ESXI 6.0 configuration problem: quick stats on {host} is not up-to-date

Similar Questions

• ESXi 4.1 - Dell Poweredge 2850 - tape backup - host does not support configuring passthrough

  I'm trying to get a tape backup to work on my ESXi host, so I can save my win2003 VM.  I get this error under VMDirectPath, 'host does not support configuring passthrough ".  Under Configuration > storage adapters > I don't see my tape drive listed.  Also, I noticed that my SCSI controller card is NOT on the HCL (Adaptec 39160).  See.  This is probably why passthrough doesn't work.

  So, I was thinking of buying this one (Adaptec 39320) because he seems to be on the list.  This will solve my problem or is this server too old for passthrough to work?

  To use VMDirectpath on an Intel Server chipset used must support Intel VT - d (Directed i/o).   I don't think that's the case with the models of 2850, but if it was you would see an option in the BIOS to enable this.  It is a separate option of VT - x, which allows the host run the 64-bit clients.

• 5.5u2 ESXi host will not mount CF data warehouses

  I am the admin in a test lab, so many times I have to "make do" with what I have for the material.  I recently reassigned a R910 Dell with 64 GB memory in a 5.5u2 ESXi host.  It has some storage SAS (2.5 to) and some (CT 11) directly connected FC storage and some FC HBAs for use by VMs to send data to the tape library.

  Recently, we had a power failure, and this host does not reconnect to the CF storage when she returned to the top.  (Duty to "make do" with what I means not having is not the capabilities of UPS).  I can tell the host of HBA see it properly and sees the LUNS on RAID controllers, but refuses to mount.  I go through the add storage Wizard, and he sees that there is a store of data storage VMFS, but always refuses to mount.  I also tried to remove the redirection to the two FC HBA that have been set up for this purpose, but it made no difference.

  I have now three users unable to work because they cannot access their virtual machines on storage of this FC.  I can't even transfer them off to use the SAS storage form.

  I think it might be the cause file system damage, but I'm not sure.  Someone at - it suggestions?

  Have you ever tried to set up data warehouses from the command line (see, for example, http://kb.vmware.com/kb/1011387)?

  André

• two drivers of PXI chassis with Configuration problem

  Hello

  I have two PXI chassis. One is PXI 1033 and works perfectly with the NI PXI-5404, 5105, 6509, 1409, installed 8336. The other is 1036 PXI with the PXI-5404 NI, 8366 installed. When I was trying wreath connect, as master 1033, 1036 as slave, I found several problems.

  1. in the Measurement & Automation Explorer, does not have my good guys in 1033. Instead, there is a sign of the Red Cross in bottom right with 6509, 5105, 5404.

  2. I can't find an another 5404 of the 1036. In fact, I can't find 1036 in MAX.

  Update BIOS. My PXI system is already identified under the name 'NOR PXI - 1033 Embedded MXI Express' and Chassis1 is identified as 'NOR PXI 1033'.

  So I made several tests as below:

  1. unscrew the 5404 1036 slave. MAX can configure 2 1036 chassis. Ok. But when I reconnect 5404 in 1036, same result happened as stated above.

  2 uninstall the driver of 5404, so the 5404 in 1033 does not either now. And then reboot again, same result happens again. Cannot detect the 1033 chassis. Other vouchers in 1036 don't work either.

  Please, any suggestion is highly appreciated.

  Sincerely,

  Bin

  Hi Ben,

  This happens sometimes with MXI-Express:

  Error code 12 with MXI-Express

  http://forums.NI.com/T5/PXI/two-PXI-chassis-connection-with-configuration-problem/m-p/1475876#M9033

  In general, you can read this error 12 means on Device Manager:

  Explanation of error codes generated by Device Manager in Windows XP Professional

  http://support.Microsoft.com/kb/310123

  If it was a problem of bandwidth, PCI or PXI side, you could pull a few cards to see if that alleviates the problem, or that the link from Microsoft over the States, you can disable the driver for other cards.

• Windows configuration problem on Aspire M

  If anyone on the forum has experienced the following? My Aspire M displays the following message after trying to download windows updates: "configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer.

  For about 30 minutes, the co0mputer is in this mode to 'come back' and I have to just sit there and wait that it happen by itsexercise. Most frustrating!

