Help setting up a VLAN to the physical network

Similar Questions

• Unable to bridge the physical network in Workstation 7 server

  Hello

  Newbie here. I looked through forums here and can see that some people have had issues trying to fill (VMnet0) virtual machines to physical networks. Not sure if someone came up with a definitive answer, so I'll add my scenerio to the mix.

  I implemented WMware Workstation 7 on a Windows 7 boot camp partition on my iMac and created a network of 3 Win 2 k 3 servers, a Win 2 k 8 Server, a client Win XP and Win 7 for the test. These are connected to a local network called LAN 1 and resident in an area properly.

  I'm trying to set up internet connectivity to network through the first win 2 k 3 server. This server has two network adapters - one on LAN 1 and a bridge to my netgear router. I configured my router to reserve an ip address for the server (192.168.0.5) and manually configure internet/bridge the NIC server with this ip address.

  I can't do a ping to the router (192.168.0.1) the Win 2 K 3 server and also my iMac (192.168.0.4) virtual machine. Can also ping the server of my iMac.

  I'm limiting my internet on the server tests to see if the machine alone can access the network before I try to configure the other machines to access.

  Have seen a few suggestions of uninstall, reinstall the bridge of VMware for the physical network card Protocol, but also to restore the properties by default Virtual Network Editor - I made two suggestions, still unable to connect to the network. Also changed the setting "filled in the ' in the virtual network to the physical network, bridge auto setting map editor.

  In the settings of the server vm, the machine has a list of two network cards - a set jumpered to the physical network, the other to connect to LAN1.

  Interesting thing is that the original image (vmware machine used as a model) is always set to NAT and is able to connect to the Internet.

  Spend about 6 hours to try a variety of ideas and get back on my feet, but I think that everything is as it should.

  Is there a bug in Workstation 7 or y at - it a step that I missed?

  Any ideas would be most appreciated!

  shadowalka wrote:

  Virtual machine:

  IPv4 routing table
  ===========================================================================
  List of the interface
  0x1 ........................... MS TCP Loopback interface
  0 x 10003... 00 0c 29 66 51 df... Intel(r) PRO/1000 MT Network Connection
  0 x 10004... 00 0c 29 66 5 b df... Intel(r) PRO/1000 MT Network Connection #2
  ===========================================================================
  ===========================================================================
  Active routes:
  Network Destination gateway metric Interface subnet mask
  0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.5 10
  0.0.0.0 0.0.0.0 192.168.61.2 192.168.61.2 10
  127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
  192.168.0.0 255.255.255.0 192.168.0.5 192.168.0.5 10
  192.168.0.5 255.255.255.255 127.0.0.1 127.0.0.1 10
  192.168.0.255 255.255.255.255 192.168.0.5 192.168.0.5 10
  192.168.61.0 255.255.255.0 192.168.61.2 192.168.61.2 10
  192.168.61.2 255.255.255.255 127.0.0.1 127.0.0.1 10
  192.168.61.255 255.255.255.255 192.168.61.2 192.168.61.2 10
  224.0.0.0 240.0.0.0 192.168.0.5 192.168.0.5 10
  224.0.0.0 240.0.0.0 192.168.61.2 192.168.61.2 10
  255.255.255.255 255.255.255.255 192.168.0.5 192.168.0.5 1
  255.255.255.255 255.255.255.255 192.168.61.2 192.168.61.2 1
  Default gateway: 192.168.61.2

  
  ===========================================================================

  The W2K3 prompt, which should act as a router must have a default gateway configured to point to the physical gateway you. In case you, it points to itself. It is a dualhomed machine and it must only have set up a default gateway, remove the gefault gateway that manages the connection 192.168.61.0.

  AWo

• Two VLANs in the same network bubble?

  Hi all!

  I do not know very well of networking, and don't know my VMware network guy, so I hope that someone here might be able to answer my question. Thank you!

