Error screensaver

Similar Questions

• Satellite U400-112: impossible to format the local drive (damaged MFT?)

  Hello!

  I had a pretty serious problem with my HARD drive.
  250 GB HARD drive
  C: 116 GB - NTFS - Windows XP (Vista initially)
  D: 1, 5 GB - NTFS - (Vista Recover?..)
  E: 117 GB - RAW (was NTFS prior to crash)

  Local drive E: MFT have been damaged because of the virus attack (I hope not because of my madness!). It's NTFS, now it's RAW. I got all the necessary data partition with program ZAR, but all my attempts to recover or just the format E: remained unsuccessful.
  None of the defective sectors found on the HARD drive. Standard Windows tool to format the disks fails: 'it's impossible to finish the formatting of E:

  Before this problem with the E: drive, I had several problems with HARD drive. I have never divided re discs, to Partition Magic from the beginning he identified incorrectly. I tried Partition Magic 7 and 8.
  Link: [error screensaver | http://cs1498.vkontakte.ru/u169802/154397/x_3a82b4fb.jpg]

  The problem is that the special programs (I tried "find and Mount") also could not identify partitions to correct the defective MFT. I thought that low-level format can help me, but I heard, that the use of all applications for other producers can probably destroy my HARD drive. Are there only special applications of Toshiba developed for such cases? Or you can advice me something else?

  Thanks for your help!

  P.S. These applications did not help me:
  Find and Mount (can't find the HARD drive)
  Acronis Recovery Expert (does not find the HARD drive)
  OnTrack EasyRecovery Professional (does not resolve the error, but help to recovery data)
  HDD Regenerator

  Thus you get back all your important data?

  I would like to just launch Recovery to restore the HARD drive to its factory condition. If the recovery fails, you can try to delete the partitions with FDISK from a startup MS-DOS disk. Free bootdisks can be found at www.bootdisk.com

  FDISK can also repair a Master Boot Record by running this command: FDISK/MBR
  But it is not 100% reliable, it could cause more harm than good.

• Problems in using images for screensaver - error preventing the slide show

  original title: problems in using images for screensaver

  I always enjoyed using my photos for a screen saver.  Now, I get the message "an error prevents the slideshow to play."  How can I find and fix the error?

  Hello

  Did you change your computer?

  I suggest you to follow the steps and check

  a. go toC:\Users\ \AppData\Local\Microsoft\Windows Photo Gallery\Pictures.pd4
  and rename "Pictures.pd4".

  It can also help to remove all the video of the target directory files, although the screen saver will play some video formats.

• Screensaver error message: disk Photoscreensaver.scr - No.

  I use Windows 7, as installed on my Dell Optiplex 780.  When my screen turns the screen saver, I get the error message above-titled with the following message: "there is no disk in the drive.  Please insert disk drive\Device\Harddisk2\DR2. »

  I got the same message from before I went to photo screensaver and the default saver was installed, except the header to the message was 'WXLPGSS '. SCR - No disk"this seems to be an error in the software, as the program seems to be the content of my hard drive search.  I had two different (not at the same time), anti-virus programs and the results are the same.

  Missions, this seems to be a software problem that Microsoft should fix.  Can someone tell me how to disable this option?

  Hi Tobymugster,

  You can get this error message when you have a player that is removable, configured as drive C letter or when there is actually no removable drive.

  To resolve this problem, you can change the assignment of drive letter for the removable drive to one letter other than C.

  Go to the link below to change the drive letter of a drive in Windows 7.
  http://Windows.Microsoft.com/en-us/Windows7/change-add-or-remove-a-drive-letter

  Hope this information helps

  Bindu R - Microsoft Support
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Screensaver - Windows Live Photo Gallery - error 'an error prevents this slideshow to play' message

  Thank you for your time.
  On a new installation of Win7Pro screensaver Photo Gallery does not work as you wish.
  It is set up for the default value of C:\USERS\***\PICTURES.
  This setting causes the error.
  If I select a subdirectory of it, it works fine.
  Resolutions or ideas would be greatly appreciated.
  Thank you for your support.

