ESXi 4.1 e TSM for virtual environment 6.4.1

Similar Questions

• addition of virtual machine / Server esx for production environment

  Hello

  How can we add virtual machine or esx server for production environment?

  In general... As his "simple terms?

  Install ESXi host

  Install, run and connect to the host via the gateway client installed from the host on an external workstation

  Then

  OR THE OTHER

  Install and run the converter on each physical computer that you want to become a virtual machine

  Once finished, turn off power to virtual and physical.

  OR

  Create a virtual machine and install the o/s CD drive.

  What you want is way off the coast without 1 million questions about your installation.

• Use the diskette of esxi for virtual machines

  Hello
  I would like to set up a lab and I have hp g6 server but just with a single 600 GB sas disk
  is it possible to install esxi on it and also use it as a storage device for virtual machines on?
  I know that I can install esxi on a cool drive but if what I've said, it's possible I prefer to use that
  Thank you very much

  It's true.

• ID in a virtualized environment

  Can someone develop an IDS solution for a virtualized environment?

  I have ESX/ESXi - highly virtualized blade servers.  IM using the blade passes under chassis e/s - no pass-through.

  The requirement is to run a service IDS such as VM-on-VM traffic is controlled. The traffic flow can be between two virtual machines on the same blade, 2 virtual machines on two separate blades in the same chassis, or two separate virtual machines on two hunts...

  In this case, I see 3 streams of traffic off of the bat...

  blade even: vm-on-vm traffic is enabled by a hypervisor type switch (vDS 1000v or vmware).

  different blades in the same chassis: vm-on-vm traffic will leave blade and can be set by hardware chassis (blade chassis I/O) switch.

  different chassis: vm-on-vm traffic will have to go to ToR (maybe same end of line).

  NOTE: If the VMs are on different VLANS, traffic will always be at the end-of-line/agg switches (the limit of L3/L2).

  So, given all of these possible flows, what is the best way to go about deploying IDS service? Implementation? Virtual or physical? etc...

  Thank you!

  You're right, dragging the flow of vm virtual machine out of the box for the inspection of the IPS and stuffing then reconnect will be a bottleneck of bandwidth. I doubt that it would cost you more CPU to move these pieces sttings to launch an IPS sensor inside the box (ala Sourcefire).

  To minimize the bandwidth bottleneck, you can add Ethernet interfaces to your ESXi server and even to group several togther if you need more bandwidth, a single pair can offer.

  -Bob

• Application error "not enough of space for the environment" in Vista.

  Could not find the right answers out there for this problem. Application error "not enough of space for the environment '. I am running Windows Vista Home Premium. Thanks for your help!

  I suggest you try compatibility mode.
  If the program is not compatible, then you try to install and run the program in compatibility mode.
  Use the following steps:
  (1) right click on the program
  2) click Properties
  3) click on the Compatibility tab
  (4) select run this program in compatibility mode and select Windows Vista or other operating system, the program has been run successfully.

  Check out the link here: make sure to run older programs in this version of Windows
  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows

  If you are running Windows 7 Professional or Ultimate version, install Windows Virtual PC and Windows XP mode (http://www.microsoft.com/windows/virtual-pc/default.aspx) and run your software in Windows XP.

  If you run Windows 7 Home Premium, you cannot run Windows XP mode, but you can try VirtualBox (www.virtualbox.org) or VMware Player (www.vmware.com), or any other 3rd party software virtualization and install a separate copy of Windows XP (family or professional edition) for this purpose. You can find the virtualization software free that will run on Windows 7 Home Premium.

  Let us know if that helps.

  Marilyn

• Windows 7 Home Premium with invalid Code of Activation in the virtual environment

  I have a PC with Windows 7 Home Premium, I could get the Product Code of Magic Jelly Bean KeyFinder.  I created a Virtualbox Win7 environment to test the code for what should I have to rebuild my computer I have everything properly.  Although I enter the code correctly when I try to activate it says that is not valid.  Is it because I'm under a system with it already running with the same product code that it does not work properly? Or something else?

  If your intention is to rebuild the desktop, why would need to test the activation code to see if it works, when it is currently working on the host itself? I can understand the Windows 7 Home Premium assessment in the virtual environment, but the idea of the code itself, no.

