Find the devices tab, then click on 'add a device '.

Similar Questions

• LaserJet Pro M127fn Installer cannot find the device on the network

  Hello

  I just bought the product, but during the installation - setup is unable to find the device on the network. Device is properly registered to the address 192.168.0.14 (with static IP address), I can see the dashboard configiration at the same address via browser and all works well with the network itself.

  Try to ping the IP - it's ok. Tried to install without active firewall - also fails.

  Double checked the installation process - with automatic search and provide the IP address of the printer - both failed.

  Also, I rebooted the router and the switch and the computer. Is not new. I also tried downloading the last executable configuration on the site - and even once, it fails with 'device not found on the network.

  Then what do I do to fix this?

  Thank you

  Finally found a solution. It is strange as it may seem, but after all, it's a solution.

  -Rinse your DNS and your ARP cache (see the Google if you don't know what that means)

  -Reboot the router (or, where appropriate - switches)

  -Change the IP address of the device on your network. Try with round numbers like (192.168.0.20)

  -Restart your router (and if applicable - switches)

  -Restart your computer (s)

  -Don't run the Setup again and the hoprefully you will have no errors and everything works perfectly for you

  If your problem, similar to mine, persists, repeat the above process again and again... and again...

  Good luck

• Find the device based on serial number

  Hi all

  I got a spot on place to locate the Cisco gear in our (hundreds of them), got the serial number but wonder if there is a smart way to find out where is this piece? rather than 'show version' on each device, then look for the serial number. Please teach me. Thank you very much.

  Hi Duke,

  Thank you for using the Cisco Small Business forums. My name is Cristian, I'm a developer of electronic content, and I'm part of the small community of business support.

  Unfortunately, I don't know of a method where you can directly find the device via the serial number. However, I know that Cisco's FindIT uses the CDP of Cisco protocol to detect Cisco devices in a network. You could hover over with the mouse device names and the serial number will be displayed.

  I hope that this response will be useful, and I hope that you respond with questions or concerns.

  * Please answer question mark or note the fact other users can benefit from the TI *.

  Kind regards

  Cristian Gonzalez

  EContent Cisco Developer

• I can't find the Calendar tab

  Im trying to create a slideshow of photos, but I can't find the Edit tab timeline, which is usually at the bottom of your activities... total noob question, but can anyone help?

  Hi, Just figured out.

  step 1. Choose the image instead of video Animation Animation

  Step 2. Click on create image Animation

  It works for me now.

• Try to find the question I posted, click on my contrubtions & he says I posted without question.

  Try to find the question I posted, click my contributions & he says I posted without question.

  I posted a few questions and I can not find them or that the answers.
  Clicking on the e-mail link to verify my email address. So I think I did it right. I just want to know the right way to ask a question and get the answer. This is the 1st time I'am using this forum (this system).

  FireFox froze up on me during my session, but I think I already posted my question, but maybe something got screwed up.
  

  I also pointed out to one of my own post (to give more information). But there is one more. I can't find ether of them now.

  See [920351/questions/920351]

• Where can I find the 'new tab' icon in Safari (El Capitan) v. 9.1?

  Where can I find the 'new tab' icon in El Capitan Safari c. 9.1?

  If there is a + button on the line of tabs, press the key.

  (141457)

• How to find the device ID?

  How to find the device of my CAN ID card and RIO (or card for something else)?

  I use MAX 4.5 and LabView 8.6.

  Thank you.

  Open MAX and go to the section:

  My system > devices and Interfaces > NOR-DAQmx

  It should list all your DAQ devices and say something like

  DAQCard-xxxx: "Dev 0.

  DAQCard-xxxx: "Dev 1.

  etc.

  Just look at your device

• Cannot view XML input using XSL style sheet. Fix the error and then click the Refresh button, or try again later.

  This is the message I got when my backup stopped and said cannot complete backup. Need answers?
  Cannot view XML input using XSL style sheet. Fix the error and then click the Refresh button, or try again later.

  --------------------------------------------------------------------------------

  A name was started with an invalid character. Error during processing of the resources ' file:///E:/WindowsImageBackup/ray-PC/Backup 2011-0...

  Hi lrl1of5,

  (1) do you use Windows Backup and Restore?

  (2) if it works well before?

  (3) remember to make changes?

  It is sufficient to indicate the complete error message you receive.

  Method 1: Run the fixit available in the links below and check if that makes a difference-Worth to try
  Difficulty of broken desktop shortcuts and common system maintenance tasks

  Note: FixIt would attempt to recover bad sectors on the hard disk, in the course of this process there are chances of DATA loss from that particular area.

  Method 2:  Clean boot the computer, then try to backup again

  Follow step 1 in the link below,
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  

  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.

• I downloaded creative cloud, but I can't find the applications tab to help me install Dreamweaver. What should I do?

  I downloaded creative cloud, but I can't find the applications tab to help me install Dreamweaver. What should I do?

  change your serviceconfig.xml, missing Creative Cloud desktop applications tab

• I can't import photos into lightroom free trial cc/6 2015. Lightroom can see all my pictures from my SDHC card and allows me to implement the import, and then clicking import it says that all the selected files (245) has not can be imported as they could

  I can't import photos into lightroom free trial cc/6 2015. Lightroom can see all my pictures from my SDHC card and allows me to select and configure the import, and then clicking import it says that all the selected files (245) has not can be imported because they could not be read. I use MacBook Pro 2015 OS X Yosemite 10.10.3, photos taken with Canon G1 X Mark II. Any ideas?

