EliteDesk Pro 800 G1: USB 3.0 BIOS Driver Windows 10 - Support

Similar Questions

• I installed Windows XP on my new computer (with Windows 7 PRO), but my USB does not work on Windows XP. It works fine on Windows 7

  I installed Windows XP on my new computer (with Windows 7 PRO), but my USB does not work on Windows XP. It works fine on Windows 7.

  Hello

  And much more: (XP mode requires professional, Ultimate or Enterprise).
  

  Get all the benefits of Windows 7 and continue to take advantage of your investments and more
  business and productivity programs that require a PC running Windows XP.

  Note: Windows XP Mode requires a download.
  http://www.Microsoft.com/Windows/Windows-7/features/Windows-XP-mode.aspx

  Windows XP mode
  http://www.Microsoft.com/Windows/Virtual-PC/Download.aspx

  Windows XP Mode is supported through Technet

  TechNet - Forums - Windows 7 virtualization
  http://social.technet.Microsoft.com/forums/en/w7itprovirt/threads

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Satellite Pro M70 - compatibility USB to RS232

  With the latest version of the BIOS and 2 RS232 totally different USB adapters, I can't get the RS232 interface to communicate with the laptop. The adapters are operating satisfactorily at least 3 other computers (1 of these loaptops was 2 door USB).
  I am running Windows XP Pro.

  Any help would be appreciated gratefully.

  Hello

  I searched the net for similar questions and a lot of people say that the converter could not work because of the SP2.
  I m not 100% sure about this, but it of possible.

  I found this page:
  http://www.Sabine.com/Sabine-professional-audio/USB-connection.htm
  On this page you will find some adapters tested and good work.

  Maybe it helps a little.

• Satellite Pro L10-103 - USB ports not working not

  Hi, my Satellite Pro L10 - 103 USB Ports do not work. I tried different things and finally my Advisor rubbed my computer clean of all programs and operating system. After reloading of the set up disc and having lost my dear some programs I am no further forward. It still does not.

  Anyone know if this means that it is a mechanical problem with the computer? (I use Windows XP). Your help would be greatly appreciated.

  Hey Buddy,

  As wrote Akuma did you use the Toshiba Recovery disk or the Microsoft Windows disk?

  After installing XP, make sure that Service Pack 3 is installed. It contains important updates and can be downloaded on the official page of Toshiba.

  In addition, try to remove all the USB ports on the Device Manager, restart the computer. Ports will still be recognized and ready to use once.

• Re: Satellite Pro A200 - black screen after the BIOS screen

  Hello
  I'm new to the forum and have a big problem. So, any help is welcome and appreciated.

  My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor. Also just as the screen goes black a beep can be heard which shows windows boot.
  I can access the toshiba Setup screen but not the installation of security mode.

  Kind regards

  Hello

  You wrote that you can access the BIOS, but have you checked if the HARD drive is recognized properly? Perhaps because the computer cannot start HDD isn't recognized then you should check this.

  If the HARD drive is recognized, I would try a Toshiba Recovery disk recovery facility. It seems that Windows isn't able to start and if you reinstall the whole system should help get rid me of this. Go to the start menu and select the CD/DVD drive as a boot device.

  Check this box!

• Ports Satellite A135 - S2306 defective USB after the BIOS update.

  OK, I searched all over the internet and not found anyone else with this same problem, or anyone with a solution that worked for me.

  A few weeks ago, I had the common error of the BIOS reset itself and asking for a password at startup. I took my local Toshiba authorized repair center, and they have not taken care of him, no problem.

  Since the resume, however, all 4 of my USB ports have been going crazy. What happened in the following three steps (in order):
  -One of the ports does not work at all, won't provide any current or even recognize that nothing is connected.
  -The 3 remaining ports are now only recognized as USB 1.1 ports, not USB 2.0 as they were before.
  -Now, only a very small number of my devices is not at all, with three USB mouse and two unrecognized hard drives work (I get the error message "USB device not recognized" standard Windows when I connect them to one of the three ports).
  I am running Vista Home Basic (32 bit) with SP 2 and the new version of the BIOS is v1.60.

  Is this something people of repair caused when they have unlocked the BIOS and updated? Is this a problem with the new BIOS itself? Any help would be GREATLY appreciated! Let me know if I let him out any relevant information, I tried to be as complete as possible. Thank you!

  The old Duke

  Hello

  > What is the repair people caused when they have unlocked the BIOS and updated? Is this a problem with the new BIOS itself? Any help would be GREATLY appreciated! Let me know if I let him out any relevant information, I tried to be as complete as possible. Thank you!

  It is not easy to say. I think that would be best to ask guys why it happens or what they have done in the past.
  But have you set the default BIOS?
  Please do; access the BIOS (by pressing F2). Set it to default by pressing F9 (I guess) and save the changes. Restart the unit.
  Access the Device Manager, and then remove all hubs USB and commands from the list of devices. After that reboot the device again. Windows should recognize the devices deleted again.

• Can I use Yoga 3 Pro to charge USB devices (phone, Tablet, iPad, etc.) when I'm far from an outlet?

  Is Yoga 3 Pro a giant USB battery pack?

