has broken the plastic hinges that hold the keyboard connectors - x100e - corrections? solutions?

Similar Questions

• Equium 80 - 132 has PSA87E - the LCD connector pinout

  Can someone help me or direct me to a site (if not here :)) where I can find the pinout of the connector from the motherboard to the LCD from a satellite
  with
  model name: EA80-132
  Model No.PSA87E - 0030069K

  Hello

  I tried to find all the manuals but unfortunately without success. If you search for the connector on the motherboard where you can plug the display cable, it should be placed somewhere in the middle. When the keyboard is removed check connector in the upper mid position (tails).

  Sorry, but I wasn't able to find any nice document with screenshot. In any case I hope that you will be able to find the right connector.

• Portege R500 - replacement of the keyboard - success

  After buying a new keyboard for the R500 on EBay about a year ago, I finally blew the courage to replace a badly scratched by a new keyboard. The reason I've waited? I was worried about how to get out the old keyboard (it is locked down to the chassis, and it was obvious that I have would hurt one during the withdrawal.

  There is a nice write-up general on how to disassemble a R500 here:
  http://www.irisvista.com/tech/laptops/Toshiba-Portege-R500/disassemble-laptop-remove-hard-drive.htm

  The description above is not to discuss the keyboard however, so here's some additional information and tips:

  * Read this whole procedure before you start - it's simple, but not for the faint of heart.

  * Shut down, unplug the power, remove the battery.

  * Make sure that you have the correct keyboard for your model. The US keyboard is p/n G83C000903US for example. One I removed was a Rev 1 and a new one, I had a Rev 2 (don't know the difference - they look identical). They can get as low as $40-mais check the part number before you buy.

  * The keyboard connector is located under the computer, and so you will have to take off from the bottom, carefully following the instructions in the link above.

  A couple of notes: (a) the cable Ribbon PCMCIA connector must be opened to disconnect the cable, as this is the only thing that prevents you from removing the bottom of the computer. You can easily do so through access memory on the back door, but BE careful not to damage the cable lock. It works by switch to the top the little plastic lever that is held in place by small pieces of plastic on the sides of the connector that flex * a little *. Be gentle with this connector. When you put it back later-connector, if you placed the cable all the way into the connector, you can lock with only slight pressure down on the connector, and it will snap into place.

  (b) there are other types of cable Ribbon connectors use too. For example, to unlock the keyboard connector, now visible also on the bottom of the deck, slide both ends of the connector in the direction where the cable plugs in. They are snug and will only move about 1/4 ", be gentle but firm.

  (c) the two tiny connectors blocks free access to the water of the keyboard do not have locks on them. We're a band with only a few drivers, and one is a red and white power connector. Just pull out them. All the other connectors, you will probably miss through requires unlocking, so be careful!

  _Now back to the keyboard: _

  Once you have managed to disconnect his cable on the bottom, turn the laptop and start to remove the keyboard on the edges. It is supported by many small pieces of sticky tape, 2 faces, and that's it. As the base of the keyboard is made of aluminum, it is likely that you will distort the keyboard a bit as release you it, even though it may be downplayed maybe using a tool like a rule or something plastic and pry with it. Take care of not to damage the connector of the Ribbon and try to ignore these scary cracking sounds that identify each section!

  Once you have turned it off, you must remove any excess tape before starting point and again put a bunch of small pieces of new, good quality 2-sided tape (such as 3 m). No need to use anything stronger or thicker - just put a bunch of parts everywhere on the base, especially near the edges and the space key.

  Now, finally, turn the keyboard in position, making sure that you screw the connector back Ribbon through to the correct place. Turn the laptop over and re - insert and lock the Ribbon connector (make sure that it is directly and fully forward lock connector). All other connectors back in too. Then come back and push down hard on all sections.

  Re-assembling, taking care to put the 4 mm and 6 mm screws in the right places and a tiny on the side.

  Cross your fingers and turn it on!

  Good luck!

  Thank mate for this review.
  Generally the replacement of keyboard is not really complicated and someone with small technician skills should be able to replace it

• I need to change the keyboard on Tecra M5

  Hello

  I need to change the keyboard on a tecra m5.
  Unfortunately, this is not mentioned in the manual how to do this.

  Please advice.

  Thanks in advance for your help.

  Best regards
  Wim Gijsels

  Hello

  I think that it s not mentioned in the manual, because I should only be made of professional technicians for laptop

  In any case, a friend of exchanged me the keyboard and told me to remove the keyboard first support. Who s the plastic cover between the keyboard and LCD display. So open the LCD screen and use your fingers on both sides and lift the keyboard bracket. There are two screws that attach the keyboard under the door-keyboard. Remove the two and lift the keyboard. Last but not least remove the keyboard plate to remove the cable from the keyboard connector.

  As you can read it's not that complicated and I hope I could help a bit! :)

• Qosmio G20: How to replace the keyboard

  DOES ANYONE KNOW HOW TO REPLACE THE KEYBOARD ON A QOSMIO G20?