  This has happened for at least 8 months now and to the extent where nothing I tried helped. Windows recognizes that it is caused by a problem of Windows software, but did not come with a fix!

  I hope someone can help?

  Best regards, lachiu

  Hi GuruAid - CS and Acer supports,

  Thanks a lot to you two for your answer to my problem. The response from the Acer Support where for me first and I did not lose any time, applied the suggested steps. Support Acer mail 14/10 got to me and I waited my answer for the following reasons:

  As I mentioned in my original post, this problem has been with me for a while in which I had some Tech Guy (3) looking at my PC and the 'fixing' of the problem. Two days later he was back again. This was the case in all three fixing operations. If I didn't like my Acer Aspire so, that would have been when I was ready to buy a new computer. But, as I said, I am satisfied with the machine - it is the fastest and most powerful I got sofar and I bought my first PC in 1996 - and was reluctant to "abandon ship."

  I can an episode with Microsft. About5 weeks I contacted Microsoft technical support and has been in contact with one of their technical support people. Apparently they charge for this service and they demanded $99 for it. When they took the number and my name on my credit card down, they made a small error in the spelling of my last name. I pointed out to them, but Visa had already pulled the plug on this transaction attempt and had cancelled the card at a time. I had to get a new credit card and did not attempt to communicate with Windows again.

  I finally thought to this forum and only wish I thought of it earlier. Since 14/10 I had NO recurrence of this problem!

  After having so many false hopes, I hesitated to write after a few days the problem has been resolved. I got at least 30 starts and stops since then and there is no problem. After following the instructions Acer supports. I do, however, I keep GuruAids suggests measures on hand - just in case :-))

  So, thank you again for your excellent advice and quick help. I can't get the smile off my face :-)))

  Best regards

  lachiu

• Reference DELL 1850 and the HA agent configuration problems

  Hello

  I have a problem with DELL 1850 server while moving it to a cluster use HA. On the other DELL 2950 Server I worked well and I can move it to the cluster without problems and enable HA. I have 2 x 1850 and on two of them, I get the same following problem:

  18502.vividsky.local HA configuration

  Cannot complete the configuration of the HA agent on the host. Another HA configuration error.

  System

  VM2003 - X 64

  HA agent has an error: cmd addnode failed for

  main node: internal error of AAM - agent could

  does not start. : HA unknown error

  error

  2010-10-30 10:57:50

  Reconfigure the host HA

  18502.vividsky.local

  Administrator

  HA agent has an error: cmd addnode failed for

  secondary node: / opt/vmware/Mao/bin/ft_startup

  Cannot be completed within 3 minutes: unknown

  HA error

  error

  2010-10-30 10:21:43

  HA configuration

  18502.vividsky.local

  I made this establishment a few times using esxi in vmware workstation and used vmotion on it without any problem.

  I don't know if that is a problem because of the CPU as the 1850 uses a Pentium 4 XEON and the 2950 a Quad core (coreduo) Xeon. On the vmware workstation it worked well because I use a processor core 2 duo as well. Is this because VT? they are capable of 64-bit P4 Xeons is not VT

  in the 1850s, I have fiber connected to a SAN network cards, but I removed the warehouses of data from it as I myself suspect this could have an impact on HA configuration, but as you expected, it did not help :/

  You guys have no idea what I can do?

  Can you send me the tarred contents of the directory/var/log/vmware to host?

  The compatibility of the processor is not the problem. The two hosts are able to communicate on port groups 'management' common?

  Marc [email protected]

• Configuration problem?

  I'm new to Labview. I can't connect with 3458A. It works with 34401. I use a USB/GPIB from Agilent 82357 B interface. I have a VEE program that works with the 3458A. I think I have a driver or configuration problem. I am at a total loss, any help would be appreciated.

  I got it to work with the correct command. Thanks for your help. I have much better understand how this works now.

• "When try to turn on my computer: Windows did not start because of the following ARC firmware boot configuration problem: the ' osload partition ' parameter setting is invalid

  Original title: configuration of the CRA

  Hi, I got this message then try to turn on my computer:

  "Windows did not start because of the following ARC firmware boot configuration problem: the ' osload partition ' parameter setting is invalid. "Please check the Windows documentation about the configuration option BOW and your reference manuals of the equipment for more information.

  can someone help me?