  Bill Wilson
  E-mail address is removed from the privacy *.
  Bill Wilson

  Hey Wilson,

  This problem may occur if you have any other type of file outside of image files that are stored in the photo folder.

  I suggest you to check that all the files in the folder of photo image files. If you find other types of files as the video file or a music file or any other type of files, I suggest going the other files except the file image to a separate folder or another location and check to see if the screensaver in the photo gallery works just fine.

  I hope this helps. Let us know the status.

  Thank you and best regards,

   

  Srinivas R Microsoft support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Screensaver connection error: Direct3D 9.0 is required to run this screen saver, but cannot be found. Please install the latest version of DirectX and try to re-run the screen saver.

  Original title: error Login screen saver.

  When at the login screen Windows screen saver is not running. The circle of 'thinking' of the mouse pointer starts to turn, but it just goes back to the login screen. I created all 4 strings in the HKEY_USERS\. Default\Control Panel\Desktop\ including ScreenSaveActive = 1, ScreenSaverIsSecure = 0, ScreenSaveTimeOut = 60 and SCRNSAVE. EXE = C:\Windows\(our custom screensaver). Instead of our custom screensaver I also put the windows mystify screensaver in the key but the Directx 9.0 3D error pops up. Any suggestions?

  Note: The Customs and the Windows screen savers that work both when a user is connected.

  UltraVNC seemed to work very well with win 7, but the only software of remote that I know works without fail and control on a very consistent basis, is the enterprise version of RealVNC. Yes, it costs money, but it is comparable to microsoft RDP, with additional features. They have a free version that does not cost any money and it's missing a few features. In a corporate environment, I am sure that this version is a no no.

  ' Windows XP ' My Pictures Slideshow "screen saver. ssmypics. SCR

  See: http://www.google.com/support/forum/p/Picasa/thread?tid=78ca9579242d3682&hl=en for more details

• error trying to start the screensaver from microsoft on Windows 7 Dell computer lagoon

  I have a new duo inspiron dell running windows7 32 bit with a processor of 1.5 GB and 2 GB of ram. whenever I try to start the lagoon screensaver I get the following error. "Your computer has no resources available for the Saver screen of lagoon or system requirements.

  The screensaver of the lagoon is not included with Windows 7 and is not supported as part of the operating system.

  If it solves your problem, click on the link "Propose as answer" below and vote as useful by clicking on the green triangle for the lelft. Thank you!

• I get the error next message each time that my screensaver trys to activate: screen saver: PhotoScreensaver.scr - bad Image

  Screen saver: PhotoScreensaver.scr - bad Image

  C:\Windows\system32\MSVCR100.dll is not designed to run on Windows or it contains an error. Try to install the program by using the original installation media or contact your system administrator or the provider of software for support

  This screensaver previously worked, quit not sure why he stopped.

  Anyone know of a cure for this error message.

  Hello

  Were there any changes (hardware or software) to the computer before the show?

  Install the Microsoft Visual C++ Redistributable dll, which is necessary for the projects generated with Visual Studio 2010.

  Download the files below according to your operating system version. I would setup versions because they may be needed for different programs. Check in programs and features, you show that you have installed Microsoft Visual C++ 2005 Redistributable and Microsoft Visual C++ 2008 Redistributable? If this is not the case, download the links here.

  Package redistributable Visual C++ 2005 (X 86)
  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=32BC1BEE-A3F9-4C13-9C99-220B62A191EE&displaylang=en

  Visual C++ 2005 (x 64) redistributable package manager
  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=eb4ebe2d-33c0-4A47-9dd4-b9a6d7bd44da&displaylang=en

  Package redistributable Microsoft Visual C++ 2008 (x 86)

  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=9B2DA534-3E03-4391-8A4D-074B9F2BC1BF&displaylang=en

  Microsoft Visual C++ 2008 SP1 Redistributable Package (x 64)
  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=BA9257CA-337F-4B40-8C14-157CFDFFEE4E&displaylang=en

  Package redistributable Microsoft Visual C++ 2010 (x 86)
  http://www.Microsoft.com/download/en/details.aspx?ID=5555

  Package redistributable Microsoft Visual C++ 2010 (x 64)
  http://www.Microsoft.com/download/en/details.aspx?ID=14632

  Hope this information helps.

