error message sirenacm.dll happens to the computer starts and says to reinstall; How do I do that?

Similar Questions

• Start error message "Run DLL there was a problem starting C:\users\Maureen\AppData\Local\Temp\ the specified module could not be found."

  Original title: run DLL error message

  When I start my computer, this error message box appears: run a DLL there was a problem starting C:\users\Maureen\AppData\Local\Temp\ the specified module could not be found.  I tried to run malware byte scan Antivirus scans, security analysis of microsoft, microsoft's malicious software removal tool, scan, prevx, and nothing was found.  I'm not very well informed about computers, but this error box is annoying and I would like to quit smoking.  Thanks for your help.

  Hello MaureenCYB,

  Thank you for the question!

  I'm sorry to know that have problems you with the startup message. As I understand it, you get an error message "Run DLL there was a problem starting C:\users\Maureen\AppData\Local\Temp\ the specified module could not be found" when starting.

  I need to ask you a question to help you best.

  Were there any changes (hardware or software) to the computer before the show?

  To help resolve the error and other messages, you can start Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Note: follow step 3 to reset the computer to start as usual after the boot process.

  Answer to us if you are having problems with error starting or any other issue of Windows, and I'd be happy to help you again and try to correct the problem as soon as possible.

  Good day!

  Hope this information helps.

• I'm trying to install Office note 8.1 but get this error message immediately after you enter the serial number and authentication code.

  Remark Office OMR

  I've been remark office omr 8.1 installed on 32-bit windows vista (intel pentium DC) for the last year laptop. Now plan to move it to a more recent hardware and the OS.

  I'm trying to install Office note 8.1 on Windows 7 Home Basic 64 bit (on laptop AMD E450 DC base). But am getting this error message immediately after you enter the serial number and authentication code. I tried to install different versions of the .net Framework (from 1.1 to 4), but nothing seems to solve the problem.

  I even tried to install it in mode compatibality. but no luck.

  Here is the error message (between BEGIN and END lines)

  -BEGIN-

  An error occurred instantiating the object of authentication. Please restart your computer, and they run the Setup again.
  Error number = 2147219705

  Error = description

  ------ END--------

  Appreciate any help

  Thank you

  SJ

  Just for the follow-up of this: I have sent comments, and they responded in 20 minutes with:

  Please contact the Support of the note.  I'm sorry that you are experiencing this error, but it seems by the error message that you install note on a Windows 7 computer.  This error is caused by a Microsoft security update that was released in July 2011 for Windows 7 and caused upward to change our software.  Here is access to our Download Center for you to install the version 8.4 of note.  You will use your current serial number, license key and authentication code.
  They then provided a link to their Download Center where I could download 8.4
  E - mailer to * address email is removed from the privacy * and they will answer you. They have great customer service.

• Samsung TS-H653G DVD burner, I have this unit in my Dell Inspiron but D drive disappeared from the computer screen and will not reinstall successfully.

  I have this unit in my Dell Inspiron but D drive disappeared from the computer screen and will not reinstall successfully. Possible solutions please

  I have this unit in my Dell Inspiron but D drive disappeared from the computer screen and will not reinstall successfully. Possible solutions please

  Hello

  See how you go with this great piece of software.

  http://www.thewindowsclub.com/repair-fix-Windows-7-Vista-problems-with-FixWin-utility

  Concerning

  GT4U

• SE error message: "Run"DLL"there is a problem starting. C:\Users/John\AppData\Local\Conduit\BackgroundContainer\BackgroundContainer.dll

  Get the below error message every time I start my computer:

  Run DLLS
  There was a problem starting
  C:\users\John\AppData\Local\Conduit\BackgroundContainer\BackgroundContainer.dll
  The specified module could not be found.

  Hello cuefox, thank you very much to judge me.
  We're here to help.
  Continue to browse the web with Firefox, thanks once more.