  If its already active in the host, then that means it works.

  If Home Premium from Windows 7 is pre-installed on the host itself, the code that you use cannot be used to activate Windows 7 elsewhere.

  New computers coming often pre-installed with Windows 7 have what is called a recovery partition. This is used to reinstall an operating system in the case of a system failure. To access it, you need to start when you start your computer by pressing a function key. This can be either F1, F2, F9, F10, F11, F12 key DEL or tab. See the manual that came with your PC for instructions on how to reinstall Windows.

  This is how the recovery partition is accessible to most popular brands...

  For Dell, press F8 on the keyboard until the Advanced Boot Options menu appears on the screen.

  For HP, press F11 directly after switching on the device

  For LG, press F11 directly after switching on the device

  For Toshiba, press and hold "0" BEFORE and during the power upward

  For Acer, press and hold ALT + F10, as soon as you see the logo

  For Asus, press F9, as soon as you see the Asus logo.

  For Samsung, press F4 to the power upward...

  For Fujitsu, press the F8 key directly after the power

  Advent, restart your computer. Then, press F10 repeatedly until the message "Starting system recovery"

  Sony VAIO, reboot and press "F8" or "F10" repeatedly until the screen "Advanced Boot Options".

  If it is a retail license and you need to reactivate Windows 7 Home Premium if you reinstall from scratch, you can still use phone activation:

  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
  http://support.Microsoft.com/kb/950929/en-us

  Go to the properties of the system of the host machine (start > right click computer > properties > scroll to the bottom of the window). If you see OEMS in the ID of the product you can not use elsewhere:

  

• Supported high availability in a virtualized environment

  Hi guys,.

  is it supported software such as Veritas Cluster Server cluster in a real operating system in order to have the high Avalibility for my message store?

  According to the release of the latest Suite of Communication of information, it would be possible, any ideas?

  https://wikis.Oracle.com/display/CommSuite/common+release+information+for+Communications+Suite+7.0.6#CommonReleaseInformationforCommunicationsSuite7.0.6-SystemVirtualizationSupport

  Thank you

  Caius

  As indicated by the release notes as you pointed out, UCS does not specifically support or does not support any given platform virtualizataion - the virtual machine solution must be completely transparent to the application. If the OS and HA solution is supported by the UCS and HA solution running support in this virtual environment, then it is supported.

• FQDNs for ESX environment when DNS servers are VMS within the ESX environment

  Hello

  I was wondering,

  When the implementation of a new infrastructure from scratch, with an ESX cluster from scratch

  and when the servers DNS themselves will run inside the cluster,

  Then, it is advisable to use IP addresses instead of the domain name COMPLETE for the right ESX environment?

  Here's what I've done so far:

  -installed 1 ESX host

  -installed donain controller as VM

  -installed PSC and VCSA

  -created the new cluster

  -installed the second ESX host, added to the cluster.

  I installed a VM DC as the first thing after the installation of the initial ESX host, I could have started using the domain name COMPLETE for the ESX environment at this time.

  However, I didn't do it.

  For installation of the VCSA and when you add ESX hosts to the cluster, I used IP addresses instead of the FQDN names.

  It seems stupid and dangerous for me to use domain COMPLETE the ESX hosts themselves, because the domain controller is running in the cluster.

  So I used IP addresses only to ensure the ESX HA cluster and the characteristics of heartbeat stay ok if something were to happen to the DNS server.

  However, the VCSA installation and when you add hosts to the cluster,.

  the MISTLETOE gave me a warning, indicating that it is preferable to provide a FULL domain instead of an IP address name.

  I am of the opinion that if you have no physical DNS servers, it is not a good idea.

  My opinion is that when your nameservers inside the ESX cluster itself and you do not have 2 redundant external DNS servers, so it is not wise to use the FQDN for your ESX hosts, PSC and VCSA setup.

  In my view, using the property intellectual property is much safer in this case.

  I was wondering what is your angle on it.

  Do you see the same way, or have different opinions?

  Hi smetter,.

