Similar Questions

• Need help setting bios to boot from the cd. I did already but the laptop does not start again for cd player.

  Hello

  I forgot that my administration windows log password after the holidays.  I have loaded down a free program called Ophcrack and had set my laptop to boot from cd 1 but I just cannot get the laptop to boot from a cd.  He just continued boot from the internal hard disk.

  The cd is an image and it is bootable on my desk.

  The model of laptop: laptop HP ENVY m6

  Product number: C2N77UA #ABL

  BIOS version: F.25

  Processor type: Intel Core i7-3632QM CPU @ 2.20 GHz

  OS: Windows 8.1

  I only did a password reset disk (I'm learning the hard way now!).

  I don't want to do a "System Recovery" because I have some data on it.

  I realize there are paid there password recovery tools windows, but I would like to use this 'free' program to try to break 1.

  I just need help / instructions to set the bios for laptop can be started from a cd.  I also tried to boot from a key USB but the laptop kept begin its internal drive.

  Help, please.  Thanks a ton!

  Ted

  Hi Ted,

  You are welcome

  Boot into the bios menu and go to the very section where you have disabled the Secure Boot.

  Find an entry called materials and this value to Activate.

  Save the changes and exit the bios.

  Follow the previous procedure below:

  Insert the bootable disc of Ophcrack and laptop stop.

  Tap away at the esc you key start Notepad to open the Start Menu.  Select boot options ( f9 ), use the arrow keys to select the CD/DVD drive and press ENTER.  You can also get a prompt to "Press any key to" continuous - it if requested.

  Kind regards

  DP - K

• I need help setting up and I use the webcam.

  Original title: sex cam on my samsung r540
  I don't know how to get my web cam on my screen (samsung R540) to work what am I did or didn't do is not right.

  Hello

  1. which version of the operating system are you using in the computer?
  2 did you do changes on the computer before the show?
  3. you receive an error message?
  4. who is the manufacturer of the Webcam?
  5 is it a built-in or external webcam?

  You can download the drivers for the webcam from the following link by browsing the product and install it on the computer:
  http://www.Samsung.com/us/support/

• Need help setting up related content in HCM 9.1 PeopleTools 8.51

  I need help setting up related content in HCM 9.1 PeopleTools 8.51.
  I created a new service id in 'Set Related Content Service'. Its simple, it basically goes to google.com.
  Then I assigned Related Content for the Application Pages on the page «Manage the Configuration content to related» I'm my scenario, I've added it to the careers under the main menu.
  Then I went to the careers page, but the 'related information' link does not appear. How can I get this link to related information to appear at the top of the page/component?
  
  Thank you
  -Cory

  In order to get it work, there are a few basic server configuration requirements that you need in order to make it work.

  (1) define the field of authentication on the Web server
  (2) set the authentication of domain on the web profile
  (3) enable Single Sign-On

  The next in "My Oracle Support" document provides details on configuring content services.

  E-PORTAL: how to set up content related services. [984855.1 ID]

  In addition, here is a link to the PeopleBooks online that deals with the configuration of related content services.

  http://download.Oracle.com/docs/CD/E18083_01/pt851pbr0/Eng/psbooks/tprt/book.htm?file=tprt/htm/tprt20.htm#H3002

  In addition, there are also some know the limitations to the use of related content are different depending on the version of the tools you use.

  I hope this helps.

• Need help to open two images with the same file with different exposures on the screen at the same time in the Photoshop creative cloud (in previous versions we could open two images of the same nef (raw) file and then combine them on the screen with the

  Need help to open two images with the same file with different exposures on the screen at the same time in the Photoshop creative cloud (in previous versions we could open two images of the same nef (raw) file and then combine them on the screen with the move tool. They have become a composite of two layers which could be developed further with the mask tool.

  Hello

  Please go to the preferences > workspace and uncheck the option 'open the document in the tabs '.

  

  Now you can click on file and choose file > open and open the two images in two different windows which can be arranged side by side.

  Thank you

• I need help to unite 2 users on the same CC account, can someone help me?

  I need help to unite 2 users on the same CC account, can someone help me?

  Since this is an open forum, not Adobe support... you must contact Adobe personnel to help
  Chat/phone: Mon - Fri 05:00-19:00 (US Pacific time) <==> NOTE DAYS AND TIME

  Creative cloud support (all creative cloud customer service problems)
  http://helpx.Adobe.com/x-productkb/global/service-CCM.html

• I need help about illustrator. I have the portable version of CS6, install and won't let me open the program. I get the error: 1 I have windows 7

  I need help about illustrator. I have the portable version of CS6, install and won't let me open the program. I get the error: 1 I have windows 7

  Error code 1 is often associated with permission issues. Have you tried to install Illustrator in a new user account with admin rights? If you want to download CS6, here's how to get it through creative cloud: html http://helpx.adobe.com/creative-cloud/kb/download-previous-versions-creative-applications.

