find the device

Similar Questions

• How to find the device ID?

  How to find the device of my CAN ID card and RIO (or card for something else)?

  I use MAX 4.5 and LabView 8.6.

  Thank you.

  Open MAX and go to the section:

  My system > devices and Interfaces > NOR-DAQmx

  It should list all your DAQ devices and say something like

  DAQCard-xxxx: "Dev 0.

  DAQCard-xxxx: "Dev 1.

  etc.

  Just look at your device

• LaserJet Pro M127fn Installer cannot find the device on the network

  Hello

  I just bought the product, but during the installation - setup is unable to find the device on the network. Device is properly registered to the address 192.168.0.14 (with static IP address), I can see the dashboard configiration at the same address via browser and all works well with the network itself.

  Try to ping the IP - it's ok. Tried to install without active firewall - also fails.

  Double checked the installation process - with automatic search and provide the IP address of the printer - both failed.

  Also, I rebooted the router and the switch and the computer. Is not new. I also tried downloading the last executable configuration on the site - and even once, it fails with 'device not found on the network.

  Then what do I do to fix this?

  Thank you

  Finally found a solution. It is strange as it may seem, but after all, it's a solution.

  -Rinse your DNS and your ARP cache (see the Google if you don't know what that means)

  -Reboot the router (or, where appropriate - switches)

  -Change the IP address of the device on your network. Try with round numbers like (192.168.0.20)

  -Restart your router (and if applicable - switches)

  -Restart your computer (s)

  -Don't run the Setup again and the hoprefully you will have no errors and everything works perfectly for you

  If your problem, similar to mine, persists, repeat the above process again and again... and again...

  Good luck

• Find the device based on serial number

  Hi all

  I got a spot on place to locate the Cisco gear in our (hundreds of them), got the serial number but wonder if there is a smart way to find out where is this piece? rather than 'show version' on each device, then look for the serial number. Please teach me. Thank you very much.

  Hi Duke,

  Thank you for using the Cisco Small Business forums. My name is Cristian, I'm a developer of electronic content, and I'm part of the small community of business support.

  Unfortunately, I don't know of a method where you can directly find the device via the serial number. However, I know that Cisco's FindIT uses the CDP of Cisco protocol to detect Cisco devices in a network. You could hover over with the mouse device names and the serial number will be displayed.

  I hope that this response will be useful, and I hope that you respond with questions or concerns.

  * Please answer question mark or note the fact other users can benefit from the TI *.

  Kind regards

  Cristian Gonzalez

  EContent Cisco Developer

• iPhone 6 cannot find the device bluetooth audio

  My iPhone 6 (IOS version 9.3.5) Impossible to find a new bluetooth device and keep the search bluetooth unanswered.  In addition, reception (when listening i-tune) is bad and intermittent.  Appreciate advice how to solve this problem.  Thank you.

  Hello ChengMY,

  Thank you for using communities of Apple Support.

  If I understand your message that your iPhone 6 (which is updated to iOS 9.3.5) cannot find a new Bluetooth device and don't stop looking for him. What type of device Bluetooth you are willing to pair with your iPhone? The reason why I ask, is that there are only some that the iPhone supports Bluetooth profiles. Here is a list of the supported Bluetooth profiles:

  iOS: supported Bluetooth profiles

  If the device you are using uses one of the supported Bluetooth profiles, the steps described in the following article can help solve the problem for you:

  Get help connection an accessory with your iPad, iPhone or iPod touch Bluetooth

  Best regards

• Find the device - MacBook Pro stolen-

  find iPhone enabled on the device and sent the lock statement. I had changed my AppleID password immediately (mistakenly?) So far, the unit never came online (3 days).  It is: I will always be able to 'see' and 'communicating' the instruction of lock for the macbook that has the old ApplieID password?  I can not reset old p/w via Apple Automation so any ideas?  Took me half a day to change all passwords app variety and devices in order to identity theft

  It - see If your iPhone, iPad or iPod touch is lost or stolen - Apple Support

• Tecra A2 - audio lost and cannot find the device

  The other day, lost all the sounds on the laptop. Nothing else did it and no new software has been loaded for possibly in conflict or cause a problem. Have you tried to uninstall and reinstall the driver and add hardware (Media Audio Controller) even one time, but system now can't find the (impossible to install this hardware) device.

  You have any recommendations as to the difficulty.

  Thank you
  phwoodford

  Hello

  Have you tried reinstalling the audio driver with the driver of one or the other of Toshiba?

  In addition, it would be interesting to know what operating system you have.
  There is a yellow exclamation marks in Device Manager now?

  Maybe you should try to update the BIOS too. If it doesn t work it seems to be time to reinstall Windows. Maybe something messed with the registry or the system.

