Error-1073807202 lack of Code Library in open VISA

Similar Questions

• Why do I get VISA code error-1073807202 when you try to connect the PXI-2565?

  I got the 1703807202 error code (a code library required by VISA is not found) every time when I start the computer and used 'Initialize with topology' first connect my channels.  This error could disappear if I start MAX and open devices and interfaces, then re - perform the same task.  How can I get rid of the error?  Thank you.

  My bad, GPIB driver has not been installed

• LM500 error-1073807202 old VISA Open in LM - 500 Initialize.vi - > Operate.vi LM-500

  Hi all

  I am new to using labVIEW and I would be really grateful if you could help me with an error.

  I'm trying to control a model LM-500 liquid cryogen level monitor (Discontinued).

  Its drivers are available online and I download and I'm launching the demo.

  When I try to run it I got the following error:

  code error-1073807202

  Former VISA Open in LM - 500 Initialize.vi-> Operate.vi LM-500

  The LM-500 is connected to my computer through RS232 serial.

  I don't know what could be the error. I would appreciate if you could give me an idea about it.

  These are the drivers:

  http://www.cryomagnetics.com/drivers/LM500LV6_1.zip

  Thank you very much for your help

  That's because the new VISA open does not recognize the IO senior class, you must remove and replace it with the new type. Right-click on the resource of visa > Create > control.

  Select the rigtht COM port and try again

• My browser is blocked for security reasons. Code error-QFR5000RT11C. My incoming connections in open State distance. Then I got the call from the United States 1 (866)986-3669, I picked up the phone, but they put the phone down. No matter what? Help, plea

  My browser is blocked for security reasons. Code error-QFR5000RT11C. My incoming connections in open State distance. Then I got the call from the United States 1 (866)986-3669, I picked up the phone, but they put the phone down. No matter what? Help, please.

  It's probably a SCAM.  Do not call these numbers.  Force Quit Safari and reopen it by holding down the SHIFT key.

  Ciao.

• Errors open VISA 1073897360, 1073897343, 1073897229

  I use labview to send commands to a function AFG 3022 tektronix generator.  My VI uses a loop for the frequency exemple.25 kHz (starting at 1 kHz) every second by 15 seconds.   All two iterations of my loop, one of the error codes which I enclose below appears (stop the loop) and references the error occurred when opening VISA in VI initialize.  This VI just initialize the driver of instruments for the AFG3000 function generators series.

  I'm not sure that the error is with the VISA Open function or initialize the VI.  If the error is due to the VISA Open function, while this means there are problems with communication with my function generator and the Dell laptop that I use?

  

  What I tried:

  -cords of different USB 2.0

  -updated the driver for USB hub root

  -made sure the box in the USB hub root properties saying "allow this computer to turn off this device to save power" is not checked

  -put a second wait function 2 before VISA Open

  I will now try run the VI on another computer and will updated on how it goes.

  This is the VI initialize:

  

  I just found the problem. It had to do with the driver error on VI, who had a close function of visa.  Therefore, the constant closing and reopening of visa generated errors. I also moved the VI initialize out of the loop (as you suggest) just to be sure. Thanks anyway.

• Loading of the DLL string using the Code Library function node

  I experience now with the element of Code Library function node... what I wanted to do are, for example, I have compiled a. DLL file... which has a function that returns the pointer to string... function looks like:

  / * This function returns a pointer to the character string * /.

  char * pchar (int n)

  {

  char * str [] = {"error", "String1" and "Word2", "3"};

  Return ((n! = 1) & (n! = 2) & (n! = 3))? Str [0]: str [n];

  }

  but when I load into LabView DLL, a part of the chain on the screens to Panel frontal trash... any ideas why?

  p.s. when I do even with integer values... say my job is like int x = 5; Return x; and then I load in LabView to the digital indicator... it works great!

  So any ideas?

  thanx

  Cyrax says:

  I experience now with the element of Code Library function node... what I wanted to do are, for example, I have compiled a. DLL file... which has a function that returns the pointer to string... function looks like:

  / * This function returns a pointer to the character string * /.

  char * pchar (int n)

  {

  char * str [] = {"error", "String1" and "Word2", "3"};

  Return ((n! = 1) & (n! = 2) & (n! = 3))? Str [0]: str [n];

  }

  but when I load into LabView DLL, a part of the chain on the screens to Panel frontal trash... any ideas why?

  p.s. when I do even with integer values... say my job is like int x = 5; Return x; and then I load in LabView to the digital indicator... it works great!

