Expulsion of objects based on the aging of the dimensions of time and no cache

Similar Questions

• The relay through time and Total flow control

  Hi all

  I'm relatively new to Labview and have worked on a great program from lately, which uses a Module with my cDAQ-9178 OR relay SPST 9481 to open and close the 3 different solenoids. The program should open at a specific time and leave it open until a certain amount of flow is passed through them. I already finished the programming to record the total flow through the valves, and after many hours past the forums I found a way and changes in the code that turns on the relay based on the amount of time spent searching, however it turns on the relay and leave them on until the 'period' are filled then pass on the next round. I need to change this option further so that it lights when my "Cycle Start Time" is reached, turns off when reaching the set amount of flow for this cycle and then continues to wait until the next "Cycle Start Time" occurs.

  I imagined a way to proceed would be; by eliminating where departures from the clock a new cycle each run and just have it constantly by comparing the time of "Initial start (run)" 'Start' time sequence (when I push the start sequence and actually start to opening the relay). Then change the "delay" to 'Cycle start time' and the (> =) function to a function (=). So now, it begins after the elapsed time is equal to the start time of Cycle. Certainly, this opens the questions, because currently, at the beginning of the cycle the command of the relay begins. So I need make my comparison outside the case 'Cycle' or move the control relay in the case of 'true/false '. However, then I run the question of how to get the software to change the case once he saw to stop the relay.

  As you can see, I have about 1 million different things in my head that I played with. Advice or assistance to get me on the right track, or you know of examples would be great! My code is attached below, and I'll post a photo after this post about how I'm taking care to record the total flow. Thank you for your time and help!

  Hi M_Blaylock,

  You mentioned that you are relatively new to LabVIEW. Are you familiar with some of the debugging tools?

  http://www.NI.com/getting-started/LabVIEW-Basics/debug

  Turning on climax execution should allow you to see the data flow through your schema. Also, probing the wire just before the input case structure should allow you to see what data is actually trying this case selector. If you get unexpected data, you can probe the front steps to see source these unexpected data.

  I hope this helps and good luck with your code!

• upgrade to Win7x64 and now I have my Lexmark 2470 printing problems. I reloaded the software several times and still cannot print.

  I upgraded to Win7x64 and now I have my Lexmark 2470 printing problems. I reloaded the software several times and still cannot print. Any suggestions?

  Hey! Try this link

  http://support.Lexmark.com/index?page=content&ACTP=DD_LIST&ProductCode=LEXMARK_X2470&ID=DR16510&OS=WINDOWS_7_X64&oslocale=en_US&segment=download&UserLocale=en_AU&locale=en

• Made with multi date columns to the dimension of time

  Hello world

  First let see my script:

  I have the control panel with these columns

  order_no (int),

  create_date (date),

  approve_date (date)

  close_Date (date)

  ----

  I have a time hierarchy dimension: time

  I want to see at the time of the hierarchy, how many orders created, approved and closed for each time part(year,quarter,month,..) as below:

  Date | created | approved | closed

  ————————————————------------------------

  2007-1st quarter | 50. 40         | 30

  2007 - q2 | 60. 20         | 10

  Q3-2007 | 10. 14         | 11

  2007-4th quarter | 67. 28         | 22

  Q1-2008 | 20. 13         | 8

  Q2-2008 | 55. 25         | 20

  Q3-2008 | 75. 35         | 20

  Q4-2008 | 90. 20         | 2

  …

  My solution:

  Physical layer;

  1. I create an order f alias as the fact table for the roll of the order

  2 i joined f-ordered with d-time (time alias) on f_order.created_Date = d - time.day_id

  3 - I added 2 logical column with the formula of the measures:

  Sum aggregation is_approved(If approve_date= THEN 0 else 1)

  Sum aggregation is_closed(If closed_date= THEN 0 else 1)

  order_no (will use to measure aggregation created County

  When I create the report in analytics in the generated query he used created_date and this isn't what I expected!

  What is the best solution?

  1-

  If I have to create 3 is of the order: f_order_created, f_order_approved, f_order_closed and join each other on these columns d-time?

  f_order_created.created_Date = d - time.day_id

  f_order_approved.approved_Date = d - time.day_id

  f_order_closed.closed_Date = d - time.day_id

  2-do you create my fine measure?

  Hello anonymous user,.

  The approach with three done alias that you then use in three separate sources of logical table for your logical fact is the right one. This way, you keep canonical once and did do the role play.