  Hello

  I m not an owner of the Qosmio G20, but the replacement of keyboard on the G20 is very similar to another series of laptop.
  If you want to remove the keyboard please follow these steps:

  1.) open view.
  2.) Insert your finger into the slot between the reinforcement of the keyboard and the computer. Then,
  Lift the keyboard bracket to unlock and remove.
  3. remove 1 screw from the keyboard hold the plate.
  4. remove the screws fixing the keyboard
  Lift the upper part of the keyboard and turn down the palmrest.
  6. remove the 2 screws of the plate support keyboard and remove the
  keyboard support plate.
  7 disconnect the cable from the keyboard connector on the system board CN3200.
  8. remove the keyboard.

  All that s

  But note; If you have no experience, please don t remove the keyboard.

• Unable to release the keyboard cable in Omnibook XE2

  Hello world

  This is my first post here and it's probably going to be a silly question but I am a novice when it comes to disassemble the laptop so I thought I might as well ask people who know better things that I don't want to spoil anything.

  I have this old Omnibook XE2 I started to disassemble but got stuck because I cannot remove the keyboard connector cable. The Service Manual shows both sides of the cable and then gently pull upwards, but it won't come out this way. Happens a little when I shoot, but I pull hard enough and I fear I'm going to break something. I thought there might be a lock or a clip that must be open to pull the cord, but as I've never done this before, I am a little hesitant on how to do it.

  I enclose a few photos so you can see what the connector looks like.

  

  

  Any help is appreciated.

  See you soon,.

  Laszlo

  Hello lackua,

  You must unplug the Ribbon for the keyboard cable.

  You will need to remove the base plastic too; It should be part of the Ribbon.

  I would like to know how everything goes.

  Nice day.

• I can't get my keyboard connector cable to go into the slot

  I am trying to replace my Macbook Pro 17 "keyboard of the computer after a most unfortunate incident of beef broth. I installed the new keyboard but cannot get the keyboard connector Ribbon to enter the bus connector. I lifted the barrier of pinching the back connector and others, but when I try to move the Ribbon connector will not ride in any fair and other kinks in the opening. Rather than throw across the room as I am currently considering is anyway to run the cable into the connector, so I can lock the bar top and finished the replacement?

  It of a disassembly of your MacBook, look there:

  https://www.iFixit.com/teardown/MacBook+Pro+17-inch+unibody+teardown/618

• my c drive shows low disk space, so I searched for the program that holds more memory on drive c. I got to know that this pagefile.sys has 3 GB in the c drive

  Hi, my c drive shows low disk space, so I searched for the program that holds more memory on the c drive. I came to know that pagefile.sys has 3 GB in the c drive, kindly guide me to move the pagefile.sys to another drive.

  Hi jafrin.michel,

  Thanks for posting in the Microsoft community.

  Before you start the troubleshooting steps, I need the information required.

  What version of the windows operating system do you use?

  Method 1:

  If you are using windows 7, I suggest to perform a disk cleanup and verify.

  Delete files using disk cleanup

  http://Windows.Microsoft.com/en-us/Windows7/delete-files-using-disk-cleanup

  Method 2:

  If you want to move the pagefile.sys to another drive, follow the steps and check out them.

  Follow these steps to move the pagefile.sys to C: drive on D: drive (if you have the drive D :).

  1, write click on my computer and select Properties.

  2, click on the Advanced tab.

  3, click settings under performance menu.

  4, click on the Advanced tab and click on change.

  5, select letter (C :) and "BOLD" No pagefile then click on Set. )

  6, if you want to configure pagefile.sys in, select drive D: drive letter D: and "BOLD" in the custom size or the size of the system managed , then click on Set. It displays a pop-up message click OK.

  7, again click apply and OK OK.

  8, the system you will be asked to reboot, click on Yes.

  9, after rebooting the system, you can see the pagefile.sys will be moved to D:

• Broke the plastic connector that holds DVD Ribbon on the motherboard

  Hello

  I got my new Alienware M14x open and looked at the DVD player when I accidentally broke the plastic connector that keeps the ribbon cable to the connection on the motherboard. This is the connector that holds the zero insertion force (ZFI) on the tablecloth.

  It was a negligent act on my part, and I take responsibility.

  Is it possible to buy this small plastic connector? I have no part number. I do not use my DVD player at all and looked out swapping for a HARD drive. To do this, I need the connector to the ribbon cable can be connected to the motherboard.

  Any help would be appreciated.

  I managed to solve this problem without using the original part.

  See the post, http://en.community.dell.com/support-forums/laptop/f/3518/t/19600130

• The Web Acceleration Client error (513) - internal error of the Web acceleration Client has detected an internal error that caused the connection between the accelerometer of the Web

  The Web Acceleration Client error (513) - internal error
  The Web acceleration Client has detected an internal error that caused the connection between the customer to accelerate Web and server acceleration Web to be broken. A new attempt of the web page may correct the problem.

  I get this error at all times when working in the ancestry.com Web site. I have to reload the page on almost every search I do on this Web site. It is the site of the ONLY I get this error message, can run uninterrupted for several hours on other sites and never get this message. I talked to the people at Ancestry.com support and they did 2 recommendations: turn antivirus (did not help) or switch to another web browser. I tried both 11 IE and Chrome Version 31.0.1650.63 m and I have no problem with either of these 2 browsers this error.