  Let us know how it goes.

  Concerning

  Stéphane

• All my photos are displayed such as BW because somehow I saved a preset to quickly develop and it records in BW.  This is for all of my photos.  Individually, I can cancel their but did need help how to get rid of the pre-selection, so he's going to defau

  All my photos are displayed such as BW because somehow I saved a preset to quickly develop and it records in BW.  This is for all of my photos.  Individually, I can cancel their but need help how to get rid of the preset then all photos of goes to Default or in the shot. Thank you

  Go to the develop module and highlight all the images in the film at the bottom of the screen. Enable automatic synchronization, and then click the reset button. To reset all the images in your camera default settings.

• Need help setting up WebUI for the Wireless Gateway

  I have problem installing a Web UI for my demo project.

  I just do temperature is a simple application of WSN on a node of thermocouple WSN-3121 and it logging on a RT NI 9792 wireless gateway.

  Then, I wanted to create a web user interface and display whats in the user interface of the gateway - see the project.

  SO I'm stuck with the web INTERFACE coming.  I tried to read as much as I can but I still don't know what I'm doing wrong.

  As far as I see it, I need to create a web service in the construction for my gateway specifications and place the gateway_main.vi like the vi to use.  Then build and deployment.  Once it happened, and I run the vi on the bridge, I created a Web user interface as shown in the picture, where it counts the the gateway web service using 192.168.0.16:8080 - that works very well.

  When I run the Web interface, it is just and expires.

  I am using LAbview 2010.  Help, please.

  Hello markza,

  Your approach using the Web user interface designer and understanding its use case is quite accurate, the question lies in the web service, you have deployed. The VI you build as web service, which is gateway_main.vi, while loops inside and so cannot be used as a web service. The reason for the timeout is that your user interface Builder application calls the web service LV2010 and is stuck there for waiting time loops to complete. Also, the data type of cluster is not supported in the user Web interface Builder, so you'd have to break up from the entrance of the time of picking for the node wireless in two separate digital inputs.

  I recommend creating a Subvi out of your code inside of the while loop inside gateway_main.vi. The Subvi must have two digital inputs to replace the cluster (as mentioned above) and do not have one of the Boolean inputs Start or Stop. Output would remain the same, that is, two doubles and a Boolean value.

  I would like to know if this is useful and if you have any other questions.

  Thank you!

  Dieudonné jgfcnbh

  The user of LabVIEW Web R & D interface generator

• I need help setting up my home network - windows vista.

  I need help to configure my network, I ave a laptop & hubby the computer w / dsl wireless rouuter. If I can get trhis to work, maybe we can work on the printer.

  Original title: help w / home network

  Hi Luvy,

  Thanks for posting your query in the Microsoft Community Forums!

  Looks like you need information to set up home networking on the windows vista computer.

  We're here to help and guide you in the right direction.

  -What is the number of brand and model of the computer?

  I suggest you to return the items online help and check if it helps.

  Setting up a network home

  http://Windows.Microsoft.com/en-in/Windows-Vista/setting-up-a-home-network

  Setting up a wireless network

  http://Windows.Microsoft.com/en-in/Windows-Vista/setting-up-a-wireless-network

  To install the printer on the network see Help below articles.

  Install a printer on a home network

  http://Windows.Microsoft.com/en-in/Windows-Vista/install-a-printer-on-a-home-network

   

  Share a printer

  http://Windows.Microsoft.com/en-in/Windows-Vista/share-a-printer

  It will be useful.

  Let us know if you encounter problems under windows in the future. We will be happy to help you.

• need help setting up mocrosoft send my friend uses netgear wireless rural upstate ny need help for incoming, outgoing server POP3 etc info...

  try to set up my microsoft email in my pc. I need to respond to the need help sbout incomeing craiglist.i and out going.

  I have no idea to find my server address. I use connect netgear wireless.

  Hello

  Looks like you need configure Windows Mail

  you need to configure your e-mail account windows mail with your ISP internet service provider

  They provide you with account settings you need to do

  Ask them to

  username
  password for your access broadband account / distance with them

  Server of incoming POP3 mail
  outgoing mail SMTP server

  and here's how to configure windows mail after getting the email correct account settings

  http://www.vista4beginners.com/Windows-Mail

• Need help setting up switch SG300-10

  Hello

  I bought a SG300-10 switch and configuration.