• In Windows 8, an error prevents the slideshow to play as screensaver, also error when playing YouTube videos and no sound on videos

  Everything was working fine a week ago and I never changed anything, but my screen of sleep (Windows Live Photo Gallery), stopped working and I got this error message.  As it happened, when I try to play videos YouTube I get an error message and it tells me to try again later.  Videos in other formats will play, but there is no sound on any of them although when I run the maintenance program it says there is no problem with the sound.  I don't know which is the case because I tried some fixes, I found on the internet and the screensaver CAME and returning for a day, but then stopped working again the next day.

  This question was asked before with earlier versions of Windows, but no one seems to have found a permanent solution?  Help, please.

  Hello

  You can run the SFC tool and check if that helps. SFC/scannow is a very useful command that you can use in any version of Windows. When the SFC (System File Checker) command is used with the/scannow switch, the tool analyzes all the important files of Windows on your computer and replace if necessary. Missing and the corruption of the operating system (like many DLLs) files are probably the main cause of the major problems of Windows.

  See the following steps to perform a scan SFC:

  (a) press the Windows key + X, select the prompt (Admin) to bring up the elevated command prompt.

  (b) in the command prompt, type the following command: sfc/scannow then press ENTER.

  (c) after the scan, restart the computer and check if the problem persists.

  Response with the State of the question and we will be happy to offer you our help.

• Change the screensaver to logon and get this error message - is required to run this screensaver Direct3D 9.0, but cannot be found.

  I changed the idle screen to login to one of the windows Vista by default (ssText3D.scr).  and I get this message:

  Direct3D 9.0 is required to run this screen saver, but cannot be found.  Please install the latest version of DirectX and try to re-run the screen saver.

  DirectX is installed. The screensaver works if someone is logged even if it is locked, but not to the logon screen.  All the patches?

  Hi pfdr70,
   
  1. are you able to apply other screensavers?
   
  We recommend trying the following steps and check the result.
  Step 1: Download and install the latest video card driver.
  1 visit the system manufacturer's Web site, download the Vista compatible video card driver and install it.
  2 restart the computer so that the changes take effect after the driver installation.
   
  Step 2: Set the monitor to display better.
  See Get the best display on your monitor
  Step 3: Enable graphics acceleration.
  1. open display settings by clicking the Start button, clicking Control Panel, on appearance and customization, personalization, and then clicking display settings.
  2. click on display settings, and then click Advanced settings.
  3. click on the Troubleshooting tab, and then click on change settings.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  4. move the slider full hardware acceleration.
   
  See Run the DirectX Diagnostic tool
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Screensaver Vista Error Messages

  I pushed the ctrl + alt + down arrow arrow and my screen is black then I pressed ctrl + alt + arrow pointing upwards and my screen got really big with a large font size, so I changed the resolution of the screen back to normal.  I left my dell inspiron 1525 for a few minutes and then when I came back to it, instead of my usual screen saver, he said "the screen saver can't run because it requires a more recent or Direct3D-compatible video card.  Also, when I try to change the resolution of the screen now it won't let me or an error message appears.  Any ideas on how to solve this problem?

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work:

  http://support.Dell.com/support/downloads/index.aspx

  Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  Then:

  http://Windows.Microsoft.com/en-AU/Windows-Vista/change-screen-resolution

  Change the screen resolution

  Screen resolution refers to the clarity of the text and images on your screen. At higher resolutions, items appear sharper. They appear also smaller, so more items adapted to the screen. At lower resolutions, fewer items adapted to the screen, but they are larger and easier to see. At very low resolutions, however, images may have serrated edges.

  See you soon.

  Mick Murphy - Microsoft partner

• error-not find macrmedia flash

  periodically, I get a pop-up error message that says "macrmedia flash cannot be found. My adobe flash player is up-to-date and functional. Why do I get this message?

  I think the solution to this problem. The issue is the screen saver. The problem started when I installed a screen saver. So I thought that maybe the screen saver uses flash . So I uninstalled the screensaver and then reinstalled the screen saver and no more "error message-can not find macromedia flash.