  I'm testing the conversion of some of our production servers. Since they have the same name, they are all in a bubble of network on the same host. So I have a vSwitch called "Bubble Network Test" which has several virtual machines, but who doesn't have an uplink (no associated physical map). So far, this has worked very well. So that users to test, I also have two XP machines to also live in this bubble. However, we will have performance issues. In our test of D/R one a few months ago, we found that the application performed very bad when the customer was in the same VLAN as the server; change the client to a VLAN different fixed performance.

  So, I would do it here in the hope that it will improve performance. However, I do not know how to do it. Can anyone offer any tips/advice on how to have more than one VLAN in the same network bubble? I have to make two vSwitches and then connect them somehow?

  Thank you!

  As long as you stay internal to the ESX Server then Yes you will need virtual switches - you will have then a virtual machine that will span two switches, acting as a router routing traffic between VLANS.

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• How to set of Cluster nodes on the same network but on different gateways

  Hello
  We want to set of Cluster nodes on the same network but the connection through different gateways for Unicast (WKA). We strive to add sockets for < cluster-config > tangosol-coherence - override.xml file, pls help how to set.

  Looks like you are using the default configuration for the system property:

  8088
  true

  The probable reason for this question, it's the localport is unaffected as 8088 for communication on the machines. Either use the property system - Dtangosol.coherence.localport = 8088 and - Dtangosol.coherence.localport.adjust = false or see the node will connect and find node assigned to each node and open the nodes; recommended to use multiple addresses node as in unicast configuration below:

  well-known-address >
  
  
  

  XXX
  
  8088
  
  
  
  YYY
  
  8088
  
  

  See you soon,.
  Neeraj

• virtual network card to the physical network mapping and default loadbalancing

  What Virtual Machine virtual network card is map physical NIC.

  For example.

  lets assume Vswitch1 on host1 esx dedicated for the network of the virtual machine (port group) and it has 6 cards network linked to it (vmnic1, vmnic2, vmnic0, vmnic3)

  Load policy (default) Balancing - from the originating virtual port (it balances only outbound traffic through all the nic assigned to vswitch1 right?)

  ESXi host1 <-Vswitch1 (the VM network) <---(vmnic 0-vmnic 3)

  Lets assume that esxi hosting 6 virtual machines and each virtual machine has two network cards configured.  Through some documents, come out of that when the virtual machine is running, it gets connected to the ports of availabe on virtual swicth. say, I turn on the virtual machine in the order VM1, VM2... VM6.

  Vmname virtual adapter port on virtual switch1 Mapping of the physical network adapter                        

  VM1 eth0, eth1 1.2 which mappeed of the physical NIC to eth0, eth1?

  VM2            eth0,eth1                              3,4                                      ?

  VM3            eth0,eth1                              5,6                                      ?

  VM4            eth0,eth1                              7,8                                      ?

  VM5            eth0,eth1                              9,10                                    ?

  VM6            eth0,eth1                              11,12                                  ?

  Since we use load balancing based on the virtual port, can two virtual map of the same virtual machine are mapped to the two physical NETWORK card I want say eth0 VM1 is mapped to the (physical nic) VMNIC0, VM1 eth1 get connected VMNIC1 (physical nic).

  It would be great if you could explain how the virtual network adapters are mapped to the physical NIC Y at - it a command or a script to the list NIC(of all vms hosted on esxi) virtual NETWORK adapter mappings physical in detail.

  .

  sansaran wrote:

  Is there a way to know what virtual NIC to connect to which physical NIC

  With the virtual NETWORK adapter, you hear the virtual card inside the VM? If if and when you use several VMNIC like you, there is no visibility in vCenter (usually vSwitches, we see with Distributed vSwitches).

  However, you can use the command-line ESXTOP tool in the view 'n', for the connection between the virtual machines and the outgoing vmnic.

• Best way to make the physical NETWORK card-&gt; vmnic number?

  Is there a known way to understand the link between the vmnic0, vmnic1... logical names and their relationship to physical network cards of ESX/ESXi? In other words, if you get on a new server with, say, 6 physical ports and a config on one vmnic, how do you know which translates to correct physics?