  It is advisable to have a working DNS for vSphere environment however the use of DNS for things like vSphere HA have been removed in more recent versions of the product. Refer to the section of the guidelines of the general network of this document for more details: https://www.vmware.com/files/pdf/techpaper/vmw-vsphere-high-availability.pdf

  With this in mind I wouldn't be worried about use of FULL domain for the addition of services like the ESX host, etc.. Failure where HA would be restarting the virtual computer, there is no dependency on DNS so it will continue to work as expected and, subject to the availability of resources the virtual machine starts on another host.

  According to your vSphere licenses, you may also like to consider the implementation of anti-affinity DRS VM to keep your DNS Appart servers and on different hosts. This can prevent your servers DNS are declining when the failure of a host. You must have Enterprise edition or later for this.

  Kind regards.

• Models for virtual environments

  Hello

  I want to check the respect of the virtual environment. I've seen a few models in photos showing VCM (such as "VMware vSphere 4.0 Security Hardening Guide" on the VCM on VMware Web site product page - see attachment) but my installation has none of them. So my question is what do I have to create my own templates from scratch or is there models "out of the box" to apply for VE. I use vCM 5.6.

  Thank you.

  For models to be imported, you need run the content of the host of collector VCM Wizard. Make sure to import what you need because they can be quite resource intensive.

  For content Wizard works, you have a VCM + license compliance model.

• OPA on virtualized environment

  Hello
  
  It is used to recommend that the duration of the OPA has been run on a physical server, but there is a growing demand to run on a virtualized domain. The operation of the OPA on a virtualized environment affect the model of supported somehow; i.e. the Oracle will support the OPA on a virtual server rather than physical?
  
  Thank you

  You are welcome Roger,.

  For Oracle VM - we fully support this end to end, if you are using a supported operating system.
  For VMWare - we support fully, as long as you are (a) using a supported operating system, and (b) it can be demonstrated that the problem occurs when you do NOT run on VMWare

  Davin.

• How does vcenter distribute CPU and carrots in particular for virtual machines?

  Hi, so we have about 50 vms on 4 hosts in cluster.

  Each VM has got 1 vcpu assigned to them. Today, I had a developer tell me it is terrible, it was because he wanted to tell once the cpu is pegged at 100%, nobody else could do anything on the machine.

  This raised an interesting question: how vmware does manage the underlying and carrots individuals host CPU?

  If I give 2 CPUs in a machine, it maps to the physical CPU underlying, or is he underlying host carrots?

  And finally, if I assigned 2 processors to each vmachine, will I see performance degradation in the cluster to compare to just assign a?

  See you soon!

  Hi, so we have about 50 vms on 4 hosts in cluster.

  Each VM has got 1 vcpu assigned to them. Today, I had a developer tell me it is terrible, it was because he wanted to tell once the cpu is pegged at 100%, nobody else could do anything on the machine.

  It would be the case with a physical machine if a processor is pegged at 100%, that it is 100% not different between physical and virtual I'm afraid.

  This raised an interesting question: how vmware does manage the underlying and carrots individuals host CPU?

  First of all, it is not vCenter which manages the planning of CPU is the individual host servers.  read the following doc for a very good idea to schedule of CPU

  http://www.VMware.com/files/PDF/perf-vSphere-cpu_scheduler.PDF

  If I give 2 CPUs in a machine, it maps to the physical CPU underlying, or is he underlying host carrots?

  If you have a guest 2vCPU it will use carrots 2pCPU

  And finally, if I assigned 2 processors to each vmachine, will I see performance degradation in the cluster to compare to just assign a?

  You mileage may vary, but it is not considered best practice to create comments vSMP without good reason, it will increase the pressure on the CPU scheduler on the host servers.

  See you soon!

  If you have found this device or any other answer useful please consider useful or correct buttons using attribute points

  Tom Howarth VCP / vExpert

  VMware communities user moderator

  Blog: www.planetvm.net

  Writer on "[vSphere of VMware and Virtual Infrastructure Security: securing ESX and virtual environment | ]. http://www.Amazon.co.UK/VMware-vSphere-virtual-infrastructure-security/DP/0137158009/ref=sr_1_1?ie=UTF8&s=books&QID=1256146240&SR=1-1]'. Currently available on roughcuts

• public network for virtual machines, private storage and the service console?

  Hello

  So far I had a pretty small facility with 2 servers with 4 physical network adapters each running ESX 3.5, a small box of EqualLogic SAN to shared storage and a few virtual machines on our network of regular reinforcement, routed, not on a private.   The network config was really simple.  I just put everything on real IP addresses on our network of building.

