Flow max SlotRadio
When I put an mp3 file with 383 kbps VBR the SlotRadio redemmare constantly. Although it works OK when I put a CBR 128 Kbps file.
What are the limits on the Kbps and VBR/CBR.
The 383 is probably a wrong number, reported by Windows Explorer.
In any case, I changed the bitrate to VBR 190 use Foobar2000 + lame and now everything is OK.
Tags: SanDisk Sansa
Similar Questions
-
HP Jet 11: Resolution of HDMI output / flow Max 11 HP?
Hi, I just ordered the version of Windows 10 2015 11 flow HP and I thought using an external monitor with her to the House on HDMI. I like the look of a 2560 x 1440 resolution, I was wondering can the flow 11 this output over hdmi resolution? Thank you!
Hello
No, it only supports FHD 1920 x 1080 (or 1200).
Kind regards.
-
HP Z600 basic workstation: 3.1 in a workstation Z600 Usb Adapter
I would like to know if the Z600 will support the 3.1 USB card and if so, do I need for installation?
Okay... that card should work in a Z600, but it will operate at the speed of 10 Gbps USB 3.1 standard? N °
The HP Z600 workstation has no generation PCIe connectors 3. It has 3 PCIe Gen2, 1 PCIe Gen1 slot slots and 2 PCI slots. Here is a link to the page HP describing the slots of the Z600:
http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c01719695
Here is a note of StarTech regarding the speed of the card, points out: "the maximum speed of this card is limited by the bus interface. Flow max PCI Express Gen 1.0 is 2.5Gbps. PCI Express Gen 2.0 flow max 5Gbps. High-speed PCI Express Gen 3.0 max is 10 Gbit/s. Available bandwidth (10 Gbps) is shared equally between the two ports. »
These cards in PCIe USB 3.0/USB 3.1 generally need supplementation of power... the + 5V they need does not come to the top of the slot, but it's easy to find a device to SATA power adapter 4 son "molex" which can provide 5V power higher they need to meet potential power draw (compared to what needs USB 2.0). All this information comes from research find how to add Texas Instruments base HP USB 3.0 card to our xw6600 workstations, that have 2 PCIe Gen2 slots (the others are Gen1). Z620 gives you some Gen3 PCIe slots... Slot 2, 4 and 5.
Here is the diagram of slots Z600:
-
ASA 5505 transparent mode dosnt pass traffic
Hi all
need help
ASA 5505 do not pass traffic as a cordon of brewing, how do you get traffic?
ciscoasa # sh ver
Cisco Adaptive Security Appliance Version 8.2 software (5)
Version 6.4 Device Manager (5)
Updated Saturday, May 20, 11 16:00 by manufacturers
System image file is "disk0: / asa825 - k8.bin.
The configuration file to the startup was "startup-config '.
ciscoasa until 55 minutes 31 seconds
Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor
Internal ATA Compact Flash, 128 MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024 KB
Hardware encryption device: Cisco ASA-5505 Accelerator Board (revision 0 x 0)
Start firmware: CN1000-MC-BOOT - 2.00
SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.05
0: Int: internal-Data0/0: the address is e4d3.f193.9486, irq 11
1: Ext: Ethernet0/0: the address is e4d3.f193.947e, irq 255
2: Ext: Ethernet0/1: the address is e4d3.f193.947f, irq 255
3: Ext: Ethernet0/2: the address is e4d3.f193.9480, irq 255
4: Ext: Ethernet0/3: the address is e4d3.f193.9481, irq 255
5: Ext: Ethernet0/4: the address is e4d3.f193.9482, irq 255
6: Ext: Ethernet0/5: the address is e4d3.f193.9483, irq 255
7: Ext: Ethernet0/6: the address is e4d3.f193.9484, irq 255
8: Ext: Ethernet0/7: the address is e4d3.f193.9485, irq 255
9: Int: internal-Data0/1: the address is 0000.0003.0002, irq 255
10: Int: not used: irq 255
11: Int: not used: irq 255
The devices allowed for this platform:
The maximum physical Interfaces: 8
VLAN: 3, restricted DMZ
Internal guests: 10
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
SSL VPN peers: 2
The VPN peers total: 10
Double ISP: disabled
Junction ports VLAN: 0
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabled
This platform includes a basic license.
