Error installing first Cisco optical 9.6

Similar Questions

• First Cisco 3.0 crashed after installing pi_technology_package - 3.0.2 - 1.0.56

  Hello

  Our first Cisco 3.0 after installing pi_technology_package - 3.0.2 - 1.0.56 crashed. SSH is available but not Web.

  Here is the story:

  1-. OVA installed

  2-. Installed the following hotfixes:

  Feature-Pack-3 - PI3.0 - 25.ubf

  4-Pack-device - PI3.0 - 15.ubf

  pi302 - 16.ubf

  pi303 - 10.ubf

  Server rebooted and everything seems to work fine.

  3-. Installed pi_technology_package - 3.0.2 - 1.0.56, rebooted and web server doesn't work anymore.

  We tried to restore a previous backup, perform a reset of db ncs and restart the ESXi machine, but without success.

  genpro01 / ncs status admin #.
  Health Monitor runs with an error. (Primary [role] [State] not configured HA)
  initHealthMonitor(): cannot start DB
  Database server is stopped
  FTP server is running
  TFTP Server is running
  MATLAB Server is running
  MATLAB Server Instance 1 is running
  MATLAB Server Instance 2 is running
  NMS server is stopped.
  Gateway of CNS with port 11011 is down
  CNS with port 11012 SSL gateway is down
  Gateway of CNS with 11013 port is down
  CNS with port 11014 SSL gateway is down
  Plug-and-Play bridge with port 61617 broker is down
  Plug n Play bridge config, image and resources are declining over https
  Plug-and-Play gateway is stopped.
  SAM Daemon is stopped.
  DA Daemon is stopped.
  genpro01 / admin #.

  Any suggestions?

  Kind regards

  David

  David,

  Unfortunately things can get really watered (technical term) with the database if the application (ncs) server is not restarted after each pack of patch installation or device. Later versions of patch began by pointing out that right from the start.

  I would say that you have two options-

  1 rebuild from scratch and just re - import devices. It is a self-service option.

  2 open a TAC case and see if they can recover the current state. The reports I got colleagues and read elsewhere here is the recovery of a failed installation of this tech pack was difficult at best.

  Sorry to be the bearer of bad news.

• When I install first elements 13 I get the error message: DS003 what kan I do?

  When I install first elements 13 I get the error message: DS003 what kan I do?

  Please see the links below.

  • Errors ' Exit Code: 6, "" Exit Code: 7 "|"» CC, CS6, CS5.5
  • Adobe CS6: Exit Code: 7

  Hope this will help you.

  Kind regards

  Hervé Khare

• Just installed first Pro CS5, impossible to perform, error code: 1

  Hello. Just installed first Pro CS5 for the first time, but can't run it. I get the following error code:

  Uninstall and reinstall the product.

  If the problem persists, contact Adobe Technical Support for assistance in specifying the error code that appears at the bottom of this screen.

  Error: 1.

  http://www.Adobe.com/FR/support

  ()http://puu.sh/2jN4T/6164d5b656( )

  With the help of Windows 8.

  Thank you for any input!

  Dryaan if you're still having trouble with your setting file permissions, so I recommend to communicate directly with our support team.  For the best support, I recommend our chat support at http://adobe.ly/yxj0t6.  Our chat representatives can provide a personalized experience to solve the problem you described.

• LEGO Mindstorms 2.0 crashes at startup when LabView Signal Express is installed first

  When NI Circuit Design Suite education edition is first installed in a computer and the LEGO Mindstorms software second, the LEGO Mindstorms software does not work, he reported the following:

  Error: A required file is broken

  Possible solutions: reinstall the driver of LEGO Mindstorms NXT (tried but does not work)

  Error code: 1003

  Ordinal not found

  The 18 ordinal not found in the library of dynamic links NIVISV32.dll

  Error loading "fantom.dll".

  The operating system cannot run %1

  On other computers the LEGO software starts, it displays the part of the initial screen and then a small window will open saying that the Mindstorms software has made an error and that it will close. The previous report does not display.

  If LabView Signal Express is uninstalled and reinstalled the software, LEGO, the LEGO software works.

  I downloaded and installed the new and old of the NIVISV32.dll versions and is not correct the problem. I went as far as version 4.20 of the dll because it is dated in 2007 and dll files installed by the LEGO software when it works is also dated 2007, but if I install the dll without uninstalling LabView Signal Express, the continuous LEGO software does not.

  Please advice how to fix this without having to uninstall first LabView Signal Express. If the LEGO software is installed first, LabView Signal Express will use and no not to replace the old version of the dll 2007 installed by the LEGO software? Y at - it an update of the LEGO software that corrects this problem?