  I have a problem to set up it causes that I'm not really used to networking.

  what I set up at the moment is the VLAN.

  VLAN 2 - step my router it for internet access

  Vlan10 - is for my server and pc in my office

  VLAN 40 - is for the wifi of comments.

  I will use the mode switch layer 3 and I want to configure a DHCP server on the vlan 40 but I'm not very well how to do.  I activated the DHCP and created a pool of ip but how I assign on the vlan 40? and how to set up everything to go on the internet? If I followed the basic logic, I will put all my members of port of vlan 2, is that correct?

  IM new in the field of networking

  Thank you

  Hi Justin,

  Here is some basic information for the switch. With VLAN, it is tag VLAN and remove the brand VLAN. A package of UNTAG means in the package header, there is no VLAN ID. The switch will provide separate from the client connection based on the transfer of bridge table. Usually UNTAG VLAN is used for the client connection. A beacon packet contains the VLAN ID in the header. In general, tag packets is used between other network device. An access port is member of 1 VLAN that is not marked. A trunk (on small business product) port is a port that has 1 UNTAG VLAN (VLAN native) and has the ability to tag the VLAN extra.

  Some examples of configuration CLI for tag and remove the brand VLAN. Keep in mind, VLAN 1 is the default VLAN, therefore, unless you make sure, VLAN 1 will default.

  To create a VLAN 2 on your switch

  Configure the terminal

  database of VLAN

  VLAN 2,3,4

  This will create the VLANs 2, 3 and 4

  To configure an IP address to a VLAN

  Configure the terminal

  interface vlan 1

  IP 192.168.1.254 255.255.255.0

  interface vlan 2

  192.168.2.254 255.255.255.0

  interface vlan 3

  192.168.3.254 IP address 255.255.255.0

  interface vlan 4

  IP 192.168.4.254 255.255.255.0

  Keep in mind, VLAN 1 must have a static IP address before you assign any other VLAN an IP address, or the switch will "lock".

  To assign an access as a member of the VLAN 1 port

  Configure the terminal

  Article IG1 interface

  switchport mode access

  To assign an access as a member of VLAN 2 port

  Configure the terminal

  interface hi2

  switchport mode access

  switchport access vlan 2

  If you check the GUI you'll notice port 1 is "1u" and port 2 is "2u".

  To create a trunk and assign some VLAN-

  Configure the terminal

  interface IG3

  switchport mode trunk

  switchport trunk allowed vlan add 2

  In the GUI, you will notice 3 port will be "1u, 2 t".

  To configure a port to have a VLAN different other that 1 as it removes the brand on a chest.

  Configure the terminal

  interface IG4

  switchport mode trunk

  switchport vlan trunk native 2

  switchport trunk allowed vlan add 3.4

  On the GUI, it will show '2u, 3 t, 4 t'

  Now that we have fundamental port assignment of the road, you can work on DHCP and IP address management.

  When the switch is in mode layer 3, if there is an IP address assigned to a VLAN, it is a switch virtual interface (SVI). The IP address of the service VLAN as default gateway which connects to this VLAN. The switch can associate the pool DHCP IP interface created on the switch-based layer 3.

  Firstly, we must establish your first jump of the switch - the default gateway of the switch statement. If you have a router connected to the SG300 you must assign the SG300 default gateway, which is the IP address of the router.

  Configure the terminal

  Default IP gateway 192.168.1.1

  Then you can concentrate on your DHCP scope. To configure a server DHCP table here is an example-

  network IP dhcp pool PRODUCTION
  

  address 192.168.2.1 low high 192.168.2.253 255.255.255.0

  Infinite rental

  default router 192.168.2.254
  

  dns-Server 8.8.8.8
  

  This basic table DHCP said many things.

  The name of the table is the PRODUCTION, this can be anything you want.

  low address is the first IP address that is assignable in the pool while high address is the last

  infinite lease means that had not expired DHCP lease

  Router by default, it is the most important. It is the default gateway, that the switch will be assigned to the customer. This is very important if you want router between VLAN or upstream of the internet

  DNS server, this allows to resolve the name instead of having to use IP only.

  Now, if you connect to a computer that is enable DHCP where VLAN 2 is not marked, you should receive an IP address that is assigned by the switch on this computer. Notice that the pool is a number of address IP 2 VLAN. The definition of IP pool, this is how it will bind to one VLAN, by matching the subnet.

  Now, once you have all the basic configuration complete, as Marty says, depending on the capacity of your router, it will need to need to support VLAN tagging, interface sub dot1q OR, as Marty has said, it would need static route to allow to your additional subnet route on the internet.

  Hope this will help you get on your way.

