Failure of the wireless connection on computer laptop error
Wireless will not start (was of course very well yesterday)
Checked all the other computers are beautiful - and network is in place.
Computer HP laptop under Vista SP2 about 5 years, seeing RED was case indicating any wireless connection.
Found this file and an error code:
Network adapter teredo tunneling pseudo interface does not start code 10
do I need an updated driver?
Currently have tunmp.sys version 6.0.6001.18000 checked Microsoft site, did not. Could be part of a service pack?
Have not tried a rigid cable connection yet, but would not be the wireless card works, but could allows me to download a driver if that is the question.
Or is the card fried for a reason, and this is the advice that I received from the system.
Hello
If it is only the appearance of the motherboard wireless card, you can try to borrow from a friend, a PCMCIA card or a USB Wireless Card, install.
Perhaps you'd be happy and a sub $20 USB card will solve the problem.
Be careful before paying nearly 300 to fix.
A laptop 5 years when you work can be bought for about $150 - $180.
Good luck.
Jack, MVP-Networking. EZLAN.NET
Tags: Windows
Similar Questions
-
where to find the switch for wireless connection on computer laptop esprimoV5535
get the message {connection Wi - Fi doesn't work}, but it is not no matter what visible switch on laptop so presumably its located
via the keyboard
Hello
· If it works much earlier?
Through my research, I think it's the F1 key, you need to press on and press and hold the FN key (lower-left beside Ctrl) at the same time. This should illuminate the LED on the front of the computer laptop-extreme right wireless.
You can view the documentation for the laptop to switch wireless for more information.
For any other help, I suggest you to contact your laptop manufacturer support.
Here is the link: http://support.ts.fujitsu.com/Download/Index.asp?lng=COM&Level1=&LNID=44
I hope this helps.
-
I'm tryng to connect wirelessly between my laptop and printer but I am unable to do so.
My laptop finds the printer and when I go to add the device I invite me to "Enter the WPS PIN code for your printer". So, I printed out the Configuration Page of the network and it gives me the "wi - fi direct password", which I suppose is the password that is required to establish that it connection (I may be wrong in my explanation). However, when I type the password on my laptop it does not establish the connection. I said "try to add the printer again, or check with the manufacturer for addiitonal installation instructions.
Any insght and assistance is greatly appreciated.
Thank you.
Hello
You should searh for your wifi network at home and connect your printer and the laptop to the network. Direct WiFi option is really only for configurations that do not have a modem/router.
You may need to disable the option Wireless directly on your printer to help the wireless configuration.
-
Blue light on my printer is blinking and laptop unable to connect to print
Hello
Thank you for using the HP forum. You can try the following:
Please download and run the HP Print and Scan Doctor (PSDR) tool to diagnose and solve your problem
http://h20180.www2.HP.com/apps/NAV?h_pagetype=s-926 & h_lang = on & h_client = s-h-E016-1 & h_keyword = DG - PDU
Hope that helps. -
connection Wi - Fi
My computer connects to the wireless internet, but I am still unable to connect to internet even though it is always connected to the wireless connection. How can I solve this problem and what could be the problem?Hello
1 did you change your computer, after which the issue started?
2. during how long have you had the problem?
3. what web browser do you use?I recommend to update your network card drivers and check if that helps.
http://support.Microsoft.com/kb/283658Let us know the status of the issue and also please answer these questions.
-
Repairs on the wireless connection
I have a Dell dimension and we have wireless broadband via a router. In this computer, the connection with the browser keeps turn off even if the wireless connection says "excellent". We must repair the connection to the internet to relive. We use Windows XP Pro SP3. This problem will not occur with any other laptop or computer in the House.
Hi Tinker7,
Method 1
This problem may occur if theenable IEEE 802. 1 X authentication for this network check box is selected. If this box is checked, but there is no server to authenticate the connection is interrupted. If you turn on the wireless network connection, it disconnects again after a short period.
Computer disconnects from a wireless network after random time intervals in Windows XP
http://support.Microsoft.com/kb/910387
Method 2
If the previous step fails then I suggest that you update the wireless desktop network card driver from the card manufacturer's website.
Information about the hardware devices for Windows XP drivers
http://support.Microsoft.com/kb/319908
I hope this helps!
Halima S - Microsoft technical support.
Visit our Microsoft answers feedback Forum and let us know what you think.
-
Failure of the USB2 connections
I have a Hitachi 250 GB hard drive and a keyboard wireless mouse. I had to move connections USB2 from the monitor to the computer case due to the failure of the USB2 connections on the monitor. The keyboard and mouse don't work, but the hard drive is not detected in windows Explorer. It is detectable by using Device Manager where it says the device is working correctly, but I can't access it. Good thing, I don't have a lot of hair out.