  So any ideas?

  thanx

  You cannot return a pointer to the data stored on the stack. At the time when the function returns, the stack is reset to the State before the call to the function and in a multithreaded as LabVIEW environment probably long reused for other things when LabVIEW gets around to actually copy the returned pointer data.

  Since it is a read-only variable, you could create a permanent memory for string storage by declaring your variable static. This will create a memory area allocated globally for the string data (and also cause a compile error when you try to write in this area somewhere in your code, which is a good thing).

• lack of PIDOCOB6.dll cannot open the program

  lack of PIDOCOB6.dll cannot open the program of old software from microsoft for photos

  lack of PIDOCOB6.dll cannot open the program of old software from microsoft for photos

  =========================================
  The article Microsoft Knowledge Base that address the
  Question of PIDOCOB6.dll are no longer available, but I think
  the fix was to uninstall/reinstall Picture It!.

  Also... the error could be related to a printer driver... If you
  recently installed a new printer or your printer driver update
  It is maybe at fault.

  Sorry that's all I have on the subject.

  There is a Picture It! Group on Yahoo Groups... maybe
  could someone offer a few ideas:

  A_Picture_It_Help · Creative with Picture It & SOAK!
  http://tech.groups.Yahoo.com/group/A_Picture_It_Help/

• Win 2003 error - try to add and remove windows components I get this error. IIS.dll Setup library could not be loaded

  When you try to add and remove windows components I get this error. IIS.dll Setup library could not be loaded, or function OcEntry could not be found. code error 0x7e is on a system win 2003

  Hi MickRl,

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• popup message each startup (boot) - error while unpacking program, code 2.

  I have two messages popup one after the other, after each startup (boot)... it appeared after by mistake, you tap install updates day & shutdown, at first men... Please bear in mine, I have not upgraded to SP2 now have SP1... I think the required updates SP2... sometimes to invite me to install SP2, but refused.

  VISTA Ultimate 64-BIT

  1 MESSAGE POPUP
  "Error while unpacking program, code 2" Please report to author. »

  2ND MESSAGE POPUP AFTER CLOSE FIRST POPUP
  "An error occurred when loading library commonforms.dll::RegisterWindow

  It may have been removed. Please reinstall the Application. If the problem persists contact technical support. »

  Hello

  Have you made changes on the computer before this problem?

  I would suggest trying the following methods and check if it helps.

  Method 1:

  Put the computer in a clean boot state, then check if that helps you.

  How to solve the problem by running the clean boot in Windows Vista:
  http://support.Microsoft.com/kb/929135

  Note: Once you have completed troubleshooting, perform the steps in the step 7: to reset the computer as usual.

  Method 2:

  Run the Microsoft Safety Scanner and check if there are any threats found.

  Microsoft safety scanner: http://www.microsoft.com/security/scanner/en-us/default.aspx

  Note: If no threat found check if the file is necessary or not, then delete it.

  Also make sure that the popup is secure and then install if necessary. Windows updates are all secure and this is only the computer and Windows manufacturer. Optional updates are the manufacturer of the computer and the manufacturer of the application that you have installed. Important updates are Microsoft and it must be installed. I also suggest you try to install Service pack 2 on your computer and check if that helps.

  Learn how to install Windows Vista Service Pack 2 (SP2):

  http://Windows.Microsoft.com/en-us/Windows-Vista/learn-how-to-install-Windows-Vista-Service-Pack-2-SP2

  Hope the information is useful.

• How can I solve the error 2503 and 2502 codes when you try to install a program?

  When I try to install a program I get the error 2503 and 2502 codes, what should I do to get rid of them?

  2438651 how to solve problems that may occur when you install, uninstall, or upgrade a program on a Windows computer

  http://support.Microsoft.com/kb/2438651

  Also:

  Unregister Windows Installer and then reregister Windows Installer. To do this, follow these steps:

  1. in the menu 'Start', click on ' execute:.»

  2. in the "Open" box, type "msiexec /unreg", and then press ENTER.

  3. in the menu 'Start', click 'run '.

  4. in the "Open" box, type "msiexec/regserver", and then press ENTER.