  This message indicates that you have not permission in writing to the destination directory.

  So:

  1. Determine the destination directory... go in the Lightroom import dialog box and note the location of this directory specified on the right side under "Destination".
  2. Go to your operating system and change the permissions on this exact directory have WRITE permission.

• To install the device driver required to access your hard drive, insert the installation media containing the driver files, then click OK."

  I'm trying to move from xp to windows 7. I spent all the requirement but she says to install the device driver required to access your hard drive, insert the installation media containing the driver files and then click OK. "what should I do? Where can I find the driver?

  Guess he would seek software/drivers for the chipset MB

  & sata/IDE controller software. Get the MB hardware specifications, go to the mfg

  Web site & download the software and drivers. If intel, download the chipset installation

  utility & install it 1. The other would be the SATA or / and drivers for the MB IDE

  controllers, 'Matrix Storage console' would be the one, also chk for desktop

  Internet downloads, amd, and other brand materials would be substantially the same.

• I can't find the Firefox tab to access the option to add a Firefox sync account to my computer desktop from. Where is he?

  The online instructions say click on the Foxfire tab at the top of the page. I can't find this tab. Where can I find this tab so I can create an account to sync to my desktop?

  Hi skadish,

  If you do not see the Firefox tab, you can simply go to Tools > Options > Sync to implement our sync account. The Firefox button can be activated by going on view > toolbars and activation of the menu bar. You don't have to use the menu of Firefox, it's a personal preference.

  Hope this helps!

• find the device

  Hi, today my macbook couldn't not connet to my bluetooth headset. I did something stupid and removed the device and thought it will find, and maybe, this time it will connect. But it is not visible more in the bluetooth settings. Is it possible to insert and reconnect to this device?

  Last night some udates have been installed automatically. I don't know what it is? It might have to do with this update?

  Thanks for your advice

  Hi, Salir518.

  Thanks for the question, and we'll see what we can do to get reconnected to your MacBook Bluetooth headset.  Most likely your headset is not recognized by your Mac because it must be placed in pairing mode.  I'm not sure what headset you have so you will need to get the instructions for pairing online.  The manufacturer usually has this information available on their Web site.  I've included the steps on how to add this audio Bluetooth accessory to your Mac when he was placed in pairing mode in the article below.  Although this article refers to Mac OS X Yosemite, the steps also apply to the Mountain Lion.

  OS X Yosemite: Configure Bluetooth audio devices

  When your Bluetooth headset has been paired with your MacBook, you may have to modify the input audio or peripheral output to your headset.

  Select a Bluetooth audio as the input to your computer or an output device

  1. Choose the Apple menu > System Preferences, and then click sound.

  2. If your device is intended for audio output (for example, headphones), click Exit. If your device is intended for the audio input (for example, a headset), press ENTER.

  3. Select the device you want to use in the list of devices.

  Please let me know if I can be of help and thank you for visiting the communities of support from Apple.

  See you soon

• How to find the 'search' tab

  the Search tab appears, but I can't access it... just try to google search engine

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem.

  • Put yourself in the DEFAULT theme: Firefox/tools > Modules > appearance
  • Do NOT click on the reset button on the startup window Mode safe
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

  Try to delete the file search.json and possible search - metadata.json and search.sqlite files in the profile folder of Firefox to reset the default search engines.
  You can use this button to go to the Firefox profile folder currently in use:

  • Help > troubleshooting information > profile directory: see file (Linux: open the directory;) Mac: View in the Finder)
  • http://KB.mozillazine.org/Profile_folder_-_Firefox

  Firefox will rebuild the file search.json from the default search engines in the folder "browser\searchplugins" in the Firefox program folder and the searchplugins folder in the Firefox profile folder.

  You can check if you have the XML files including Google's default search engine in the browser\searchplugins file in the Firefox program folder.

  If this isn't the case, then you need to reinstall Firefox.

  You can check if you have the XML files including Google's default search engine in the browser\searchplugins file in the Firefox program folder.

  • (32-bit Windows) "C:\Program Files\Mozilla Firefox\"
  • (Windows 64 bit) "C:\Program Files (x 86) \Mozilla.

  If this isn't the case, then you need to reinstall Firefox.

  • https://support.Mozilla.org/KB/search+bar

• New version of Firefox got yesterday and now I can't find the circular arrow to click to refresh a web page.

  I have Windows 7 64 bit
  Long user date Firefox
  Yesterday, I downloaded the latest Firefox browser
  One of the things that the old version was at the top of the page is a
  arrow circle that I could click to refresh a site screen without
  restart the site and become again to this screen.
  He's probably still available if you could help me find it.

  A combined Stop/Reload/Go button that is placed at the right end of the address bar is used in Firefox 4.
  
  During the process of loading page it shows as a stop button and once the charging button is replaced by a reload button.
  
  If you type in the address bar this button would then become a button go.
  
  Click the Reload button to duplicate the current tab in a new tab.

  • http://www.Mozilla.com/Firefox/features.html