  I repeat: I know a solution is to uninstall LabView Signal Express, install LEGO Mindstorms and then reinstall LabView Signal Express but I have 60 computers already cloned and deployed with this problem, so I don't want to go to this long process to solve the problem. Computers use Windows 7 and the problems occur on both 32 and 64-bit versions of Windows 7.

  Any ideas?

  
  

• The limit of the device must be less than or equal to the limit of life cycle license in first cisco 2.2

  Hi all

  I have seen under error in the tool main 2.2 Cisco infrastructure

  The limit of the device must be less or equal to the limit of license of life cycle and also secondary device ISE inaccessible since premium.

  Could you please suggest how we can solve your problem.

  Thanks in advance...

  Kind regards

  Sachin

  Yes. Life cycle license are by smart device managed. See this page for a good overview:

  http://www.Cisco.com/c/en/us/support/docs/cloud-systems-management/Prime...

  .. as well as this page:

  http://www.Cisco.com/c/en/us/products/collateral/cloud-systems-Managemen...

  .. who States:

  Life cycle license: allows access to all the features of the life cycle, which includes the configuration of the devices, image management software, basic health and performance monitoring, fault management, troubleshooting and customer visibility on the network. The license of the life cycle is based on the number of managed devices. Life cycle of the licenses are available in sizes from package of 25, 50, 100, 500, 1000, 2500, 5000, 10,000 and 15 000 devices and can be combined as needed to reach a total number of device under license.

  A device is uniquely identified through the assigned IP address and system object ID (SysOid). Routers, switches, light/unified access points and network first Cisco (NAMs) analysis Modules are charged on the number of licenses. If a switch stack is managed via a single IP address, it counts as a single device. A single frame will, however, be counted as multiple devices if the chassis is configured with several IP addresses. For example, a switch with several service cards, such as a firewall and so forth, or a stackable switch with an IP address assigned to each switch who is involved in the stack is considered multiple devices within the first Cisco Infrastructure. Cisco Wireless LAN controllers (WLCs), autonomous and peripheral access points third are not counted against the number of licenses.

  When you have more devices that licenses, you will receive the error see you and prevented from adding additional devices to your inventory.

  We see it more often when it is light (i.e. not independent) APs are added to a wireless controller. PI will not prevent the new APs to be added, they are managed under their association with the WLC. However, if you try to add a new switch it would prevent you to do until the deficit of licenses has been sent.

• Error 500 CTS Cisco ' remote site is not supported contact your technical support.

  Hi guys, I installed 2 Cisco 500 CTS with Cisco CM 7.1.3

  I've updated the CTS 500 version 1.6.7 and I could add to the Director and I have followed all the configuration mentioned in Configuration Cisco Telepresence with Call Manager.

  I also configured the Midlet services and everything seems to work very well.

  The problem is when I'm doing a call between the 2,500 CTS, I'm getting on the screen the below error:

  "Remote site is not supported contact your technical support.

  Knowing that the two CTS have the same version and two of them are registered correctly and no problem is show.

  Can someone help me how I can check where I get this error?

  Thank you

  Seems to be a problem of config CUCM

  Check box and the location make sure you allow enough for a video telepresence call P.C.

• Impossible to install the Cisco VPN Client on Windows 7

  Hello

  After an uninstall successful VPN Cisco version 4. I try to install the Cisco VPN Client 5.0.07.0290 version.

  But after the launch of vpnclient_setup.msi, the wizard starts. When I click on the next button, I get the following message: "installation ended prematurely because of an error".

  As an attachment, I add the details of the discovery of the error in the logs of windows (logError.txt) and the logs generated by the MSI installer in verbose (log2.txt) mode.

  My computer is a lenovo W500 with Windows 7 64-bit and 4 GB of memory (compatible with the requirements of the Cisco VPN Client).

  I have administrative privileges on this computer.

  Please help me!

  I need to use it to connect to my corporate network.

  Thanks in advance.

  BR

  Jerome

  If you want to try another software, I know that works I used it up until cisco came out with a 64-bit client there. Is the 64-bit version of shrew 2.1.0 it worked very well, you will just need your file FCP of cisco for import into if you have. This will tell you if the client or your system at least.

• My current osx is the version 10.5.8.  I read the posts on this site advises users to buy 10.6 and then upgrade more far away. Since I was only 1 GB of memory, do I need additional memory installed first? Is this possible? Thanks for any help!

  I explore what I need to do to upgrade my imac. My current OS is x version 10.5.8.  I read the posts on this site advises users to buy 10.6 (Snow leopard) and then upgrade more far away. Since I was only 1 GB of memory, do I need additional memory installed first? Is this possible?  I have an Intel Core 2 Duo 2 GHz processor and 1 GB of memory. My Info says memory I have 1 Bank empty. Thanks for any help!

