Equium M50 - 192 - I get nothing on the monitor

Similar Questions

• Equium M50 - How to get down to the keyboard?

  How to get off the keyboard?

  Hello

  You want to replace the keyboard or what?

  The keyboard is fixed with 2 screws. The two screws are hidden under the cover of thin plastic above the F1 - F12 key
  You must remove this plastic, thin cover to access these screws

  But note; the keyboard is connected to the motherboard with a flat cable, you will need to do this first of all unplug until you can remove the keyboard completely

• Equium M50-192 blocks - BSOD THREAD_STUCK_IN_DEVICE_DRIVER

  I have an Equium M50-192 and get a blue screen and an error message saying infinite loop.
  The microsoft error report brings up to http://wer.microsoft.com/responses/Response.aspx/11/en-gb/5.1.2600.2.00010300.3.0?SGD=c7ea1371-98d3-4da2-98f2-61636f184296#here

  Error message: STOP 0x000000EA THREAD_STUCK_IN_DEVICE_DRIVER (Q293078) link - http://support.microsoft.com/?kbid=293078

  I'm pretty sure it means there is a problem with the ATI display driver but maybe wrong - ideas?

  Have tried to use the toshiba site to download the driver for it, I'm obviously a little distraught that while I can download and extract the files I don't know what to do next in fact update driver.

  Can anyone help?
  My laptop goes down all the time thanks to this and I already ran the recovery disks, but the problem still keeps recurring.
  Its adoption by trying to play a dvd and I have not yet tried to play since this first error, but it keeps recurring.

  Any help much appreciated

  See you soon

  Stuart

  Hello

  I completely agree with Akuma. If the same error occurs after installation of recovery it seems to be a graphics card problem.

  Before turning to an authorized service provider, you should try to update the BIOS. You can find it on the Toshiba site.

  If the new version of the BIOS doesn't help, you need help from the ASP. Maybe the motherboard should be replaced.

• Upgrade the HDD in Equium M50-192

  Hi all

  I have a laptop Equium M50-192 with the HDD 60 GB MK6021GAS inside.
  Does anyone know if I can improve it with the hard disk of 120 GB MK1646GSX.

  I found the site http://www.storage.toshiba.eu and I checked the two discs; but I don't know if the MK1646GSX disk has a compatible interface type.
  I am confused about the differences between ATAPI/IDE (60 GB MK6021GAS) and Serial ATA (120 GB MK1646GSX).

  Basically can anyone tell me if the 120 GB MK1646GSX will work instead of the 60 GB MK6021GAS?

  Any help gratefully received.

  Zoe

  Hello

  There is a big difference between the IDE HDD and the SATA HDD interface!

  Equium M50 supports the IDE interface and only IDE hard drives are compatible.
  You can use a HARD drive that supports IDE ATA-6 interface.

  In addition, you should know that the BIOS supports a HARD drive size limitation. This means that not all HARD drive sizes are supported.
  In my opinion the 120 GB should be ok but it s just my personal suggestion. You know? ;)

  concerning

• Beep codes Equium M50-192

  Hello

  I have a laptop Equium M50-192, who decided to stop working.

  I get 4 short beeps when I turn it on. The power led lights and fans start but the screen does nothing.

  Where can I find beep codes mean?

  Thank you
  Dan

  Hello

  It's not easy to say what could be wrong. Beep codes usually appear because the computer MESSAGE fails.
  If the Unit falls down the POST (Power on self test) beep code indicates which is originally the laptop does not pass the POST.
  The problem is that the bee codes are not standard and each BIOS provides different meanings of postcodes!

  As far as I know your device was shipped with Phoenix BIOS if you can try to google a bit for the Phoenix BIOS post codes.

  However, for most hardware failure is responsible for these problems. You can try to check the functionality of memory modules.
  Remove the simple modules and check if some of the memory fails.

• How to reset my Equium M50-192 to factory settings?

  Hi, I'm looking for some advice on my laptop.

  My laptop is a Toshiba Equium M50-192 and I would like to reset to the factory settings (on the box).

  I was advised by a friend that I need a recovery disk, but I don't seem to have one. Again, I have everything that came with the laptop when I bought it and have the different discs that came with it, but no recovery disk and have not been able to find the information I need the user manual.

  Is there a way I can reset my laptop without a disc?

  Any information or advice would be greatly appreciated.

  > Is there a way I can reset my laptop without a disc?
  It is not possible to reset to factory without reinstall drive settings. You have only one option: get Microsoft WXP installation disc and install the version of the OS.

  All the drivers, which you can download from the Toshiba support page.
  You can also try, it is to find if someone has the original disc of recovery for this machine and ask if you can get a copy.

• Equium M50-192 - upgrade to Windows 7

  I have an Equium M50 - 192, model No. PSM59E-003008AV, running on XP.
  My PC is Windows 7 and I have two machines on the same OS.

  Windows 7 Advisor on the Microsoft website shows that this M50 - 192 is suitable for an upgrade.
  I have already increased the memory to 2 GB.