  Yes, the Yoga 3 Pro IS a giant USB battery that can charge USB devices is not plugged into an electrical outlet.

  • How does it work?

  The USB port on the right side of Yoga can be configured to be "Always On". Go to the application settings of Lenovo, and powered on, there is a slider to allow him.

  • The 'Always On' USB port stay on when Yoga 3 Pro is unplugged?

  Yes, he does.

  • Always on USB port:

  

• HP Pavilion DV6-2007so: how to make bootable flash USB/CD, with bios WINFLASH bios?

  Hey,.

  IM that flashing caps lock and light above pg up / end keys. No picture at all on internal LCD or an external monitor with VGA connection. No beep at all. Fan turns on, seeing the battery is stable, DVD player works with green light etc.

  I tried Hard reset / cleaning of motherboard and processor + apply new thermal paste / boot without battery / different ram sticks on various slot machines etc. of usual bugs with no luck.

  The code is 2 blinks on NumLock and caps lock shift then 3s break and again 2 blinks, I looked on the HP site it means the bios corruption and just tried to do the restore bios with Windows + B + power button several times, laptop stays on for 10 seconds and restarts and Flash again to 2 continuous or blink code flashes (cpu failure). but 90% of the time of his flashing 2 x and then a few second break.

  I tried to make it bootable bios update usb by following this link:

  http://support.HP.com/us-en/document/c02693833

  Winflash for dv6 2007so files is downloaded those and installed, it starts the utility of update of the hp bios that should give the option to make bootable usb with bios file.

  Once isntalltion simply opens the... insyde bios flash program and asks me to Flash the bios.

  So how can I make automatic start bios update with the other computer?

  THX in advance

  Download the latest HP Diagnostics of material PC 3-in-1 USB stick available in the links below:

  http://WWW8.HP.com/us/en/campaigns/hpsupportassistant/PC-DIAGS.html

  and create the USB and read page 14 in 'Guide the user to the USB HP PC Diagnostics - Rev 5 (version March 2015) - English' existing document in the USB.

• Envy of HP dv6 7252er: laptop keyboard doesn't work anymore, any usb in the BIOS menu and start. In Windows, it works

  Recently, the keyboard no longer, no usb, in the BIOS menu bottled in the menu where you choose the Safe Mode boot. It's when you start the laptop, I press F10, it works in the BIOS, and is not a button doesn't work, the time comes, while the BIOS does not work. Also bottled menu at startup, I press F9, comes in bottles menu, but can't decide where to begin, arrows and enter does not.
  Laptop HP Envy dv6 7252er, a month or two ago, it worked.
  I must say, the night went to remove battery CMOS (Bios), bios folded, reinstalled windose. Did not help. In most windose, keyboard works.
  Any suggestions of what to do, or what could be the problem?

  PS Google translator

  The problem is resolved. Flashed the BIOS.
  Keyboard does not not in the BIOS menu and booth. Windows worked.

  After flash it worked.
  For flashed using the key USB Flash Drive and Windows + B. Image from the installer.

• Connection cricket MSGM8 phone USB on my laptop (running Windows XP Pro) run the Add New Hardware Wizard, but cannot find drivers

  Original title: badminton MSGM8 phone to the USB port on my laptop to pis draft.exe

  connecting a phone to cricket MSGM8 USB on my laptop (running Windows XP Pro) run the Add New Hardware Wizard, trying to locate the software for Qualcomm CDMA Technologies MSM, but can not find the drivers, any fix?

  Hi ChristopherStout,

  (1) what is the complete error message you receive?

  (2) is limited only to Cricket MSGM8 phone?

  Method 1: Run the fixit available in the article below and then check if it makes a difference

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive
  http://support.Microsoft.com/kb/925196

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base.
  How to back up and restore the registry in Windows

  Method 2: If you provided drivers\software disc from the manufacturer of the computer, go ahead and install it.  You can see the steps outlined in the article below

  How to troubleshoot unknown devices listed in Device Manager in Windows XP
  http://support.Microsoft.com/kb/314464

• Officejet Pro 8500 a - USB installation problem

  I can't get my PC to 'see' the 8500.  I can get as far as the USB, but the PC login window does not recognize that I have plug in the USB cable.  I've tried different USB ports on the computer, but it's exactly the same.

  I tried all the suggestions and procedures on the HP site, and the last of them is to go on the forum - I'm here!

  I use XP Pro Service Pack 3, and the printer is 8 hrs old.

  Thanks for your advice, but the problem appeared just to heal, even the next morning.  I gave him another chance, more exasperated than hope and he comes to connect!

• Is there a driver for Intel Pro DSL 3200 USB E$ xternes Modem?

  Microsoft has a driver for Windows 7 or 8 for an Intel Pro DSL 3200 USB E$ xternes Modem? All I can find are the drivers for Windows XP or 2000?

  William

  Intel device > driver Intel.  I doubt that it is a driver updated for such an old device.  You can try to install in compatibility mode, but that may not help.

