External Interface problem

Similar Questions

• Problem adding external interface CSA to 6 IPS

  I have configured my AIP - SSM sensor run 6 FPS to connect to the CSA MC, but I have a connection failure. The sensor shows the following error message when you try to connect:

  evError: eventId gravity = 1168311248090659938 = WARNING = Cisco vendor

  Author:

  hostId: os - ips

  appName: externalProductInterface

  appInstanceId: 317

  time: 2007-01-20 02:50:22 2007/01/19 20:50:22 GMT - 06:00

  errorMessage: name = errNotAvailable failure opening a subscription on the Management Center for the external interface of Cisco security to 1.1.1.1: response analysis found a different element when waiting for the SOAP Envelope element

  If your™ is version 5.0 so can you please set the url/csamc50/CETS-server and try again after activation of the interface.

  THX

  Madhu

• Change the IP address of the external Interface

  I need to change the IP address of the external interface remotely.  I have SSH in to the ASA plan and make a change.  I can't be there to make this change, since the site is out of State.  There will be problems?  The current configuration is

  interface Ethernet0/0
  nameif outside
  security-level 0
  IP 66.102.7.22 255.255.255.248

  The new IP address will be 66.102.7.18 255.255.255.248.  Also, is this the right syntax?

  interface Ethernet 0/0

  no address ip 66.102.7.22 255.255.255.248

  IP 66.102.7.18 255.255.255.248

  Thank you.

  Diane

  Diane,

  If you access the ASA via its public IP address on the external interface, and if you change this IP address, you will lose communication with the ASA.

  It's better if you can make the change from the inside.

  If you need to change remotely, you can change the IP address, and then try the SSH connection to the new IP address.

  However if a problem occurs, you cannot access the ASA.

  The syntax is correct.

  Federico.

• VPN; list of access on the external interface allowing encrypted traffic

  Hi, I have a question about the access list on the external interface of a router 836. We have several routers on our clients site, some are lan2lan, some are client2router vpn.

  My question is; Why should I explicitly put the ip addresses of the client vpn or tunnel lan to the access list. Because the encrypted traffic to already allowing ESPs & isakmp.

  The access list is set to the outgoing interface with: ip access-group 102 to

  Note access-list 102 incoming Internet via ATM0.1

  Note access-list 102 permit IP VPN range

  access-list 102 permit ip 192.123.32.0 0.0.0.255 192.123.33.0 0.0.0.255

  access-list 102 permit ip 14.1.1.0 0.0.0.255 any

  access-list 102 permit esp a whole

  Note access-list 102 Open VPN Ports and other

  access-list 102 permit udp any host x.x.x.x eq isakmp newspaper

  I have to explicitly allow 192.123.32.0 (range of lan on the other side) & 14.1.1.0 (range of vpn client) because if I'm not I won't be able to reach the network.

  The vpn connection is not the problem, all traffic going through it.

  As far as I know, allowing ESPs & isakmp should be sufficient.

  Can anyone clarify this for me please?

  TNX

  Sebastian

  This has been previously answered on this forum. See http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40.ee9f970/0#selected_message for more details.

• Multiple Crypto cards on simple external Interface

  Hi, I got the following encryption card configured on my ASA5505 to allow Cisco IPSec VPN clients to connect from the outside:

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  I'm now trying to set up a map of additional encryption - a static configuration to establish a tunnel with Windows Azure services. The configuration, they gave me is:

  Crypto map Azur-crypto-map 10 correspondence address azure-vpn-acl

  crypto azure-crypto-card card game 10 peers XXX.XXX.XXX.XXX (hidden)
  

  card crypto azure-crypto-map 10 set transform-set of Azur-ipsec-proposal-set

  Azur-crypto-card interface card crypto outside

  However, when I apply this configuration, my Cisco IPSec clients can connect is no longer. I think that my problem is that last line:

  Azur-crypto-card interface card crypto outside

  that blows away my original line:

  outside_map interface card crypto outside

  It seems that I'm stuck with just picking one of the maps to apply to the external interface. Is there a way to apply both of these cards to the external interface to allow the two IPSec tunnels to create? We lack ASA version 8.4 (7) 3.

  Hello

  You can use the same "crypto map"

  Just add

  card crypto outside_map 10 correspondence address azure-vpn-acl

  crypto outside_map 10 card game peers XXX.XXX.XXX.XXX (hidden)
  

  card crypto outside_map 10 set transform-set of Azur-ipsec-proposal-set

  Your dynamic VPN Clients will continue to work very well that their statements "crypto map" are in the order of precedence / low in "crypto map" configurations (65535) and VPN L2L is higher (10)

  And I want to say with the above is that, where a connection VPN L2L is formed from the remote end it will be naturally VPN L2L configurations you have with the number of configurations "crypto map" '10'. Then when a VPN Client connects it naturally will not match the specific configurations of the number "10" and will move to the next entry and the match (65535)

  If you happen to set up a new connection VPN L2L then you might give him the number "11" for example and it would still be fine.