• The app "find my iPad" made especially for "family share" and find the device in the event of a flight?

  I thought of what a combined low cost can be found in a House, I would like to find iPad should I have left the room lying around.

  Find my iPad is used to locate the device and also initiates the Activation lock. All find my iPad isn't really designed for the express purpose of locating stolen devices, it can, if the thief left the power on and with an active internet connection. With a Wi - Fi only iPad, which can be difficult. Remember however, that find my iPad must be activated before losing the device to be effective.

• How can I find the device driver (DOT4PRT)

  HP printer says miss me the device driver (DOT4PRT) I don't know where to find or how to download.

  HP printer says miss me the device driver (DOT4PRT) I don't know where to find or how to download.

  HP includes a port DOT4 printer with HP printer driver installation.

  You don't really need this (you can use the standard Windows USB port), but it provides a few extra bells and whistles.

  Uninstall and reinstall your HP printer as shown here: Article 1

• Linksys E2000 can not find the device!

  Hello

  I have Windows 7.

  My ISP is a DSL company. I've been with this company for several years now.

  I still have in my possession a wired router that I am currently using as my E2000 does not work.

  In my computer, I have a network and a wireless network card. Both claim that the ' device working properly "in the Device Manager.

  I tried to do the work of E200 for awhile now and I'm about to return it to the store and buy something else.

  I insert the CD and I followed instructions more than once (even tried different things).

  I always get to the screen that says:

  We now set up your LinkSys E2000.

  Please wait, this may take up to 5 minutes.

  Aftetr awhile I get the message saying that it cannot find a device and that if I use a laptop that there could be a 'switch '. When this does not work I can plug in the back of my old router and it works fine.

  I bought this router 7 days ago and it still does not work. I used to work for a DSL company and I was in technical support. I'm not a beginner.

  Please help that this is the first time that I buy a product Linksys. I'm about to lose patience with this.

  Thanks in advance

  So long Linksys you're going back to the store. Never

• can not find the device via blue tooth

  I can't pair my rapooH6080 with my laptop (windows 7 ultimate 86 bit Asus A46C series). I can't find my headset with bluetooth ad device option. I'm totally stuck.please help.

  The question therefore, with the laptop.

  Ypu can find the drivers here:

  http://support.ASUS.com/download.aspx?SLanguage=en&m=A46CM&OS=8

  If you can't find the drivers or the drivers are not compatible, contact Asus support for assistance.

• Find the device on the network

  Could someone please explain to me how to find a device on a network - use the multicast or broadcast?

  I want to find the ip address of my server on wlan and there may be multiple instances of these servers. The server uses this http://www.blackberry.com/developers/docs/7.0.0api/net/rim/device/api/io/MulticastDatagramConnection... class and receives repsonses ok. Java then sends a rear channel.

  I get only the following c ++ side while I'm hoping to receive a string any (that im sending java) so I can identify what responses come from my server. and which are not.

  M-SEARCH * HTTP/1.1
  HOST: 239.255.255.250:1900
  St:urn:schemas - upnp - org:device:InternetGatewayDevice:1
  MAN: "" ssdp: discover ""
  MX:3

  And here is my code to send and receive...

  int receiveMulti()
  {
       struct sockaddr_in addr;
       int fd, nbytes,addrlen;
       struct ip_mreq mreq;
       char msgbuf[1024];
  
       u_int yes=1;            /*** MODIFICATION TO ORIGINAL */
  
       /* create what looks like an ordinary UDP socket */
       if ((fd=socket(AF_INET,SOCK_DGRAM,0)) < 0) {
        perror("socket");
        exit(1);
       }
  
  /**** MODIFICATION TO ORIGINAL */
      /* allow multiple sockets to use the same PORT number */
      if (setsockopt(fd,SOL_SOCKET,SO_REUSEADDR,&yes,sizeof(yes)) < 0) {
         perror("Reusing ADDR failed");
         exit(1);
         }
  /*** END OF MODIFICATION TO ORIGINAL */
  
       /* set up destination address */
       memset(&addr,0,sizeof(addr));
       addr.sin_family=AF_INET;
       addr.sin_addr.s_addr=htonl(INADDR_ANY); /* N.B.: differs from sender */
       addr.sin_port=htons(1900);
  
       /* bind to receive address */
       if (bind(fd,(struct sockaddr *) &addr,sizeof(addr)) < 0) {
        perror("bind");
        exit(1);
       }
  
