Error 200220 CRIO 9081 and data acquisition modules

Similar Questions

• motion control for vertical actuator and data acquisition

  Hello

  I am a researcher (a branch of civil engineering) geotechnical engineering and I have very little knowledge about the acquisition of control and data motion, so would need a lot of help from the experts OR. I have only knowledge base on these 2 aspects based on my reading of some materials on the Web site of NOR and youtube videos, so I hope that you bare with me . Here are my questions:

  I am trying to build an actuator which will be used to push a probe (a penetrometer with a load cell to measure the resistance of a soil sample), resembling the concept, photography in the attached file. I need to have these criteria for my system:

  (1) actuator, which can push the probe at speeds between 0.01 mm/s - 300 mm/s with precision and move the probe cyclically (upwards and downwards) in the vertical direction
  (2) load expected on the probe into the ground range: 0.02kN - 6 kN.
  (3) necessary to get the load cell load data and the speed of the probe.

  4) able to control the actuator to a PC (speed and posotion) and monitor data from transducers and data log time even the transducers.

  Guess my beginners is that I will need:

  For orders:
  (1) software - LabVIEW and NOR-motion assistant

  (2) controller - NI PCI-7342

  (3) driver/amplifier - analogue servo AKD Drive

  (4) motor - motor brushless servo AKM

  For the acquisition:
  (1) software - based LabVIEW development systems

  (2) amplifiers or other device - no idea what type on the conditioning of signals

  (3) data acquisition device - no idea what type

  Since I'm a beginner, is - that someone might recommend components (hardware and software) for the control and data acquisition. I'm on a tight budget, so I thankful if someone could help me to recommend components good enough to build my system.

  Thanks for your help.

  At these rates, you will need to run the sensor for the cDAQ.  You can configure the analog output on the Tritex nationally on the position.  There is an adjustable filter that you can set in order to get a clean enough to 300 Hz signal.  When you learn about the Tritex, make sure that let you them know what comms and e/s that you want to use.  If I remember, not all options have worked together.  The analog output may need to be my, but you can put a resistance through the acquisition of input data to get the voltage instead.  I don't remember all the details.  You should really not too much on the Tritex/LabVIEW side.  You will send your movement parameters (beginning of end of race, speed, position, accel, cut), and if you cycle (I believe you) or simply running in a loop.  You could also just be able to use the functions of jog.  When you get close to knowing exaclty what you need, PM me and I'm sure we can work something out with the drivers.  You need only the basics.  In fact, you could probably do this all your movements via digital and analog i/o.

• delay between the trigger and data acquisition

  Hi, I use NI SMU-6368 as a tool for data acquisition. In my experience, I use an external digital trigger to start taking measures of a thermistor.

  However, before the experience, I want to know the time that elapses between the detection of the trigger signal and data acquisition start time.

  Is there a way to do this?

  Here's the kind of thing I configure to get an accurate measure of time of t = 0 trigger signal to the

  the actual first A/D conversion.   It may be too much for a measurement of the temperature, but you should get

  the right track.

  -Kevin P

  

• Card FPGA and data acquisition synchronization

  Hi, we are control and data acquisition of several hardware devices (including Photodetectors and translational stages). Until last week, we used all the controls and acquisition using a PCIe-7852R FPGA board. However, we decided to move the acquisition part to a PCIe 6363 DAQ card to improve the sharpness of the tension. During the test, I found that the internal clocks in the FPGA and the DAQ cards are slightly inconsistent (not just a phase delay, but a difference in the period).

  I know because I have generated a square wave (period = 20) using the FPGA and gains using the data acquisition card (at a rate of 200 kHz, that is, 1 taste every 5). I have observed acquired place shifts 5 every 5 seconds approximately. Such a change does not occur if the production and acquisition is done using the same Board. Therefore, the only explanation is that the data acquisition and FPGA cards clock frequencies are different. According to my calculations, the percentage difference between their time clock must be 5/5 s = 0.0001%.

  Therefore, I wonder if there is anyway to synchronize clocks between them. Or, is it possible that I can drive the FPGA clock-based DAQ hardware, or vice versa? Also, please let me know if there is something trivial as I fix.

  Thank you very much.

  Kind regards

  Varun

  Hi Varun,

  my post was only one solution...

  Your data acquisition card may take an entry to control sampling of trigger. In this mode, samples draw on a rising edge of the external clock signal. As long as you stay within the limits of the DAQ (100 MHz for your card) material sampling works perfectly. There are even examples coming with LabVIEW explaining how to program your data acquisition card...

  This mode use you your FPGA as clock source sampling for data acquisition. Both will run on the FPGA clock in sync. When the FPGA is a bit out of 40 MHz, so it won't matter because both devices are triggered on the same clock signal...

• How can I use other companion DAQmax and data acquisition in labview code?

  Hello

  I'm new in labview and want to combine four different codes of labview and run them at the same time.