Registry configuration is 0x1
Modified configuration of enable_15 to 20:34:47.689 UTC Wednesday 5 December 2012
ciscoasa #.
ciscoasa #.
ciscoasa # sh run
: Saved
:
ASA Version 8.2 (5)
!
transparent firewall
ciscoasa hostname
activate 8eeGnt0NEFObbH6U encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
I haventerface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
Shutdown
!
interface Ethernet0/3
Shutdown
!
interface Ethernet0/4
Shutdown
!
interface Ethernet0/5
Shutdown
!
interface Ethernet0/6
Shutdown
!
interface Ethernet0/7
Shutdown
!
interface Vlan1
nameif inside
security-level 100
!
interface Vlan2
nameif outside
security-level 0
!
passive FTP mode
outs_in of access allowed any ip an extended list
outs_in list extended access permit icmp any one
pager lines 24
Within 1500 MTU
Outside 1500 MTU
no ip address
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
outs_in access to the interface inside group
Access-group outs_in in interface outside
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:234e9b9c6c9c941a89e37011325b6d5e
: end
ciscoasa #.
ciscoasa #.
ciscoasa #.
ciscoasa # sh - access list
access cached list the ACL log stream: total 0, 0 (deny-flow-max 4096) denied
alert interval 300
outs_in list of access; 2 elements; hash name: 0xd6c65ba5
permit for access list 1 outs_in line ip scope any a (hitcnt = 0) 0x7d210842
allowed to Access-list outs_in line 2 extended icmp any a (hitcnt = 0) 0x5532fcc5
ciscoasa #.
Hello
Exactly... Good to know it works now.
Do you know why he needs the IP address (such as a transparent firewall)?
The ASA will act as a transparent layer 2 on the right device to the network, but what happens when the ASA does not have a particular destination mac address... What would be the source ip address of the package? Ip address of the ASA. So that's the main reason why we need that.
We use it also for traffic management and for AAA services (if authentication is used the ASA will send the AAA authentication request to the server) with the IP address of this source.
Please check the question as answered, so future users can pull of this
Julio Carvajal
Costa Rica
-
ASA 5510 using only the GB interfaces
I am looking for should I use a 5510 to activate two interfaces for VPN connections broadband from only a few sites. Our 5505 s (I have dozens) can not manage speeds of more than 100 MB and I have now a few FIOS beyond that--150 to 300mpbs. I want a 5510 basis who needs to manage a few voice / data sites and just use two interfaces. A basic 5510 allow 2 gigabytes or just ports FE interfaces? I have to be able to use 2 GB interfaces and no one else. I don't know that the 5510 will probably support the same QOS settings that I use on the 5505 s... I just need more speed interface so that I'm not bottlenecking data (I know I could use several 5505 s and extend the charges but is not how I want to do it for other reasons). Thank you
Hello
To my knowledge the ASA5510 supports 2 x 1 Gbps interfaces when you the Security license for the SAA. The basic license counts 100Mbps interfaces.
Take a look at this document for more information on licensing above
http://www.Cisco.com/en/us/docs/security/ASA/asa82/license/license82.html#wp190732
Its a document from the 8.2 version but its still even to 9.x on the license requirement more security get the 2 x 1 Gbps interfaces
The documentation for ASA5500 series promises an 300Mbps for the ASA5510 model flow, but I guess that's a value of location. In the most recent document, two values of max flow max and Multiprotocol are given.
Here's a link to the document
-Jouni
-
VPN Site to Site Ping from one to the other network failed
Hello
I just get what I can do a VPN IPSec Site to Site. But if I try to send a ping to a PC (network 1)
There not for the other PC (network 2).
PC (network 1)
switch PC (network 2) between the two ASA I funkctional IPSec VPN tunneling, but I can't access from one to the
another network. So I hope I will get help here.