  However, when I checked the Web from Toshiba site for pilots, there seems to be no driver Windows 7 for M50 - 192.

  Means that I can not upgrade to Windows 7?

  Hello

  Of course, you can install the Win 7 OS even if Win 7 drivers are not available for this unit.

  From my experience the Win 7 automatically looks for drivers and in most cases, the drivers are automatically installed in my case I didn t need to install the display in addition driver Win 7 found the drivers during the installation and process installation

• Equium M50-192 DVD & cd Format questions

  I have an EQUIUM M50 192 with program DVD + rewritable, but when dounlowding photos from the computer on a DVD in order for playback on other media, it won't work

  WHY?

  Hi Mich

  It's not easy to say why it doesn t work. I put t know what program brining you use and what DVD media you are using but it possible s that your use not taken in charge that the media or that you have not closed the session of engraving, etc.

  As you can see, there are many possibilities. I use the Nero burning rom software for burning CDs and DVDs. I also created a photo DVD to watch on the TV and it works perfectly.
  You should test this program. Maybe you're successfully.

• Equium M50-192 - startup problem

  I have a recently purchased EQUIUM M50-192 who developed a problem starting, a week after the purchase. To try to put the following happens
  Press the button power
  Turn on the light appears
  H/D light access appears
  CD-ROM flashes twice
  Then cut the power

  It passes through this sequence also if I open the lid, which suggests that the pc is in standby, IE opening the lid starts above sequence, as if you press the power button / stop.

  The same happens to a power supply (shows, seeing attatched and battery charge indicator) or only to batteries, also tried with battery but running.
  Have tried boot boot from CD via the F12 key and power at the same time but no luck with that, as mentioned above, I think the computer think it is somehow sleep and does not need to access the restore normal startup sequence. Can't find anything in the documentation re this implies a fault. Currently may not resume as collateral as abroad with out the paperwork he's come up with, for the next 6 weeks.

  Any ideas?

  Thanks in advance

  Hi, have you tried to remove the battery and then put back? Is also the adapter work correctly is the status light indicate a complete change?
  If you still not the laptop so that it starts then you don't have much choice but to the send it to Toshiba for investigation.

  Richard S.

• Equium M50-192 does not start

  Hello
  I posted a question here earlier on my laptop and I had useful assistance but he juices do not appear to have sorted.
  but I have now no wat it is not and just don't need to know wat it is

  I have a toshiba m50-192
  and when I turn it on it does not start going to a black screen and gives me errors (pxe - e61)

  in my last question, I was told that it was the hard drive was dead.
  Since then, I've replaced my hard drive and my hard drive, but it always seems to be doing almost the same

  I can get into my bios and the hard drive is recognized.
  I tried to boot from the disk recovery and hard drive but no joy.

  but since I replaced both drives when I boot from the hard drive it gos just a black screen with the little line in the upper right corner.

  but when I boot from the disk it gives me this error pxe - e61, which is where his tent to boot from the network I have read.

  until I replaced my hard drive, he had a strong look that has disappeared since I replaced it.
  the disk hard im trying to use now is off my brother's mobile which all ready installed xp on it it would make a difference when you try to boot from the hard drive? (my laptop is xp)

  I read something on definition of my hard drive to the master and my cd player to the slave that would make a difference and how would I do?

  I think it's as much information im aware off

  could someone please help as im stuck and did not have any idea what to do

  Post edited by: domio
  o im also getting the and pxe - e61 pxe - m0f error code

  Hello!

  What happens to an error you get? Please post what we can help you.

  To be honest that I n don't know what you mean with clip Ribbon keyboard but if the keyboard is faulty or something else, the keyboard completely must be exchanged. You are not a unique key or something else.
  If you want a new keyboard or other spare parts contact your local ASP.

  Good bye

• Equium M50-192: battery issue

  Hello

  Basically, my problem is that whenever my laptop battery is in and I also have the AC too, the battery automatically takes over from HQ if the battery is flat. Ive had only the laptop about 2 months and it started only recently to happen.

  Alternating current only also up a little battery, and then stops to load. And to top it off the laptop sometimes just turns off by itself when its only run off ac power. Worsened in the last week and now I cant charge the battery upward and the computer laptop is always just turn off so I can use the laptop yet.
  Before you suggest it, I tried to take the battery and the ac and them plug it back and also tried to use only the ac with the removed battery but there has been no improvement.

  It's very frustrating because I take care of property (I rarely move) and it has been great so far.
  I think it's probably a claim, however I thought I'd see if anyone knew what was wrong with it or if someone had the same problem and what they were doing.
  If anyone has any useful info on this it would be very welcome.

  Richard

  Hello

  Looks like a malfunction of the accumulator :(

  Discovered some days ago, I read on the Exchange battery Toshiba voluntary programs.
  Likely to be affected battery Pack may not properly load or unload.
  I checked this site and found the Equium M50 on the list.
  HTTP://EU.COMPUTERS.TOSHIBA-EUROPE.COM/CGI-BIN/TOSHIBACSG/GENERIC_CONTENT.JSP?SERVICE=EU&ID=0610_BATTERY_EXC HANGE_LANDING_PAGE

  The affected batteries were sold in some laptops manufactured between March and May 2006
  I think you should contact Toshiba service partner for the verification of the laptop and the battery and I think that you get a spare part.