  Hi sugenghariyono,

  ·         Did you do changes on the computer before the show?

  ·         What is the brand and model of the computer?

  ·         Are you able to boot to the desktop?

  Follow the steps in the article.

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  For reference:

  Advanced Troubleshooting for General startup problems in Windows XP

• Network Configuration problem

  Hello:

  Since last week, when I click on an icon, for example, the Page Home/Windows 7 does not come on the screen.  Instead, warning to appear at the top of the screen saying... Problem with Internet connection or Network Configuration problem.  After 5 minutes, or later, however, the screen came, but it is very slow to open web pages.

  This problem occurs most often during the night, however for the last two days, sometimes also during the day.

  Until this problem started out of blue, wireless connection with Comcast was very smooth-ride,... instantamously the homepage of popping up.

  Hints on this would be greatly appreciated.

  Thank you

  This sounds like a problem with your Comcast service. In the United Kingdom, I would suggest that you run a speed test on your connection speed. You can get no doubt do the same wherever you are. While it could be the quality of your line, the calendar offers it's the volume of traffic from when children arrive home from school until they go to bed.

  You could compare notes with other Comcast customers.

  http://forums.Comcast.NET/

  Hope this helps, Gerry Cornell

• FWSM Configuration problem

  Hello

  Please can someone help with the following problem:

  I have 659 with FWSM, I configured the FWSM in routed Mode unique.

  My requirement is to make the MSFC behind the firewall, so I need only two VLANS to act as a firewall interfaces, all other VLAN should through the MSFC.

  I used the vlan 100 as inside of VLANs and vlan 101 as Vlan outside and I did all the required configurations on the 6509 (switch, MSFC) and the firewall.

  The problem is: outside VLAN (101) is not coming on the MSFC even if there is an active port on this vlan (which is the router connected to the VLAN outside!)

  Why this vlan is not coming? Help, please

  This is the configuration I used on 6509 and FWSM (I included only the related configuration)

  ON FWSM:

  -----------------

  nameif vlan101 off security0

  nameif vlan100 inside the security100

  IP outdoor 62.149.76.2 255.255.255.248

  IP address inside 10.8.100.2 255.255.255.0

  Route outside 0.0.0.0 0.0.0.0 62.149.76.126 1

  Route inside 10.8.0.0 255.255.0.0 10.8.100.1 1

  6509 (Switch):

  --------------------

  name of vlan 100 inside set

  name of vlan 101 Set out

  define the vlan 100-101 firewall - vlan 8

  6509 (MSFC):

  -------------------------

  interface Vlan100

  Description inside of vlan

  IP 10.8.100.1 255.255.255.0

  !

  interface Vlan101

  Besides description of vlan

  IP 62.149.76.1 255.255.255.248

  ----------------------------------------------

  Yes, that's correct. This way you will get a unique link between the MSFC and FW.

  For your MSFC your default gateway will be 10.8.100.2. Inside networks for your FW, will point to 10.8.100.1, that you specified. There is no need for interface VLAN 101 of the MSFC. Keep 101 as is, otherwise.

  I hope this helps.

• Grid Configuration problem Link Datasource

  Hi Experts,

  I have 4 servers managed with cluster 1. I try to configure the data source Link grid to RAC. After you create the data source

  I click on changes in assets, but it says "An Exception occurred everything" by allowing the failover with ONS remote subscription. Later, I found that,

  When I configured the cluster as target for the data source, it says error if not, it accepts (withour any managed cluster and Server Admin).

  I don't know why it shows error. Help, please...

  Hi Joyce,
  My problem is solved. I have not assigned the name of servers managed at the analysis of the IP(RAC_related_work).one of our database administrator database
  Add the IP address of the servers managed at the RAC analysis. So this problem is solved.

  Thank you for your help.

• Configuration problem EM on 12 c OEM

  I started working on a new client, who was a repository of grid 12 c Setup program, and they have restarted a server for maintenance. When I tried to enter emctl start agent, I received the following.

  The MA Configuration problem. /U01/app/Oracle/product/11.2.0.3/dbhome_1/servername.domain.com_oem not found.

  Is there a way to create this file? is or if I should use emca, possible that I can perform a 'regeneration' without changing the initial configuration?