What are the access on the ASA5505 list:
ASA5505 #.
access cached list the ACL log stream: total 0, 0 (deny-flow-max 4096) denied
alert interval 300
Inside_ICMP list of access; 4 elements
allowed to Access-list Inside_ICMP line 1 extended icmp any any echo response
allowed to Access-list Inside_ICMP line 2 extended icmp any any source-quench
permit for access list Inside_ICMP line lengthened 3 icmp all all inaccessible
allowed to Access-list Inside_ICMP line 4 extended icmp exceed all once
outside_cryptomap_2 list of access; 2 items
access-list outside_cryptomap_2 line 1 comments ACL traffic von ASA5505 zur ASA5510
allowed to Access-list outside_cryptomap_2 line 2 extended ip 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.0
allowed to access list lengthened 3 icmp outside_cryptomap_2 line 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.0
no_NAT list of access; 1 items
access-list 1 permit line no_NAT extended ip 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.0
ASA5505 #.
Access-group Inside_ICMP in interface outside
NAT (inside) 0-list of access no_NAT
card crypto outside_map 2 match address outside_cryptomap_2
The inside interface has IP 192.168.1.1
The access list I also on the other ASA network are changed.
Could someone help me it will work.
Best regards
Hans-Jürgen Guenter
Please mark this thread as a response but at the moment it is now "not answered", so that it will receive another somoene solve similar problems.
Thank you
-
mixture of 1080 and 720 images in the same project
Hello
I am new to Adobe Premiere and still learn the in and outs of the software.
I had shot some footage with my Go Pro in 1080 p/30 FPS and I have pictures recorded in 720 p/30 fps that I wanted to include in a project
My problem is that I noticed a decline in the quality when you export.
I had exported with the following parameters:
H.264
Vimeo HD 1080 p
Go to maximum depth
Target the bitrate, flow Max: maxed out
Maximum render quality
Would be - this due to the fact that I have a 720 p movie in my project? And that he compensate?
Is there a way to keep the project at the 1080 for 1080 images and keep the 720 720 in the same project?
More than 100% scaling will degrade the quality.
You can export at 1080, leaving a black frame around the 720 hardware, so it's not zoom.
The best solution is probably just export to 720 and adjust images 1080 down a bit.
-
Pe11: DVD burning: bitrate?
Here, I noticed that you can't choose a flow for burning to dvd format (this is also my experience).
But is the bitrate PE11 uses?
I assume that's what variable so if the sequence is long bitrate will be lower?
But wat is the bitrate if you have Te footage of only 20 minutes?
fredowww66
Premiere Elements has always had a setting flow max 8.00 Mbit/s in the dialog box burn quality area. This isn't my answer or an answer from someone else. It is the answer of the program.
This max 8.00 Mbps is for DVD 4.7 GB / 120 minutes, as well as if you use DVD 8.5 GB / 240 minutes. I can get into more details in this regard between and with "good content to the space available.
Here is the reading of properties watch MediaInfo of a typical DVD-VIDEO to DVD disc that I just created in another goal. I did not exceed the capacity of the disk, so the max flow showed burn 8,00 Mbit/s in the field of the quality of the dialog box before they hit the burn button. Note the display of bitrate for the video stream of the DVD-VIDEO. The results are typical and are less than 8.00 Mbps. try it. MediaInfo to make one of these readings can be obtained from
http://MediaArea.NET/en/MediaInfo
The flow values indicated by MediaInfo are in Kbps (kilobits per second) and not Mbps (megabits per second). So to put it in perspective:
7813 Kbps = 7.63 MB/s
6955 kbit/s = 6.79 Mbps
Still, there is no possible throughput Mbit/s max 9 possible for DVD-VIDEO produced by Premiere Elements (this is stated in the dialog box burn quality area to burn to disk, or in the final product in which you can see using a variable bitrate).
http://en.Wikipedia.org/wiki/Variable_bitrate
Please consider and prove to yourself with the easy verification that I have suggested.
Thank you.
RTA
-
What is the projected cost of virtualization?
I ran a few tests to test discs, CPU and memory.
(Intel XEON 5400 Series, 4 cores, 1 processor clocked at 2.66 GHZ, 4 GB RAM, concert 146 local 10 000 RPM SCSI, RAID-1, FreeBSD 7.1 64-bit)
-The drive seems OK. (diskinfo - t) It shows virtual faster than natives, but then the disc size is less physical, and there may be some early reading going on there. Whatever it is, worst case is habitable, and the best of cases, it is much faster. I'm not disc related in any case.