  So you won't need to 3 facts in the layer of logic that you ask above, but only 3 LTS. Physically, you need 3 alias joined the dimension of time with the join specifications you mention of course.

  PS: Jeff wrote about this a few years if you want to take a look.

• Graphic object based on the paragraph Style style?

  I just checked the documentation of the API and saw nothing on the point about this.

  Is it possible to write a script that applies a Style object to a jpg image based on the paragraph Style applied to this image jpg online online?

  Hello

  I did the following:

  var curDoc = app.activeDocument;
  
  app.findGrepPreferences = app.changeGrepPreferences = null;
  app.findGrepPreferences.findWhat= "~a";
  var allFounds = curDoc.findGrep();
  
  for (var i = 0; i < allFounds.length; i++) {
    var curFound = allFounds[i];
    if (curFound.allGraphics.length > 0) {
      var pStyleName = curFound.paragraphs[0].appliedParagraphStyle.name;
      if (pStyleName == "paraStyle") {
        var rect = curFound.rectangles[0];
        rect.appliedObjectStyle = curDoc.objectStyles.itemByName("myStyle");
      }
    }
  }
  

  Kai

• Determine the hierarchy of objects based on the dependency.

  Hi all
  
  All packages in the database has invalidated due to a problem. You need to find the object hierarchy in oracle.
  
  Is it possible that I can the oracle object I the hierarchically based on the dependency?
  
  Is there a metadata table that stores this information?
  
  Example: Say, there are 10 packages. Package 1 depends on package 2 and 3-based package 2 and so on... and say package 10 is not dependent on.
  
  I need the list packages in the way below.
  
  Package of 10
  Package9
  Package8
  Package8
  :
  :
  :
  Package1
  
  Please let me know if you need any details.
  
  Thanks and greetings
  Nana Akkivalli.

  Something like this:

  select * from dba_dependencies where 1=1 and name ='PKGABC' and type = 'PACKAGE BODY'
  union all
  select * from dba_dependencies where 1=1 and referenced_name ='PKGABC' and type = 'PACKAGE BODY'
  

  Also look for
  deptree_fill in the oracle documentation

  http://docs.Oracle.com/CD/A57673_01/doc/Server/doc/ADG73/CH11.htm

  See you soon,.
  Manik.

• How to hide the object based on the checkbox with FormCalc

  Hello everyone - I am very new to FormCalc and struggling to find answers in the Help menu of Adobe Pro.  The shape that I create is long and based on the requirements of option.  Therefore, if an option is not necessary (check box) more of the data fields will not be displayed for the user.

  1: I can do this?

  2nd: it's the correct script:

  If (temp. RawValue is true)

  Then(LowTempLOFF.Presence == visible)

  on the other

  LowTempLOFF.Presence = "Hidden";

  endif

  in the example above my checkbox is named "Temp".

  the object to be hidden, a numeric field is named "LowTempLOFF".

  I've also tried '1' instead of 'True', and 'on' in vain.

  To add, I want the object visible screen only - not print.

  My current error States: the "Temp.rawValue" accessor is unknown

  Appreciate any help!

  You save the dynamic PDF form? Presence changes will not work unless the form is a dynamic

  PDF.

  Paul

• Hide objects based on the menu drop-down

  Hey guys,.

  I hope someone here can help me. I've been browsing the forums and tried several options, but can't get anything to work.

  That's what I put in place:

  • Drop-down list with the following options:
    • All (value 1)
    • Specific (value 2)
    • Range (value 3)
  • Two different text boxes (a named range and the other named specific)

  What I'm trying to accomplish:

  Based on the drop-down menu, the boxes must be visible or hidden:

  • All (value 1). the two boxes are hidden
  • Specific (value 2); the specific box is visible, but the beach area is hidden
  • Range (value 3); the beach area is visible, but the specific box is hidden

  No matter what I try (JavaScript and FormCalc) I can't get this to work. If I start with hidden text areas they appear not visible, and when they begin to visible, they hide. I'm pulling my hair out on this one. Any help would be greatly appreciated.

  The error isn't in your code, it's in the form itself...

  In LiveCycle Designer, you have the properties of form that will design the PDF on how he'll react

  You form is set to be a static PDF and a large number of features are disabled in static PDF files

  To change your static to the dynamicform, follow the instructions:

  1. in LiveCycle, open your PDF form

  2. click on Files > in the form

  3. open the default values tab and change the last static dynamic dropdownlist (this option may not be necessary as it is for the side server only, but change still)

  4. open the overview tab and change ' Preview Adobe XML Form as ' of 'static PDF form' to 'shape dynamic XML'

  I hope that this will help there!

