EA cannot Log in Smart WiFi 9500

Similar Questions

• Cannot access Smart WiFi in cascade mode

  I have the following Setup.

  My modem ADSL ISP is the main router with DHCP and its address is 10.0.0.138 who, for some reason, I can't change.

  I booked 10.0.0.1 for my EA2700.

  My EA2700 Port 1 is connected to my wireless Internet service provider router Port 1 creating a way of editing cascading of Lan-To-Lan.

  DHCP and NAT is disabled on EA2700.

  Both channels WiFi (2.4 GHz and 5 GHz) is defined with the same name and password so devices can connect to one of the routers and it works fine.

  The only problem is that I can not connect to https://www.linksyssmartwifi.com.

  When I connect to https://10.0.0.1 I can connect to my EA2700, but I get error 2113.

  Ignoring the error, everything works.

  I tried DMZ of 10.0.0.1 on my main router but it does not help.

  When a router WiFi chip is cascaded Lan to Lan you cannot remote access via WiFi Smart services.

• I can not connect to smart wifi router outside of the House?

  Hey.

  I need to portforward port for logging in my smart wifi router Linksys EA6500 from the House to the outside? I can only connect when I am om LAN or wifi...

  Another question: I can only connect to the same router using an application? Is there a way to connect via a browser?

  THX.

  When you have created an account for your WiFi Smart router, have you received a confirmation e-mail? Check your email and you must confirm it so that you will be able to use it. Refer to this link ofr more information: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=12e0e8fa76f340739d0cb72037819ca9_Creating__activat...

• EA2700 Smart WiFi unable to connect

  I can't connect my router via the Smart of Wifi utility EA2700.

  As soon as I put on the router, I used the CD it came with and attempted to implement. While I was in the range of the router and I can see it in my list wireless, I couldn't set it up.

  I came the usefulness and using the prompt of windows 7 I was able to change the SSID and I got a generic password.

  I was able to connect my laptop to the router with the password and access the internet.

  When went to set it up via the Smart Wifi utility using the same password I can't access it. My laptop is connected, but I can't access the router in the utillity.

  Directly, I have connected my laptop to the router with a cable right cat5 from the Ethernet port of my laptop to the port on the Router #1 and tried the utillity smart wifi. Still I can not connect.

  I tried to use that the IP 192.168.1.1 in the browser can still connect.

  I tried to use the CCC Web site still nothing.

  Prompt repeat me the invalid password, you mind right now I already have logged 3 more devices with the generic password.

  Any advice will be greatly appreciated.

  Have your tried using "admin" instead? You have not exactly set up the router using the Cisco Connect Setup Wizard, so the router password is not the same as the password of your wireless network. Login to http://192.168.1.1 or http://myrouter.local and use "admin" password. If you have upgraded the firmware on the router during installation, you can also go to http://linksyssmartwifi.com. Here, you can access the page locally (use 'admin' password again) or create a Linksys Wifi Smart account for cloud-base access.

• cannot log on as administrator with the password and open a user button session sends to the temporary profile.

  cannot log on as administrator with the password and log on user button wife sends him to temp. access to some of my articles on his desk.  She lost all access to his information.

  Original title: cannot log on as administrator with the password and log on user button wife sends him to temp. access to some of my articles on his desk. She lost all access to his information.

  Hello

  • Remember to make changes to your computer before this problem started?

  However, you can access the link below and follow the steps mentioned in the article and check if it helps you to fix the problem, and connect you to your normal user account.

  http://support.Microsoft.com/kb/947242

  I hope this helps. Let us know the result.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows Server 2003 cannot log on there are issas.exe message

  Windows cannot log in and display a message saying (issas.exe / service directory does not exist with the error No 1e0000...)

  Please help me my

  Hello

  I suggest you to send your request from the link and check.

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

• When my computor starts, the screen displays administrator profressionelle of windows xp, I don't remember the password I had used and cannot log - need help

  When my computor starts, the screen displays administrator profressionelle of windows xp, I don't remember the password I had used and cannot log - need help

  The solution is here:

  http://support.Microsoft.com/kb/321305?WA=wsignin1.0

• Screen saver turns on (Windows XP SP3) and lock the computer and the user cannot log back with their credentials without administrative rights

  When the screen saver is used and the user returns to open a session.

  they get...

  This workstation is in use and has been locked.
  The workstation can only be unlocked by user123 or an administrator.
  Press CTRL + ALT + DELETE to unlock this workstation.

  user123 cannot log back in. unless he made a system admin an administrator connections or user must reboot the machine to reconnect.

  Hello

  -Is the computer connected to a network domain?

  Please follow the steps mentioned below and get back to us with the results.

  Cannot lock a "locked" computer administrator.

  http://support.Microsoft.com/kb/242917

  Registry warning

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows

  For more information, see the link below.

  Information about unlocking a workstation

  http://support.Microsoft.com/kb/281250

  If the computer is connected to a domain, I suggest you to post your questions in the TechNet forums.

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  I hope that helps!

• When I try to connect my computer with XP operating system, I get this error message to: rund1132.exe and cannot log out.

  original title: log question.

  When I try to connect my computer with XP operating system, I get this error message to: rund1132.exe and cannot log out.  How can I fix?