  The means that I can think of are:

  • Check the MAC address within vSphere Client, but then you must somehow know the MAC of the physical NETWORK adapter

  • check the number of PCI of vSphere Client, but this seems a bit difficult to understand?

  • fix pull cables and are looking for "plugged" or not.

  So, how do you do this, if necessary?

  In fact, it is quite easy to see which port on a teddy bear refers to things in the VMware environment...

  Look under configuring the host tab/Server/network element equipment adapters... This will show each NIC and what vmnic # are assigned to the ports. It will also show the MAC address of each port. If they are assigned to vSwitches, it will also show this info...

  

  You can also see the Networking section (still under the Configuration tab) to see the vmnic # assigned to each vSwitch...

  

  Multiport NIC generally have markings on the plate PCI to let you know which is which... All you really need to know is what is the beginning of numbering.

  VMware VCP4

  Review the allocation of points for "useful" or "right" answers.

• Help setting up a banner on the 25 theme

  Hello
  I managed on the basis of set up a banner on the 21 theme, but the theme 25, it doesn't work.
  
  App: 103
  [http://fam-erp.com/apex/f?p=103:3:3178558156212 url:] Example of work on the topic 21
  
  App: 131
  [http://fam-erp.com/apex/f?p=131:3:7074920954842:NO url:] Does not for example the 25 theme
  
  [url http://fam-erp.com/i/images/fam/documentation/index.html] Banner docs
  
  Can you please take a look:
  
  http://fam-ERP.com/Apex
  Workspace: test
  user: test
  PWD: test
  
  Best regards
  Fateh

  Fateh says:
  Hello
  I managed on the basis of set up a banner on the 21 theme, but the theme 25, it doesn't work.

  App: 103
  [url http://fam-erp.com/apex/f?p=103:3:3178558156212:] Example of work on the topic 21

  App: 131
  [http://fam-erp.com/apex/f?p=131:3:7074920954842:NO url:] Does not for example the 25 theme

  [url http://fam-erp.com/i/images/fam/documentation/index.html] Banner docs

  Can you please take a look:

  http://fam-ERP.com/Apex
  Workspace: test
  user: test
  PWD: test
  What is a plug-in for + {: identifier of the thread = 2462853} +?

  Great idea in the pile of "jQuery is not an object" error messages JS (you want always to the JS console?). Plug-in scripts have been included in the page model before the standard APEX/jQuery scripts. Reduced to an error "undefined is not an object" when they have been moved after them. Can't come up with something more on an iPhone on a bus...

  Published by: fac586 on December 3, 2012 18:10

  No, the score for debugging to jQuery with an iPhone on a bus 22. Same problem as in previous discussions: lose jQuery.noConflict () during the initialization of the plug-in...

• Configuration of multiple VLANs on the Campus network up to 800 users

  Hi all

  I design a network for our client who has a campus network to:

  currently: 250 users, near future Expansion (3Months): up to 650 users; Future users of 1000 Expansion(6_Months):upto

  There are various services such as students, teachers, Admin, accounts & WiFi. Now they have HP/3Com switches all connected in a single broadcast domain.

  Now, to put the differnet deptts. in different VLANS, I plan to physically initially isolate them & use a multilayer Cisco switch only the basis for the configuration of VLAN for each Department. This way the used switches will simply serve as switches access (no config necessary).

  The new switch will be connected to a WAN/Internet router already in place i.e. of 1841.

  Please Q) suggest a switch appropriate in this regard, t manage users (from 250 to 1000)? such as a 3500 or 3700.

  Q2) given that most of the user groups will be connected on the separate Uplink port on the new switch, what is the level of redundancy should we have? that is, only the redundant power supply is enough or we will have 24 port switches QTY: 2 for full redundancy?

  Q3) can we have different connections of VLANS on a single switch uplink Port, & more switch can make the difference on the basis of the subnet ID?

  Q4) Im not sure how I connect WiFi access points that are installed as independent flanges at the moment? They should also be connected to the trunk on the new switch Port of VLAN?