• Buckets of the interaction between the physical i/o and buffer cache hach

  I read the book Expert Oracle practices on issues of lock contention. While I was reading this chapter. I'm little bit confused the bahavior of the buffer cache when physical i/o occurs. According to Tom Kyte, when data blocks are read on disk (if missed cache) the following steps occurred. Ask Tom & amp; quot; How to work the Database Buffer Cache? & amp; quot;

  (a) access to the buffer cache and search for block

  (b) if the block isn't here, perform physical i/o and put it in the cache

  (c) return the block of memory cache

  However, I wonder what stage b has occurred which means put the data block in the buffer cache. For this, the data block is added to the associated buffer cache hash buckets?

  As far as I know, in order to cache data hit intended address of applicable block in buffer cache hash bucket. The hash function is generated during this data block address. (if acquired the lock of the child) And then find the address of the data block in the cache buffer chain to locate the block of buffer in the buffer cache.

  My second question is what stage an occur (go to the buffer cache and search block) how to block oracle look? I mean where did he look like? My third question relates to my second question, Oracle if discovered that the block in the buffer cache, does know where to find them? I guess that Oracle does not know where to locate it in the buffer cache. Therefore, it uses cache buffer hash buckets. I'm wrong?

  Last question is, I'm just trying to understand how buffer cache buffers are linked, buffer cache buffer hash, how it works?

  Thanks in advance.

  > What happens if planned lines resident for other blocks of data in the table? How can you join the other data block addresses? And, how do you know that lines which are located in what block of data?

  See this demo:

  Microsoft Windows XP [Version 5.1.2600]

  Copyright (C) 1985-2001 Microsoft Corp.

  C:\Documents and Settings\Administrateur > sqlplus scott/tiger

  SQL * more: Production release 11.2.0.1.0 Wed Dec 18 09:01:50 2013

  Copyright (c) 1982, 2010, Oracle.  All rights reserved.

  Connected to:

  Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - Production

  With partitioning, OLAP, Data Mining and Real Application Testing options

  SQL > drop table test is serving;

  Deleted table.

  SQL > create table test in select * from object;

  Table created.

  SQL > set line 200.

  SQL > column nom_segment for a20;

  SQL > select nom_segment, segment_type, header_file, header_block dba_segments where nom_segment like 'TEST '.

  NOM_SEGMENT SEGMENT_TYPE HEADER_FILE, HEADER_BLOCK

  -------------------- ------------------ ----------- ------------

  4 1218 TEST TABLE

  Average for test table header block are 1218 that resides in file number 4.

  SQL > SELECT

  2 dbms_rowid.rowid_relative_fno (rowid) REL_FNO,

  3 dbms_rowid.rowid_block_number (rowid) BLOCKNO

  4 test where object_name = 'EMP ';

  REL_FNO BLOCKNO

  ---------- ----------

  4 2443

  SQL > variable s/n varchar2 (30)

  SQL > exec: s/n: = dbms_utility.make_data_block_address (4, 2443);

  PL/SQL procedure successfully completed.

  SQL > print s/n

  S/N

  --------------------------------

  16779659

  SQL > SELECT

  2 dbms_rowid.rowid_relative_fno (rowid) REL_FNO,

  3 dbms_rowid.rowid_block_number (rowid) BLOCKNO

  4 test where object_name = 'I_AUDIT ';

  REL_FNO BLOCKNO

  ---------- ----------

  4 1223

  SQL > exec: s/n: = dbms_utility.make_data_block_address (4, 1223);

  PL/SQL procedure successfully completed.

  SQL > print s/n

  S/N

  --------------------------------

  16778439

  SQL >

  Then, I got two dBA for different lines that are in the block No. 2443 and 1223.

  Concerning

  Girish Sharma

• Re my Acer XP: How can I tell if I have installed Firefox 4? I went through the motions three times and have not been told that I managed. When I look at "About Firefox" tells me that I still have version 3.6. What gives

  That's about all. If you would like more information I'll need some advice from you, such as specific questions. Thank you.

  Follow these steps.

  1. Go to Download Firefox 4.0.1 and download the installer to your desktop.
  2. Then go to add/remove programs, scroll down to "Mozilla Firefox" and delete it, choosing to keep your bookmarks, customizations, etc. (don't tick the box).
  3. Reboot and delete the folder called "Mozilla Firefox" at this location: C:\Program Files\Mozilla Firefox
  4. Finally, run the installation file downloaded previously on the desktop.

