ESXI 5.5 - give it a static address

Similar Questions

• How to give feedback one static ip address

  I use vmware station 7.1.2.  I have windows 7 and installed ubuntu 10.04 as a guest.

  The customer is using NAT and not to change its ip address.   is there a way I can give this comments a static IP (192.168.21.133).

  ifconfig feelexit@Ubuntu:/etc$

  eth0 Link encap HWaddr 00: 0C: 29: 2 c: 70:38

  INET addr:192.168.21.133 Bcast:192.168.21.255 mask: 255.255.255.0

  ADR inet6: fe80::20c:29ff:fe2c:7038 / 64 Scope: link

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Fall of RX packets: 634 errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 41 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 46372 (46.3 KB) TX bytes: 5892 (5.8 KB)

  Basis of interruption: 19 address: 0 x 2024

  In addition to what I already said if you're looking to assign a specific IP address to a specific VM via the file dhcpd.conf on the host, this can be done by adding the following to the file dhcpd.conf target.  Note that the virtual machine must be stopped, not suspended and VMware Network Services must be stopped before making any changes, then restarted.

  Example:

  host Fedora13 {
  hardware ethernet 00:0c:29:c1:90:02;
  fixed-address 192.168.70.20;
  }
  

  In the example above 'host Fedora13' refers in the name of the configuration file of the client without spaces .vmx in even if the real name of the .vmx on my system configuration file is "Fedora 13.vmx" and "hardware ethernet 00: 0C: 29:c1:90:02;" contains the MAC address assigned to the virtual machine in the .vmx config file target in the parameter "ethernet0.generatedAddress.  I added this to the file dhcpd.conf for vmnet8 on my system, and when the virtual machine is running and the guest operating systems network card is configured for DHCP it is always assigned the address above with the correct subnet mask, IP address of the gateway and DNS for VMnet8 servers.

  ==========

  The following information I have in my notes even if IIRC it comes from a Document or a section of VMware.

  Address used on a guest only network

  Range	Use of the address	Example of
  .1	Host machine	192.168.0.1
  .2 - .127	Static addresses	192.168.0.2 - 192.168.0.127
  .128 - .253	DHCP assigned	192.168.0.128 - 192.168.0.253
  .254	DHCP server	192.168.0.254
  .255	Broadcasting	192.168.0.255

  Using addresses on a NAT network

  Range	Use of the address	Example of
  .1	Host machine	192.168.0.1
  .2	NAT device	192.168.0.2
  .3 - .127	Static addresses	192.168.0.3 - 192.168.0.127
  .128 - .253	DHCP assigned	192.168.0.128 - 192.168.0.253
  .254	DHCP server	192.168.0.254
  .255	Broadcasting	192.168.0.255

• To give my e-mail address and the password for sites engine job search?

  General question: is it a bad idea to give both my email address AND my password for job search web sites like Jobing.com, Monster.com, more recently PhoenixJobs.com? Why they need my password and force me to make sure that 'cookies' are enabled?

  It makes me nervous. Should I be?

  Please notify.

  Thank you, John Van Fleet

  Job sites don't ask you your password by e-mail. They ask you a password which can be new or old. You can use the same password everywhere or have different passwords for different sites, which is recommended. You shouldn't be nervous but cause they can't really see your password.  If this post answers your question, click mark as answer .

• Please give me an email address or other means of contact. my creative cloud does not work. I need support and adobe Web site does give no support

  Please give me an email address or other means of contact. my creative cloud does not work. I need support and adobe Web site does give no support

  To the link below, click on the still need help? the option in the blue box below and choose the option to chat...

  Creative cloud support (all creative cloud customer service problems)
  http://helpx.Adobe.com/x-productkb/global/service-CCM.html ( http://adobe.ly/19llvMN )

• Virtualized ESXi host is not assigned an IP address

  My virtualized ESXi host is not assigned an IP address on a DHCP network. I created it on my physical host with a physical NIC.

  Both its E1000 vNIC is networked with virtually the same Vswitch as the physical host, I created a second Service Console on this vswitch for the ESXi host virtualized, what I need to change the IP of virtual servers to match the newly created Service Console?

  I found a guide on changing the IP address of the vswif on the virtual host, I'm going in the right direction?

  If you run ESXi on ESX (i) then you must enable the mode promicuous on the VM host vSwitch portgroup.

  Dave

  VMware communities user moderator

  Now available - vSphere Quick Start Guide

  You have a system or a PCI with VMDirectPath?  Submit your specifications to Officieux VMDirectPath HCL.

• ESXi 5.1 gives 0.0.0.0 address

  Installed ESXi 5.1 on two IBM 3650 servers.

  The first installation went well (can point VShpere Client and everything seems good), installation on the second 3650, he gave me the IP 0.0.0.0.

  The servers are the same - even NIC.  Both machines have two network cards and all the link four lights are on.

  I tried to redo the configuration of the network (and apparently do DHCP) but always 0.0.0.0.

  Any suggestions?

  Hello and welcome to the communities.

  Looks like maybe another NETWORK card is used? I shoot all except one of the cables out and make sure you have the cable with the with DHCP subnet connected to the NETWORK card you want. Then back in the DCUI and make sure it is correct.

