Even if I put a null componet and remove parent... again for important to remove event listeners?

Similar Questions

• I've suddenly lost recording function - even when I put them in a new file it works for w a while then turns off!

  I've suddenly lost recording function - even when I put them in a new file it works for w a while then turns off!

  Close InDesign and relaunch it and IMMEDIATELY hold down Ctrl + Alt + Shift (Windows) or Cmd + Ctrl + Opt + shift (Mac) and answer Yes to the dialog box asking if you really want to replace the preferences.

  If you are not asked the question, you do not press the keys quickly enough!

• My internet connection is lost at home after a few minutes. I re - turn on the wifi disabled, ten and it works again for a few minutes and then repeats. It works fine everywhere else?

  Relatively new MacBook OSX El Cap 11.4

  My internet connection is lost at home after a few minutes. I stop the wifi, then turn it back on and it works again for a few minutes and then repeats. It works fine everywhere else?

  Please see recommended settings of WiFi routers and access Apple points.

  Despite these recommendations, some routers will work better with the latest Mac models if you turn the radio 2.4 GHz mode in settings and only use the 5 GHz. Note, however, that very old devices Apple and some third-party devices can then not connect at all.

  Some third party routers have advanced that you may need to change the settings:

  The encryption algorithm must be AES.

  The group key interval must be 3200.

  I can't give you specific instructions on how to change these settings, because all routers are different. Refer to the documentation for the provider.

• Advent AWP 10 still do not work even if I put in new black and white carding

  I couldn't not my working ADVENT AWP10 then bought new printer black and white and color comes from the cartages, tried to print again paper sounded like it was printing but nothing on the printer, I then cleaned the heads and calibrated the printer, tried again printed but very low took the cartages again done a test print all colors here , but not B & W can someone please help, the cartages cost me £35 not very happy just some jumps on here can help. I managed to print a small color photo colours not very good can someone please help. My son is in year 11 must print so much of course work this year. Printer less than a year old, but can not find my hope just received some on here will be able to help me.

  Hello

  1. which version of the Windows operating system is installed on the computer?

  2. When was the last time it worked?

  3 did you last modified the software on the computer?

  If you are using Windows 7, I suggest you go through the steps and check.

  Method 1:

  I suggest you to see link and run the Troubleshooter:

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  See also:

  Why can I not print?

  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print

  You can also contact ADVENT for known problems:

  http://adventprintersupport-en.custhelp.com/app/answers/list

  Hope this helps and keep us posted.

• Can I put a default title and send the message for sharing links from Adobe?

  When sharing links by e-mail, is it possible to save a custom object and the default Message?

  Not at the moment, but I asked the product team to consider adding it as a feature. Thanks for the suggestion.

• I tried EvevryThing! The "CREATED WITH ADOBE ELEMENTS 9 TRAIL VERSION FIRST" will not stop Displaying, even after I put in the serial number and Regerstered. Also the product does not show under my profile?

  I tried EvevryThing! The "CREATED WITH ADOBE ELEMENTS 9 TRAIL VERSION FIRST" will not stop Displaying, even after I put in the serial number and Regerstered. Also the product does not show under my profile?

  How can I fix it? Nothing in help or on the Site.

  Once you have registered the product, you should not see the banner of 'Trial' on NEW projects. This isn't the case, right? You only see on the project that you created before you register the product, right?

  That said, to remove the banner, go to the folder of directory on your hard drive where your project PREL files are stored and delete the folder called Adobe Premiere elements preview files.

• I have an iphone 6 it is damaged by water but I set myself and the person put it on charge and tested it with a multimeter and it worked perfectly but when I went to look for a screen tested on it, it didn't work

  I have an iphone 6 it is damaged by water but I set myself and the person put it on charge and tested it with a multimeter and it worked perfectly but when I went to get a screen tested on it because she does not have the person had not on is it did not work, even if the person has used only flow to correct and get a few corosions out with the replacement of some components of the person responsible for 10 minutes after having plugged in and the battery it wamer so it as I said her test with a multi meter test and he registered 12v and I wondered if something was wrong with it and if I could fix it easily?

  Check the liquid Indcator of Contact.

  Instructions here > liquid for iPhone or iPod is not covered by the warranty - Apple support

  Just so you know, the service of the liquid damage to an iPhone or iPod is not covered by the limited warranty of one Apple or an AppleCare Protection Plan (APP).

• Even if I put new ink cartridges in the windo continues to show low ink I can do to fix this?

  How can I change the view of low ink even though I put new cartridges in?

  Hello

  What is brand and model printer?

  Method 1: Run the fixit

  Diagnose and automatically fix the problems of the printer and printing http://support.microsoft.com/mats/printing_problems/.

   

  Method 2:

  See the following Microsoft article:

  Resources for the resolution of the printer in Windows XP problems

  http://support.microsoft.com/kb/308028.

  Method 3: Update the drivers

  a. click Start, click runand type devmgmt.msc and press enter

  b. right click on the device driver you want to update

  c. click put to update driver and follow the instructions in the wizard.

  If the problem persists I suggest you please contact the manufacturer.

   

• I put on a cd and no installation or any disk AutoPlay rises.

  I went to my computer and it said: there is no disc. I put in a disk, and nothing comes up.
  I just bought Microsoft Works 9, hoping that it works and it does not.
  I restarted my computer erase everything completely all hope it was a virus, but it still does not work.
  Help, please!