In the device under Bus USB locate controllers your hard disk manager, right click-> Uninstall, then restart your computer.
Or
Try it on a different computer if the symptoms are the same, it could be a bad cable, try a different cable or it could be a faulty hard drive enclosure. -
Wireless connection unavailable on laptop, but shows all ok on pc and router
I was at Midway through a conversation today on msn when my wireless connection (on my laptop) disappeared. I checked my pc and everything seems ok, here, my netgear router shows that everything is fine. When I click on 'Find a wireless network' his party! I can access the net very well by plugging it but as soon as I go wireless, I still lost.
Tried to connect manually - says network with that name already there
Tried to re start all
All cables checkedIt's a laptop Toshiba L300
Virgin cable broadband
Router NETGEAR Wirelesseverything works fine as long as I'm using the cables.
I only had my laptop and router wireless for a month.
Please any other ideas what to do, I really need to be wireless for work as soon as possible
Hello severina_falls,
Thanks for posting on the Microsoft answers Community Forum.
I have some suggestions for you to see if we can provide you with your wireless connection.
(1) check that the WiFi switch is on on the front panel of your laptop. It is a quick check
(2) Recycle the router wireless on and outside. Wait at least one minute, then turn it back on. Retest with your wireless network.
(3) are getting you the error messages in the case where connects to deal with your wireless connection?
To join the event logs: click on the Start button, right-click computer, click on manage.
If you receive a notification of user account control , simply click on continue.
Double-click Event Viewer. Study summary of the the event logs for errors dealing with wireless.
(4) use System Restore to get your iIf wireless upward and running, you have a System Restore Point that was before starting the problem with your wireless network.
Use the following KB to get the procedure on the system restore.
936212 KB - how to repair the operating system and how to restore the configuration of the operating system to an earlier point in time in Windows Vista
http://support.Microsoft.com/kb/936212If please post again and let us know if it helped to solve your problem or if you need further assistance.
Sincerely, Marilyn
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think. -
Inspiron N5110 loses the wireless connection
My Inspiron N5110 loses the wireless connection frequently. We have many other devices in the House - laptops, iPhones, etc. - who continue to operate perfectly through the router even when I lose my connection. The store usually brings me to reset the router, even if, as I have indicated, the router works properly. Any thoughts? Thank you!
Richard.Kelly,
The Intel Centrino Wireless - N 1030 adapter works ONLY on 2.4 GHz
How to connect to your wireless router I use these settings to the recommended wireless router I use channel 11. I have a new SSID to connect easier.
You can also try these settings...
Go to the drivers & downloads , enter your service tag, and then select your operating system. Under network, download and install the latest drivers.
Try these tweaks...
Start, Control Panel, Manager of devices. Click Network and then right click on your wireless network adapter, on the left, click on properties, power management. Uncheck the allow the computer to turn off this device to save power.
Go to the options power and changed the wireless adapter setting, adjustment of maximum power for maximum performance.
Rick
-
HP DV7t-6100 loses the wireless connection
My HP DV7t regularly loses its wireless connection, without a valid reason, since I bought it a year ago. The remedy was to reset my router, despite the fact that no other devices at home - not even an another HP laptop and an HP printer - loses connection. But lately when I put the laptop to sleep - usually by closing the lid - the computer completely forget what network is attached to and so I have to reconnect manually each time. Even then, it takes very, very long time to connect and sometimes even said "it takes longer than expected to connect to the network.". Happy, told me what I already know! I checked all my settings in Windows 7 "Network and sharing Center" to make sure that my network is selected, it is a home network, that "automatically connect"; is selected, and that all my data password is correct. He still refuses to recognize the network and connect automatically. I'm done with this and just can't understand why this is happening. I haven't changed anything in my computer or router configuration, so I am at a loss why the system forgets everything and must be connected manually. The wireless in my computer module is an Intel WiFi Link 1000 BGN and all drivers are up to date.
None of the suggestions so far have worked, but it seems to me a solution: spend my router from WEP to WPA2 encryption seems to have solved the problem, at least for now. I have no idea why this works, but a bit of google searching seems to indicate that wireless WEP can be flaky with cards and routers. If it doesn't work anymore, I will be sure to repost for a solution. Thank you all for the help - it takes a village (so to speak).
UPDATE: after 24 hours, the connection through WPA2 is rock stable with no connection dropped. It is also faster to download. I hope that this solution works for others.
-
Re: Satellite L670 loses the wireless connection
Hello
I have a Satellite L670 - 1 H 1, a new laptop that runs Windows 7, with all the drivers and software uptodate, including the wireless card.
I have a BT Home Hub 3 with an Edimax EW 7416APN v2 300 m range extender to help boost the signal in the kitchen area.