  -Tom
  Please mark replied messages useful

• BlackBerry Smartphones Newbie needs help setting up email

  Hello world

  I've been the proud owner of a "BOLD" for about 48 hours now. This is my first Blackberry, so please bear with me.

  I need to set up my Yahoo email. I remember setting up front, but I deleted it as my allowance for the use of network (3 Australia) showed 2 MB roaming allowance, of which half was used in one day.

  I think that the e-mail message has been implemented via a browser page, but I can't go back to this page. The e-mail setup wizard seems to be to the establishment through BES which I did not. Does anyone know the address of the page?

  I also remember, when I chose the browser (not of Planet 3) I was taken in a BB page that showed several options of setting up various things. There were about 5 or 6 boxes grey listed above the other? Anyone also know the address of the page for this?

  Thanks for any help,

  Paul

  You also see a personal Email Setup on the device icon? If not try going into the Options | Advanced options | The host routing table. In this screen press press the button menu and choose to register now. See if you receive a message from check delivered to your device. Subsequently, reset the unit by removing the battery for 30 seconds. See if you have this icon now after restarting the device. If you still don't you can try setting up the account again on your carrier's Web site BIS to add return e-mail accounts?

  What options do you remember on this Web site? Try to go to mobile.blackberry.com on your browser and see if it's the page.

• Need help to provide a page for the Oracle PeopleSoft HCM on internet

  Hello

  I need help to provide that a page of Oracle PeopleSoft HCM on internet for vacancies may be available for recruitment. How can I provide a Peoplesoft Web page?

  TKS

  Bruno will read

  Of Peoplebooks

  Access to external Sites

  External candidates, by definition, do not have the nicknames PeopleSoft. To allow external users access to a site, you put a link to the site on a location such as your public Web site. The site definition includes a field to set the URL of this external link.

  Deployed in this mode, the instance of PeopleSoft to be accessed by external users must have the appropriate security settings to allow users to bypass the access code. In other words, a user who clicks on the link is not presented with a PeopleSoft signon pages but is instead signed the using a user ID generic comments so that the user can be taken directly to the candidate Gateway.

  If an external candidate allows a more inactive candidate gateway session that the timeout you set, the default system behavior is to provide a link to the login page of PeopleSoft with the visible invited user ID.  According to your logic of password, the guest user ID might be locked if the applicant tries in vain to connect. For more security and ease of use, replace the code page to a page that displays an appropriate message.   For example, to display a message that the session has expired and provide a link back to the bridge of the candidate.

  Development of Sites

• Need help setting up DB Link from my Oracle 11 g XE to SQL Server.

  Hello
  
  I am trying to create a link to DB from my Oracle 11 g Express Edition on a Windows XP computer to a SQL Server. Here are the steps I've done so far.
  
  1. creating and setting up a connection to the DB SQL Server ODBC. Baptized SQLSERVER. Authenticated by Windows.
  2. updated the listener.ora. See below.
  

  SID_LIST_LISTENER =
    (SID_LIST =
      (SID_DESC =
        (SID_NAME = PLSExtProc)
        (ORACLE_HOME = C:\oraclexe\app\oracle\product\11.2.0\server)
        (PROGRAM = extproc)
      )
      (SID_DESC =
        (SID_NAME = CLRExtProc)
        (ORACLE_HOME = C:\oraclexe\app\oracle\product\11.2.0\server)
        (PROGRAM = extproc)
      )
      (SID_DESC =
        (SID_NAME = SQLSERVER)
        (ORACLE_HOME = C:\oraclexe\app\oracle\product\11.2.0\server)
        (PROGRAM = hsodbc) 
      ) 
    )
  
  LISTENER =
    (DESCRIPTION_LIST =
      (DESCRIPTION =
        (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
        (ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))
      )
    )
  
  DEFAULT_SERVICE_LISTENER = (XE)

  3. updated the tnsnames.ora. See below.

  XE =
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))
      (CONNECT_DATA =
        (SERVER = DEDICATED)
        (SERVICE_NAME = XE)
      )
    )
  
  EXTPROC_CONNECTION_DATA =
    (DESCRIPTION =
      (ADDRESS_LIST =
        (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
      )
      (CONNECT_DATA =
        (SID = PLSExtProc)
        (PRESENTATION = RO)
      )
    )
  
  ORACLR_CONNECTION_DATA = 
    (DESCRIPTION = 
      (ADDRESS_LIST = 
        (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1)) 
      ) 
      (CONNECT_DATA = 
        (SID = CLRExtProc) 
        (PRESENTATION = RO) 
      ) 
    ) 
  
  SQLSERVER = 
    (DESCRIPTION =
      (ADDRESS_LIST =
        (ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT=1521))
      )
      (CONNECT_DATA =
        (SID = SQLSERVER)
      ) 
    (HS = OK)
  )

  4. copy C:\oraclexe\app\oracle\product\11.2.0\server\hs\admin\initdg4odbc.ora to C:\oraclexe\app\oracle\product\11.2.0\server\hs\admin\initSQLSERVER.ora and has changed. See below.
  

