Dynamic endpoint with IP VPN point

Similar Questions

• Using dynamic PAT with IPSec VPN

  Hello

  I will say first of all thanks for reading this post.

  My goal is to create a dynamic PAT for 5 private host 1 ip address public, then to allow this ip address public 1 via an ipsec tunnel.

  I have an ASA5555 running on code 9.2 (1).  Here's what I have so far:

  network of object obj - 12.12.12.12 {mapped address}

  host 12.12.12.12

  object-group, LAN {address}

  host 10.0.0.1

  host 10.0.0.2

  host 10.0.0.3

  host 10.0.0.4

  host 10.0.0.5

  NAT (inside, outside) dynamic source LOCAL obj - 12.12.12.12

  First question - haven't set up that PAT correctly? I'm trying to PAT the local private addresses on the public address 12.12.12.12

  Now I would use 12.12.12.12 as interesting traffic and leave it in a vpn tunnel:

  access-list 1 extended permit ip host 12.12.12.12 object-group Remote_Network

  This configuration seems correct?  Is there another way to accomplish the same task?

  Thank you for your time.

  Looks good so far.

  But if this PAT is only for VPN traffic, then you can change the policy-nat NAT rule:

   nat (inside,outside) source dynamic LOCAL obj-12.12.12.12 destination static Remote_Network Remote_Network

• Align the dynamic MC with the alignment of High Point

  Hello guys, I have a doubt, if a step having a height of 600px and I would like to focus a movieClip with dynamic size and the registration point is always at the top, to the this 600px 400px how it is possible, without having to create another movieClip.

  To Center vertically align the movieclip, first of all, you must wait for dynamic movieclip is complete, then you can place the movieclip based on...

  MovieClip._y = (600 - movieclip._height) / 2

• Problem with Tunnel VPN L2L between 2 ASA´s

  Hi guys,.

  I have some problems with my VPN Site to site tunnel between 2 ASA (5520/5505).

  I watched a lot of videos on youtube, but I can't find out why the tunnel does not...

  Both devices can ping eachothers WAN IP address (outside interfaces), but I don't see any traffic between the 2 sites. It seems that the tunnel is not open to everyone. When i PING from the local to the Remote LAN (which should be an interesting traffic for the tunnel...), the its IKEv1 remains empty...

  Am I missing something? I can't understand it more why same phase 1 is not engaged.

  You NAT won't. In your config file traffic is NATted initially and then does not match any more crypto ACL. You must move the rule dynamic NAT/PAT until the end of the table on two ASAs NAT:

   no nat (INSIDE,OUTSIDE) source dynamic any interface nat (INSIDE,OUTSIDE) after-auto source dynamic any interface

• ENDPOINT WITH THE OPTIONKEY MULTISITE (HELP)

  Hello

  I have endpoint with a multisite option key registered to a VCS I do not control. When I signed up for the VCS with the endpoint with the option key of a different endpoint on the same subnet as I can not however, connect when I unregister endpoint with the down option of VCS, I can connect to this endpoint with no problem with an another endpoint. When I re - register endpoint with the option key pressed to the VCS I can not connect. My Network guy looked at the packages and told me that the first package of the endpoint that I use to connect to the endpoint with the option key send a packet to 1720, and then all the other packets are sent to the VCS I do not control. Sent VCS deny. Trying to find out why the endpoint that I use to connect to the endpoint with him becomes key option refuse SCVS.

  I think you're mixing a whole bunch of information that eventually causes you confusion.  There are two elements in play in your example.  To try to make it simple

  1. a license on a multisite endpoint (which allows you to make several simultaneous calls) through your call control mechanism chosen

  2. a call control mechanism being 'direct' or through the VCS.  You can have the two 'direct' and a 'VCS/guardian' in game at the same time.

  The best solution to your problem would be to talk to the one who manages the VCS you don't control and asking them to allow the 2nd endpoint to register as well - this way, your two units will be able to call each other, and one with the multisite license will be able to call several other end points at the same time (using its multisite license).  According to what other infrastructure is connected to the VCS managed externally, there may be other benefits to do so (calling other end points registered, the external call, managed directories, MCU, TCSes, etc. If they are available).

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Dynamic action with refreshment area interactive report

  Hello!
  
  I use APEX 4.02
  
  I have a page with 2 regions.
  Region1 is a form (of entry)
  Region.2 is an interactive report on the same table as region 1
  
  When you enter values in the form I'm trying dynmically similar research records in the table with the interactive report.
  
