Impossible to install the Cisco VPN Client on Windows 7

Similar Questions

• How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Dear all

  How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Concerning

  Hi Imran,

  Can't do much about that because it depends on what authenticate you the VPN server and how the settings. But let me introduce you to the memory layout. Once you install and open a VPN client. Press it again and it opens up a new page for the VPN config.

  Example of configuration as it is attached. But it differs depending on the configuration of your vpn server.

  Once you create and save this profile. Your FCP file is stored.

  Please assess whether the information provided is useful.

  By

  Knockaert

• Unable to connect via the Cisco VPN Client

  Hello

  I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

  I am not able to connect and watch the journal on the SAA

  ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

  ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

  ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

  What could be the reason.

  Concerning

  Hi, I had this same problem, here is the solution:

  When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

  Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

  Well, change your strategy using MD5 isakmp / OF would do the trick.

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• Unable to connect using the Cisco VPN client

  Hi all. I recently configured a 5510 ASA to allow remote access using the Cisco VPN client. The problem is that everything works fine when I connect using a modem classic or on a computer with a public address that I use for testing purposes, but whenever I try to connect with on an ADSL line, I can't access to the resources. I have connection and after that nothing, I can not achieve anything.

  I enclose the relevant configuration information in the attachment. Any help is welcome.

  Depending on the version, add...

  ISAKMP nat-traversal

  or

  ISAKMP nat-traversal crypto

  Should be all you need.

• What are the ports used by the Cisco VPN Client?

  Hello

  I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

  I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

  What are the ports used by the Cisco VPN Client?

  Thank you

  You need to open:

  UDP 500

  ESP protocol

  You must also open the UDP 4500 port (if using NAT - T).

  In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

  1. If using IPSec over TCP 10000, then open TCP 10000.

  2. If using IPSec over UDP 10000, open UDP 1000.

• How to allow access to a local area network behind the cisco vpn client

  Hi, my question is about how to allow access to a local area network behind the cisco vpn client

  With the help of:

  • Cisco 5500 Series Adaptive Security Appliance (ASA) that is running version 8.2 software
  • Cisco VPN Client version 5.0 software

  Cisco VPN client allows to inject a local routes in the routing table Cisco ASA?

  Thank you.

  Hi Vladimir,.

  Unfortunately this is not a supported feature if you connect through the VPN Client. With VPN Client, that the VPN Client can access the VPN Client LAN host/local machine, not host from the local network to business as customer VPN is not designed for access from the local company network, but to the local corporate network.

  If you want to access from your local business to your LAN network, you need to configure LAN-to-LAN tunnel.

• multi-site VPN with just the cisco vpn client

  Hello everyone

  Please I need your help.

  We have a headquarters office and up to 60 is BranchOffice, we want to create VPN network between its. so let's deploy 2 router cisco esy vpn server with HA (HSRP) at the Headquarters Office and all branches have Connection ADSL and they will use just the cisco vpn client to connect to the Headquarters Office.

  My question is: is it possible to do it just with the client vpn cisco without purchased for any exercise bracnh a cisco router to create an ipsec tunnel because it is so expensive?

  It depends on if the routers to offices can handle NAT with several internal VPN clients to 1 IP address. Most of the new material should be fine. Keep in mind the maximum limit of the VPN client, with 60 agencies and 5 people each of whom you are above the limit.

  Michael

  Please note all useful posts

• Cisco VPN Client and Windows XP VPN Client IPSec to ASA

  I configured ASA for IPSec VPN via Cisco VPN Client and XP VPN client communications. I can connect successfully with Cisco VPN Client, but I get an error when connecting with the XP client. Debugging said "misconfigured groups and transport/tunneling mode" I know, they use different methods of transport and tunneling, and I think that I have configured both. Take a look at the config.

  PS a funny thing - when I connect with client VPN in Windows Server 2003, I have no error. The only difference is that client XP is behind an ADSL router and client server is directly connected to the Internet on one of its public IP of interfaces. NAT in the case of XP can cause problems?