  Hello

  Step 1: Please do all the same underneath if you did some before as it is often the total process
  which solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista
  After starting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  If necessary:

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are some registry
  entries that do not fix the resolution of problems and those who "could" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys in my opinion, are those in question - for the CD/DVD drive of course subkeys as
  There will be other subkeys in these keys. Do not forget to ask involved specific keys as well as the
  Parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even registry settings correct for your CD/DVD drive
  a person with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Need advice. Is it necessary to put images in folders and subfolders with LR?

  It seems that the concept of spending hours to put the files in folders, subfolders, and sub-sub-folders is not necessary with LR. Creating all these folders takes hours, especially if you're like me and need a major reorganization of the Organization of the image. My thought is that all images can go in one massive folder as long as they are properly labeled. I can then use smart Collections LR essentially practically organize all my images. I can create a lot more sort options using smart Collections that I can by putting images in a folder. This goes against everything that I've learned about storing data on a computer, so I'm nervouse to head in this direction because it starts with unorganizing my files and remove all tags, so I can start again.

  I don't want to take it only to learn that I don't think a gotcha question. One drawback is that you are now committed to find anything using LR or tags only. What do you think?

  The folders do not exist. These are theoretical things. The operating system puts the files anywhere he wants on the disk, not even close to areas much of the time. He knows where the files because it has an indexing system.   So, if you have a c:\folder\pic.dng file and a c:\folder2\pic.dng file they are simply different names since what we call the path is really just a long file name. If you have saved the same 2 files c:\folder\pic.dng and c:\folder\pic2.dng it is again just another name of file and that's it, the same operating system and its index. The files in the same "file" will not be next to each other on the disk.   It follows that putting all your files in an important file or a series of smaller is all the same thing for the computer. If it has some significance in your mind, then put them where you want. It's of course still less difference in Lightroom, which is a database pure not concerned with the positioning of all physical, even up to what and where the storage media.  There is no limit to how many files, you can put in a 'folder', of course, despite what some think. This notion is a holdover from limitations of older operating systems and their capacity of memory addressing.  In terms of organizing files, that's what Lightroom for them and the keywords and structure should come from those and exif. Since these are incorporated into the files themselves and are pretty well standard, they will not be lost if Lightroom goes belly up. I can even read mine in several other programs that I use, so I'm not afraid of losing their organization and structure. And with daily backups of our precious files without fear of losing the LR catalogs or the other.

• How to transfer photos from my iPhone to my iPad, put them in albums and then remove them from my iPhone

  How to transfer photos from my iPhone to my iPad, put them in albums and then remove them from my iPhone

  There are several methods.

  You could make a start by looking at this article.

• How to prevent Flash blocks instantly (occurs even if I'm in Mode safe and you have disabled other plugins)?

  I tried to reinstall Firefox, install Flash again (firefox confirms that it is to this day), opening in safe mode, disabled all other plugins.

  I'm out of ideas. A few Flash crashes (sometimes firefox seems not even to recognize the accident and it is almost never to send a report) when I spent about 5 seconds in a flash object. Literally a click will make it crash.

  Is this a new problem? The reason why I ask this is that Adobe maintains a version of extended support to the Flash Player, which is 13.something. If you can not get Flash 18 working properly in Firefox, you can uninstall Flash and get this older version.

  The support of Flash article has a link to the uninstaller program.

  This page has the version of extended support (about 60% of the track and find the one for browsers based on plugin in English): https://www.adobe.com/products/flashplayer/distribution3.html

• Hi, I dropped my iphone6 in a salt water pool and was overwhelmed for only 3 to 5 seconds. I quickly ran upstairs to put it in rice and it was 2 days ago. Should I start charging or always keep rice?

  Hi, I dropped my iphone6 in a salt water pool and was overwhelmed for only 3 to 5 seconds. I quickly ran upstairs to put it in rice and it was 2 days ago. Should I start charging or always keep rice?

  Take your iPhone at the Apple Store as soon as possible. Unfortunately, warranty does not cover water damage. I'm afraid that your device is already damaged, but only professional can tell you this for sure. Take the sooner you it to the store - the best chance, it can be recovered.

• Recent update asking for permission to put on my camera and audio without my knowledge, what then?

  Recent update asking for permission to put on my camera and audio without my knowledge, what then? Does this mean that Big Brother or anyone who can turn my Audio/video and see what I do?

  Firefox will always ask permission each time before the video/audio recording is turned on - then only you can activate it.

  the authorization is used for technologies such as webrtc: https://blog.mozilla.org/blog/2013/09/17/webrtc-now-available-across-mobile-and-desktop-with-new-firefox-for-android-compatibility/

• I have a distribution list large email I want to create, BUT I don't necessarily want to put in my Contacts and all this My Contact list of people synchronized upward with my iPhone. Can I create a group without their input in my Contacts?

  I have a distribution list large email I want to create, BUT I don't necessarily want to put in my Contacts and all this My Contact list of people synchronized upward with my iPhone. Can I create a group without their input in my Contacts?

  You can create another account on your mac.

  You can open an account with mailchimp.

  There may be a limit on the number of emails you can send per day. No idea about the number, but I've heard as low as 200 per day.

  R