• DAQPad-6020E 10402 error message

  I am running Labview 2010 and a USB DAQPad-6020E.

  I wrote the code to read 1 sample per second, using "HAVE them sample channels - only Point of waveform.

  Everything works for a while, but then it comes up with the error message "error-10402 to AI simple Scan.

  The possible reasons - no device is located at the specified location...

  Looking at the forums looks like it's Windows XP, try to be effective and when he goes into the screen saver turns off the USB port.

  Anyone else have this happen to them and what did they do to this topic?

  I can not turn off the screen saver as it is the policy of the company for the screensaver to kick after 15 minutes and also have it so hard drives don't turn off.

  Hey TC,.

  It is a problem that I've heard of before, there is an example of a community that may be useful.

  Toggle Windows Screensaver with LabVIEW: http://decibel.ni.com/content/docs/DOC-12290

  However, this VI accesses your Windows registry database so I would use it at your own discretion.

  The only other thing I can think of is to check your control panel energy saving settings, see if there are options for the USB ports...

  Take a look at this: http://www.himsa.com/Support/NOAHlinkKnowledgebase/Howto/turnoffaUSBportspowersaveoption/tabid/492/l...

  Or this:

  http://helpdeskgeek.com/Windows-XP-Tips/prevent-Windows-from-powering-off-USB-device/

• System hangs when the computer sleeps with error KMode_Exception_Not_Handled after generation installed 9926

  Since the new version update (9926), whenever my computer goes to sleep or when it is left for several hours compress I get unhandled KMode Exception error.  I deleted a suspicious program who has problems during the previous generation, but that made no difference.  When the computer restarts, I wonder if I want to use the previous windows platform and I encounter the KMode problem, but after a day or two, the computer did an update to 9926 and I started having the problem again.  I looked for all devices that are evidence of a driver problem and have not found any.  Tech is able to examine the file DMP to give me a clue as to the program/device must the fixed driver so that I can get past this error?  Here is a link to the folder that contains the file.

  https://onedrive.live.com/embed?CID=932A5B907D806E8A&RESID=932A5B907D806E8A%21225306&AuthKey=AMaX68Y4-fpbXcE

  I looked in the pilot and I have the most up to date, but I was able to solve the problem until the next update by turning on my screensaver and do not allow the HARD drive to sleep.

• Vista Start black normal & all Security Modes, restore fails, screensaver ŒUVRES

  Yesterday (18/06/09) I installed a few new updates, but is not a restart.  Today, the system was sitting idle (, but nobody use it) and we had a power failure.  Restart the system wanted to make a volume control.  During the audit, he found a bunch of bad index entries.  The files went flying by pretty fast, but I could tell that many of them had something to do with Media Center.  Then later in the repair of the volume, she added a bunch of orphaned files.  I couldn't give a sense these files because all the entries were similar to Hex IDs.

  So that brings us to today.  The system starts with black screen with a mouse pointer.  System knows I have 2 monitors connected & I can move the mouse between the two monitors.  With the help of other boots (via F8 in the boot menu) produced similar results, except in safe mode boots, the system does not know the 2nd monitor.  CTRL-ALT-DEL does nothing.  (Do NOT bring up the Task Manager.)  The SHIFT key to display the Sticky Keys dialog box.  After a while, the screen saver turns on.  With screensaver KB/mouse activity outputs and system back to black screen.

  All the security startup black screen Modes.
  Low-resolution video starts with black screen.
  Black screen on startup of the diagnostic Mode.
  Directory Services Restore Mode reports all my disks are clean and black screen on startup.
  Sleep key works.  Wake up, the system returns to black screen.

  OK, here's a little recap... BLACK SCREEN!

  So next I tried the repair your computer...

  Log in to my account admin OK.  Then I tried to Startup Repair which could not detect a problem.  Then I tried the system restore.  System Restore is all my restore points registered in April ' 09.  System Restore Gets an error and fails to load any restore point.  I have two different messages depending on what point of restoration, I try.

