Greenscreen Setup ok - any tipps?

Similar Questions

• Is Version 1 available Utility Setup WPSM54G any where?

  Anyone know where I can download the Version 1 of the configuration for the WPSM54G Print Server utility?  Version 1.1 available on Linksys website does not work with the version of the firmware 1017.  I cannot locate my original CD and prefer do not update the firmware I'm running 1017 and everything works fine.

  Thank you

  In fact, I found my CD so I'm all set.

• Problems with basic setup and split tunneling VPN

  I created a SSL VPN in an ASA CISCO ASDM 6.6 8.6 running.
  IM able to connect to the VPN and reach all the devices with the LAN but I am not able to browse the web. When I activate the tunnel split Im able to browse the web, but then Im not able to reach any internal device.
  Here is part of the show's run:

  network of the RedInterna object
  150.211.101.0 subnet 255.255.255.0
  Description Red Interna
  network of the NETWORK_OBJ_10.4.1.0_28 object
  subnet 10.4.1.0 255.255.255.240
  inside_access_in list extended access permitted ip object RedInterna all
  Standard access list VPN_INTERNET allow 150.211.101.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  management of MTU 1500
  local pool VPN_POOL 10.4.1.1 - 10.4.1.14 255.255.255.240 IP mask
  failover
  secondary failover lan unit
  failover lan interface GigabitEthernet0 fail-1/2
  key changeover *.
  failover interface ip fail-1 10.3.1.21 255.255.255.252 watch 10.3.1.22
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 66114.bin
  enable ASDM history
  ARP timeout 14400
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.4.1.0_28 NETWORK_OBJ_10.4.1.0_28 non-proxy-arp-search to itinerary
  !
  NAT source auto after (indoor, outdoor) dynamic one interface
  inside_access_in access to the interface inside group
  Route outside 0.0.0.0 0.0.0.0 187.217.68.145 1
  Route inside 10.0.0.0 255.0.0.0 10.1.1.78 1
  Route inside 150.211.0.0 255.255.0.0 10.1.1.78 1

  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-win-3.1.00495-k9.pkg 1
  AnyConnect enable
  tunnel-group-list activate
  internal GroupPolicy_VPN_ group strategy
  attributes of Group Policy GroupPolicy_VPN_
  WINS server no
  value of server DNS 8.8.8.8
  client ssl-VPN-tunnel-Protocol
  dominio.com.MX value by default-field
  type tunnel-group VPN_ remote access
  attributes global-tunnel-group VPN_
  address VPN_POOL pool
  Group Policy - by default-GroupPolicy_VPN_
  tunnel-group VPN_ webvpn-attributes
  enable VPN_ group-alias
  !

  I m don't know if Im missing a few small details or Setup. Any help will be much appreciated.
  Thank you!!!

  Hello

  When you use full VPN Tunnel (which is the default setting), you will have a number of things that you need to configure on the SAA.

  First, the ASA by default will not allow traffic to enter via an interface and then exit through the same interface. It is essentially, what happens when the customer VPN traffic comes to the ASA and then heads on the Internet.  In your case the traffic goes through the 'outside' and leaves via the 'outside' interface.

  You will need this command

  permit same-security-traffic intra-interface

  You can check if their licence at the moment with the command

  See the race same-security-traffic

  Second, VPN users will need to have the NAT configuration like all users LAN behind the ASA real. So you basically configure dynamic PAT for 'outside' to 'outside' traffic

  You can get there with the following configuration

  network of the VPN-PAT object

  subnet 10.4.1.0 255.255.255.240

  dynamic NAT interface (outdoors, outdoor)

  I suppose it should do for you to be able to connect to the Internet and the LAN when the VPN is active.

  Hope this helps

  Let me know how it goes.

  -Jouni

• Problem transfer Adobe Creative Suite from old computer to new computer. Any ideas how to fix?

  A couple of weeks ago, I bought a new MacBook Pro. I was told that I would be able to transfer the Adobe Creative Suite to my new computer from my old using an external hard drive that I bought at the same time. I was able to transfer the applications via, however, when I try to start to use the program, I get an error "Setup." Any ideas on how to solve this problem?

  Avoid transferring. Adobe software must be reinstalled from scratch with a valid serial number.

  Download applications download Creative Suite 6

• Optimized for Chromakey video recording mode?

  Hi people,

  I am a moderately fluent user of Adobe Premiere Pro (I have CS4 at home and use CS5.5 at work), but I'm just my feet wet with a greenscreen Setup. I shot some footage of test yesterday, using the Panasonic HDC-TM90. The camera can shoot 1080/60 p, or a variety of modes AVCHD. I turned my test images AVCHD [HA] (1920 x 1080 17Mbps/VBR) mode.