Native:
Transfer rate:
outside: 102400 KB in 0,740411 s = 138302 KB/sec
Middle: 102400 KB in 0,590457 s = 173425 KB/sec
inside: 102400 KB in 0,816407 s = 125428 KB/sec
Virtual:
Transfer rate:
outside: 102400 KB in 0,740411 s = 102478 KB/sec
Middle: 102400 KB in 0,590457 s = 225934 Kyte/s
inside: 102400 KB in 0,816407 s = 232638 KB/sec
-Memory and CPU, the CPU has lost about 16 percent, which looks all right. Memory is declining by 50% which is not what I was expecting:
Native
Ubench CPU: 1346168
Ubench MEM: 228570
-
Ubench AVG: 787369
Virtual MACHINE with VMware Tools installed:
Ubench CPU: 1129519 (-16%)
Ubench MEM: 115477 (-50%)
-
Ubench AVG: 622498 (21%)
I played a few games with the amount of memory, CPU, etc. None of this
has worked. In fact, if I gave the VM just and all of the memory and CPU
Let the VMware to make management of the resources and planning instead of me, he
climbed, MUCH, MUCH better than me the trying to help reserving CPU or
RAM for the hypervisor. It is not even close. I learned the hypervisor does a much better job of planning of resources so I don't "help". I tried para, but it wouldn't start even in this way.
I've seen several thorough tests done around the web and they systematically put the cost of virtualization at 25%, enough for this type of virtualization where VMs do not share the same kernel and 10% when they do. It is possible that combo in the real world, this would align their conclusions of 25% penalty according to the CPU at the mixture of memory. I would just catch someone is about to implement and make the ubench test and see if your fate like mine. It would be preferable if you have tested with a core of 4. I noticed that you drop carrots, the cost of virtualization as a percent of the total increases disproportionately. It is the opposite of physics where the addition of kernels normally has a rate of return. That could make someone with a sensation of 2 core as if there is something wrong when it is quite normal.
Thank you!
What product you use VMware?
1 hdparm, diskinfo and similar tools will give you not very reliable results. Calendar inside a virtual machine that is also perhaps not too reliable when executing such tested.
During an iometer test, I got the following results:
SERVER TYPE: Windows physics 2003R2sp2 (not a virtual machine)
TYPE of CPU / NB: 8 processor cores, 2 Sockets
HOST TYPE: HP DL360G5, 4 GB OF RAM. 2 x XEON E5345, 2.33 GHz, QC
TYPE of STORAGE / DISK NUMBER / RAID LEVEL: P400i, 256 MB 50% cover reading.
2xSAS 15 k RPM / raid 1 / 128KB stripe size / ntfs default block size
(4096)
NAME OF THE TEST
AV. Ms resp time.
AV. IOs/s
AV. MB/s
Flow max - 100% reading.
3.18
18530
579
Reading of Rand - 65% RealLife - 60%
78.6
739
5.7
Flow max - 50% read
3.74
15579
486
Random reading - 8 k - 70%.
72.7
787
6.1
SERVER TYPE: Windows virtual 2003R2sp2 on ESX 3.0.2. Time service tend to disabled
TYPE OF CPU / NB: VCPU / 1
HOST TYPE: HP DL360G5, 4 GB OF RAM. 2 x XEON E5345, 2.33 GHz, QC
TYPE of STORAGE / DISK NUMBER / RAID LEVEL: P400i, 256 MB 50% cover reading.
2xSAS 15 k RPM / raid 1 / 128KB stripe size / default vmfs 1 MB
NAME OF THE TEST
AV. Ms resp time.
AV. IOs/s
AV. MB/s
Flow max - 100% reading.
5.3
9711
303
Reading of Rand - 65% RealLife - 60%
43
786
6.1
Flow max - 50% read
6.4
8796
274
Random reading - 8 k - 70%.
55
778
6
2. what you have observed on memory is probably right, since you are using a processor intel cpu. New AMD processors have more fast memory manipulation because they support IVR.
3. Although VMware Workstation and Fusion support directX9, several new games does not work well.
4. add multiple virtual processors to a guest, is also something that you are only advised to do so only when necessary, even if ESX3.x handles this better that hosted products.