       /* use setsockopt() to request that the kernel join a multicast group */
       mreq.imr_multiaddr.s_addr=inet_addr("239.255.255.250");
       mreq.imr_interface.s_addr=htonl(INADDR_ANY);
       if (setsockopt(fd,IPPROTO_IP,IP_ADD_MEMBERSHIP,&mreq,sizeof(mreq)) < 0) {
        perror("setsockopt");
        exit(1);
       }
       printf("beforeread");
       fflush(stdout);
       bool keepGoing = true;
       int count = 0;
       /* now just enter a read-print loop */
       while (keepGoing) {
           count++;
        addrlen=sizeof(addr);
        if ((nbytes=recvfrom(fd,msgbuf,1024,0,
                     (struct sockaddr *) &addr,(socklen_t*)&addrlen)) < 0) {
             perror("recvfrom");
             exit(1);
        }
        msgbuf[nbytes] = '\0';
        printf("received: %d  %s", nbytes, msgbuf);
        fflush(stdout);
        if(count > 5)
        {
            break;
        }
       }
  }
  
  int sendMulti ()
  {
       struct sockaddr_in addr;
       int fd, cnt;
       struct ip_mreq mreq;
       char *message="83383329092240912";
  
       /* create what looks like an ordinary UDP socket */
       if ((fd=socket(AF_INET,SOCK_DGRAM,0)) < 0) {
        perror("socket");
        exit(1);
       }
  
       /* set up destination address */
       memset(&addr,0,sizeof(addr));
       addr.sin_family=AF_INET;
       addr.sin_addr.s_addr=inet_addr("239.255.255.250");
       addr.sin_port=htons(1900);
  
       /* now just sendto() our destination! */
      // while (1)
       {
        if (sendto(fd,message,sizeof(message),0,(struct sockaddr *) &addr,
               sizeof(addr)) < 0) {
             perror("sendto");
             exit(1);
        }
        sleep(1);
       }
  }
  

  tjhanks.

  It turns out that my hypothesis the code example I used sends the group with this line of code is incorrect...

  String remoteAddr = dgram.getAddress();
     String msg = "Hi";
  
     dgram = conn.newDatagram( msg.getBytes(), msg.length(), remoteAddr);
  

  remoteAddr gives me //192.168.0.5:65228;4321| rear UDP I used to send the data back to c ++ but when I just changed my group address and port manaually packets are received on the side of c ++.

• Find the devices tab, then click on 'add a device '.

  I just set up my desire to 4500 and received a page telling me to create an account on hp connected, select the "Devices" tab and click on 'Add a device' then enter the claim code on the printer (which only lasts 24 hours!). I can't find the tab "Devices". Please can you tell me where to look. I see that other people have had the same problem.

  Hello

  When connect to your HP account logged in, you can see 4 big black words just under connected HP. The devices tab is 4th from left.

  Kind regards.

• How to find the device is roaming

  Hello

  I need to test if the coverage is roaming.

  I went through the thread:

  http://supportforums.BlackBerry.com/Rim/Board/message?board.ID=java_dev&message.ID=41137&query.ID=82...

  Who says

  boolean isRoaming = (0 != (RadioInfo.getState() & RadioInfo.NETWORK_SERVICE_ROAMING));
  

  I tested it on the device and emulator and both give me the value.

  The RadioInfo.getState are '1' and RadioInfo.NETWORK_SERVICE_ROAMING gives '8 '.

  and that's the reason why he fake retruning.

  When I check the connection management option, it says that its on Roaming.

  I have Blackberry Pearl 8130 version 4.5.0.66 (CDMA)

  You must use getNetworkService() instead of getState().

      public boolean isOnRoaming() {
          boolean returnable = false;
          if (((RadioInfo.getNetworkService() & RadioInfo.NETWORK_SERVICE_ROAMING) != 0)
                  || ((RadioInfo.getNetworkService() & RadioInfo.NETWORK_SERVICE_ROAMING_OFF_CAMPUS) != 0)) {
              returnable = true;
          }
  
          return returnable;
      }
  

• Can not find the device

  I use the C6180 all-in-one printer.  I use the software driver or the newest utility on the HP website.  I use a relatively new MacBook Pro with OS X 10.5.6 and all updates.  I connect the printer to the network via LAN cable.  I can print to the printer very well, but I can't communicate with the printer to do other things, for example, copy or scan.  When I use the HP Device Manager and go to 'Information and settings' and select 'Choose the Device', no device appears in the window under "select your HP all-in-One device.  All of the tasks that I try expires because no device is found.

  How to associate the printer to my computer so that I can use the functions 'all' of my printer 'all-in-one '?

  Thank you

  Mike

  Solution: I have turned to cycling the printer, but that has not changed anything.  I then used the Setup Assistant, which I thought I had already done when I originally installed the software.  But I do not... I have seen a few pictures, I had not seen before and after that I saw an entry in the device dialog box.  Everything seems to work now.