• Error message WLMON or WLMON.exe, the missing files and WPC54G

  Portable running Linksys Network adapter card WPC54G

  OS: XP

  Driver version: 4.100.27

  I get an error message that WLMON.exe has no inialize, and a second pop up that tells me that there are missing files. Can someone tell me if there is a fix to this addition WLMON out of my boot ini and the devil made WLMON.exe? Did he get the same problem and have a solution?

  Do not install the Linksys monitor... just install the driver.

  Remove the Linksys adapter and uninstall the Linksys software menu programs... Re - install drivers insert the CD of Linksys install in your CD-ROM drive, when the welcome is displayed click on exit, connect your USB adapter now... When the Hardware Update Wizard window appears, click on install the software automatically (recommended) and then click Next... Click Finish when the installation is complete.

  Click Start and open the control panel and double-click on network connections. Right click on wireless network connection, and then select view available wireless networks "-If you see your network wireless in the list, the highlight by clicking 'single' on it now, click on the 'Connect' button below-if your wireless network is secured, it asks you to provide the network key - provide the wireless network key and confirm again in the confirmation box and click 'Connect'." It should work...

• Error message: "unable to connect to the RPC Server" and no internet connection.

  Original title: recently installed a program of pc cleaner. Seemed to really speed up my laptop that is running Windows XP.

  After two days I try to connect to the internet and no connection lie. Uninstalled the pc cleaner without problem but the problem continues to exist. All tests, etc., result in "unable to connect to the RPC server. Slide short drive and reinstall XP, are there any other things to try?

  Hi Wantamustang,

  You can try the following steps and check.

  You can set the remote procedure (RPC) call Service to start automatically:

  a. clickStart, point to settings, clickControl Paneland then double-clickServices.

  b. in theservices list, click the remote procedure (RPC) call Serviceand then clickStartup.

  c. underStartup Type, click Automaticand then click OK.

  d. restart your computer.

  You can also consult the following article:

  Windows wireless and wired network connection problems

• Receive the error message"Windows Media Player is not installed correctly and must be reinstalled. "

  * Original title: Windows Media Player

  I recently updated my Windows 7 and now my Windows Media Player will not work.  The following message appears: Windows Media Player is not installed correctly and must be reinstalled.

  I don't see where I can download the Windows Media Player for Windows 7.  Any help would be appreciated.

  If you have a ' normal/standard' Windows 7 version, then see if it deletes, reboot, reinstall, reboot the help method - http://www.howtogeek.com/howto/26107/how-to-reinstall-windows-media-player-in-windows-7-to-solve-problems/

  If you have the "n" or "KN" W7 version, you may need this - http://www.microsoft.com/en-us/download/details.aspx?id=16546 (check that is correct for your version 32/64 bit W7 etc link)

  If this does not help, try a SFC/scannow, and then try to use the above for your type of windows. -SFC https://support.Microsoft.com/en-us/KB/929833

• New monitor displays an Error Message "Signal out of range" when computer starts

  Installed new ASUS VS24H-P control on my computer and I get this image of "out of range" bouncing around the corners of the screen.

  This means that the computer sends a signal that the monitor is not capable of displaying.  It could be:

  • A screen resolution (width x height pixel size) is selected, the monitor cannot display
  • The refresh rate (Hz) is the one who can not display the monitor
  • These two

  If you have another monitor, you can plug it to visit your office. Right-click and choose the resolution of the screen, then turn it down to a 'safe' resolution like 1024 x 768 (most monitors can display this).  Then plug your new monitor back and turn the resolution back to a better suited for this monitor.

• CD/dvd drive does not work - it is recognized when the computer starts, and it is listed in the Device Manager?

  I am running Vista Home Premium on a laptop Compaq Presario F700. It is listed in the list of computers of readers, it is listed in Device Manager. The lites drive that the computer boots so I know it is detected. When you run itunes or media player the player does not open. When I push the drive button it will not open. It opens with a paperclip in the exit hole. It cannot read a CD or a DVD. None of the media players even recognize there is a disc in the drive. I tried to run fixit, but it would not drive either. I tried restoring from a previous backup, without change.

