.
  5. Type of topic: newtab in the area.
  6. Click ok and load a new tab. It now works of mireille?

• Help! Export error 27 with only a few videos

  I exported Final Cut Pro X projects directly on my external hard drive. I got an error 27 with one of them, and given that it is exported well I don't think it's a problem with my external hard drive formatting. All the videos have been imported in the same way and the same camera. Any ideas about why this is happening? Thank you!

  Most likely, you export a FAT32 / 'Windows' formatted the disk, right?

  error27 occurs when you attempt to save a file > 4 GB - that is not supported by fat32 (very old format..)

  So, small export projects, larger not. -.

  reformat the drive (erases all content!) to exFat or hfs + / "Mac"...

• I have Windows XP Media Center Edition Version 2002 with Service Pack 3 and I tried to run Media Center but I get an error message with ehshell.exe.

  original title: error with ehshell.exe

  I have Windows XP Media Center Edition Version 2002 with Service Pack 3 and I tried to run Media Center but I get an error message with ehshell.exe. Could you help me?

  This problem exists since the 1st Media Center. SP2 and SP3 had a difficulty, but it is obvious that it doesn't always. The same problem still exists in Vista today with a lot of other carried over from XP. System restore would work, but you do not have any good restore points so reinstall an operating system seems to be your only option.

  You probably don't want to do an OS reinstall you need for Media Center, but since it does not at all, you might want to play then remove the Media Center updates and or SP3 and reinstall them.

• error 80072F8F with windows updates.

  I run windows vista professional. have encountered error 80072F8F with windows updates. It also seems to have an impact on the renewal of McAfee. I'm not very wise computer & so very frustrated. McAfee has suggested that I have the problem of windows?

  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Update-error-80072F8F

  If Windows Update error 80072f8f during updates, date and time on your computer may not be identical to the date and time for the service online from Windows Update. Your computer and the service have no need to have an identical date and time, but if they vary too much it will prevent you from checking for updates.

  Make sure your internet box etc. is correct also.

  Read the entire article.

• X 230 error 1802 with the Correct WLAN card

  Recently, I ordered my brand new x 230 for the start of the University and selected the thought of WLAN card default option which would be sufficient for my needs. After the hand signal and dropouts, problems I decided to upgrade the WLAN card that would improve the signal strength.

  I know the existence of the 'white list' frustrating that means that some cards are allowed to use. So, I went in the store of Lenovo and looked for what was the best WLAN card that might come with a new order of a 230-System x, as surely they are on the whitelist.

  Later, I bought an Intel Centrino Ultimate - N 6300 card and installed correctly in my x 230. However, from the start I saw to my despair that the 1802 error was there, tells me my card has not been approved. Could someone explain how hell a card that can come already installed in x 230 is not did not whitelist checking?

  Needless to say I am not very satisfied with Lenovo, because I can't even find a list of what cards are accepted. What is the point in a white list anyway? I am a student trying to patch BIOS to remove it, but no one has yet done a patch.

  Why do I get an error 1802 with this card?
  Thank you.

  Hello and welcome,

  Doesn't have that 6300 come from the store of Lenovo, or from a vendor who said it was for a Lenovo laptop?

  The card type is not the whole story when comes to the white list.  In addition to the correct (6300) type by its PCI vendor and device ID, it must have an ID of subsystem of Lenovo.  (IIRC, it can be more precisely not the subsystem ID, but the effect is the same).  A generic 6300 will not work.

  A card must be sold by Lenovo or pass the white list.  Reputable suppliers will provide a number of Lenovo FRU (CRU) to check the FRU list for the machine.

  For example. Since the research database of Lenovo parts -> ThinkPad X 230page, the RUF for that 6300 is 60Y3233.  It was not easy to find.  The RUF are not in the hardware maintenance manual any more

  If your card has a number of Lenovo FRU, something else is in place.

  [edit] types andyP faster as I do...

  Z.

• I get this error message with my DVD player: "Windows cannot start this hardware device because its configuration (in the registry) information are incomplete."

  I get this error message with my DVD player: "Windows cannot start this hardware device because its configuration (in the registry) information are incomplete." I tried to reinstall the driver when the computer prompted me to do it, but there was an error with this as well. My computer will not all read the disks.

  Original title: Matshita DVD-R UJ 890

  Hi AJordanMiller,

  Try these methods.

  Method 1

  Run the fix - it from the link below.

  Hardware devices not detected or does not
  http://support.Microsoft.com/GP/hardware_device_problems

  Method 2

  See the help article:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/314060

  Registry warning: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  It will be useful.

• Static NAT with the road map for excluding the VPN

  We have problems of access to certain IPs NATted static via a VPN.  After some research, we have learned that you have to exclude traffic destined for the VPN to the static NAT using a road map. So we did this:

  10.1.1.x is the VPN IP pool.

  access-list 130 refuse ip 192.168.1.0 0.0.0.255 10.1.1.0 0.0.0.255
  access-list 130 allow ip 192.168.1.0 0.0.0.255 any

  sheep allowed 10 route map
  corresponds to the IP 130

  IP nat inside source static 192.168.1.5 1.1.1.1 sheep map route

  Above worked to fix the VPN but the IP 192.168.1.5 is no longer publicly available via 1.1.1.1.  What seems to happen, is that the static NAT is not really work and this IP address is NATted with the IP of PAT.

  Any ideas on how to get this to work?

  Thank you
  Diego

  Hello

  The following example details exactly your case:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080094634.shtml

  Try to replace the 192.168.1.0 subnet by the host address.

  It should work

  HTH

  Laurent.