  Config is:

  !

  interface GigabitEthernet0/2.30

  Description remote access

  VLAN 30

  nameif remote access

  security-level 0

  IP 85.*. *. 1 255.255.255.0

  !

  access-list 110 scope ip allow a whole

  NAT list extended access permit tcp any host 10.254.17.10 eq ssh

  NAT list extended access permit tcp any host 10.254.17.26 eq ssh

  access-list extended ip allowed any one sheep

  access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh

  sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0

  tunnel of splitting allowed access list standard 192.168.121.0 255.255.255.0

  flow-export destination inside-Bct 192.168.1.27 9996

  IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0

  ARP timeout 14400

  global (outside-Baku) 1 interface

  global (outside-Ganja) interface 2

  NAT (inside-Bct) 0 access-list sheep-vpn

  NAT (inside-Bct) 1 access list nat

  NAT (inside-Bct) 2-nat-ganja access list

  Access-group rdp on interface outside-Ganja

  !

  Access remote 0.0.0.0 0.0.0.0 85.*. *. 1 2

  Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1

  Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1

  Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1

  Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1

  Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1

  Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1

  Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1

  Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1

  dynamic-access-policy-registration DfltAccessPolicy

  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

  Crypto ipsec transform-set newset aes - esp esp-md5-hmac

  Crypto ipsec transform-set esp-3des esp-md5-hmac vpnclienttrans

  Crypto ipsec transform-set vpnclienttrans transport mode

  Crypto ipsec transform-set esp-3des esp-md5-hmac raccess

  life crypto ipsec security association seconds 214748364

  Crypto ipsec kilobytes of life security-association 214748364

  raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

  vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1

  card crypto interface for remote access vpnclientmap

  crypto isakmp identity address

  ISAKMP crypto enable vpntest

  ISAKMP crypto enable outside-Baku

  ISAKMP crypto enable outside-Ganja

  crypto ISAKMP enable remote access

  ISAKMP crypto enable Interior-Bct

  crypto ISAKMP policy 30

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  No encryption isakmp nat-traversal

  No vpn-addr-assign aaa

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.192 outside Baku

  SSH 10.254.17.26 255.255.255.255 outside Baku

  SSH 10.254.17.18 255.255.255.255 outside Baku

  SSH 10.254.17.10 255.255.255.255 outside Baku

  SSH 10.254.17.26 255.255.255.255 outside-Ganja

  SSH 10.254.17.18 255.255.255.255 outside-Ganja

  SSH 10.254.17.10 255.255.255.255 outside-Ganja

  SSH 192.168.1.0 255.255.255.192 Interior-Bct

  internal vpn group policy

  attributes of vpn group policy

  value of DNS-server 192.168.1.3

  Protocol-tunnel-VPN IPSec l2tp ipsec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split tunnel

  BCT.AZ value by default-field

  attributes global-tunnel-group DefaultRAGroup

  raccess address pool

  Group-RADIUS authentication server

  Group Policy - by default-vpn

  IPSec-attributes tunnel-group DefaultRAGroup

  pre-shared-key *.

  Hello

  For the Cisco VPN client, you would need a tunnel-group name configured on the ASA with a pre-shared key.

  Please see configuration below:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  or

  http://tinyurl.com/5t67hd

  Please see the section of tunnel-group config of the SAA.

  There is a tunnel-group called "rtptacvpn" and a pre-shared key associated with it. This group name is used by the VPN Client Group name.

  So, you would need a specific tunnel-group name configured with a pre-shared key and use it on the Cisco VPN Client.

  Secondly, because you are behind a router ADSL, I'm sure that's configured for NAT. can you please activate NAT - T on your ASA.

  "crypto isakmp nat-traversal.

  Thirdly, change the transformation of the value

  raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

  Let me know the result.

  Thank you

  Gilbert

• Using Cisco VPN Client in Windows 7 Professional 64 bit

  Hi all!
  I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem

  Open the XP VM itself, do not use the shortcut that was published in
  the W7 boot menu. You need to install Outlook / your email client
  Inside the virtual machine, as well as on the side of W7. You can point to the same
  PST files if you have local PST files, but you just can't open them in
  at the same time of W7 and XP VM.

  There is no way to bridge using the shortcut of publishing app

  Some people have reported success with the third party IPSec
  replacements as customer universal shrew or the NCP. Your IT Department.
  would like to know if these are supported

  :

  > Hello all! I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem
  Barb Bowman www.digitalmediaphile.com

• Cisco VPN Client with Windows 7 Home Premium 64-bit

  I recently bought a new laptop with Windows 7 Home Premium 64-bit.   I need to connect to a VPN IPSEC to work.  I tried the current VPN client and after reading the posts in this group, I tried vpnclient-win-msi-5.0.07.0240-k9-BETA.exe.  When I tried to install the beta version, I get the following error message:

  Error 28011: Windows 64-bit is not supported by Cisco Systems VPN Client 5.0.07.0240.