  -----------------

  Check your hard drive for errors:

  Click Start

  Type: CMD, according to the results, right-click CMD

  Click on "Run as Administrator"

  At the command prompt, type: chkdsk /f /r

  When you restart your system, your computer will be scanned for errors and will try to correct them.

  --------------

  then

  Click Start
  Type: CMD, according to the results, right-click CMD
  Click on "Run as Administrator"
  At the command prompt, type: sfc/scannow

  This will check for any breach of integrity

  Restart your system

• Error 0 x 80010108 photo library

  Original title: probably the virus?

  c:\windows\TEMP\nsz3AFF.tmp specified in the Inbox start is not valid... have also staple of my icons opening error 0 x 80010108 photo library

  Hello

  Have you made changes on the computer that might have caused the problem?

  You can follow the provided methods to solve the problem.

  Method 1: When you run an .exe on a Windows XP, Windows Vista or Windows 7 computer file, the file can start another program

  http://support.Microsoft.com/kb/950505

  Method 2: Let's try to isolate if the problem came from the library corrupt related files. Try to repair by following these:

  1. press Windows + R, type AppWiz.cpl, and click OK.

  2. Select Windows Essentials 2012/Windows Live Essentials, click Uninstall/Change.

  3. click on fix all Windows Essentials programs.

  Method 3: The Microsoft Safety Scanner virus scanner

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Method 4: Remove temporary files.

  1. Click Start, search, and then click Find files or folders
  2. In the named box, type *.tmp to find all files ending with tmp.
  3. Check that look at the search box section points to the C: drive and the Document records.
  4. Click Find now
  5. Delete all files that are found

   

  You can also download the latest version of photo gallery.

  http://Windows.Microsoft.com/en-us/Windows-Live/Essentials

  This should solve the problem. If still you face the same problem, I suggest get back to us with the results of these troubleshooting methods and any additional information in what concerns the

• Get the linker error when executing our code in InDesign CC

  Hello

  We are modernizing our plug-ins for Adobe InDesign CC. In that we are facing a problem (the linker error) when running our code,

  1 > AssetCustomView.obj: error LNK2019: unresolved external symbol "public __declspec (dllimport): virtual __thiscall DVControlView: ~ DVControlView (void)" (__imp_? 1DVControlView@@UAE@XZ) referenced in the function __unwindfunclet$? 0AssetCustomView@@QAE@PAVIPMUnknown@@@Z$0

  1 > AssetCustomView.obj: error LNK2019: unresolved external symbol "public __declspec (dllimport): __thiscall DVControlView::DVControlView(class IPMUnknown *)" (__imp_? 0DVControlView@@QAE@PAVIPMUnknown@@@Z) referenced in function "public: __thiscall AssetCustomView::AssetCustomView(class IPMUnknown *)" (? 0InCatAssetCustomView@@QAE@PAVIPMUnknown@@@Z)

  1 > AssetCustomView.obj: error LNK2001: unresolved external symbol "public: class virtual IPMUnknown * __thiscall AbstractControlView::QueryInterface (class < struct PMIID_tag > IDType) const"(?) ". QueryInterface@AbstractControlView@@UBEPAVIPMUnknown@@V? $IDType@UPMIID_tag@@@Z)

  1 > AssetCustomView.obj: error LNK2001: unresolved external symbol "public: virtual void AbstractControlView::AddRef (void) const '(?) __thiscall. AddRef@AbstractControlView@@UBEXXZ)

  1 > AssetCustomView.obj: error LNK2001: unresolved external symbol "public: virtual void AbstractControlView::Release (void) const '(?) __thiscall. Release@AbstractControlView@@UBEXXZ)

  1 > AssetCustomView.obj: error LNK2001: unresolved external symbol "public: class virtual IDType < struct WidgetID_tag > __thiscall AbstractControlView::GetWidgetID (void) const"(?) ". GetWidgetID@AbstractControlView@@UBE? AV? $IDType@UWidgetID_tag@@@XZ)

  1 > AssetCustomView.obj: error LNK2001: unresolved external symbol "public: class virtual PMRect const & __thiscall DVHostedWidgetView::GetFrame (void) const"(?) ". GetFrame@DVHostedWidgetView@@UBEABVPMRect@@XZ)