  2 most recent restore points are of yesterday and today and the updates, I just installed but never rebooted before the power failure disk check.  When I try these 2 restore points, I get the following:

  The configuration register is corrupted. (0x800703F1)

  If I try the old restore points, I get:

  Cannot open the file transactionally, because its identity is function
  on the outcome of a transaction not resolved.  (0x80071AA7)

  Reading through the error of this last web messages makes me think to there is a bad dependency in the update / restore of the system process.  If pending updates become corrupt, old restore points will fail.  Is this true?
   
  I can boot from a CD-ROM of 3rd party and see my programs and data on the disk.  I did a full inspection, but it seems that all of my stuff is still there.

  So finally I tried to reinstall my Vista system, and my only option is to replace my entire system.  The update option is grayed out.  I used to be able to do a re-install/upgrade to update in the old days (XT & before), but it seems that it's not possible with Vista.  It would be great if I had my old system before SP1, and then I could re - install SP1 & all of my updates.  But it would be impossible for me to recreate my 1 TB from scratch system.  Simply, I have enough DVDS to back up a lot of data.

  Is there a solution to my boot at the digital black problem, or I'm really screwed?  A reasonable solution is much appreciated.

  ==============

  UPDATE...

  I can access shared folders on the blackened on Vista machine.  I created my user account on another computer (Win XP) and am also able to access all my user files.  In addition to the screen saver and the sticky keys work, it seems that file sharing works also.  However, the printer share and office remotely (using Ultra VNC) do not work.

  Hey Ken, I just reread your post previous and tried your procedure.  Are your steps to perform a repair install on Windows site:

  1. Insert the Windows installation disc in your computer's DVD or CD drive. You must start Windows installation while running your existing version of Windows.

  2. on the Install Windows page, click install now .

  3. on the get updates for installation page, we recommend getting the latest updates to help ensure a successful installation and to help protect your computer against security threats. You will need an Internet connection to get the installation updates.

  4. on the Type your product key for activation , we strongly recommend that you type your 25-character product key in order to avoid problems during activation.

  5. on the page Please read the terms of the license , if you accept the license terms, click I accept the terms of the license .

  6. to the which type of installation you want? page, click upgrade to begin the upgrade. You can see a compatibility report.

  7 follow the instructions.

  Note : If your installation disc doesn't include SP1 , and you are updated, then you must uninstall it before proceeding with an update install. Start-> Control Panel-> programs-> see installed updates , then select Service Pack for Microsoft Windows and click on Uninstall.

  Unfortunately, I'm stuck on the first step.  Start a Windows installation when executing my existing version of Windows when my existing version of Windows starts with a black screen, and the only interaction of console, I am able to do what a screen saver and the Sticky Keys dialog box?  What is the trick to start installation?  I can't find.  Is there a way to launch the installation with the keys dialog box to sticky?

  In addition, in the case where I, how to uninstall SP1 from a black screen?  The dialog box of the sticky keys which they as well?

  I know that other messages that other users could not bring up the Task Manager with CTRL-ALT-DELETE.  As I said in my original post, I can't do it.  THE ONLY THING THAT WORKS FOR ME IS THE STICKY KEYS DIALOG BOX.  So I do not buy any version of Vista at all costs will have what I need because Windows Vista just can't do a re - installed on-site if your Windows Vista is not running after a black screen.  Right?

  I'm getting very frustrated and would be very grateful for any help.  I just can't figure how to get the computer do anything when the only thing it starts is a black screen.  And none of my restore points can be restored.  I thought that the system restore has been the goal of the restoration of the system.  Why my Vista system locks my system restore? I don't understand!

  I think that this last update not to not fill properly and locked up my system.  Is it possible for me to undo than a black screen or a Setup disk?

  BTW, Western Digital diagnostics transmitted without error.  Then at the command prompt on my Vista disk, I ran chkdsk and it fixed some files.  I think they were just left by a system restore failed.  So I ran sfc from the command prompt using sfc/scannow damaged = c: \ /offwindir = c:\windows.  He ran for a while and there was no violation of integrity.  If the drive seems fine.  Are there tools that can help me find the problem?  Is that what I can do to restore the registry to an earlier time manually?