-
Reduces the size of the HD DVD image for SD images in still
CS5 using, when I encode a sequence of SD, first in still, everything works fine. When I downconvert an HD project by SOUL, it seems very well and shows full-screen in yet, but when I burn a DVD and read it, I get an image of reduced size in the center of the screen.
I'm shooting 1080 24 p with a Panasonic HPX170 camcorder. I create files AVI Microsoft using the site.
I use a Matrox MXO2 Mini with Max display unit, so I am using these project creation settings:
Matrox HD
1990 x 1080
I export the chronology of creation with the recommended settings in the Jeff Bellune CS4 tutorial to convert first HD to SD images for burning DVDs
FORMAT: MPEG2-DVD
23.976 p PRESET NTSC widescreen quality
VBR 2 PASS
Maximum render quality
Flow rate 2.8 min
Flow target 7
Flow max 8
GOP PARAMETERS M 3 N frames12 frames
Kh PCM 16-bit audio 48
Multiplexer NO
When I make files and build a project with again, the image of the timeline and menu appear full screen on the review screen.
When I burn the project on DVD, it displays correctly in the mailbox on a def tv standard.
But when I play the DVD on an HDTV, I get a big picture of research in appropriate proportions, but it displays to approximately 3/4 size in the center of the black screen that surrounds it. I can change the configuration of the display on the HD TV to "Zoom" and fills the screen with the image without distortion. "
I have the same problem of creating images to 1080i 60 fps and 1080 p 30 fps and construction projects with parameters in first and still.
I wonder if Miss me a setting in the SOUL or. I thought I had followed instructions excellent Jeff Bellune on HD to the parameters of the SD in the SOUL to the letter.
I would like to create DVDs that will play full screen on HD televisions and in the box to the letters on a standard def TV without having to change the settings on their TVs high definition to viewers.
FYI, I'm shooting in HD, partially to get really own keys to the course change, using the Ultra keyer in first. It works very well.
Thanks for any help.
I still want to find settings that will build a DVD that can be played by viewers who don't know how to change the settings on a DVD player or TV sets. I'd like my DVD disc to play in the same way that a disk trading DVD play a movie full screen with no adjustment for the DVD player.
Is not possible. Even commercial/Hollywood records are incorrectly displayed by users who cannot or will not set up their players and televisions properly. For example, to insert a DVD widescreen anamorphic in the DVD player and say the DVD player the TV is 4:3 (even if it's a 16:9 HDTV). Cycle then the TV through all its report parameters; you will see quite an array of distortions and image sizes, only which is the right size of ratio and image.
That said, if commercial discs if displays correctly using parameters you have, then properly drafted widescreen DVD from en should work correctly as well. 2 BD players (which assume a TV 16:9 by default) display it correctly also indicates the settings on DVD players are false.
Jeff
-
CS4 - Adobe Media Encoder->; still - H.264 Blu - ray
As many people are aware, transcoding yet can sometimes be less than optimal. I played with the settings of the SOUL and with the help of other people on these and other forums sliced all the right settings, while still would treat my native DVD quality videos and do not attempt to transcode the.
I am now trying my hand at the Blu - Ray and facing me similar problems, but so far I have not really found any answers that have worked. According to my research, the following should work:
SOUL
------
Format: H.264 Blu - ray
_Video_
TV standard: NTSC
Image size: 1920 x 1080
Frame the oar: 23.976
Field order: no (progressive)
Format of the pixels: screen 16:9 wide
Profile: high
Level: 4.1
_Bitrate settings
Encoding Bitrate: VBR 1 Pass
Target Bitrate: 18
Flow Max: 22
_Audio_
I disabled because I'm using DD 5.1 encoding and for the quality of DVD, I learned that multiplexing is a no-no to prevent still trying to transcode the things of multiplexing. I guess the same applies to the Blu - Ray, so I'm not really worried about the Audio.