  Hope this helps

  -Jouni

• OnLoad ActionScript external interface

  Hello

  I have this external interface code that sends a url of the video to a video player when a user clicks on a button, it goes something like this:

  < script language = "JavaScript" type = "text/javascript" >
  {$(document) .ready (function ()}
  function callJavascript (sendText) {}

  window.document.myMovie.SetVariable ("testValue", Mathias);
  }

  });
  < /script >

  The code above works well when a user clicks a button with onclick the variable passed is a url of the video

  and is sent to the player.

  The problem is I want to get the video url passed when the page is loaded.

  I tried.

  < script language = "JavaScript" type = "text/javascript" >

  {$(document) .ready (function ()}

  var sendText=$("Videosroll/Videos/1.flv").val ();

  window.document.myMovie.SetVariable ("testValue", Mathias);

  }

  < /script >

  It does not work. I think that its because the videoplayer is not fully charged when this action is invoked.

  I looked at javascript timers etc. If anyone has a solution please help.

  the actionscript code calls the callnow function.   There is no need of this onload = "callnow ()". "

  Copy and paste the actionscript code that you use.  If it is copied and pasted, you typo you import statement that needs to be fixed.

• External Interface class causes JavaScript error in Internet Explorer

  I'd appreciate any help with this: I need to pass the info of the URL of my pages in my film. But when I use the external Interface in AS2 class, Internet Explorer displays the page OK and directed the film, but it does not have the JavaScript function I call you and gives me an error of yellow triangle of "flash is not defined" in line 1.
  
  I tried the publication of version 8 and version 9 player. And there is no error in Firefox, which runs my JavaScript code and HAVE it all just great. (Yes, big surprise.) The AS code is quite simple...

  Holy Batman tracks, you're a God indeed! Flash has been automatically creates the Object and Embed tags when you publish the swf file. But I noticed in your article, when you discussed what punctuation marks were acceptable for the ID, oblique were not among them.

  Since the movie is leftmenu.swf and is located in the flash subdirectory, the name and ID that was flash/leftmenu. After mucking, I found that the problem was in the AC_FL_RunContent function (also automatically created when the movie is published). When I changed the 'id' attribute it simply be leftmenu, IE and Firefox have both pleased, and I didn't have to make any other change. Go figure.

  Thank you!

• Static and VPN on the external interface

  Hello

  Can someone tell me if it is possible (and if so, how) do vpn enabled on the external interface and to have something like:

  public static x.x.x.x interface (indoor, outdoor)

  IE: I have two addresses ip - one for the router an e0 on the pix. I create a static and lists of access to allow inbound http/https server inside but I also want to allow vpn hit e0 and work. My configs work if I use an ip address 3 for the static, but not if they share. I can imagine that the static method takes the vpn traffic before the pix can use it OR maybe as the pix has no route to the now (due to the static method) that it cannot answer?

  Hope I'm making sense

  Thanks for the time spent on this

  see you soon

  Andy

  I think you want something like this:

  public static tcp (indoor, outdoor) interface http 10.10.10.10 http netmask 255.255.255.255 0 0 (where 10.10.10.10 is your web server)

  public static tcp (indoor, outdoor) interface https 10.10.10.10 https netmask 255.255.255.255 0 0

  access-list 101 permit tcp any host x.x.x.x eq 80 (where x.x.x.x is your IP interface)

  access-list 101 permit tcp any host x.x.x.x eq 443

  Access-group 101 in external interface

  It will be useful.

  Steve

• Access ASDM ASA on the external Interface

  We have three ASA5510s, each configured for ssh and http access to the Cel outside.  One of them has aaa users/passwords defined for both ssh and http.  I can access the ASA configured for aaa of the designated host allowed in the external interface normally using credentials of the aaa.  When I try to access one of the other two, they will refuse the enable login password.  The configured aaa ASA is version 8.2 with ASDM 6.21.  The other two are the two ASA version 7.0 with ASDM 5.07.  The ASA requires aaa is configured for https access?  How can I make these other two accept the ASDM login?  Thank you!

  If you do not have aaa then configured for ASSISTANT Deputy Ministers, you must use empty username and password enable.

  Also, you can use the "aaa authenticate http LOCAL console" and use a user/pwd to a private 15 user name to connect to the ASDM.

  To resolve what is a failure you can activate "debug http" and "debug aaa" on the SAA to see the reasons for which the user is rejected.

  I hope it helps.

  PK

• Can't ssh on pix from the external interface

  I am using s/w ver 7.0 (4).

  The config for ssh is:

  generate crypto module rsa keys 1024

  WR mem

  SSH a.b.c.d 255.255.255.255 outside

  but it does not work.

  Help, please

  Yes, if your external interface is mapped to y.y.y.y, then you will be not able to ssh to x.x.x.x as it will be pass on to y.y.y.y.

  You can change the static 1 to 1 to the port for each particular port address translation you need sent to y.y.y.y.