• ESW 520 give priority to IP addresses

  I have a LAN with IP addresses for the computers and public, static IP for VoIP phones. They are a hosted VoIP provider, and I want to give priority to the public IPs from my ESW-520-48 per switch How I implemented that in this switch?

  I have no roles assigned on ports and no configuration of VLAN either. I had tried to separate the VLAN first, but eliminated this way. It is once again all VLAN 1 now on the switch. For some reason when I put in place of the 100 VLAN for voice, the voice stopped working on phones, but data were always very good.

  Hi netguy,.

  QOS in rewriting the DSCP (dissociated Services Code Point) address IP phone range by;

  1. create an ACL that specifies the range of IP addresses with mask reverse

  2. attach the ACL on a map of advanced class, then

  3. fix a plan of class to a table of QOS policy that is configured to set a new DSCP value

  4. attach a QOS policy on an interface

  5 but you have a default Advanced QOS configuration already in place, so that should be modified or deleted.

  It is difficult if you have never played with before advanced QOS or understand the latest five statements.

  I guess that your hosted IP phones have DSCP settings (dissociated Services Code Point) already placed on IP phones or the settings that you can set directly on each IP phone?

  If it is possible, why not just move the switch to the basic QOS mode and then say the switch to trust DSCP.

  Well, it's the best thing to do.

  

  

  Best regards, Dave

• ASA - ldap - user vpn static address

  Hello!

  I am trying to configure ASA to assign a static IP even to some user (User1) every time when it connect to the network via the AnyConnect client. We have Windows AD and that you are using the LDAP AAA server for authentication of remote access VPN users. I found in the document 'Cisco ASA 5500 Series Configuration using the CLI, 8.2 Guide' in the explanation section "Configuring external year for security device user permission to the server" and configured the ASA and user properties in AD exectly similarly:

  Firstly, I assigned a static ip address in the menu properties (section numbering) of User1 in Active Directory. Then I created the ldap attribute card where I traced msRADIUSFrameIPAddressattribute to IETF-RADIUS-Framed-IP-Address. attribute In the end, I applied this map to attribute ldap to LDAP AAA server group.

  Although I have implemented this, whenever I connect using User1 received powers AD I always get the ip address of the vpn pool rather a static ip address which I configured. In the output of debugging ldap 255 command I found the line "msRADIUSFramedIPAddress: value =-1062718956 ' but not any line that prove the above attribute map.

  It seems that the mapping does not work.

  All AnyConnect users get the policy settings defined internal group on ASA, including addresses form pool, dns etc server. I want User1 to get a static IP and inherit all other group policy settings.

  If someone has any ideas of how to fix this, please help.

  Thank you

  Hello

  Please give the output of the aaa server hs.

  I found the link that gives you the configuration of the requirement details.

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/configuration/guide/ref_extserver.html#wp1661694

  I hope this helps.

  Kind regards

  Anisha

  P.S.: Please mark this message as answered if you feel that your query is resolved.  Note the useful messages.

• On ethernet ESXi iface will not get the IP address of the cable modem

  I installed the Vyatta Core 6.3 virtual appliance in VMWare ESXi 4.1 U1 on a Dell Precision 490. I want Vyatta to serve as a single window for my home network together with a red interface with a public IP address, other VMS behind the DMZ and my private machines (laptops, TiVo, etc.) behind the Green interface.

  Here is my VMWare network topology:
  vSwitch0 ("green vSwitch"): NIC 0, connected to the hub of switching/wireless connection with connection cable
  vSwitch1 ("demilitarized vSwitch"): no physical NETWORK adapter
  vSwitch2 ("red vSwitch"): NIC 1, connected to the modem cable Comcast with connecting cable
  Here is my config of Vyatta VM network:
  eth0: connected to vSwitch2 ('Switch red')
  eth1: connected to vSwitch0 ("Green Switch")
  eth2: connected to vSwitch1 ("Switch demilitarized")
  Here is my config Vyatta:
  Ethernet eth0 {}
  dhcp address
  Description "red Interface.
  automatic duplex
  HW - id 00:50:56:3F:FF:01
  smp_affinity auto
  automatic speed
  }
  Ethernet eth1 {}
  address 172.16.122.1/24
  Description 'green Interface.
  automatic duplex
  HW - id 00:50:56:3F:FF:02
  smp_affinity auto
  automatic speed
  }
  Ethernet eth2 {}
  address 192.168.122.254/24
  Description "DMZ Interface.
  automatic duplex
  HW - id 00:50:56:3F:FF:03
  smp_affinity auto
  automatic speed
  }
  My Green interface is very well. All computers connected to NIC of the model Dell Precision 0 get the IP addresses assigned to them via DHCP, which I put in place for this subnet/interface.
  My DMZ interface is very well. I can assign static IP addresses to the other virtual machines, assign their interfaces to vSwitch1 ("demilitarized vSwitch"), and they can communicate with each other.
  By my firewall or zone rules, the machines on the Green interface can communicate with machines on the DMZ, very well, and DMZ machines can establish connections to the machines of the green zone, which is correct.
  Here's MY PROBLEM: eth0 can't get an IP of Comcast address. I tried to change all sorts of locations on the ethernet card virtual vSwitch, etc., nothing helped. I rolled the cable modem power, nothing helps. When I connect my modem cable back to my old wireless router, the router receives an IP address immediately. When I connect the cable modem to 1 NETWORK card on the Dell printer, Vyatta gets no IP address.
  I'm sure I'm just something wrong, but I don't know what. I have a different configuration of Vyatta identical-except-physics somewhere else, but it doesn't seem to work practically
  . I think that it has to work, otherwise why Vyatta would provide an easy to use ESXi device that's read-to-go?
  I thought that maybe the vSwitch in ESXi were getting in the way and I need to connect the virtual machine directly to the physical NETWORK card, but you can do that in ESXi, so it's obviously not.
  No idea what is the problem?