Yet
---------
_Project Settings_
Design: Blu - ray
_Settings
TV Standard: NTSC
Codec: H.265
Dimensions: 1920 x 1080
Frame rate: 23.976
Fields: No fields (progressive scan)
_Automatic transcoding
Maximum video bit rate: 25.0 Mbps
_Audio transcoding
Audio transcoding scheme: Dolby Digital
I tried a number of other parameters around these (including using 29.97 frame rate to match my source), but after 4 days trying different things with the SOUL, I am completely puzzled. What I want is someone to be kind enough to post their settings, in the level of detail above, allowing them to import an asset again so that it does not transcode the video.
I know there are other tools out there that can do these things, but I paid my $ for Adobe Mastersuite so that he would do these things for me. If possible, I would definitely stay with these tools.
I don't know if it's important, but my source is that a Panasonic HDC-TM700 set to record 1080 p 30 (I do not use of their proprietary format of 60 frame). I have successfully reduced this source with SOUL DVD quality. I also managed issued by SOUL 1080 p which was uploadable on Youtube. Still, I'm not sure it is important to others that I have used my source video. Here are the properties of the video according to the first:
Type: MPEG Movie
File size: 2.6 GB
Image size: 1920 x 1080
Sampling: 32
Frame rate: 29.97
Audio Format: 48000 - compressed - Hz 6 channels
Project Audio Format: comma floating 48000 Hz - 32 bit - 6 channels
Total duration: 00; 22; 23; 25
Average data rate: 2.0 MB/second
Pixel format: 1.0
My actual clip is about 6 min, but my intention is to use clips of up to an hour in length.
Oh, I'm not sure if it is clear from my above information, but I'm not using Adobe Dynamic Link. I don't know if it is my problem, but my attempt to use has not produced the results I was looking for either.
Thanks in advance for your time and to make it this far in my post
-Jay
Normal audio transcoding. Blu - Ray, you can manually than to use the right PCM change.
I just tried very preset and video, as expected, was listed as not transcode as Blu - ray. Make sure you are looking not to the status of transcoding from DVD?
-
Hello
I have problems with burning double-layer DVDs in Encore. I noticed another recent post - I don't know if this is the case http://forums.adobe.com/thread/827366?tstart=0. Before you start buying and replacement of equipment, I thought I'd get tips here.
The problem - my first burn contained several places where the video pauses when played on a DVD player. To determine that the DVD drive is not faulty, I then played the disc in the DVD of PC burner and encountered the same problems. I burned another disc of in yet and most of the problems have disappeared. There are still places where to get a break. It is likely that the DVD burner is unreliable or dying, or is there something a pc or a point of view that I should try?
Some info:
The original material was made in PrPro CS 5 without rendering quality max and without depth max. CS 5, it is imported with the rate of 9.4 and transcoded with quality = high quality 7MB VBR 2 Pass and av NTSC setting flow max = 9.4mbps, rendering quality max, and and the mpeg-2 codec.
Hardware - Core 2 Duo, 4 GB 1066 DDR2 RAM E6700, Nvidia GTX 480 with MPE hack,
DVD burner - Plextor PX - 755 has.
OS - Win 7/64
Additional notes:
I need to burn DL disks by starting again with admin rights.
The problem does not occur with dvd discs single layer.
Thank you
Steve
I always use again to create an ISO on my data disc and then use the FREE
http://www.imgburn.com/index.php?act=download to write the disc
In Imgburn, I check the slowest possible speed burn and to DL, I always use Verbatim
Never a problem
-
Fix multimedia Format for iTouch 3rd generation
I was asked by a client to provide a training video that can be imported to the iTouch 3rd generation of devices for employees. The idea is that employees download the video from the company's intranet, then load on their iTouch via iTunes.
I tried the two models inPreimer CS4 for Apple TV and iPod big but once, nor file could be imported from iTunes for the iTouch.
I searched on the internet and even tried to find a resource on the iTunes store by submitting uneducated directly to iTunes video podcast that I did a couple of years for another customer, but I couldn't find their listed standards any longer.
There is little available in regards to the actual characteristics of the frequency of video images, flow max, progressive, interlaced, wide format (430 X 280) 4:3 and the audio settings. Again the goal is to allow employees to settle these video. If the format is not correct, iTunes will fail the synchronization or download on the local device iTouch one so far, I'm batting 0.