  After the first film, I used the color key effect to remove the background, but found that there was some severe enough blur on the hands of my subject, which resulted in green showing through the blurred image, resulting in turn in his hands more or less disappear.

  Unfortunately, my company just bought this camera, so I don't have the opportunity to get a better camera, and I have to do with what I have. My understanding is that the 1080/60 p in shooting mode will reduce or eliminate motion blur, but (if I understand it well), I'll need to re - encode the video to something like 720/60 p to make it compatible with various playback devices.

  So my question is, someone has experience with this, and can they recommend a process or a method of shooting? If I pull the 1080/60 p, first and work my magic chromakey, the image will look like poor after re-encoding?

  My apologies if these are stupid questions - as I said, I'm just getting started with this stuff, and I'm under the gun to get this project finished. Thanks in advance for any help.

  PC Glenn

  Shoot 720 p 60 at higher transmission speed.

  And Ultra key is the right tool.

• Final Cut Pro - sound level (EBU r128)

  Currentl, I work for a good balanced "Loudness" EBU r128-standard project in Final Cut Pro. I was surprised that I wasn't able to find audiometers for verification and/or balancing tools / normalize the sound level.

  Any tipps?

  I know: just the fact that I wasn't able to find it's not and the indicator because "he is not here." But if she's not here, why is it called 'final' cut?

  Kind regards

  #JoPhi

  read excellent Ronny suggestions in this thread:

  http://www.FCP.co/Forum/4-Final-Cut-Pro-x-FCPX/22706-R128-LUFS-in-FCPX

• Install Firefox 31 extracted, then crashes

  Hi people,
  Long time user. New problem. So I downloaded full version (not the heel) V31 V29 would not update. Whenever I ran the installer, it would show the progress bar 'Extraction', then a windows message: "Firefox Setup has stopped working" and the follow-up report:

  Signature of the problem:

   Problem Event Name:	APPCRASH
   Application Name:	setup.exe_Firefox
   Application Version:	1.0.0.0
   Application Timestamp:	4bc06cda
   Fault Module Name:	ntdll.dll
   Fault Module Version:	6.1.7601.18247
   Fault Module Timestamp:	521ea8e7
   Exception Code:	c0000005
   Exception Offset:	0002e3be
   OS Version:	6.1.7601.2.1.0.256.48
   Locale ID:	3081
   Additional Information 1:	4c0d
   Additional Information 2:	4c0d4d78887f76d971d5d00f1f20a433
   Additional Information 3:	4c0d
   Additional Information 4:	4c0d4d78887f76d971d5d00f1f20a433
  

  I tried:

  • Remove entirely FF29, program files, then the hidden folder data/Mozilla/Firefox
  • Run Malwarebytes, CCleaner, reboot (W7Pro64)
  • Leave the network for local HARD disk Setup

  Any suggestions appreciated and TIA.

  Quick update - 32 Firefox installed no problem

• Failed to load money microsoft on Equium A60

  Hello. I have an equium A60 and when I try to install microsoft money, it says that it cannot operate while the toshiba keyboard shortcut properties are running! How can I activate the shortcut keys off (not that I want to do), but, if not, how can I get setup! Any suggestions greatly appreciated!

  Please see this topic that has been placed in this forum there is a little time ;)

  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=1476

  I think this should help you.
  Please post again if it will work.

• HP 500-046: 6 beeps at startup, can't access boot options (black screen) but then Windows loads ok

  After making a system image backup I wanted to test the recovery disc. To start from the cd tried to change bios to disable secure boot and enable legacy startup.  Could not get the pc to boot once so reset cmos by shorting the pins on the mboard.  Now to start always get 6 beeps and black screen, but after a minute, windows login screen lights up and it works fine.  Unable to access the bios Setup screen any key used at startup.  6 beeps indicates a video card problem, but no material error in device mgr points.  Want to update to Win 10, but unsure about do to address this problem starting.  Appreciate any help.

  @JohnN59,

  Thanks for the information to know.

  You can try the DVI port on the motherboard

  I/o Ports and internal connectors

  Rear i/o ports

  Figure: IO back panel

  

  1. USB 2.0: 2

  2. Output S/PDIF port optical

  3. VGA

  4. DVI - D

  5. LAN

  6. USB 2.0: 2

  7. USB 3.0: 2

  8. Audio: Port of central/subwoofer (yellow-orange)

  9. Audio: Rear Speaker Out port (black)

  10. Audio: Side Speaker Out port (gray)

  11. Audio: Line (light blue) port

  12. Audio: Output line port (lime)

  13. Audio: Microphone (Pink) Port

  If is not shows the start then try the Bios reset/recovery (windows + B key).