  Please evaluate the useful messages.

• SSH to the external interface

  How to configure ssh on the external interface of the asa? I have defined an applied, external interface access list, but it did not work for some reason any

  Here is a list of access

  interface GigabitEthernet0/1

  nameif outside

  security-level 0

  IP 10.254.17.9 255.255.255.248

  !

  interface GigabitEthernet0/2

  No nameif

  security-level 100

  no ip address

  !

  interface GigabitEthernet0/3

  EIGRP 2008 description

  nameif eigrp

  security-level 100

  IP 10.40.50.65 255.255.255.252

  !

  interface Management0/0

  nameif management

  security-level 100

  IP 192.168.251.1 255.255.255.0

  management only

  !

  boot system Disk0: / asa821 - k8.bin

  passive FTP mode

  access-list 110 scope ip allow a whole

  NAT allowed ip extended access list a whole

  allow_ping list extended access permit icmp any any echo response

  allow_ping list extended access permit icmp any any source-quench

  allow_ping list extended access allow all unreachable icmp

  allow_ping list extended access permit icmp any one time exceed

  allow_ping list extended access udp allowed any any eq isakmp

  allow_ping list extended access allow esp a whole

  allow_ping ah allowed extended access list a whole

  allow_ping list extended access will permit a full

  allow_ping list extended access permit tcp any any eq ssh

  access-list extended ip allowed any one sheep

  icmp_inside list extended access permit icmp any one

  icmp_inside of access allowed any ip an extended list

  pager lines 24

  asdm of logging of information

  Outside 1500 MTU

  EIGRP MTU 1500

  management of MTU 1500

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow all outside

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  Access-group allow_ping in interface outside

  Can't say I've seen this before, but SSH is easy to do on the SAA.

  I recommend you to take out the first interface access list to see if that would be it.

  You have published only a partial section of the config, but make sure you have the SSH command with the address of the subnet that you connect from. Your config is no longer visible as I type this but try "SSH 0.0.0.0 0.0.0.0 outdoors. This allows all subnets access to the external interface. This command works as an access list to restrict connectivity to approved subnets. i.e. ' SSH 10.0.0.0 255.0.0.0 out "only allow hosts on the 10.x.x.x network to connect via SSH.

  Turn 'debug ssh' to see what errors are too.

  And, you can always remove your keys (related encryption rsa key) and rebuild their return (encryption key generate rsa 1024 mod gen). This will make your ssh client, I use PuTTY, think that this is a new feature and invites the OK to connect.

  Good luck.

  Kevin

• Secondary public network on the external interface

  We already have a range of public address configured on the external interface (213.XX. YY. ZZ/29). Our supplier we've assigned a new range of public addresses (62.XX. YY. ZZ/29).

  How can I configure this on the PIX?

  PS: as far as I know, the secondary addresses are not possible!

  Hello

  You don't need to configure anything on the PIX make you just as your ISP routes the new addresses to your PIX - then you can use the new address to what you like.

  Concerning

  Kim

• How to get the time limit requested when ping external interface FW IOS?

  After I install CBAC on an IOS Firewall Router and deny all incoming ICMP request, I ping the external interface of the router and I get "response from the (the external interface IP): the unreachable destination network. I think it's quite risky because my IP from the router's external interface is known. How can I set up such that I can get "Timeout asked" instead?

  Hello

  Try not to implement the "unreachable no ip" of your external interface.

  This command prevents the router ICMP unreachable sending at all.

• WebVPN - no external interface connectivity

  Hello

  I have configured WebVPN on a router 1811W running IOS 12.4 (11) XW5, and even if the gateway is located directly on an external interface, port 443 seems filtered to the clients that connect through this interface (inside the interface, the traffic is allowed). What can I do to force the router to listen for incoming connections on the external interface (as it is supposed to)? I have no firewall or ACL that can potentially interfere with the VPN.

  Thank you!

  It comes to you main road

  IP route 0.0.0.0 0.0.0.0 FastEthernet0 10 track 123

  You backup route

  IP route 0.0.0.0 0.0.0.0 Dialer0 20 track 124

  If you try Dialer0 access from the outside, you return traffic passes through FastEthernet0.

  You have to 'Local ACB' for the correction...

• VPN client and ssh to the external interface of the ASA

  Hello world

  I was testing clientless ssl in my lab at home.

  When you're connected via vpn without customer, I am able to ssh ASA outside interface, but when I use ssl vpn only I can't ssh to the external interface of the ASA.

  Need to figure out how I can ssh to the external interface of the ASA using clientless ssl vpn?

  Concerning

  MAhesh

  Mahesh,

  When you are on clientless SSL VPN to your customer is not limited routes of the Internet, isn't being NATted etc. If ASA is set to allow ssh from outside, then the VPN SSL without client user is no different from any other.

  A the user SSL VPN full tunnel can have any or all of these factors at play. One of them can cause the impossibility to access the ASA outside interface via ssh. I see the configuration to tell you which one (or more) is to blame.