Exporting the problem: Please HELP

Similar Questions

• my Iphone 5 was automatically turned off, and then I couldn't go? What is the problem please help me?

  my Iphone 5 was automatically turned off, and then I couldn't go? What is the problem please help me?

  Have you tried to connect your iPhone to iTunes or the wall charger and let your iPhone for 5-10 minutes to charge its battery?

• Tecra M3 freezes up, but I can't find the problem, please help! : D

  Basically, it seems to be something of a dry joint or lose the connection under the touchpad does about the pcmcia slots. The pc works only when pressure is applied to the plastic around the touchpad. Linux seems to work better than windows in terms of freezing. So, it can load an operating system and the bar going through and it just stops, it will not go further. The capslock light stick, as will numlock. However, once you apply pressure, she continues as usual. take the pressure off and it hangs again.

  Ideas?

  Hello

  Are you sure that there is nothing wrong with the HARD drive or Windows system files?
  You suggested that Linux works better than Windows.
  So I guess that the issue could be caused by a failure of the system.

  Have you tried to format the HARD drive and reinstalling the Windows operating system again?

  I can't believe that OS gel has something to do with the loss of connection, etc.. But who knows, impossible is nothing!

  In this case, you must contact the ASP in your county because the laptop must be professionally checked and this test can be done by a user of portable ordinaries like you and me.

  So good luck

• At work, my photoshop CS6 is printing so slow, it takes up to 1 minute to produce printing. We have a printer Canon Imagepress C700. What can be the problem? Help please, anyone!

  At work, my photoshop CS6 is printing so slow, it takes up to 1 minute to produce printing. We have a printer Canon Imagepress C700. What can be the problem? Help please, anyone!

  Tells us that the problem is in the printer itself or the printer driver - because Photoshop and InDesign do not share any code to print (they don't use even the same APIs to print).

• With this new update (2.1.0.108), sync no longer works, what's the problem? Help, please!

  With this new update (2.1.0.108), sync no longer works, what's the problem? Help, please!

  Have you checked this:

  • Accident every minute or so, after an automatic update to 2.1.0.108 - Adobe database synchronization
  • https://helpx.Adobe.com/x-productkb/global/creative-cloud-crash-core-sync.html

  Concerning

  Stéphane

• I'm using Dreamweaver CC and tries to install Dw CC (2014) at the first trial, but the problem come when it expired, both my installed dreamweaver has expired, and now I just enjoy the Bill every month without the product, please help me.

  I'm using Dreamweaver CC and tries to install Dw CC (2014) at the first trial, but the problem come when it expired, both my installed dreamweaver has expired, and now I just enjoy the Bill every month without the product, please help me.

  You have more than one Adobe ID and password - for creative cloud and the other for your trial period?

  Nancy O.

• Tried to access the programs and get the error: message 16. What is the problem? Help, please!

  Tried to access the programs and get the error: message 16. What is the problem? Help, please! Photoshop, photoshop elements, Dreamweaver - none of my creative Cloud applications will be commissioning, since my last update. I need to access these programs for the job, I'm trying.

  Hi wdriver,

  It seems that for some unknown reason the authorization in the licensing folder is deleted. Please try to start one of the applications by right click and select run as administrator, it should solve the problem by doing this.

  Please let us know if it helps.

  Kind regards

  Abhijit

• ON PAPER MESSAGEDU MY C510 SAME HP IF THERE IS ENOUGH PAPER IN THE TRAY, PLEASE HELP.

  ON PAPER MESSAGEDU MY C510 SAME HP IF THERE IS ENOUGH PAPER IN THE TRAY, PLEASE HELP.

  We recommend that you reset your C510 HP first. You can perform the reset by following the steps below:

  1. press the "Power button" to activate the product.

  2. with the product, unplug the power cord from the back of the product.

  3. disconnect the power cord from the wall outlet.

  4. wait at least 15 seconds.

  5. plug the power cord into the wall jack.

  6. reconnect the power cord to the back of the product.

  7. If the product does not light by itself, press the Power button to turn it on.

  Once done, print a self-test report by following the next steps:

  1 load plain white paper in the input tray.

  2. from the home screen on the control panel of the product, click "Menu" on the upper left side. A list of menu options screens. 3. click on "Settings" and then click on 'tools '. The maintenance of the printer menu displays.

  4. in the maintenance of the printer menu, click "Printer Status Report". The product prints the report.

  If the report is printed correctly, try again to print your original document.

  If the problem persists, you may need to check the status of documents in the status bar. To do this, follow these steps:

  1. remove the stack of paper from the status bar.