• BlackBerry smartphones dreaded 0x3b21 error sync with Curve 8310 DM 4.7 on XP pro 3

  No joy with 4.7 DM to DM 4.6 (4.7 by the grip of way on the recording of "modules" when installing like 4.6 done so!)

  Here's the video:

  http://www.YouTube.com/watch?v=u6tS8vvokEM

  (I have many more like this for 4.6, the DM is facing problems in my humble OPINION)

  CK on:

  http://www.BlackBerry.com/BTSC/search.do?cmd=displayKC&docType=kc&externalId=KB01451&sliceId=SAL_Pub...

  (where is the Permanent URL of tracing?)

  I'm not alone in this struggle, so I hope that some will benefit from the demo above.

  I had no SUCCESS in sync my curve for more than two weeks... (I'm looking more to the Iphone and Android now).

  That said, I need of those in the know to decipher this cryptic message. In fact, I need a fix. Let someone else read this and tell me the solution or workaround.

  This is my journal of trace

  Mon Dec 15 20:36:59 2008 - Intellisync Log file.

  Mon Dec 15 20:36:59 2008: error loading system failed - {F64973FB-7CB0-460E-9DCC-36A023757617}.4151 a.\iluptbl.cpp line 245
  Mon Dec 15 20:37 2008: error loading system failed - {F64973FB-7CB0-460E-9DCC-36A023757617}.4151 a.\iluptbl.cpp line 245
  Mon Dec 15 20:37:03 2008: error 0 x 80040107-2147221241-2088370138 a.\olkfolders.cpp line 393
  Mon Dec 15 20:37:03 2008: error 0-2088370138 a.\olkfolders.cpp line 322
  Mon Dec 15 20:37:03 2008: error - 2088370138.0 at la.\OlkFolders.cpp line 152
  Mon Dec 15 20:37:03 2008: error 4237.4237 to la.\callback.cpp line 1103

  Landry says:

  I had the same error occur with DM 4.6 with my Curve 8310. I got the job of synchronization at the beginning, but it has stopped working shortly after. Once I made the debug log, I found the same error 0 x 80040107 a.\olkfolders.cpp. So I decided to create a new Outlook profile and switched DM to use instead and everything is good! Just to let you know, I couldn't even change the Configuration of the synchronization without seeing the error.

  I just got the phone recently so I guess while I was trying to understand the configuration that I had made a change somewhere in Outlook or DM and that caused the errors occur. DM uninstall and delete all settings are a complete waste of time.

  Create a new Outlook profile seems to be the fix for me. And like you, the uninstall has been a waste of time. Moreover, I had no joy with the edition of the Configuration of the synchronization without seeing the error.

• NAT with access-list

  Now,.

  I want nat by looking at the destination address.

  example if destination is A nat for x pool network, and if the destination is something different then nat to the pool of y.

  IOS supports natting with ACLs and road maps.

  but as stated in the order reference specifying acl is valid only for the nat 0.

  So how can I nat based on destination address.

  is it possible with pix?

  If so, how?

  Thanks in advance

  You can not do conditional NAT based on destination on the Pix address. The only way to achieve this would be to have several interfaces with itineraries that would send traffic for each interface, NAT them as appropriate.

• NAT WITH FLEXVPN

  Hello

  Please can someone tell me how NAT with flexvpn?

  I have a HUB to spoke and spoke to talk configuration with virtual-templates.

  When I configure NAT and do a traceroute to google the first hop ip address is the HUB router.

  but it must go directly to the internet.

  Thanks in advance,

  Topcu, M

  Take a look at the difference between the defined itinerary and accept the traffic.

  You're forcing the default routes... bad idea unless controlled :-)

  Start by removing the "any" declaration of access lists using road together.

• WINDOWS WITH OUTLOOK 13 8.1. MAIL server error RETURNED WITH MESSAGE 550.

  I USE WINDOWS 8.1 WITH OUTLOOK 13. MAIL server error RETURNED WITH MESSAGE 550. Please login to use this mail server. How can I do this?

  So that we can look into this further, please provide the affected email account and complements of NDR (or error), you received so that we can determine the cause of this problem. To do this, please follow the steps below:

  1 right click on the message to bounce on your Inbox.

  2 choose the option show message source on the menu drop-down. You will see a window containing the headers of e-mail messages and content.

  After doing so, to validate the source of the message with all components of the notification of non-delivery such as:

  > Final destination

  > Action

  > Status

  > Diagnostic code

• When downloading an app from the trial of creative cloud app error ocured with the message "Download appers corrupted.please try to download again(-60), please provide a guide step by step to solve this problem."

  When downloading an app from the trial of creative cloud app error ocured with the message "Download appers corrupted.please try to download again(-60), please provide a guide step by step to solve this problem."

  Contact adobe support using a Web browser that accepts cookies and allows pop up windows, click here and as soon as it is available, click "still need help," https://helpx.adobe.com/contact.html

• I installed my own copy of Lightroom 5 to 5.7. Now all files I try to develop gives me a message "there was an error working with this photo. What should I do?

  I installed my own copy of Lightroom 5 to 5.7. Now all files I try to develop gives me a message "there was an error working with this photo. What should I do?

  Thanks Tanuj

  My fault. I restarted my computer and everything is still OK

  Thanks again

  Paul

• When I try to publish, I get an error that says: "an unknown authentication error occurred with your AdobeID. (SHARED_UNKNOWN_ERROR)

  When I try to publish, I get an error that says: "an unknown authentication error occurred with your AdobeID. (SHARED_UNKNOWN_ERROR)

  You can try the solution in this discussion?

  An unknown authentication error occurred using your Adobe ID (AUTH_UNKNOWN_ERROR)