  Is there a problem with the way Firefox and ancestry.com communicate?

  Hello byron.lewis, many site problems can be caused by corrupted cookies or cache. To try to solve these problems, the first step is to clear cookies and cache.
  Note: This will be you temporarily disconnect all sites, you're connected to.
  To clear the cache and cookies to do the following:

  1. Go to Firefox > history > clear recent history or (if no Firefox button is displayed) go to tools > clear recent history.
  2. Under "Time range to clear", select "all".
  3. Now, click the arrow next to details to toggle the active details list.
  4. In the list of details, see the Cache and Cookies and uncheck everything.
  5. Now click the clear now button.

  More information can be found in article to clear your cache, history, and other personal information in Firefox .

  This solve your problems? Please report to us!

  Thank you.

• My ipod 5th generation is stuck by resetting the settings and I tried holding the power and the "home" button but has just the same. Also, I tried to sync it upward, so I tunes but it has not been recognized and I can't answer on my ipod. Help, please!

  My iPod 5th generation is stuck by resetting the settings and I tried holding the power and the "home" button but has just the same. Also, I tried to sync it upward, so I tunes but it has not been recognized and I can't answer on my iPod. Help, please!

  Try the remaining shares of:

  - iOS: do not respond or does not light

  -Also try DFU mode recovery mode post-test

  How to put iPod touch / iPhone in DFU "Karthik doodles."

  -If failed and that you cannot completely turn completely the iOS device, leave the battery to drain completely. After loading a hour repeat the foregoing.

  -Try a different cable

  -Try on another computer

  S ' there is still not successful that usually indicates a hardware problem and an appointment at an Apple store Genius Bar is in order.

  Shop Apple Store - Genius Bar

• W520 has a broken key on the keyboard. Where to repair?

  W520 has a broken key on the keyboard. Where to repair? It has been bothering my OCD a lot. In addition, my lenovo laptop is still under warranty. Would I be able to get this fix for free?
  Thank you!

  Good day and welcome to the community.

  As you mention that you are still under warranty, I would recommend that you call the Service (info below) to discuss the issue.

  Kind regards.

• The item 'xuiexi.scr' that this shortcut refers to has been changed or moved, so this shortcut no longer works correctly

  Original title: problem with the shortcut "xuiexi.scr".

  When I try to open my files I get a notice that says: PROBLEM WITH SHORTCUT.  The item 'xuiexi.scr' that this shortcut refers to has been changed or moved, so this shortcut no longer works correctly.  You really want to remove this shortcut?  YES / NO

  What can I do to recover these files.
  Thanks in advance for any help.
  NW

  Hello

  (1) remember you to make changes to the computer before the show?

  (2) is that limit this issue when opening specific programs?

  You can perform the following methods.

  Method 1: I suggest you to run the Microsoft Fixit article.

  Fix broken desktop shortcuts and common system maintenance tasks: http://support.Microsoft.com/mats/system_maintenance_for_windows/en-us

   
  Method 2: Run Virus Scan

  You can download Microsoft Safety scanner, which provides on-demand scan, and remove viruses, spyware and other malicious software. It works with your current antivirus software.

  See the link below to download Microsoft Safety scanner on the system.
  http://www.Microsoft.com/security/scanner/en-us/default.aspx
  Note:
  The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.
  WARNING:
  The data files that are infected can be cleaned by removing the file completely, which means that there is a risk of data loss.
   
  It will be useful.

• AutoCorrect has learned the word that breaks down when it is typed iOS 10

  I've been using iOS for more than five years, it seems that my library for automatic correction has become corrupted at least for a specific name entry 'Toni smith' I

  Whenever I type the employees name AutoCorrect changes this name string to something that freezes the iOS and iPad all crashes recently I turned off auto correct - dictionary - predictive parameters and it is solved.

  ID like to use once again, AutoCorrect is their way to change a setting in the scholarly dictionary?

  At first, I thought it was just a keyboard problem, but then I went to the dictation and every time at the end of the dictation. Once again the crashes of iOS it happened in Facebook, ios e-mail and enamel with frozen then similar results to crash.

  How to reset my dictionaries through all my idevices. Happening now on ipad and iphone

  Settings > general > reset > reset the keyboard dictionary

• I have a complaint on my Mac Book Pro. I bought my computer in January 2016 and it has two problems: the first is the display of the retina that has many traces of the keyboard and as many times it freezes. I have looked for help on the local Apple Store

  I have a complaint on my Mac Book Pro. I bought my computer in January 2016 and it has two problems: the first is the display of the retina that has many traces of the keyboard and as many times it freezes. I have looked for help on the local Apple Store and support too, but it did not help. I would like you help me solve this problem.

  Thank you.

  Kelly

  Your machine is still under warranty, so you should take it to your local Apple store for repairs. Function late in January, you bought it, you still have phone without support. If you can't find any help on the Apple Store, then I don't know what you expect to find here. We have no way to check for problems you have described or any additional hardware, etc.