  I use my data acquisition PCI-6071E and BNC-2120. I want to send an analog output (flat DC signal) to control a blower, an analog volmetre to a (DC) output pressure transducer, also receive data from a pressure sensor and hot wire probe.

  I wrote four different VI for each of them (using DAQmax to output analog and DAQ assistant for analog inputs) and each of them works well, but when I want to use them together they do not work.

  Anyone know how to make them work together?

  Thank you

  Pooya

  To the DAQ Assistant, simply follow the instructions for the selection of multiple channels when you create (where he says quite clearly,' ' or to select multiple channels "). If already created, open the DAQ Assistant and click on "Add channels" at the top of the page.

  When you use a physical channel name, you simply click on browse instead of a single channel. Use the same or for multiple channels.

• Control and simulation and data acquisition

  Hello

  I am applying to motor control in Labview. I'm sampling speed from DC engine in real time through an acquisition of data. (my sampling time is 1000 samples per second)

  Then wrap speed as input to a Simulation (simulation and design of the order) and inside the loop simulation, I have a PID controller. The PID has the actual speed of the engine for the acquisition of data and the engine reference speed as input.

  Reference engine speed comes from the generator of signals (control design and simulation-Simulation) and is a waveform.

  My step in the engine size is 1000.

  I am running this application real-time and drawing the reference signal and the motor real signals. I run into several problems with regard to the calendar.

  1. when I change the size of the step of the simulation loop, the frequency of squares of reference also seems to change. For example. What step size = 1000, duration of pulse = 1 s. What step size = 100, pulse width = 0.1. (My pulse frequency is 1 Hz, Simulation clock - 10 kHz). How step size can affect the pulse width.

  2. can you explain the relationship between the DAQ, the Simulation step size loop sampling time, Loop Simulation period.

  3. If I want to collect different sets of data using sampling different hours, it's OK to change the sampling DAQ time without changing the size of the step of the simulation.

  Would also like to emphasize that the DAQmx calendar under sample clock mode is placed in front of the simulation loop and the output is connected to the loop simulation.

  Appreciate any help.

  Hello

  Maybe some screenshots of your code would help. Furthermore, what you have read your samples together with your DAQ screws?

  (1) If you have a waveform, the output is specified as:

  

  For example, if you change the size of the step of the simulation loop, you change the simulation time which are introduced into the signal generator and affecting the waveform that you see if you do not have a size quite small step to characterize the waveform that you generate.

  (2) sampling DAQ rate is the speed at which samples are taken on the acquisition of card data itself. The size of the simulation step, help. "Specifies the interval between the time when the ODE Solver evaluates the model and updates the results of the model, in a few seconds." Simulation loop, still using, "Indicates the amount of time that elapses between two subsequent iterations of the loop of control & Simulation.". " "Step size determine the value of t that is introduced to the functions you use in the loop simulation while the loop simulation period controls simply to how fast you change the following t value. The sampling rate of DAQ hardware is a clock of completely separate hardware controlling the analogue-digital on the DAQ card converter so that you can get a deterministic dt between the samples being acquired.

  (3) you can change the schedule for the acquisition of data, but you will need to restart each time the changes take effect. If you change the calendar of data acquisition and want your values to correlate with your simulation, you will need to change your size of step as well.

  -Zach

  -Zach

• Executable files and data acquisition Drivers

  It is an interesting question that I hope someone can help me with.

  My client has little code I need support.  They have a card PCI-1200
  card.
  My understanding is the latest driver that works with this card is
  Traditional DAQ 6.9.3.

  They have 6.9.3f3

  Then I made the mistake of upgrading their code of 7.1 to 8.5.  The code
  works
  on my machine.  When I create an executable file, the executable works on my
  machine;
  However, when I try to run the executable file on their computer software
  housing starts
  and then stops.  I get no error.  The executable file only
  don't
  run.

  I wonder what I should create an executable with the driver
  Version
  6.9.3 on my development machine?

  Thank you

  Dan

  I solved the problem!

  I downloaded the 8.5.1 engine LENGTH of Web site of NOR and installed on my target machine.  It worked!

  Previously, I copied the execution engine of my Cache on my development computer folder.

• Assistants of programming and data acquisition

  Using the flat sequence and DAQ Assistant, how can implement us planning algorithm to enable or disable a specific image in the sequence?

  Do not use the flat sequence structure! You can't turn any image. Just one of the disadvantages of the structure of the sequence. They are rarely necessary. Flexibility, use a state machine.

• Input module of data acquisition can be read by two or more LabVIEW vi at the same time % 3F

  I use the DAQ palette in LabVIEW to read the virtual channels of the input data acquisition module. I've done several VI who read many entries of three modules of simulations. The problem appears when I run two or more VI´s reading entries from the same virtual module (for example. first.VI module 1 input ai0 and second.VI bed ai0 entry module 1 bed), when this happens the next errors are shown:

  Error-50103

  Platform AND Services: The specified resource is reserved. The operation could not be performed as indicated.

  and

  Error-200022

  Resource requested by this task has already been reserved by another task.