Some employees may have older ipods, which seem to be a lot less special, so my first goal is the newest 3G iTouch where I had no chance.
Could someone please help.
Thank you very much!
CABAC should be turned off during the H.264 encoding for iPods of generation, and as much as I know there is no way to do it in the PR.
Export of Pr in format .mov Photo-JPEG and import that into Quicktime Pro (30 or 40 dollars) for the respectful .mp4 files encoding for the iPod. We can talk about parameters in QT Pro if you decide to go this route.
-Jeff
-
Error of flow OR MAX and attribute camera out of reach
I recently bought a camera Point Grey Grasshopper3, it seems to work fine at point software fly Cap Gris provides, but I get an error NI Max when I try to do a simple puncture (see below). This error appears every time I try to catch a time image the first after the opening OR MAX, even if the flow is set to maximum. Then I change the flow under control of the unit to any integer 125000000 max, and the camera works very well for MAX. It will capture images as much as I need. Then I save the camera output MAX, open MAX once again, it shows my saved settings, I'm going to capture images and I get the error again. If I change the range regardless of the number and it works again in the same session in MAX.
I had a gray point Zebra2 work very well and he used in my program LabVIEW with IMAQdx to acquire images. When I try to use grasshopper3, LabVIEW returns error attribute camera out of reach of the VI camera configuration. I use to test the camera of the VI is the camera just to open, configure acquisition, start acquiring, get the picture, cancel the acquisition and nearby IMAQdx camera configuration. I did twice open MAX, change the flow, save the camera, close MAX without grasping an image and then was able to acquire images in LabVIEW in the first inning. I would run the VI once again and then it returns the error to attribute camera out of reach. I changed the packet size, resolution and the frame rate of the camera with a difference in errors.
Since I am able to images of the stream from the camera to the gray point fly capture and Max after activating/deactivating the flow layout, it leads me to believe there is some sort of error MAX/LabVIEW that prevent me to capture the images.
Any ideas? Has anyone else had this problem with MAX and LV?
Looks like the point Grey cameras showed this error before the firmware on the basis. See this linkfor such a forum. I would monitor the camera (*.icd) file located in the data folder IMAQdx in public Documents to see if the actual value is be replaced after the configuration of the camera has been saved in MAX. There is a chance that the GigE. XML file which is transferred from the camera is overwrite these values in the unacceptable value. See this linkfor a KB about this error, which leads me to believe that this may be the problem.
-
Micro WUSB6100M Max-flow AC600 Linksys Wireless USB adapter
Hi, is the Linksys WUSB6100M Max - AC600 Wi - Fi USB adapter Micro Stream works on a raspberry ft3? Ted +.
Hello
Thank you. I use a Linksys AE1000 right now on my ft3 raspberries and it works fine I just wanted to use a faster and more stable, so I can stream HD and 4 k on my raspberry ft3 so I thought that the AC600 MAX-FLOW micro USB wifi adapter would do the trick, but I'm not sure. I would like to buy one but not if it does not work on the ft3.
Ted +.
Maybe you are looking for
-
Site has worked very well for a long time. Personally, I use Firefox. To test: select a section, that is B J Minis elements c. click on the basket to the top element and you will get a popup that allows only continue shopping, nothing is added to you
-
I want to go back to Firefox 3.6; How can I do?
I've updated to Firefox 4 and I don't prefer it to Firefox 3, 6, so I want to unupdate. Can you tell me how to do this? A problem with FF4 is that whenever I opened gmail, after one minute, the view of the screen indicates that it will not work with
-
Google on the Xoom account login failure
I just got my Motorola Xoom of BestBuy and I had time to add my Google account to the device. I had recently activate 2 factor authentication on my Google account and I thought this might be causing the problem. I DISABLED the 2 factor Auth and the X
-
I upgraded my OS XP to Win7 32 bit. Updated driver of chart fx1600m. Now, the laptop will start OK on battery, but BSoD when booting with AC (90w) power. Have purchsed 120w power supply current, but makes no difference. Once started on drums, can co
-
HP Officejet Pro 8100 turns off.
After that I use this printer, if it is an hour or more, next time I want to print, I have to press the start button to restart the printer. I must have configured incorrect, because it's the first HP printer who acted in this way.