  Thanks everyone, I solved the problem. I made a backup of my old profiles.xml, created a void with just header and footer information, and everything started upward normally, thank you again!

• OC4J Configuration problem. $OH / OC4J_DBConsole_IPADDR_db not found.

  Hi all

  I have a new installation of Oracle 11 g 2 m4.

  I tried several times creating dbconsole, ensuring that the environment variables are defined property and also in the response file, specifically ORACLE_HOSTNAME is set correctly.

  The emca - config... returns with success,

  but in the newspaper, it shows me the URL to control db being in the form of https:// < hostname >: 5500/em

  Under OracleHome, I have a directory in the form of < hostname > dbcontrol Private

  Although my departure db control fails with above message.

  emctl start dbconsole

  "OC4J Configuration problem. $OH / OC4J_DBConsole_IPADDR_db not found. »

  My question is since emca creates the control with the format https:// < hostname >: 5500/em , and it is properly configured in OracleHome, why "emctl" refers to IPADDR and allows me not to start dbcontrol?

  Thank you

  DP

  What is the name OS & version?

  what OS command under report

  hostanme

  can you do successfully as below

  Ping

  Ping

• Photoshop CS6 configuration problem, code 16

  So I have a PC and I come again Mac Pro 2 days (it is a little difficult of is used), and my Mom took a tech shop any to download all of these programs for me. But when I tried to open Photoshop this configuration problem keeps popping up and the code is 16. I don't know how to fix it, please help! (Also if someone could elaborate on their answer that would be great, I'm really not very good with computers).

  http://helpx.Adobe.com/x-productkb/policy-pricing/configuration-error-CS5.html

• Configuration problem of the mixture of the regions with and without installation of persistence of the disc causing the JSONFormatter to fail

  I have trouble setting my local setup correctly with a mixture of regions with different configuration of persistence of disc.  Is a configuration problem on my end or a bug in GemFire and/or Spring GemFire data?

  The configuration of my work is as follows:

  < gfe: replicated-region id = "replicatedRegion" cache-ref = "gemfireCache" disk-store-ref = "overflowOnlyDiskstore" persistent = "false" >

  < gfe:eviction type = threshold "HEAP_PERCENTAGE" = "90" action = "OVERFLOW_TO_DISK" / >

  < / gfe: replicated-region >

  < gfe:local - region id = "localRegion" cache-ref = "gemfireCache" / >

  
  

  With the above configuration, I can successfully call JSONFormatter.fromJSON (json) and get a reference to a PdxInstance object.  However, when I kinda modify configuration to enable the persistence of drive on one of the regions, the call to JSONFormatter.fromJSON (json) fails.  The change is as follows:

  
  

  < gfe:local - region id = "localRegion" cache-ref = "gemfireCache" persistent = "true" disk-store-ref = "persistOverflowDiskstore"/ >

  Without any additional modification, the following error starts occurring:

  com.gemstone.gemfire.pdx.JSONFormatterException: could not parse JSON document: [Source: java.io.StringReader@5549f0e, line: column 26,: 6]

  at com.gemstone.gemfire.pdx.JSONFormatter.fromJSON(JSONFormatter.java:66)

  ...

  Caused by: com.gemstone.gemfire.pdx.PdxInitializationException: The PDX metadata must be persistent in a limb that has persisted data. See CacheFactory.setPdxPersistent.

  at com.gemstone.gemfire.pdx.internal.PeerTypeRegistration.checkAllowed(PeerTypeRegistration.java:531)

  at com.gemstone.gemfire.pdx.internal.PeerTypeRegistration.verifyConfiguration(PeerTypeRegistration.java:515)

  ...

  Note that it is breaking while I try to get a reference to a PdxInstance, and if the code has not yet arrived at the point where I place a PdxInstance object in a region.

  Thanks for any help in advance.

  Hello

  JSONFormatter PDX uses as is the serialization mechanism from the Gemfire cache. As indicators of error, you must have your persistent PDX meta-data when you use PDX with an area that itself is persistent. Adjust your configuration as follows:

  It will use a default for PDX record store, but you can also use a specific store if you wish.

  When you use PDX, a "PDXType" is created for each class serialized with PDX and this type id is stored with the data in the region. If this region is persistent, then the PDXType, associated with this object must also be kept.

  -Jens