  Please keep me updated.

• Tecra M2V crashes during the Windows 2000 format

  I'm working on the installation of Windows 2000 for a laptop Tecra M2V in my school. The installation process crashes when the disk has reached 6% format. It is always in the same place that the deadlock occurs. Is there a way to get around this, or can I change a setting in the bios Setup? Any help appreciated.

  Hello

  Not easy to say what can be the problem, but if the formatting process always freezes at the same place I assume that there is a problem with the HARD drive sector faulty or bad. I recommend you to check the HARD drive using a tool. Google a bit and you will find many tools for free.

  Good bye

• Satellite C660 - TouchPad freeze at startup

  Hi I'm new and this is my first post so please be gentle!

  I have a Satellite C660 with windows 7 purchased as a refurb factory it is my 1st laptop, I have a problem after startup, and everything loaded on my desktop, it seems that if I use my TouchPad too early it freezes, he did it since I bought it, but I thought it was me being not used to a touchpad and the "bloatware" to start is the only way I can get the pointer to move if I have a finger from the top to the bottom of line scrolling to the right of the TouchPad horizontally or diagonally, it moves very slowly until I can be open and close a browser window, the file or even the startup window, then it will then act as usual and do not freeze again for my entire session If I leave it for five minutes at the start, it works fine, sometimes it will freeze also out of standby or hibernation, but not always.

  OK, I thought maybe it was the necessary driver update I checked in Device Manager and it said it was working properly but that of course is when the pointer is as it should be, in the Device Manager if I pilot of the touchpad/driver/update and internet search it tells me I have the drivers updated If I choose to search for a driver on my computer/let pick me from a list of device drivers that I have the following:-

  Mouse Compatible PS/2
  Synaptics PS/2 Port Compatible TouchPad
  Synaptics PS/2 Port Compatible TouchPad
  Synaptics PS/2 Port TouchPad

  I should have all those showing? can someone with a file of similar specifications check that for me please?

  strange thing is that if I go to TouchPad properties via the taskbar, and then click driver all options except the driver Details are grayed out and done, I can open two windows of TouchPad properties from the device and the task bar manager and have them on the screen at the same time.

  Some things I should mention are a mouse in the usb works fine, I stopped a lot of the "bloatware" and would help the useless stuff running at startup, hoping that I have disabled the function of locking of the click on the TouchPad, sound as it needs to be "warmed up" to run correctly when running properly it works fine without problem as the laptop came pre installed and only Disc I have is the recovery one create you the initial Setup!
  Any help would be appreciated!

  Hello

  First of all, I don t think that this problem is related to the installed touchpad driver but if you wish, you can install the latest touchpad driver available from the European driver Toshiba.

  Visit the European driver Toshiba page and choose:
  Computer laptop Satellite Satellite C series Satellite C660 driver Touchpad

  Now you should get all the touchpad driver available for C660 series.
  I found the driver for the touchpad Synaptics for Win7 32 bit and 64 bit.
  The latest version seems to be v15.2.11.1

  I think you should go to Panel of-> Software
  Check here if Synaptics touchpad driver appear in the list of installed software.
  If so, uninstall the present.
  Then, download and install the Synaptics v15.2.11.1 driver

  The touchpad settings could be changed in Control Panel-> mouse-> tab advanced-> button Advanced.

• Corruption of memory NVRAM Possible Z580

  Hi guys ~!

  Since the last time I posted here, I got my Wi - Fi adapter and cable replaced LCD, my warranty is far beyond being expired and... Well, I had a new problem here.

  Some background first:

  After realizing that lenovo support in Poland is as - somehow totally new to be terrible, useless and cause more problems than it's worth (finally), I ended up approaching my laptop with my own skills in computer repair - parts is not free but at least I'm getting somewhere, right?

  September 12, 2014, I flashed my BIOS to remove the white list and got an adapter Intel Wi - Fi (5100 AGN) as a replacement for my broken Atheros who becomes completely useless at this point, and all I could do was throw it.

  After flashing the BIOS, I noticed that the entry of start menu the menu of Novo pointed to the configuration of the BIOS, while everything else was basically just to boot the os of the 1st player. I do not much since I always access to the BIOS, so that I can start all the cool stuff I had on my USB with no problems.