The laptop works fine when I stay in the room where the reception centre. If I move in the kitchen the laptop will usually lose the wireless connection after a few minutes and I cannot get it back unless I turn the LAPTOP works and return to the Home Hub.
I see no obvious reason to this problem. Two other laptop computers used in the home, more a smartphone stay connected with full signal in every corner of the House, at any time.
I have to use the range extender, but is it possible that the laptop Toshiba just don't hear well with it?
Any advice would be welcome.
Thank you
CantonHello Canton
As you know quality of connection WLAN depends on different factors is not easy to say why you have this problem, WLAN. I use Toshiba laptops for a long time now and I didn't notice in the past some serious question of WLAN.
For example I'm 4 router with standard g and have very good signal even in the cellar too or out in the back yard.If possible, try to test the WLAN connection elsewhere. Maybe your friends have WLAN routers so you can test it.
You have a new router or old?
What WLAN standard do you use (b/g/n)? -
Satellite A660-13D - I can't go 65 Mbps with the wireless connection.
+ Sorry for my English is not my mother tongue. +
Hello
I expose my problem:
I can't go to 65 Mbps with the wireless connection. I can't move this connection speed.
Configuration of the laptop:
* Windows 7 Ultimate 64-bit (with all updates installed).
* All the updated drivers correctly.
* With the latest version of the BIOS.Router:
* Tp-link TL-WR1043ND, installed at 3 metres above the laptop (without obstacles).
The router configuration:
* WPA2-PSK AES.
* 802.11n
* Maximum output power.
* Channel: 11 (not automatic, that this channel is relatively free).
* Width of channel: 40 Mhz.
* Maximum tx frequency: 300 Mbps.Other information:
The wireless card drivers are correctly then updated (ver. 5.60.48.35).
* The router has updated the firmware.
* I tried all the settings of the wireless card.
* Bluetooth off (without interference).
* {color: #ff0000} there are other computers on the network that connects 150 and 300 Mbps (with the same network configuration). {color}Thanks in advance,
Greetings.Post edited by: Xibalba
Have you tested using different channels?
Have you tested speed WIFI connected to another router? -
Can I use my printer manually instead of using the wireless connection?
Can I use my printer manually instead of using the wireless connection?
cbg_37 wrote:
It is an OfficeJet Pro 8610.
Hello
It has a print USB 2.0 port, so you can use the printer USB cable to connect it to your computer. This cable may be not in the box, please check if you first buy one (around $5 to $ 10). It is similar to:
Kind regards.
-
How to connect my computer laptop advent for my toshiba tv through hdmi cable.
Please if anyone can help me with this
I bought a hdmi cable to connect my computer laptop advent for my toshiba tv.
BIG PROBLEM
I don't understand the settings. Call me thick but I was actually tryng to fix this for 2 months
I am litrely to the point of screaming and ready to throw the laptop and the tv out the window (WHO COULD BE A SHAME REALLY SEE HOW I AM not ACTUALLY THE TV)
If someone could be so kind as to help and to unmask how and what I have to press on and what to implement in what concerns the settings, I would be so gratefull thanks michelle smith
Hi michellesmithozzyand,
I suggest you follow the link given suggestions and check that it works.
http://Windows.Microsoft.com/en-in/Windows7/connect-your-computer-to-a-TV
Hope the helps of information.
-
How can I connect my computer laptop compac evo n1020 ATI Radeon IGP 340 m of my LCD
Original title: Hello,.
How can I connect my computer laptop compac evo n1020 ATI Radeon IGP 340 m of my LCD? do I need special drivers?
Hello
See the following articles for more information:
Maybe you are looking for
-
If Itunes the other day has decided to return to the folder default itunes media rather than one I chose to use and use successfully for several years. Of course all of the links broken and I couldn't play anything. I'm now trying to get back links b
-
My office print 8600 ProPlus will not print pdf files sent from an iPad with ePrint.
My office print 8600 ProPlus will not print pdf files sent from an iPad with ePrint. I just get an error message when I go to the HP Eprint centre. It prints the address email of the coverage, but nothing else. The attachment is not sure that I ca
-
Satellite Pro A300 - after sleep mode the mouse no longer works
Hi all Hope you can help me with this problem because I believe that I have tried everything I know and my next step is really formatting all the computer again and again without knowing if it will work this time, because that's what I just did, duri
-
Flickering button 'Start' occurs when "Taskbar" is hidden
Have checked the resolution, restarted PC in case a glich, researched in 'help and Support' cannot find how to fix. Anyone know?
-
Hello On my Dev Alpha the Qt BB10 device fonts seem to be in: /base/usr/lib/qt4/libItem but my app is looking for them here: / base/usr/lib/qt4/Fonts How can I make my app look elsewhere? How can I set an environment variable to make this please? Tha