  Any suggestion would be appreciated.

  Hello

  You should download the 64-bit version. vpnclient-winx64-MSI-5.0.07.0240-K9-Beta.exe is the version you tried to install the 32-bit version

  Thank you

  John

• Cisco VPN Client for Windows 7 and WWAN devices

  Hello

  Does anyone know when Cisco will release a VPN Client for Windows 7 update that supports devices WWAN using NDIS 6.2?

  Thank you

  Dave,

  End of the client VPN of life was announced. In my view, it is safe to say that no new features will be introduced.

  AnyConnect is the way to go (Alternatively Windows 7's native IKEv2 connection works in IOS).

  Marcin

• NetMeeting does not not between the cisco vpn clients

  Hello

  I had posted the same query a weeks but did not get any reply.just adding more details and hoping som1 help me.

  Here's the real problem:

  We have a client that users use clients vpn cisco to connect LAN business from the public network and access as expected and also able to run netmeeting from his pc, but when users attempt to run netmeeting between two connected to the public network, vpn clients with same ip pool, it does not work.

  Thank you & best regards

  Madhu.

  Try to delete "nat (outside) 1 192.168.1.0 255.255.255.0" and try again.

  Or try adding something like this...

  outside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.0 255.255.255.0

  NAT (outside) 0-list of access outside_nat0

• Configure the Cisco VPN client to pass through the VPN site-to-site (GUI)

  Hello

  I say hat the chain and responses I've seen to achieve this goal have been great...

  https://supportforums.Cisco.com/discussion/12234631/Cisco-ASA-5505-VPN-p...

  and

  https://supportforums.Cisco.com/document/12191196/AnyConnect-client-site...

  My question is "we will get this configuration by using the graphical user interface for someone who is not notified about the command line?"

  Thank you

  Of course, all this can be configured via ASDM.

  Looking at the second example you posted above, they point you first change:

  ACL split of the tunnel for the AnyConnect customer

  This Configuration > remote access VPN > network (Client) access > AnyConnect connection profile > (chose the profile and select Edit) > (choose "Manage" next to group policy) > Edit > advanced > Split Tunneling > ensure that the policy does not "Inherit" but rather "Tunnel network list below" > Unselect "Inherit" next to the network list, then 'manage '. Enter your networks you want in the GUI in this dialog box. Click OK all the way back to the main window ASDM and click on apply.

  You then change:

  Crypto ACL for the tunnel from Site to Site

  To do this, go to Configuration > VPN Site-to_site > connection profiles > (choose your profile and select edit) > add the VPN client address pool to the list of local network between protect networks. Yet once, click OK all the way back to the main window ASDM and click on apply.

  Then, allow the

  ASA to redirect back on the same interface traffic it receives

  .. is defined under Configuration > Device Setup > Interfaces. (check the box at the bottom of this screen). Click on apply

  Finally, there is the NAT exemption. For which go to Configuration > firewall > rules NAT. Add a NAT device rule before rules network object with Interface Source out, Source address your address pool VPN, the Destination address to include remote subnets and Action is Static Source NAT type source address and destination address remaining as original (i.e. without NAT). Once on OK all the way back to the main window ASDM and click on apply. Save and test.

  Good luck. Don't forget to note the brand and posts useful when your question is answered.

• How to save the password to the Cisco VPN Client?

  Hello

  I use version 4.8 to connect to the VPN from my client, I would like to save my password so that I don't have to enter it each time.

  I've amended the FCP file to include:

  ! SaveUserPassword = 1

  and my password in UserPassword =, but it worked only once, after I restart it no longer works.

  Then I see the method to use the command-line vpnclient.exe to connect and provide the password as a parameter to the command:

  vpnclient connect user pwd

  But I got this error when you try to connect:

  Setting user password failed. User password is read-only.

  And the client always requests the password.

  Any ideas?

  Thank you

  The server sets the password save, you will not be able save locally unlessit is enabled on the server side. If the customer has an ASA, follows allows him under the group policy for VPN clients.

  allow password-storage