  To install in compatibility mode do the following:

  Click with the right button on the installer > properties > compatibility > choose OS

  http://Windows.Microsoft.com/en-us/Windows-Vista/make-older-programs-run-in-this-version-of-Windows?SignedIn=1

• Corsair Flash Voyager GT 32 GB USB 3.0 thumb drive does not work after the upgrade to Windows 8 Pro

  Hello

  Since the upgrade of my Windows 7 Ultimate SP1 x 64 Windows 8 Pro x 64, my Corsair travel GT 32 GB USB 3.0 Flash USB key no longer works when plug it into my USB 3.0 port on my laptop. I get an error that the "peripheral last USB connected to the computer has malfunctioned and Windows does not recognize it." I looked for someone with a similar problem and came across this answer:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/Sony-microvault-USB-30-8gb-thumb-drive-not-working/8815a9bd-ee62-41EC-8116-a2a03d6f2bbf

  I tried the solution (method 1) on this page, however, Windows reports that it was unable to solve the problem of equipment.

  Is there anything else I can try to solve this problem? The USB key works in the USB ports 2.0, and it worked in the USB 3.0 port when you run Windows 7 Ultimate SP1 x 64.

  Kind regards

  Andreas Ball

  Hey, I contacted Corsair about this, and they say that it's a driver problem in Windows 8 and I need contact my laptop computer manufacturer for the latest drivers for it, but even if my manufactuer are full steam advertising upgrades of Windows 8, they say they do not support it fully yet...

  The host controller my laptop use of USB 3.0 is 'Renesas Electronics USB 3.0 Host Controller'.

  Through Googling, I noticed others have had problems with this host controller in Windows 8, and I can't seem to find a solution for it yet.

  Unfortunately, windows 8 compatibility is not listed then try to install the installer of renesas usb 3.0 in windows compatibility mode 7.

  complete list of supported products and the operating system:

  http://eSupport.Sony.com/us/p/SWU-matrix.pl?upd_id=6382

  Renesas Electronics USB 3.0 Host Controller®
  http://eSupport.Sony.com/us/Perl/SWU-download.pl?MDL=VPCL213FXB&upd_id=6382&os_group_id=6

  Download here: http://s02.download.sony.com/US/pc/RNDUSB-00241028-0042.EXE

  What does this do?

  This utility installs the originally shipped version of Renesas Electronics USB 3.0 Host Controller driver.

  This driver also solves the yellow exclamation point error that can appear in the device as "Universal Serial Bus (USB) Controller" Manager that indicates that the driver is not installed for this device.

  The products and operating systems (view all...)
  Model:
  VPCL213FX/B
  Operating system:
  Windows® 7 64-bit

  IMPORTANT: This file is only for use with the identified models. Not all models are sold in all countries.

  Important notes

  During the installation of this file, be sure that you logged in as an administrator or as a user with administrative rights. To ensure that no other program interferes with the installation, save any work and close all other programs. The taskbar must be clear of applications before proceeding. It is strongly recommended that you print these instructions for reference during the installation process.

  Download and Installation Instructions

  To ensure that no other program interferes with the installation, save any work and close all other programs. The taskbar must be clear of applications before proceeding. Download RNDUSB-00241028-0042. EXE a temporary of the file or download directory (Please note this directory for reference). Go to the directory where the file was downloaded, and then double-click RNDUSB-00241028-0042. EXE file to start the installation. The "User Account Control" screen, click 'yes '. On the screen "Select Country", select the country for the installation and then click on "next". To the "Renesas Electronics USB 3.0 Host Controller version 2.0.26.0" screen, click "next". The "License" dialog box, read the contract, then, if you agree, click "I agree" to continue the installation. The "Complete" screen, click on "Finish". Installation of the Renesas Electronics USB 3.0 host controller is complete.

• Satellite Pro A300-1E7 - USB Sleep and charge does not

  Hello

  I tried all the settings I can think off, but I can't seem to get the USB sleep and work load. My OS is Windows Vista Business SP1.
  I tried the mode 1, mode 2, unchecked power save all the boxes in hubs usb root, legacy usb support turned off but still the load stops when I put the laptop to sleep.

  Someone at - it a solution?
  Thank you

  Hello

  NOT all USB ports provide the features of sleep & Charge.
  THAT the USB port with the little icon flash supports the costs of sleep &.

  So I recommend you to check if you have used the correct USB port!

  Cheers mate

• OfficeJet Pro 8500 Wireless USB mass storage driver

  I can not print!  Get a message to solve the problems that tells me that the USB Mass Storage Design driver is not installed.  I can not install one of the original, or HP website software.  No matter what I do the driver will not be installed correctly.  I deleted my printer to my computer and then reinstalled and still I get the same message.  The printer worked fine for about three months and now I suddenly have this message.  I'm NOT tech savvy, so please if you answer make it simple.  I need an answer as soon as possible: this occurs at the end of my exercise and have loads of work that I need to get out!  Thank you very much.

  Click Start and type cmd in the box start the search.
  Right-click on cmd in the list programs, and then click Run as administrator.
  If you are prompted for an administrator password or a confirmation, type your password or click on continue
  At the command prompt, type the following command, sfc/scannow , and then the Enter key.
  When the analysis is complete, test to see if the problem you are experiencing is resolved.