  It's worrying because I want to get the DAQ chassis and some modules, but if this problem is present with physical equipment my application may be unnecessary. This means that entry module only can be read once at the time?

  I m using global variables in each Subvi to share data with main VI, however, I found the solution in a different way... I just changed to single channel and dbl sample playback mode, so I Don t need to clean up the task of reading in my subVI´s, the zeros isn´t problem here, and the six subVI´s work at the same time!

  Thanks for the tips!

• Sampling frequency and Nyquist theorem - data acquisition

  Hi all

  I have a rectangular steel beam that is affected with a weight of 100 kg and I would look for the modules able to sample the signal correctly.

  The Nyquist theorem says that if half of the sampling frequency is higher than the input signal, it will be recorded correctly.

  What I think about it before you buy a data acquisition module to find the signal of the rectangular steel beam? I will perform an analysis model by finite elements using the elastic properties or properties of plastic? Is the natural frequency of the associated structure of the input signal?

  Thank you

  Husband

  Some technical assistance is appropriate, determine that the higher frequency component is interesting to your signal. Set your frequency of sampling to twice this value. In addition, to protect data, to build a filter of antisliasing of material it alleviates any energy above the highest frequency of interest.

  Mike...

• The reading of data acquisition via tcp

  Hello

  I am building an application that controls an acquisition of data via tcp.

  I have a JAVA program that communicate with labview, give a command and data acquisition starts. (So, I read the correct Java data at Labview)

  My problem is if I try to read data acquired by data acquisition (continuous sample 1 k samples), I've read strange values.

  I transform of double values in the string and send it via tcp.

  How can I read it in Java? What type of socket should I use? What is a rate problem?
  I also tried to transform small/big-endian byte order, but it does not work.

  I enclose a sketch of this part of the application.

  Please help me, I try for 2 weeks!
  Thank you all...

  I find the solution in the lavag forum.
  I post here, if it can help someone.

  http://lavag.org/topic/16359-sending-LabVIEW-data-via-TCP/page__pid__99983#entry99983

• water data acquisition motor control

  dose anyone know how Precisele engine in labview using DAQ? Please tell me how I can do?

  Concerning

  Saeed

  OK, I'm him giving the alternative energy source and just to control data acquisition rather then powered data acquisition, shell, I use the driver of transducer between the acquisition of data and engine or any other switch. Yes I m interested just in power of the engine after obtaining the indication of my sensor. Please tell me what I can use between the engine and data acquisition.

  Kind regards

  Saeed

• LabVIEW statechart module of data acquisition error external trigger

  I have a 2 loop vi is the acquisition of data of a data acquisition instrument loop and the second is a loop to run my statechart of.  I would like to respond to an error in device of acquisition data if it occurs in transition out of my current state in my diagram States-transitions and enable management of custom unique business mistakes.  My States-transitions diagram is synchronous and send it external trigger.vi funciton will not work with it.  How to achieve this?  In addition, there is some confusion about this literature in http://zone.ni.com/reference/en-XX/help/372103F-01/lvscconcepts/sc_c_callervi/ at the bottom of the page it saidNote sending triggers for synchronous charts is optional. If you do send triggers, LabVIEW sends the NULL trigger for transitions. If you send a synchronous statechart triggers, you can send these triggers to the caller VI. »

  Is it possible to do this and if so how with the synchronous statechart?

  Thank you, it should work for me

• Serial numbers for the cRIO-9081 Module

  Is there a way for the FPGA in the cRIO-9081 to read the serial number, date of calibration of the NOR-9201 module installed in the cRIO?

  I want to get this information and send it to my Host.vi, because we have a duty to provide information instrument document during a series of tests.

  Thank you

  Paul

  

  Use a property node of the module to read the number of series/VendorId... but the calibration date is not stored. (FPGA code example shows NI9205 data)

  Here a Fifo of DMA target host is used to send the data to the controller of the CR...

• DAQmx data acquisition with persistent error of nyquist

  Hi, I created a multi channel data acquisition vi (accelerometer 2 and 1 sound pressure) using models for producer.   The vi is attached. Thanks to labview 2011.  I get the error of nyquist (2 enclosed) when you make a bandpass filter between 50 to 5000Hz.  This happens despite having put my sampling rate to 22050Hz.  When I checked the output of wave I noticed that the signal has a dt 1 s.  The text output to check the result.  I could not understand how this is so since I had set the sample rate to 22 k Hz.  Any help will be much appreciated.  Thank you.

  I would do something like that.  You must calculate the dt of the set (with the recipricol) sampling frequency and use to initialize the shift registers.  This way you only need to change 1 constant if you need to change your sample rate.