  You need to install more RAM before moving to Snow Leopard and need to do before moving to Lion or newer. Buy it from a source OWC or Crucial.

  (138456)

• How to move the original system to the SSD newly installed without an optical drive?

  I want to buy a W530 and spare SSD upgrade.

  I want to order one without a DVD player.

  How to move the system of origin, drivers and other software for the SSD newly installed without an optical drive?

  Hope someone could help me. Thank you.

  The two utilities that I mentioned manage alignment automatically. Also, I photographed my hard drive, then restored the SSD. I have no clone, which means a direct copy of the HDD to the SSD.

  I just went through this myself in July, using Acronis True Image 2012 to get my existing on my 256 GB SSD mSATA HARD disk image. It worked like a charm. I checked that the SSD has been properly aligned.

  See:

  Migrate to SSD

  and:

  Check the alignment of SSD

  Now stop worrying!

• Can't reinstall incredimail getting the error, install has insufficient prfivileges to edit the file

  "I get an error 'Install a sufficient privileges to modify the file'. code 1321. How can I reinstall with the code. How should I do?

  The error message indicates what file it has problems with?

  Click with the right button on the installer and choose Run as administrator.

• LaserJet P1102: HP LaserJet P1102 - error "INSTALL BLACK CARTRIDGE"

  Tried to print a provision of the EAGLE Cadsoft program card on photographic paper, A6. The paper A6 was on top of the A4 papers, if the printer did not take the A6 paper. After that, the error "Install black cartridge" appeared. Tried to power off AND removed the power cord for 1 minute, checked for paper inside, cleaned the pins on the cartridge of the printer... still the same error. Help will be greatly appreciated.

  Thanks for providing this information @north991.

  I would like to do a hard reset to see if that will solve the problem.
  Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
  Reconnect the power cable to the output of the printer and the wall, and not a surge protector.
  This ensures that the printer is full on and can help this situation.

  Please try the steps listed in this document for the Solution for light flashing light and pay Attention, Pro printers HP LaserJet - flashing lights.

  If the problem persists, please Contact the HP Support and let them know that you have a warranty on toner and inquire about a replacement. Check the model number and the form to receive a file number for faster assistance.

  Please hold me. Thank you.

• my computer will not install itunes 10.5, it tells me "Setup has encountered an unexpected error installing this package. This may indicate a problem with this package. The error code is 2330.

  original title: Itunes problem

  my computer will not install itunes 10.5, it tells me "Setup has encountered an unexpected error installing this package. This may indicate a problem with this package. The error code is 2330. "What should I do?

  Contact the manufacturer (Apple) of the application (iTunes) you are having problems with.

  Uninstall all previous versions, try to download (re-record not running) and then do a right click on it and RUN AS ADMINISTRATOR.

  (Vista 32-bit or 64-bit)?

• Epson Aculaser C 1100 printer does not print after that the text of the error 'install C Tnr basket' black and printer doenst photography black and white or grayscale pages

  Epson Aculaser C 1100 printer does not print after that the text of the error 'install C Tnr basket' black and printer doenst photography black and white or grayscale pages

  the printer is not the shades of grey even print cartridge is not yet empty

  y at - it software for hauler color printing?

  Thanks for your comments

  Hello Nilsvolkel,

  Thanks for the reply.

  I'm sorry for the late reply.

  I appreciate your patience and time.

  Do not require any special software.

  However, you can use the steps in the following articles and check.
  Reference:
  http://eSupport.Epson-Europe.com/ViewArticle.aspx?LNG=fi-fi&kbid=328037&data=FCFfEfoyEiGLYDIUqzWyE0QE3127X87y&CL=1

  http://Windows.Microsoft.com/en-us/Windows/choosing-print-options#1TC=Windows-7

  Please keep us informed.

  Thank you

• Error installing 3rd party certificate to 5508 (version: 8.0.133)

  Hello

  I want to install the certificate 3rd party controller file.

  The same file final-cert (final.pem) work on WISN (version: 7.0.240).)

  But error install 5508 8.0.133 execution!

  09 ying_mu_kuai_zhao_2016 - 27_shang_wu_12.43.39.png

  

  What could I do to fix the problem?

  Thanks for your help.

  I had a similar problem with a 5508 on 8.0.110.0 and finished by adding the public key of the intermediate CA that it was signed with the pem file (available from the supplier you bought at). This allowed for installation and came as confidence in the browser.

  See you soon,.

  Ric