  Answer is here: http://www.vyatta.org/forum/viewtopic.php?p=133590

• I want to make a donation, but not to give my name and address

  I want to make a donation, but you askoing for my name, address, etc. I don't distribute these unless there is a direct need (deliveries, etc.). I can not just give? I have an account of Firefox and I am connected.

  Thank you

  Nick

  Try using askjoin [at]mozilla.org as indicated on the FAQ page.

  Sorry, most of us is voluntary and is not directly involved with the donation procedures.

  I imagine that, unless you use some sort of secure terminal and are present in person the number of transactions; or postal donations require the address of the cardholder for security reasons. Otherwise perhaps fraudsters could clone and use your card or change the billing address without realizing you it.

• GS728TP management of IP through DHCP address praised even if static address is configured

  I have configured the switch to use the address static IP for using a management VLAN separate VLAN 123. The web gui is accessible through this IP address.

  Unknwon reason why switch leases an IP address on VLAN 1 via DHCP management. The web gui is also accessible through this IP address.

  The two VLAN has no common membership on any port of the switch. The only cable connected to the switch is the DHCP server on the VLAN 1

  Looking at the IP configuration to the web management interface, the value of the field default gateway is the gateway of the DHCP server address, but the IP address of the switch is static.

  Software version: 6.0.1.18

  Start the verson: 2.0.0.11

  Thanks for you suggestions. I solved it in other words.

  1 change managed VLAN id 1.

  2. change port VLAN 1 and connected, because by default the bridge field was empty. Introduced the setting correct and applied.

  3 changed back to the id of the VLAN managed original

  4. problem solved.

  I couldn't change to DHCP, was an error. But he did

• Not able to keep the IP STATIC address' 'Windows '.

  Hello.. I'm not able to change the static IP address in my Windows Server 2012 Standard R2 64 bit system.

  I follow the steps below:
  1. disable the Ethernet (name of the VM network)
  2. access to the IPv4 properties;
  3. setting the following value:
  (i) use the following IP address:

  a. intellectual property:

  b. subnet Mask: 255.255.255.0
  c. default Gateway:<>
  (ii) use the following DNS server address:
  a. preferred DNS server: 127.0.0.1
  (iii) validate the output parameters: true
  4. click on Ok.
  5. click on Ok.

  After that, he tries to change the IP address. But the DHCP service is disabled; Internet no longer works and he asks that "let windows detect the settings of the system." If you click ok, the IP address is once again is changed in 192.168.2.17.

  But if I change the IP from 192.168.2.18 to 192.168.2.15, and then also in the internet stops working.

  Seuugest nicely.

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• I got an e-mail saying my installation of microsoft windows folder is up to date and he wants to give them my email address and password. is it legitimate?

  I got an email saying: my Microsoft Windows Setup file is up to date and he wants that I give him my e-mail address and password. Is it legitimate or phishing?

  Hello

  You can check the following link to learn more about how to help protect your computer "by Email and web scams."

  Scams by e-mail or web: how to protect themselves.

  http://www.Microsoft.com/security/online-privacy/phishing-scams.aspx

• assign the IP static address/user GBA 5.1

  Hello

  The ACS 4, you have the option to a user to assign a static ip address. How more easy do you solve this ACS 5?

  Thanks in advance

  / Benny

  It is possible to create defined by the user of the attribute values that can be entered as part of the definition of the user and then used in two terms of insurance and/or the values returned in authorization. This is a generic mechanism to rebut the evidence of use that you set

  This can be achieved as follows
  -Define an attribute of the identity of the IP address of type
  -Define users and enter their assigned IP address
  -Define an authorization profile that uses set it the IP address of the user record
  -Select the profile for authorization as a result in the authorization policy
  I enclose some slides illustrating this process

• Cloning of the hosts nested ESXi 5.5 in my computer 10 - address IP problem

  Hi all

  Is it possible to clone VMs host ESXi in workstation without any problem?

  If so, then when I tried to do, the cloned virtual machine always gets the same IP address as the parent VM.

  > > I tried with Bridged networking networking and host-only.

  > > Makes sure that the MAC addresses of the two virtual machines were different (unique generated)...

  Can someone help me with this please?

  Have you tried this: copy ESXi VMs - addresses management unique MAC interface?