  We will also have a domain controller, Server Server & Proxy DHCP on the network that will be connetected on the port of Siwtch (trunk) to serve all the VLANS.

  Kind regards

  Re-

  Hi Tek,

  Please see the below comments for your plan and hope that will help you.

  Please Q) suggest a switch appropriate in this regard, t manage users (from 250 to 1000)? such as a 3500 or 3700.
  I suggest you to go with 3750 24 ports switch (if your budget is ok then go with future expansions seen 4506)

  Q2) given that most of the user groups will be connected on the separate Uplink port on the new switch, what is the level of redundancy should we have? that is, only the redundant power supply is enough or we will have 24 port switches QTY: 2 for full redundancy?

  If you need redundancy of the connection between the switch access and distribution, please go with STP where you will have a pathname (physical connection) active and a different path (another physical connection) is pending.

  Q3) can we have different connections of VLANS on a single switch uplink Port, & more switch can make the difference on the basis of the subnet ID?
  Yes, if you have configured this port as a trunk port who wear all the VLANS on the trunk and you can assign the vlan desigered to the specific physical port.

  We will also have a domain controller, Server Server & Proxy DHCP on the network that will be connetected on the port of Siwtch (trunk) to serve all the VLANS.
  You can have DHCP to assign IP addresses to computers in the vlan specific by adding the command to support ip under the vlan specific.

  Please note the useful messages.
  Kind regards
  Nasri.

• VM network transfer speeds are two times faster than the speed of the physical network

  My stats from the server:

  HP Proliant ML110 G6

  Intel Xeon X 3440 @ 2.53 GHz

  8 GB RAM

  1 Gigabit NIC onboard

  1 PCIx dual port Intel Gigabit NIC

  1 1 to Seagate HARD drive (for virtual machines and ISO storage)

  4 1 to HP 7200 RPM hard drives

  ESXi 5.5 U2

  Network:

  Belkin AC1200 F9K1113v4 Gigabit router

  Computer:

  Sony Vaio i5 2440 M, 8 GB, 5400 RPM HDD

  The main objective of the ESXi server should be used as a NAS, but with the additional ability to run Windows or Linux VM casual as a game server.  I currently have Open Media Vault controls 1 to 4 hard drives in a configuration RAID10 of software with a plugin SMB/CIFS to provide access to the shares through the windows.

  Network management is through the card on board.  OMV uses its own port on the Intel network card.

  The problem:

  Transfers of networks (upload) to my Windows 7 PC to NAS OMV are slow (average 40MBps).  Playback speed (downloads) of SIN is about 100 Mbps, which is decent.  I tested the disk write speed using the hdparm since the console command, and they are all on average 110 - 130 Mbps.  Why is my computer so slow transfer speeds?  Is there a setting to ESXi which limits my network connection?

  Some things I noticed:

  If only I start a computer Windows 7 virtual on ESXi VMNetwork, my transfers from the Windows 7 VM to the NAS VM on average 105 MB/s, while the playback speed is around 90MBps.  If I could get my physical network to transfer at these speeds, it would be satisfactory.

  Can someone help me?

  Hello

  I presume that the OMV is the culprit here. See for example this discussion: http://forums.openmediavault.org/index.php/Thread/5507-Extreme-slow-samba-speeds/

  You may be able to resolve the server Samba inside the OMV.

  cykVM

• How can I associate the virtual machine to the physical NETWORK card?

  Hello

  I have a host, has two physical network adapters.

  I want to use one for VM and give an ip address for this but I do not know how to configure it. In my view, "Manage virtual networks" fuction for this...

  Thank you!

  You should already have a phyiscal WHAT NIC assigned to VMnet0 (bridged). So if the choice as vonnection for a guest. Create a second connection open by assigning the physical NIC then to VMnet2, for example (VMnet1 is already in use). Assign this connection to the second guest.

  AWo

• Need help setting bios to boot from the cd. I did already but the laptop does not start again for cd player.