  Now I want to move the SAN and the traffic on a private service console network, but I don't know how to do this.

  Right now I use 2 NETWORK cards on each server:

  vmnic0 is configured on vSwitch0 and has the network of the VM on it that all my use of VMS to talk to the outside world, and it also has the Service Console that uses Virtual Center and I use ssh to it.

  vmnic1 is configured on vSwitch1 and a VMKernel Port and also a Service Console Port for iSCSI Software to talk to my SAN.  (never been clear on why both are needed to talk to the SAN, but doctors say they are)

  My plan is to set up a vSwitch2 and bind it to vmnic2 and implemented a VMKernel Port and the Service Console Port for software iSCSI on the 10.x.x.x network, set up my new (larger) SAN box on the 10.x.x.x network and simply use Storage vMotion to move virtual machines to the new storage space.  As soon as I did this, I would like to not use the Service Console on vSwitch2 and not a Console Service at all on vSwitch0.  Is it possible to delete the one on vSwitch0 and just use a new vSwitch2 for Virtual Center and ssh access?

  So my proposed configuration would be:

  vSwitch0: VM network only, used by the VM guests for oriented public access network, no construction of Network Service Console, linked to vmnic0

  vSwitch1: superfluous once I do storage vMotion of everything on my old SAN, will eventually remove and pair vmnic 1 with vmnic0, linked to vmnic1

  vSwitch2: VMKernel and Service Console on the network 10.x.x.x, used to access the new SAN, used by Virtual Center to access the ESX, used to SSH in to ESX on private network, associated vmnic2

  If it works?

  Thank you.

  Hello

  VMkernel ports cannot live on the same subnet. So if you have 3 vmkernel ports say: vMotion, iSCSI and NFS. You really need 3 subnets. 1 for each vmkernel port.

  Otherwise how does he know all send properly?

  Best regards

  Edward L. Haletky VMware communities user moderator, VMware vExpert 2009, url = http://www.virtualizationpractice.comvirtualization practical analyst [url]
  "Now available: url = http://www.astroarch.com/wiki/index.php/VMware_Virtual_Infrastructure_Security' VMware vSphere (TM) and Virtual Infrastructure Security: securing the virtual environment ' [url]
  Also available url = http://www.astroarch.com/wiki/index.php/VMWare_ESX_Server_in_the_Enterprise"VMWare ESX Server in the enterprise" [url]
  [url =http://www.astroarch.com/wiki/index.php/Blog_Roll] SearchVMware Pro [url] | URL = http://www.astroarch.com/blog Blue Gears [url] | URL = http://www.astroarch.com/wiki/index.php/Top_Virtualization_Security_Links Top security virtualization [url] links | URL = http://www.astroarch.com/wiki/index.php/Virtualization_Security_Round_Table_Podcast Virtualization Security Table round Podcast [url]

• How to monitor the TX and RX on PERFORMANCE for virtual network adapter BASP monitor?

  How to monitor the TX and RX on PERFORMANCE for virtual network adapter BASP monitor?

  I have a virtual network adapter that is created with Broadcom.

  This virtual interface named "BASP eCard" visible on the performance monitor in the category 'Rhythm Pipe' but not in the category "Network Interface".

  This is problematic because the Tx and Rx (bytes received/send in second) is available in "Network Interface" that show physical network cards only.

  Someone has an idea?

  Thank you

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)

  *

  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• any time, I try to open adobe photo shop elements 2.0 it says could not start because the volume windows uses for virtual memory did not enough of free space see windows help for more information

  When I try to open adobe photo shop elements 2.0 message that says: cannot start adobe because volume windows uses for virtual memory doesn't have enough free space, which could lead to stability problems see windows help for information can help you

  Hi gregoryandme,

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Uninstall and reinstall the Adobe photo shop program.

  Method 2: Perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow step 7 the link to start the computer to a Normal startupmode.

• vWorkspace and Foglight for Virtual Office training

  Anyone know if it is available for vWorkspace training instructor 8 and Foglight for virtual desktops?  I contacted Dell training but never received a response.

  This question is not met at the time of the request

  If you are still interested, let me know and I can run after correct people.