  Good luck

• Equium M50-164: IE does not display the pages correctly

  I have a new Toshiba Equium M50-164, but it does not correctly display the my internet page at http://myweb.tiscali.co.uk/lorne.anderson/Bridge/

  It should look like this:
  http://myWeb.tiscali.co.UK/Lorne.Anderson/NormalView.gif
  with the bridge in the header, but on my Toshiba anaylser logo, it looks like this:
  http://myWeb.tiscali.co.UK/Lorne.Anderson/ToshibaView.gif

  I have 4 other computers all display correctly (under XP, 2000, 98SE) and several of his friends say they can see OK. If I look at the HTML unlying by right click and view source in IE the fuse that displays the logo should read:
  "align ="left">".

  
  
  
  
  
  
  "
  but on the Toshiba, view poster source:
  "align ="left">".

  
  
  
  
  
  
  "
  Note the blank line 2 where the code to display the logo should be. If I open the page of the files on my hard drive it is displayed correctly so my guess is that Toshiba have done something to the security IE by default overide settings but I do not see what. How can I get IE on my Toshiba to work how Microsoft has designed to work?

  Just like a check, anyone who uses this forum can read the page correctly, or you also get the missing logo?

  Hello

  Is this single page where you have this problem? Have you tried to open it with another browser?

  Try to install the latest updates. Perhaps the problem will be solved.

• Equium M50 - E-mail Message to update the WLAN driver

  Hello, I got this message. When I tried to check what is the right driver, I was told, there isn't one!
  Could someone please advise others that I wouldn't confuse my machine

  Thank you

  -Original Message-
  From:
  VOX
  Sent: Tuesday, March 18, 2008 09:41
  Topic: Site Web de Toshiba alert

  >
  >
  >
  >
  > Hello,
  >
  > Here is the latest software updates for your machine:
  >
  >
  > PC: Equium M50 (PSM59)
  > Type: Wireless Lan driver
  > Language: universal
  > Operating system: Windows XP
  >
  > Click on this link to read the full article.
  > http://uk.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_driver_details.jsp?ID=58122&OSID=10&drive rLanguage = 42 & selectedLanguage = 13 & driverCountry = 41 & selectedCountry = 8
  >
  > Click this link to find compatible drivers
  > http://uk.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp
  >
  > If you wish to unsubscribe from these alerts by e-mail, please click the link below to edit your profile on the Toshiba site.
  > http://uk.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/jsp/login.do
  >
  >
  >
  >
  >
  >

  There are not a lot of advice. WLAN new driver is available and if you want, you can update. If you are satisfied, how the WIFI network for the moment no one you don't have to do anything. Leave it as it is.

  WLAN drivers, you can find under http://aps.toshiba-tro.de/wlan/ and download whenever you want.

• Equium M50-216: cannot save or use the microphone or "phone entries

  I have an Equium M50-216, with 1 GB of RAM & Centrino 1.7 GHz processor, running XP Home.

  Without apparent reason, I am suddenly unable to use my SKYPE USB ' phone to talk. Audio output is perfect, however.

  I also tried my helmet using the jack on the front of the laptop, with the same result.

  I downloaded and installed the latest driver for the sound card, which is a Realtek AC97. I tried the test equipment of Windows, but there is no evidence of entry he built in sound recorder, audio, or in windows.
  The device driver is properly enabled and reported no problems.

  Is it a hardware problem - as it seems card works OK for output?
  Is it a Windows problem - I can achieve a reformatting the drive & re-install of XP soon - it would help?

  Roger.

  [email protected]

  Hello

  As far as I understand your problem, you are not able to use the external microphone. Am I wrong?
  You mean that it's a hardware problem, hmmm I n t think so.
  To me, it looks like a wrong setting

  Please check if the microphone is activated. This should be verified in the--> sound & audio devices Control Panel.
  On the volume tab, press the Advanced button.

  In the options settings, you can switch between the playback volume controls & record.
  Please check everything!

• M50-192: screenshots does not to the bottom of the screen

  Hi hope someone can help I have an m50 192 and had since 28/02/2006 the laptop has never even left the House and I have a problem with the screenshots.

  It does not take the screen down in the position of transit to myself as an engineer it resembles a spring broke off the stop screen capture I think it is a defect of design due to the short time I got the laptop.

  I have no extra but guaranteed insurance. I contacted them and they said, it was my fault.

  any help please
  Chris thompson

  Hello

  Well, I put t think that it s a design flaw.
  However, if you have the Toshiba service partner guarantee should solve this problem.
  I think that without tightening the screws holding this mechanism are responsible for this problem.

  If you have experience in the booklets, you can remove media from the image of the screen and check the screws. If you do, be careful!