  Hello

  I forgot that my administration windows log password after the holidays.  I have loaded down a free program called Ophcrack and had set my laptop to boot from cd 1 but I just cannot get the laptop to boot from a cd.  He just continued boot from the internal hard disk.

  The cd is an image and it is bootable on my desk.

  The model of laptop: laptop HP ENVY m6

  Product number: C2N77UA #ABL

  BIOS version: F.25

  Processor type: Intel Core i7-3632QM CPU @ 2.20 GHz

  OS: Windows 8.1

  I only did a password reset disk (I'm learning the hard way now!).

  I don't want to do a "System Recovery" because I have some data on it.

  I realize there are paid there password recovery tools windows, but I would like to use this 'free' program to try to break 1.

  I just need help / instructions to set the bios for laptop can be started from a cd.  I also tried to boot from a key USB but the laptop kept begin its internal drive.

  Help, please.  Thanks a ton!

  Ted

  Hi Ted,

  You are welcome

  Boot into the bios menu and go to the very section where you have disabled the Secure Boot.

  Find an entry called materials and this value to Activate.

  Save the changes and exit the bios.

  Follow the previous procedure below:

  Insert the bootable disc of Ophcrack and laptop stop.

  Tap away at the esc you key start Notepad to open the Start Menu.  Select boot options ( f9 ), use the arrow keys to select the CD/DVD drive and press ENTER.  You can also get a prompt to "Press any key to" continuous - it if requested.

  Kind regards

  DP - K

• Help setting up Dial-Peer in the CME

  Hello experts,

  I tried to set up my network voice for 2 days but no luck.

  Here is my scenario:

  CUCM

  CME

  IRIS PBX

  +++ Posted inside Config.

  CME and PBX are PRI resources; I can see active layer 1 and Layer 2 multi_Frame_Established in 'display the ISDN State '.

  SIP trunk of CUCM to established CMF.

  Cannot communicate registered CUCM to analog phones in PBX Voip phones.

  Several times analog voip calls work and then some changes in the PBX, which in fact shit once again. (Those that have been made by PBX technician)

  VoIP ext: 1003

  Analog position: 270

  !! for voip analog calls

  In CUCM:

  Routing model: 9XXX--> to the trunk of the CME

  In the CME:

  The destination model: 9... --> E1 card (with auto stripping)

  !! for analog / voip calls

  In PBX access code 4 and stripped when sending guys.

  that the means to post analogue for reach 1003 user consist 41003 and 4 will be stripped.

  In the CME:

  The destination model: 1... --> session target ipv4:

  With this configuration in the 'debugging ccapi inout"see"transfer number is NULL"and

  in the "show history of last calls 1" am see reason code "1 c" - invalid number.

  After some research, this are my ideas but not tested:

  1. I have incoming dial Exchange files corresponds to the movement of e1 card:

  voice pots Dial-peer X

  incoming called-number. T

  (2) I have to configure dtmf-relay-notify sip and dtmf-relay rtp - nte to accept the numbers of telephone service.

  (3) need to create any DIDs for incoming calls to pbx?

  Please help me on this point, how could I get from analog to voip calls and vice versa, which I think is fair? If this is not the case, what would be the alternatives? where we should use the dtmf-relay command. ?

  Thanks to all in advance.

  Current config:

  type 0 1 e1 card
  network-clock-participate wic 1
  network-clock-select 1 E1 1/0/1
  primary-qsig ISDN switch type
  voip phone service
  h323 connections allow h323
  allow connections h323 to SIP
  allow connections sip h323
  allow sip to sip connections
  no service additional h450.2
  no service additional h450.3
  Fax protocol t38 ls-redundancy version 0 0 hs-redundancy 0 help none
  SIP
  Registration Server expires max 600 min 60
  no update-callerid
  !
  voice class codec 1
  preferably 1 codec g729br8
  codec preference 2 g729r8
  g723ar63 preferably 3 codec
  g711ulaw codec preference 4
  g711alaw preferably 5 codec
  !
  controller E1 1/0/1
  No.-CRC4 framing
  time intervals PRI - Group 1-31
  !
  Voice-port 1/0/1:15
  Capitalization in the carrier speech
  MGCP
  MGCP behavior considered range tgcp only
  MGCP comedia-role behavior no
  disable the behavior MGCP comedia-check-media-src
  disable the behavior of MGCP comedia-sdp-force
  !
  profile MGCP default
  !
  !
  !
  !
  Dial-peer voice 3 pots
  destination-style 9...
  port 0/1/1:15
  !
  Dial-peer voice 1 voip
  destination-model 1...
  session target ipv4:10.15.108.242
  !
  !
  !
  !
  access controller
  Shutdown
  !
  !
  phone service
  MAX conferences 8-6 win
  transfer full-consult system
  !
  !