  1 > AssetCustomView.obj: error LNK2001: unresolved external symbol "public: virtual void __thiscall DVHostedWidgetView::Resize (class PMPoint const & short)" (?) Resize@DVHostedWidgetView@@UAEXABVPMPoint@@F@Z)

  1 > AssetCustomView.obj: error LNK2001: unresolved external symbol "public: virtual void __thiscall DVHostedWidgetView::Invalidate(class PMRect *)" (?) Invalidate@DVHostedWidgetView@@UAEXPAVPMRect@@@Z)

  1 > AssetCustomView.obj: error LNK2001: unresolved external symbol "public: virtual void __thiscall DVHostedWidgetView::Show (short)" (?) Show@DVHostedWidgetView@@UAEXF@Z)

  1 > AssetCustomView.obj: error LNK2001: unresolved external symbol "public: virtual void __thiscall DVHostedWidgetView::Hide (void)" (?) Hide@DVHostedWidgetView@@UAEXXZ)

  1 > AssetCustomView.obj: error LNK2001: unresolved external symbol "public: virtual void __thiscall DVHostedWidgetView::Enable (short, short)" (?) Enable@DVHostedWidgetView@@UAEXFF@Z)

  1 > AssetCustomView.obj: error LNK2001: unresolved external symbol "public: virtual void __thiscall DVHostedWidgetView::Disable (short)" (?) Disable@DVHostedWidgetView@@UAEXF@Z)

  Help us please if anyone has idea about this error.

  Thank you

  Vimala L

  Hi Vimala L,.

  under Windows, you need to add the DV_WidgetBin.lib library to your library includes or just use $UI_PLUGIN_LINKLIST macro that contains this library.

  On Mac, it is included in the framework.

  Markus

• Error "the application"Steam.app"is not open more."

  I use Steam to play games, I recently installed Trove which began to hang Steam (and not run) rarely when I clicked on the play button.

  Sometimes, when Steam closes (or hangs in my case), when I try to open it again, it gives me an error "the application"Steam.app"is not open more.". It can be fixed by restarting, but it's boring and useless. How can I fix it?

  Restart the computer in safe mode. Some caches maintained by the system will be rebuilt.

  Safe mode is much slower to start up as normal. The next normal boot can also be a bit slow.

  If you use no FileVault 2 in OS X 10.7 ("Lion") or later version, you can restart as usual (not in safe mode) when the login screen appears. There is no need to log on in safe mode.

  If you use FileVault 2 in OS X 10.11 ("El Capitan") or later version, or if you don't know if use you it, you as usual then connect in safe mode, and then restart (not in safe mode.)

  If you use FileVault 2 in OS X 10.9 ("Swat") or an earlier version, or if a firmware password is defined, or if the boot volume is a software RAID, you cannot start in safe mode. In this case, request further instructions.

• Error encountered and unknown code B56 Windows update

  B56 Windows update error encountered and unknown code.

  * Title *.
  B56 Windows update error encountered and unknown code. I can't install 10 updates because of this ERROR! Someone at - it a difficulty for me or answer? I tried to install these updates for a few weeks now.

  pjrjt,
  You can watch the answer in this thread.  It covers the issue you see.

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I keep getting error 646 and 643 codes when my computer tries to update. How can this be repaired?

  My computer suddenly used to install some updates and I get an error 643 and 646 code, please help?

  Error 646 - see: http://support.microsoft.com/kb/2258121

  Error 643 - see:

  When you try to install an update for .NET Framework 1.0, 1.1, 2.0, 3.0 or 3.5, you may receive Windows Update '0 x 643' error code or error code Windows install "1603".
  http://support.Microsoft.com/kb/923100

  When installing updates using Windows update or Microsoft Update you may receive error 80070643 0 x or 0 x 643
  http://support.Microsoft.com/kb/976982

  Vista
  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Update-error-80070643

  Use the above as a guide to resolve the problem.

  This allows to check what versions are actually installed-

  The user guide for the .NET framework installation check tool
  http://blogs.msdn.com/b/astebner/archive/2008/10/13/8999004.aspx

  Order of relocation:

  1. the .net framework 3.5, then...
  2 .net framework 1.1, then...
  3 .net framework 1.1 SP1

  You can try just as appropriate repair only the versions of .NET Framework concerned.

  Downloads for the framework:
  http://msdn.Microsoft.com/en-us/netframework/aa569263.aspx

  TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.