  I made a dynamic action on the change of form fields that must refresh the interactive report region. I can see this one fires if I add an alert to debug if it fires.
  The dynamic report is based on a query with bind variable pointing to the fields in the form, for example
  where
  Field1 =: P2_FIELD1
  
  
  It works fine on the page loading, so no action is triggered, but I see the lines in the region of report are the ones I'm looking for.
  The updating of the report area does not work, but it is never nice and/or showing the correct data after a change of form fields, if it looks like the dynamic action "refresh the region" does not work on the interactive report.
  
  Any ideas why it can go wrong?
  I want to solve this problem using standard dynamic actions and preferably not via PL/SQL or JS, should be possible if I believe documentation... ;)
  
  See you soon
  Bottom
  
  Published by: bklerk on 26-apr-2011 03:07

  Hello

  Check this example application
  http://Apex.Oracle.com/pls/OTN/f?p=39830:38

  You can download and check the source

  Kind regards
  Jari

• Cannot find the 'endpoint' with 'RemoteObject' property in Flex 3

  Hi all
  I am uttering the 'RemoteObject' class object inside the class action script. I'm here
  unabe to find ownership of "endpoint" with the remote object in Flex 3.0.I am currently using
  the SDK 3.2.Earlier I used this property earlier in Flex 2.0.Can whole body sugget me what
  is the replacement in flex 3 for this, or how to get this property.
  
  In Flex 2.0
  ===========
  var rm:RemoteObject = new RemoteObject;
  RM.source = "ServerSideClassName";
  RM.destination = 'amfphp ';
  RM. EndPoint =http://Ip or server PC/ProjectName/amfphp/gateway.php;
  In Flex 3 (sdk 3.2)
  ==================
  var rm:RemoteObject = new RemoteObject;
  RM.source = "ServerSideClassName";
  RM.destination = 'amfphp ';
  Cannot find rm.endpoint here.
  Thnx in advance
  Mayeul Singh Bartwal

  Hello Arnaud

  I m not sure but I think you used the remote object from the package of «mx.rpc.remoting.RemoteObject» class

  instead of "mx.rpc.remoting.mxml.RemoteObject. That's why is does not show property as the 'end point '.

  To verify remote call from the package «mx.rpc.remoting.mxml.RemoteObject» with the object

  May helps you

  Thank you

  Virat Patel

• Application with a decimal Point ID

  Hello
  
  We are in the process of migration of applications in an environment on APEX 3.01 to a new APEX 3.20 environment.
  
  On our environment old we had used decimals in our application ID i.e 100.1, 200.1 etc., this means we could keep all of our applications quite organized for example 100.x apps would be apps DEV, 200.x would be to TEST applications and 300.x would be PREPRODUCTION apps etc.
  
  When I got to install these applications in the new environment I get the following error message
  
  ORA-20001: GET_BLOCK error. ORA-20001: Execution of the statement was not successful. ORA-20001: digital invalid value 100.1 for the column ID of Application & lt; pre & gt; begin wwv_flow_api.create_flow (p_id = & amp; gt; 100.1, p_display_id = & amp; gt; 100.1, p_owner = & amp; gt;) "CS_APEX_DEV", p_name = & amp; GT; '* SSO Login', p_alias = & amp; GT; "SSO_DEV", p_page_view_logging = & amp; GT; 'YES', p_default_page_template = & amp; GT; 14915307666594361731 + wwv_flow_api.g_id_offset, p_printer_friendly_template = & amp; g
  
  I also get a invalid similar digital value error message when I try to manually create an application with a decimal point in the ID of the Application.
  
  Is this something that is no longer allowed withiin APEX or y at - it a parrameter which can be changed this will allow?
  
  Ian was soon

  Apex uses decimal notation to designate the translated versions of the application. I can't tell what dynamic translation of version was introduced, but it could be that you are running in. It seems you no more will be able to include a comma in your application ID.

• Just updated to Sierra and updated Pages at the same time. Now when I try to select a line of text I find myself with an insertion point where I stopped by selecting

  Today, I updated for Sierra and updated to the latest version of the Pages. Now I find that I am more able to select a line of text. When I try to do, I find myself with an insertion point where I stopped by selecting, but nothing is selected. This is a bug in the new version of pages or get my wrong settings?

  You use a Wacom tablet by chance?

  Solution: Press the shift key, just before stop selection. And Yes, that sounds like trouble in the Sierra.

• How can I find the music marked with an exclamation point in my itunes library?

  How can I find the music marked with an exclamation point in my itunes library?

  Hello there rdgernnr!