  OK, lets delete all of your peers-Dial and start from scratch.

  For testing purposes, we will test with specific numbers.  We can get more general thereafter.  Try the following tips for incoming traffic.

  voice pots Dial-peer 10

  / / DESC # incoming Iris PBX #.

  incoming called-number.

  direct line to inside
  Forward-digits all the

  Then lets try this for your Call Manager Dial-Peer

  Dial-peer voice voip 20

  destination-model 501

  session protocol sipv2

  session target ipv4: CUCM_IP

  If please retest and propose some outputs fresh showing.

  debugging ccapi inout voice

  ccsip debug messages

  Debug ISDN q931

• Need help setting dyed on bullet in the head

  My main activity is professional head shots.  I made hundreds of them, but this one has me stumpted.   The skin tones are as pale as a ghost, and for the life of me, I can't face this lady looks good (shades of skin that is... lol).    I usually use Digital Photo Professional, which is a Canon program that works great to set the skin tones and color temperature.  But this time it just happens no matter what I do.

  Can someone help me out here?   I can send the file raw on you unless they allow that in these forums, but I'm not sure.  You can post a raw here file?  In any case, thanks for the help. Or am I being too picky?

  ?

  

  I believe that the remedy is more modeling than to color. In the above example a duplicated layer has been added.

  Then, the Image > Image apply to the Source set to green string and normal blending Mode.

  Then, in the layers panel change the blending mode to luminosity and to flatten the Middle your modeling use slightly curves as shown.

  At this point, you have more flexibility to adjust the color of the image, if you wish. (I suggest a slight increase in yellow through less blue - not shown here)

  (You can also reduce the opacity of the light chain, if you prefer the effect. It has not reduced in the picture above).

• I need help setting up and I use the webcam.

  Original title: sex cam on my samsung r540
  I don't know how to get my web cam on my screen (samsung R540) to work what am I did or didn't do is not right.

  Hello

  1. which version of the operating system are you using in the computer?
  2 did you do changes on the computer before the show?
  3. you receive an error message?
  4. who is the manufacturer of the Webcam?
  5 is it a built-in or external webcam?

  You can download the drivers for the webcam from the following link by browsing the product and install it on the computer:
  http://www.Samsung.com/us/support/

• How to get the name of model of the physical network adapter

  I can see the template information for my network via vcenter card, but need help with registration this info for powercli.

  for example, that I'm looking for my request to have this output:
  "Broadcom Corporation NC370i Multifunction Gigabit Server adapt."

  Hello, jstroehmann-

  How about something like:

  ## get the .Net View objects for all of the host systemsGet-View -ViewType HostSystem -Property Name,Config.Network.Pnic,Hardware.PciDevice | %{    ## store pipeline variable for later use    $viewHost = $_    ## for each PhysicalNic on the host, output a bit of info    $viewHost.Config.Network.Pnic | Select @{n="HostName"; e={$viewHost.Name}},Device,MAC,@{n="NicDisplayName"; e={$oPNic = $_; ($viewHost.Hardware.PciDevice | ?{$_.Id -eq $oPNic.Pci}).DeviceName}}} | ft -auto
  

  He catches the .net visualize the object of all the HostSystems, and then displays some info like hostname, VMNic name, its MAC address, then the full name you mentioned.  You could, of course, something with the release other than send it to Format-Table.  How does do for you?