  2. check that the obstacles within the status bar. A flashlight to view the mechanism inside the status bar to make sure that nothing is blocking the paper to engage with the rollers. Even small pieces of paper can cause paper feeding problems. (Important: If any obstruction is detected in the paper path, you need to refer to "Cleaning the rollers" segment at http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?spf_p.tpst=kbDocDisplay&spf_p.prp_kbDocDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c02248120-20%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken)

  3. to review the status of the paper and then replace any paper torn, dusty, curled, wrinkled, or bent.

  4. ensure that all the papers in the stack are the same size and type. Never charge which coexist types of paper in the tray. The product can only process one type of paper at a time.

  5. press on the stack of paper on a flat surface to align the edges.

  6. make sure that the paper stack does not contain less than 10 and not more than 25 sheets paper.

  (Note: the limitation of the number of documents applies only during the phase of solving problems.) Once the problem is resolved, you can load the tray to its original capacity).

  Once you have checked the status of documents, reload the tray in the following way:

  1. lift output in open position and open the door of the feeder.

  2. slide the width guide to its outermost position paper.

  3. Insert the stack of paper into the paper tray with the short edge forward and the print down side.

  4. adjust the paper width guide so that it rests against the stack of paper.

  5. lower the output tray, and then close the tray door. Once this is done, print again an automatic test report by following the above steps. If this too does not resolve the issue, refer to some more solutions at HP support center link below: http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?spf_p.tpst=kbDocDisplay&spf_p.prp_kbDocDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c02248120-20%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  GuruAid.com

• Error: "Windows cannot open help and Support." "To solve the problem, see Help and support.

  Original title: help & support

  When you try to use help and Support on the start menu, a small window opens saying "Windows cannot open help and Support." To troubleshoot the problem, see Help and support. "It's double Dutch to me. Can someone help, please?

  Hi EdwardBahr,
   
  -Remember to make changes to the computer between the calendar when things worked fine and now?
   
  Try the steps listed in the following article and check, if it helps in fixing the issue:
   
  You cannot open the help and Support Center in Windows XP
  Cannot load help and Support Windows

• error message: "no audio output device is installed" I have no sound - how to rectify the problem please?

  reinstall audio devices-error message: "no audio output device is installed" I have no sound - how to rectify the problem please? tried most of the quick fix ideas, but nothing seems to work

  Hi Jammyhorse,

  1. What is the number of brand and model of the PC?

  2. when the problem started?

  3. you remember to make changes to the computer before this problem?

  Step 1:

  You can check the following link and run the Fixit and see if helps solve the problem.

  Diagnose and automatically repair audio playback problems

  http://support.Microsoft.com/mats/NO_SOUND/

  Also check out the link:

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  Step 2:

  In the BIOS settings advanced, you can also check if the onboard sound is enabled.

  You can see the manual of the system manufacturer or contact the system manufacturer for more information on how to make the changes in the BIOS.

  Note: Change to the BIOS/complementary metal oxide semiconductor (CMOS) settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• The space bar has stopped working in text blocks. Iendupwithsentaceslikethis - I have reset the mac, but it is always the case please help!

  Iendupwithsentaceslikethis - I have reset the mac, but it is always the case please help!

  Latest version CC

  Richard

  Solved the problem - I just changed a Chinese document. I copied the milling guide in a new document.

• Hello I have a macbook pro 2011 and in a few days I had my swelling of the battery and after that I ordered a new and only for a day, it uses my new battery began to swell again, what could be the problem? Help me, I am a student that I can't do it by new

  Hello I have a macbook pro 2011 and in a few days I had my swelling of the battery and after that I ordered a new and only for a day, it uses my new battery began to swell again, what could be the problem? Help me, I am a student that I can't do it by new

  is it because of power problems?

  Take it back to the Apple Store and ask them to check it out. It should be under warranty. Bring the MBP along too. It sounds like there might be a problem with it.

• Windows95 CD-ROM - game Need for DCC Speed-No. pieces found - can not install the game - please help. ___

  Windows 95 CD-CD-ROM-game Need for DCC Speed-No. pieces found - can not install the game - please help.

  ------------------

• put an item into the basket, made an empty recycle bin, need return the item, please help, I did nothing since the drain, so the machine is in the same condition as when I emptied

  put an item into the basket, made an empty recycle bin, need return the item, please help, I did nothing since the drain, so the machine is in the same condition as when I emptied

  If you have xp, you can do system restore

• Lightroom stopped working would cut during use, update would not download through app cc, direct download installs, his record saying is corrupted to lose the battle, please help

  Lightroom has ceased to function and be cut during use, update wouldn't download through app cc, direct download, moved his record saying is corrupted, im losing the battle please help

  reset your preferences -: https://helpx.adobe.com/lightroom/help/setting-preferences-lightroom.html

  If this fails, uninstall and reinstall