  I tried to update my Windows 10 for new construction, April 11. The process seemed to get stuck at some point given - I managed to read a book while waiting then... you know. So I tried force-restart of my camera and...

  Well...

  * beep *.

  Question:

  I can't access BIOS Setup by any means, or the Start Menu. I'm with Secure Boot UEFI enabled mode, about default settings. Remove the HARD drive got stuck on the blank screen. Of course, I can boot any player USB in this way (it's how I restored my Windows 10, I just did a clean install of USB). I wish I had this two guys back without replacing the motherboard if.

  What I tried:

  I used efibootmgr to check that if the UEFI entries are still there-, so they're doing efibootmgr magic will not help.

  I tried to do a BIOS update using a lenovo site utility, but I got an error checking - I think maybe it's because I got my BIOS modded-whitelist.

  I tried this weird thing with removal of all sources of power and pressing the button for 30 seconds, which probably eliminated the CMOS - no effect.

  I suspect corruption NVRAM, based on what I found on the Internet - although it occurs mainly on Samsung devices (perhaps, Phoenix BIOS, this is not a bad trail).

  And please, don't suggest me to contact lenovo support, simply read the entire post first - my warranty has already expired, I cancelled in waaays maaanyyy so there is no way that they could help me and I think that buying a new motherboard and replacement of the stuff myself cost me lenovo doing much less do it for me - even though I don't want to Since I can live with this problem, really.

  Basically, I answer to myself (STILL ALOOONEEE), but in any case, I thought that this could be useful for someone.

  Remove the battery CMOS did the trick, I can now access the BIOS Setup. List of entries is always a little weird, but I think this must be just a bug in this mod white list, not that it never worried me anyway.

• small runtime for more recent versions of labview?

  A few times in the past, I created simple LabVIEW autonomous executibles.  I did this in 8.6 and used minimum duration Engine Setup instead of the full version.  This resulted in a size of 30-35 Meg installation package.

  Agin need to create a simple executable, but have not seen a minimum setup for any version of LabVIEW 8.6

  Are there minimum runtimes for other versions?

  The runtime default 2014 is Meg 264!  It is difficult to explain to a client why a simple "Hello World" program requires a 200 Meg download.

  Jack Dunaway has documented a way to segment the execution engine, basically only, including parts which you need.

  https://connect.wirebirdlabs.com/knowledgebase/articles/172999-segmenting-the-run-time-engine

  And this is a point of exchange of idea about that.

  http://forums.NI.com/T5/LabVIEW-idea-exchange/segment-the-LabVIEW-run-time-engine-RTE-to-only-necess...

• Pinmap a module SCXI-1302 missing links?

  Hello

  I use a unit of SCXI 1000 with a Board of 1180 and a terminal of 1302. I searched if the database of help on the pinmap for the 1302, but I get to "error: you are not authorized to view this document" even when I'm logged.

  examples:

  http://forums.NI.com/T5/LabVIEW/SCXI-1302-pinout/m-p/579610?requireLogin=false

  http://forums.NI.com/T5/signal-conditioning/wiring-of-SCXI-1302-terminal-block/m-p/481491?requireLog...

  I want 8 channels of analog inputs on the Board for 8 pressure sensors. Measurement & Automation Explorer, I should connect the PIN 34 to 68, but it has only 50 pins on the 1302. I can't find the track of the PIN for my setup. Any help would be appreciated.

  It seems that I just find the answer to my own question.

  It is for those who have the same questions I had.

  The 1302 has a pinmap according to this file that I found some time ago, but only just re-found yet. This is a map showing the task of the PIN, the version of 68 pins and PIN the 50 version.

  Sorry for the post. I always seem to find things five minutes too late.

• PRO-100 network settings

  I just got my Pro-100 and set up, but I can't figure out how to get the network settings. I printed the network configuration page and it shows that my ethernet is disabled. Where can I enable and whee do configure ethernet and wifi settings? I have install all software provided on the CD, and I can't find anthing that connects me to these settings. It is currently connected through the USB port, but this is not how I want to connect. Frustrating!

  Just use the Canon IJ Network Tool to change your settings.  Let him find the printer, select the printer port, click the configuration tab.  Here you select the wired lan connection and have the choice to give up or let the printer get the IP address automatically.  In my system, my assigned IP printer is 10.0.0.3.  I found assigning printers in the better router and ports (wired and wireless) Setup and any changes in the automatic allocation of router messed with my configuration of printer port assignment.

  If you have installed the drivers both 8-bit and 16-bit, you may need to verify that the port assignments have the same address.  I don't remember if I had to assign in the two ports, but better to be safe.