  Hello

  Check / settings (BIOS/CMOS) often F2 so watch the screen as it starts - place CD/DVD
  1st in the boot order (remember to put it at the time where the fact).

  Then put in a DVD to boot Windows and see if the driver works.

  If it doesn't then it's a hardware problem.

  =======================================

  If the drive has worked in the test above, that these can help:

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• On the computer, it does not load XP but goes to the XP start and says: NVRD32.sys file not found

  On start-up the computer, it does not load XP but goes to starting XP, and says NVRD32.sys file not found. I have to go up to xp home line manually and it load. How to fix the problem, so he starts xp automatically without entering start xp
  Thank you

  Posing for the PC model, you show that you do not know the answer, it was a software problem, but you're right, it's a Dell.
  In any case, I found the answer elsewhere, must with the boot.ini file on XP

• Get beeps when the computer starts and does not start

  Original title: Hello I have Mo Intel DG31PR & 2 GB Transcend RAM while the switch on it give beep 4 times and you would be in this case for several attempts does not start and it begins so please help and what is the problem?

  Nothing more to say

  Pravin Dave

  Hello PravinDave,

  If we get the beep codes and the machine will not move past, then we have hardware problems.

  You will need to contact your hardware manufacturer for more information on the beep codes and their meaning.

  Best regards

  Matthew_Ha

• I opened my control panel, click the game controller and his party. How can I get that back

  my game controller is gone he was there and now his party. Can I use my game controller some how the driver who was on my computer that control the game controller is gone and I don't know where he is and what has happened. can someone show me how to or tell me how to recover my controller. send me a link.
  Thank you

  Hi Reynard7,

  1. what game controller you are using?

  2 did you change on your computer before this problem?

  You can perform the system restore to revert to the previous state when it was working fine:

  a. click Start, type system restore in the Search box and then in the list click on the system restore program.

  If you are prompted for an administrator password or a confirmation, type your password or click continue.

  b. in the System Restore dialog box, click choose a different restore pointand then click Next.

  c. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  d. click Finish.

  System Restore: frequently asked questions

  Hope the helps of information.

• I got Facebook on the left of the LR 6 and he disappeared. How can I get that back?

  I had Facebook on the left side of the LR 6.  His is no longer there. How can I get that back

  [Duplicate message deleted... post the same question more than once is confusing... MOD]

  [This is an open forum, not a direct line to Adobe support... you have to wait a response]

  [Read https://forums.adobe.com/docs/DOC-7273]

  [Moved from the living room Forum to forum specific program... MOD]

  1 make sure you are in the library by window > library.

  2. make sure window > panels > publish Services is checked.

  Do you see the Facebook to publish the server now?

• Need to do a system restore. When the computer starts and I cannot access the BIOS menu - help please... (WinXPSP3)

  I need to change the boot order, so the installation CD starts first-I can't enter the Bios at Startup Menu.

  It's a HP Pavilion that says F1 is supposed to allow me to access the menu of the BIOS at startup.  I also tried:

  Tip There are other keys that provide access to the BIOS. They include the following:

  o F1

  o F2

  o F10

  o, CTRL + ENTER

  o ALT + ENTER

  o, CTRL + ALT + ESC

  o, CTRL + ALT + INSERT

  And kay LED does not work either.  It's Windows XP - 32 bit home.

  Service Pack 3 is installed - SpySweeper is anti-virus and using the Windows Firewall.  This computer were of Trojan horses (40) and finally the browser was re-directed.

  Thanks for any help.

  It shud be a Hp tool installedon your system with which you can edit boot options even after logging on to XP.

  Its something like HP or Credential Manager protection tools.

  Maryse Agarwal