  # This is a sample agent init file that contains the HS parameters that are
  # needed for the Database Gateway for ODBC
  
  #
  # HS init parameters
  #
  HS_FDS_CONNECT_INFO = SQLSERVER
  HS_FDS_TRACE_LEVEL = off
  
  
  #
  # Environment variables required for the non-Oracle system
  #
  #set <envvar>=<value>

  5 restarted listener.
  

  C:\>lsnrctl stop
  
  LSNRCTL for 32-bit Windows: Version 11.2.0.2.0 - Production on 18-SEP-2012 11:33
  :51
  
  Copyright (c) 1991, 2010, Oracle.  All rights reserved.
  
  Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1)))
  The command completed successfully
  
  C:\>lsnrctl start
  
  LSNRCTL for 32-bit Windows: Version 11.2.0.2.0 - Production on 18-SEP-2012 11:33
  :54
  
  Copyright (c) 1991, 2010, Oracle.  All rights reserved.
  
  Starting tnslsnr: please wait...
  
  TNSLSNR for 32-bit Windows: Version 11.2.0.2.0 - Production
  System parameter file is C:\oraclexe\app\oracle\product\11.2.0\server\network\ad
  min\listener.ora
  Log messages written to C:\oraclexe\app\oracle\diag\tnslsnr\PHAILORTD000012\list
  ener\alert\log.xml
  Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1ipc
  )))
  Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=1521)))
  
  Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1)))
  STATUS of the LISTENER
  ------------------------
  Alias                     LISTENER
  Version                   TNSLSNR for 32-bit Windows: Version 11.2.0.2.0 - Produ
  ction
  Start Date                18-SEP-2012 11:33:57
  Uptime                    0 days 0 hr. 0 min. 3 sec
  Trace Level               off
  Security                  ON: Local OS Authentication
  SNMP                      OFF
  Default Service           XE
  Listener Parameter File   C:\oraclexe\app\oracle\product\11.2.0\server\network\a
  dmin\listener.ora
  Listener Log File         C:\oraclexe\app\oracle\diag\tnslsnr\PHAILORTD000012\li
  stener\alert\log.xml
  Listening Endpoints Summary...
    (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1ipc)))
    (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=1521
  )))
  Services Summary...
  Service "CLRExtProc" has 1 instance(s).
    Instance "CLRExtProc", status UNKNOWN, has 1 handler(s) for this service...
  Service "PLSExtProc" has 1 instance(s).
    Instance "PLSExtProc", status UNKNOWN, has 1 handler(s) for this service...
  Service "SQLSERVER" has 1 instance(s).
    Instance "SQLSERVER", status UNKNOWN, has 1 handler(s) for this service...
  The command completed successfully

  6. link of database created by using the following command.
  

  create database link sqlserver using 'SQLSERVER';

  7. test using
  

  select * from "dbo.mytable"@sqlserver;
  
  ORA-28545: error diagnosed by Net8 when connecting to an agent
  Unable to retrieve text of NETWORK/NCR message 65535
  ORA-02063: preceding 2 lines from SQLSERVER
  
  select * from dbo.mytable@sqlserver;
  
  ORA-28545: error diagnosed by Net8 when connecting to an agent
  Unable to retrieve text of NETWORK/NCR message 65535
  ORA-02063: preceding 2 lines from SQLSERVER
  
  select * from mytable@sqlserver;
  
  ORA-28545: error diagnosed by Net8 when connecting to an agent
  Unable to retrieve text of NETWORK/NCR message 65535
  ORA-02063: preceding 2 lines from SQLSERVER

  I followed the steps in this link but do not know where I was wrong. Someone can help me.
  
  http://www.DBA-Oracle.com/t_heterogeneous_database_connections_sql_server.htm
  
  Thank you
  Allen

  HS messages should go here: heterogeneous connectivity

  No problem with this type of installation.

  A glitch in your specific configuration

  >

  (SID_NAME = SQLSERVER)
  (ORACLE_HOME = C:\oraclexe\app\oracle\product\11.2.0\server)
  (PROGRAM = hsodbc)

  11 g, the executable file is dg4odbc.exe, so you have read PROGRAM = dg4odbc. (I could reproduce the error with wrong program setting).