  Hi KERRYYX,

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You have security software installed on the computer?
  4. What is the full error message that you receive?
  5. Are you able to restart and shut down the computer?

  It is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  You cannot log off, restart or shut down your Windows XP-based computer

  http://support.Microsoft.com/kb/831431

• Windows XP Professional help... Cannot log on to windows.

  Help!  Thanks for the reply... but it is all foreign to me... I bought the computer from a former place of work so did not any windows disk. I was unable to move forward on a blue screen that reads: a problem has been detected and windows has shut down to prevent damage to your computer. If it is the first time that you, ve seen this stop error screen restart your computer. If this screen appears again the following steps. Disable or uninstall the anti virus, the fragmentation of the disc or utility backup. Check your hard disk configuration and search for updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Technical information STOP: 0 x 00000024 0 X 00190203 0X82F42108 0XC0000102 0x00000000

  Can't do everything above that cannot log on that I think I should do... but not sure that I am not IT savvy. I've tried rebooting and without success.

  This basically means that I have to get the windows disc and reinstall? If so what do I lose all my docs photos etc... etc... th the computer?

  Forward the response and thanks in advance.

  Pete

  When you start windows, before the XP loading screen is displayed, press F8, and then select Safe mode.  See if you start a computer desktop, if it isn't you can run chkdsk /f in command prompt.

  If you cannot start in safe mode, you will need to reinstall (or try a repair installation) and Yes, you will lose this data, although there is a way to back it up.  You will need to download ubuntu and burn it on a cd and backup to external media.

• cannot log in to Firefox

  cannot log in to Firefox as some microsoft help site, I get the XPCOM error, I have tried every fix on youtube, none does not work for me

  I don't want to reinstall firefox, I would lose all my favorites.

  Ray

  cannot log in to Firefox as some microsoft help site, I get the XPCOM error, I have tried every fix on youtube, none does not work for me

  I do not want to reinstall firefox, that I would lose all my favorites.

  Ray

  https://support.Mozilla.org/en-us/KB/export-Firefox-bookmarks-to-backup-or-transfer

  https://support.Mozilla.org/en-us/KB/restore-bookmarks-from-backup-or-move-them

  Kind regards.

• Can X 3500 be a Smart Wifi router so

  I recently bought an annex X 3500 DSL A + combined router.  I don't see this router appointed under the list of Smart Wifi.

  This firmware can be upgraded to have full feature smart wifi?

  Hi anseetha, there no WiFi Smart firmware for X 3500 when I checked the Linksys support site. Linksys introduced 6 routers WiFi Smart. You can check it out here: http://www.linksys.com/en-us/smartwifi?icid=Linksys-Home-Networking-HN-FF-smart-wifi-link

• Question has Smart wifi

  I had my account smart wifi on my ea6500 but I just upgraded to wrt1900ac and now I see both routers on the account. How can I delete one of them? Thank you in advance.

  Leo2005 wrote:
  I had my account smart wifi on my ea6500 but I just upgraded to wrt1900ac and now I see both routers on the account. How can I delete one of them? Thank you in advance.

  Try this. Disable your account for a few seconds so that your email address will lose the connection he has with both routers, and then reactivate your account and associate the new router (WRT1900AC).

• How to remove several networks in the Smart WiFi Linksys

  I hope this is the right place to ask this question, if not please me foregive. I recently replaced my router with a WRT1900AC and after installation, I use my account for smart wifi Linksys to the Manager of this router that I used with my old Linksys router. However, when I noticed two other networks listed as to connect to networks of connection. They do not connect what either and I think that they are of my old router (I used the same network name). How do I remove these? They do not seem to be causing the problems, but are confused. Thanks in advance for any help!

  Ken

  Hello! Articles on the following link will help you remove the existing networks on your computers, portable devices or game consoles: http://www.linksys.com/us/search?text=remove%20networks&type=support_faqs

• Need help with the Smart Wifi EA6400 association

  I set my router several months ago using the password provided with the Quick Start Guide. I have never changed the password. I have implemented all our family computers, laptops and iphones using the same password and have never had any problems of access to the internet. Two weeks ago I put in place our new Sony smart tv by using the same password without any problem.

  Until today, I had never set up a Smart Wifi account. Now that I did it, I can't associate my router on the account. He repeated to me that my password is not valid. How this can be when I was able to implement using this password. Even the properties of the router is showing this same password. I am trying to get into the router to set up a password for comments.  After reading a bit on the forums, I have even tried using "admin" and which was too disabled. I am at a loss here and need advice on how to proceed.

  Hi Stormy_01. By combining the Smartwifi account to your router, do not use the password you use to connect wireless. It should be the password to access the router configuration page. By default, the password of the router is "admin". If it does not, then go to this page I gave in the previous answer and click on the 'Forgotten password' option that should send you the link on how to reset the password of the router to your email.

  Furthermore, the rest of wireless devices are connected properly and are now working through the router, is that correct? If so, then we only need to focus on the recovery of the password in the configuration page or edit if you can access your settings. If all else fails, your last option is to reset the unit and start from scratch.

  Liezl-10104

  Linksys technical support