  I certainly don't want to find the songs that show the "!" and get them to play correctly. If you have not yet done it, read this article: If you see an exclamation point next to your items in iTunes - Apple Support

  More precisely:

  Correct the path of the media file

  Follow these steps to help find the correct location of the file iTunes media:

  1. In iTunes on your Mac or PC, select the song, album, movie, or television show that has the exclamation next to him.
  2. In the MenuBar at the top of your screen, computer or at the top of the iTunes window choose Edition > read the information.
     If you are using Windows and you don't see the menu bar, Learn how to turn it on.
  3. When you see a message asking if you want to locate the file, click search.
     • If you know the location of the file, point to it iTunes and try to read your content.
     • If you do not know the location of the file, search for it:
       Mac: Press ⌘ and space control your keyboard, and then type the name of the movie title, app, song, album or artist.
       Windows: Press the Windows on your keyboard, and then type the name of the movie title, app, song, album or artist. If your keyboard does not have a Windows key, press the Escape (Esc) and control (Ctrl) on your keyboard.
     • If the file is on a network drive or external, plug on the volume of disk or external network.
     • If you find your objects in the trash or recycle bin, restore them to their previous location:
       Mac: Control-click or right-click on the item and choose put back.
       Windows: Right-click on the item and choose restore.
  4. Once you retrieve the file, use Get new Info to locate the file, and then point iTunes to the correct location.

  See you soon!

• updating my iphone6 froze on itunes with an arrow pointing to itunes

  updating my iphone6 froze on itunes with an arrow pointing to itunes, what do I do?

  Connect the device to the computer and open iTunes and make restore

  This will get your device back

• I have an error: a drive with a mount point is required - what it means?

  I have an error: a drive with a mount point is required - what it means?

  Please explain EXACTLY what you were doing before this message appears.

• WiFi HP ENVY 4500 with several Access Points - same SSIS Configuration

  Hello

  We just got a HP ENVY 4500.  I have a main homenetwork with a wifi Modem/Router and an old router acting as an Access Point to the floor to extend coverage.

  Both have the same SSID and password and are set to different channels.

  My HP ENVY 4500 fails to connect when the Access Point is lit.

  It will connect with it.

  Once connected, I can turn on the PA and all is well.

  The two router an AP using WPA-PSK/WPA2-PSK encriptación

  The router (that it connects to) should have a better sgnal when both are on, so I do not understand why they need the AP to be turned off to connect.

  Any thoughts people?

  Eserim

  I think he has always had problems with several access points.  Try this, what ever AP is closest to the printer, set it to channel 1.  Then try channel 11.  Try now.

• Basic with yellow exclamation point features

  Hello

  My L412 supplied with Windows 7 Home Premium. I reinstalled Windows using a purchased Windows 7 ultimate DVD and I installed most of the software, but I still 3 devices basic system with yellow exclamation points on them.

  Here is a screenshot

  http://Tinypic.com/r/28j9loy/7

  Any ideas on how to fix?

  Try the driver of lenovo card reader

  http://www-307.IBM.com/PC/support/site.WSS/document.do?lndocid=MIGR-75277

• Chat on facebook-all I get is an icon in the shape of a yellow triangle with an exclamation point

  When I go on facebook, I have more a chat column. At the bottom right of the screen is a yellow triangle with an exclamation point. I do not happen to get on the chat at all.

  Hello

  A either be an add-on or something created by Facebook.

  Check with Facebook help and Support and their Forums.

  Facebook - help and Support
  http://www.Facebook.com/help.php

  Facebook - Facebook Contact and support of Facebook
  http://www.Facebook.com/help/?page=835

  Facebook - Forums
  http://getsatisfaction.com/Facebook

  ==============

  IE - tools - manage Addons - y at - it something listed there who might be in game?

  Start - All Programs - Accessories - System Tools - IE with no Addons - what works best?

  IE - Tools - Internet Options - Advanced - tab click on restore, and then click Reset - apply / OK

  IE - Tools - Internet Options - Security tab - click on reset all default areas - apply / OK

  Close and restart IE or IE with no addons

  not better?

  IE - tools - manage Addons (for sure disable SSV2 if she's here, it is no longer necessary but Java
  installs and it causes more questions - have you never update Java to go back in and turn it off again.) Search
  other possible problems.

  Windows Defender - tools - software explore - look for problems with programs that do not look right.
  Allowed are usually OK and "unauthorized" are not always bad. If in doubt about a program, ask
  topic here.

  Could be a free - SPYBHOremover - BHO - standalone program, needs no installation, download and run.
  not all are bad, but some can cause your question (toolbars are BHO).
  http://securityxploded.com/bhoremover.php

  How to change, add or remove startup programs in Windows 7
  http://www.SevenForums.com/tutorials/1401-startup-programs-change.html

  Also get Malwarebytes - free - use as scanner only.
  http://www.Malwarebytes.org/products/malwarebytes_free

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">