  Your bookmarks, etc., customizations are stored in a different location and will become available to you even once you complete the installation.

  After completing the installation, go to the Plugins check page and update if necessary.

• The disk of light and SDS Cache activity

  I have a relatively new W530 with the installed at the factory 16GB drive HARD drive cache and the ExpressCache software (working properly according to the Lenovo-recommended test). I want to know if the drive activity light shows HD activity only or also SDS hides.

  My observation is that for a long time the drive activity light is on permanently. The first time that this has happened, the warranty support told me that the HD failed and sent me a new. (They don't seem to know anything on the internal tables of health HD I thought existed and could be interrogated with a special software). Anyway, this seemed to solve the problem for a few months, but it is recurring lately.

  Looking again at the Task Manager/Performance tab/Resource Monitor tab / Disk, I can see that the larger disk of the user's ExpressCache service (as it was the first time). I stopped this service and set it to manual, and the constant activity stopped shortly after. He has not re-emerged in the last hour or two. Although the light is off now (for the most part), I still don't really know what that means; the first question remains...

  No matter what light you can pour on the light function (no pun intended) disk activity would be appreciated! -JCW2

  
  

• BlackBerry App that enables other applications on the device according to the events of time and/or location

  To create an ABC App that performs the following operations - are the points below as possible for the Blackberry OS 6 and 7?  Yes/No :-) - and whether links to the code samples.

  (0) is still active (though in the background, possible?), while in the background, it will be as described in (2), (3), (4) and (5) below.

  (1) see the other apps on the phone (what kind of applications are possible?)?   The following points (2) and (3) are mainly possible if (1) is possible.

  (2) can activate the apps and activities seen in (1)? (depending on the configuration of the user in ABC app)

  The applications can be started with the entry of parameter?

  (3) sends messages for background apps on the phone (from ABC app, depending on the configuration of the user in ABC app), who are running in the background.  (3A) is the model of Blackberry Sandbox allow applications to share data (files)?

  (4) you can make (2) and (3) above according to tell of a weather event

  (5) following the location of users (if the user allows) and designated operational entities (2) and (3) if the user reaches or crosses a specific location.

  Thank you

  Paul

  You can run (yet) background apps, although there was much demand for such a feature and most valid use cases provided. I can't imagine that this is not in the pipeline.

  You can not (yet) start other applications or communicate with them, but who was announced for BB10 and is called "invocation framework". At best, the details are still sketchy.

• How to get 2 xml (brother) of the tag even time and merge them

  How to get 2 xml(Sibling tag) content at the same time and merge them and find the value of the result in the indesign file with page number

  As

  account <>

  < a > This is a text < /A >

  a-123 < B > < /B >

  < / documents >

  First of all, we need to tag A and B value as:

  It is a text - a-123 and then get this form of text from indesign doc page number

  Help, please

  Try this,

  var root = app.activeDocument.xmlElements[0];
  var aTag = root.evaluateXPathExpression("//Record/A");
  var bTag = root.evaluateXPathExpression("//Record/B");
  for(i=0; i
  Vandy
  		   

• Best practical Question - update the query (see object) based on the drop-down list selection

  I have a question about the most efficient way to perform the following task:

  I create a page that contains several DVT components to display data based on specific requests.  Top of page I am hoping to have a drop down menu (selectOneChoice) that contains dates different and based on what the user selects (i.e. 2010, 2011, 2012, 2013, etc.), this will update the query in the view object of some (i.s. WHERE Date = '2011', or WHERE Date = 2013"), and then you view the appropriate data in the DVT.  What is the best way to do this - from a point of view bean managed / page, as well as the View object?  Advice/documentation would be appreciated.

  Thank you!

  When you drag the vo executeWithParams one another that will create links for operations such as 'executeWithParams2', 'executeWithParams3 '. On the method that you use to update a view by calling the executeWithParams operation, you call the other operations too.

  Timo

• Create the object based on the Instance of TestStand

  Hello

  I currently have TestStand code that creates an ActiveX to a StationGlobal object reference...

  Currently, the created ActiveX object reference is always the same... I am looking for a way to create a different ActiveX object reference depending on which instance of TestStand open...

  So I guess I'm wondering if there is an easy way to do this? Is there a variable that I could use to distinguish the various teststand and somehow that integrate Options create?

  Thanks for any response.

  I can imagine that this Engine class property can help you: