Home-DOT1X authentication mode

Similar Questions

• "authentication control-direction in" CLOSED authentication mode

  Switch: 4510R-E, running a DEV version 3.6.0-based

  ISE: 1.2.0.899 patch 7

  Hi, I worked on a weird issue where some of my clients would pass through their IP address and the only way I could get it back was to spend their open port in authentication mode. I need to run in closed mode, because I change VLAN via MAB.

  I worked with TAC, and they suggested that add the command "authentication control direction in" in my config switchport (below). Couple tests Ive done, this seems to help. But I understand why. Isn't the direction-control a little command reduce to naught the principle of closed mode operation? That is, it allows a communication until the device is allowed. Thank you.

  interface GigabitEthernet2/18
  switchport access vlan 34
  switchport mode access
  switchport voice vlan 66
  events-the link status logging
  authentication event fail following action method
  action of death server authentication of the event allowed vlan 34
  action of death event authentication server allow voice
  living action of the server reset the authentication event
  the host-mode multi-auth authentication
  authentication order mab dot1x
  authentication priority dot1x mab
  Auto control of the port of authentication
  restrict the authentication violation
  MAB
  dot1x EAP authenticator
  dot1x tx-time 10
  service-policy input QoS-entry-policy
  Service-politique-accueil-port-sortie-strategie output QoS
  end

  I also need to use this command to preserve the authenticated devices. He was going on with a video surveillance system, which was an embedded Linux operating system. It's the MAB and because there was no transmission all noisy traffic (unlike a windows box) then the switch would not be able to reauth it as it had no mac address to auth, so show up with an 'unknown' in the MAC field.

  It allows essentially traffic flow out of the port. This active unit to receive HTTP traffic and respond, then the switch could auth it again once the device sent a frame.

  When you do a Show authentication sessions you will notice a Oper control dir: the two will pass to Oper control dir: in

• OIF & integration OAM as Authentication Mode

  Hello

  I have setup an environment following the doc integration with the Federation of identities - 11 g Release 2 (11.1.2) to configure Oracle Identity Federation for use in Authentication Mode.

  But I'm not able to get the OAM login page and the OIF log shows the error:

  [2013 09-11 T 14: 04:27.546 + 10:00] [wls_oif1] [ERROR] [FED-12064] [oracle.security.fed.controller.ActionStateMachine] [tid: [ASSETS].] [ExecuteThread: '1' for the queue: "(self-adjusting) weblogic.kernel.Default"] [username: < anonymous >] [ecid: 000E9GLO_Hq2ZND5RBL6id0002Ni00002W, 0:2] [APP: OIF #11.1.1.2.0] [URI: / fed/IIP/samlv20] Exception: {0} []

  java.lang.IllegalStateException: property has not been set: oam11g-login

  at oracle.security.fed.util.config.ErrorConfigProcessor.createAndLogPropertyNotFoundError(ErrorConfigProcessor.java:72)

  at oracle.security.fed.model.config.Configuration.getStringProperty(Configuration.java:178)

  at oracle.security.fed.eventhandler.authn.SelectAuthnEngineEventHandler.perform(SelectAuthnEngineEventHandler.java:117)

  at oracle.security.fed.controller.ActionStateMachine.processEvent(ActionStateMachine.java:141)

  at oracle.security.fed.controller.EventControllerImpl.processEvent(EventControllerImpl.java:118)

  at oracle.security.fed.controller.ApplicationController.publishEvent(ApplicationController.java:425)

  at oracle.security.fed.controller.ApplicationController.publishEvent(ApplicationController.java:451)

  at oracle.security.fed.controller.ApplicationController.publishEvent(ApplicationController.java:434)

  at oracle.security.fed.controller.web.action.ResponseHandlerContext.publishEvent(ResponseHandlerContext.java:83)

  at oracle.security.fed.http.flow.authn.PerformUserAuthenticationResponseHandler.perform(PerformUserAuthenticationResponseHandler.java:32)

  at oracle.security.fed.controller.ApplicationController.processServletRequest(ApplicationController.java:338)

  at oracle.security.fed.controller.web.servlet.FederationServlet.doGet(FederationServlet.java:142)

  at javax.servlet.http.HttpServlet.service(HttpServlet.java:707)

  at javax.servlet.http.HttpServlet.service(HttpServlet.java:820)

  Thank you.

  The problem is solved by the addition of the following property in the OIF configuration file.

  / user/authnoam11g

  Not sure why this property has not been set during the installation/configuration.

• Home Vista Safe Mode does not start correctly. What should I do about it?

  Hi, I was struck by an unknown number of bugs. I don't know how.  I ran my anti-virus software and could not find bugs. I tried to start in safe mode to run antivirus and Vista programs won't let me access Mode without failure. I turn on the computer, press F8 repeatedly until my options appear. I tried the Safe Mode and safe mode with networking Mode. In both conditions, Safe Mode begins to start. Crosses of approximately 42 drivers and comes to the black screen with the oversized arrow, then the computer restarts.  What can I do?  I can't access Safe Mode!

  Hello

  If you need search malware here's my recommendations - they will allow you to
  scrutiny and the withdrawal without ending up with a load of spyware programs running
  resident who can cause as many questions as the malware and may be more difficult to detect as the
  cause.

  No one program cannot be used to detect and remove any malware. Added that often easy
  to detect malicious software often comes with a much harder to detect and remove the payload. Then
  its best to be thorough than paying the high price later now too. Check with them to one
  extreme overkill point and then run the cleaning only when you are sure that the system is clean.

  It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
  the regular windows when you can.

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
  (If Rootkits run UnHackMe)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can
  Download it here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
  security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
  here or use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
  (viruses, Trojans, rootkits, etc.). who infected your computer despite safe
  what you have done (such as antivirus, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  http://OneCare.live.com/site/en-us/default.htm

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
  system files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Dot1x authentication with IP and Hub phone behind

  Hi all

  I have a question about the following scenario:

  If I ISE deployment with x endpoint license, I have the following configuration:

  ISE - Hub SW - phone IP - 4 connected devices

  I need to authenticate and profile of all 4 devices connected to the hub, but at the same time, I have no need to authenticate the phone using the ISE IP, since this will consume additional endpoint for the number of licenses, and I need overcome this scenario.

  From the point of view configuration, using "authentication host-mode multi-auth" will solve the problem for the devices connected to the hub, but how can I exclude the IP phone number of endpoint from the point of view of ISE?

  Thank you.

  Ahmad.

  That's right, but the only problem that you are experiencing is the ability to put 'data' devices on different VLAN. So if a computer caches and must have guest access, they will be placed on the same vlan as the first device that connects to it.

  Here are a few reference documents on this scenario.

  http://www.Cisco.com/en/us/docs/switches/LAN/catalyst3750x_3560x/software/release/15.0_2_se/configuration/guide/sw8021x.html#wp1347331

  Thank you

  Tarik Admani
  * Please note the useful messages *.

• Access to the private during authentication mode

  When I connect to a Cisco device, I'm prompeted enter name of user and password. Once authenticated, I need to enter the 'enable' command, then my password again in order to have access to privileged mode. I want to be able to go directly to the priv mode.

  My AAA configuration looks like this:

  AAA authentication login default group Ganymede + local

  AAA authentication login ciscoadmins group Ganymede + local

  the AAA authentication enable default group Ganymede +.

  AAA authorization config-commands

  AAA authorization exec ciscoadmins group Ganymede + local authenticated by FIS

  AAA authorization commands 1 default group Ganymede + local

  AAA authorization commands 15 ciscoadmins group Ganymede + local

  AAA authorization network default group Ganymede +.

  the Group ciscoadmins of network authorization Ganymede AAA +.

  On my ACS SE (ver. 4.1.4.13), I the user and group configured setting the same thing for the GANYMEDE section + with SHELL (exec) checked and controlled level PRIV and the value 15.

  I can get this working with RADIUS but failed with GANYMEDE.

  Does anyone have a solution for this?

  Thank you

  Keith

  Keith

  I believe that the question involves this line of the config:

  AAA authorization exec ciscoadmins group Ganymede + local authenticated by FIS

  It creates a list of method named for permission. IOS wants to see this list of method specified on your lines (or he wants to use the list of default method). I suggest that you include this line under the vty lines:

  authorization exec ciscoadmins

  or use this line in the section of the aaa:

  AAA authorization exec default group Ganymede + local authenticated by FIS

  HTH

  Rick

• issue of intrusion via CFMAIL authentication mod...

  Ok. I have a site of cf for a long time... Appears as in the old days, you could use little intrusion via cfmail tag with params as...

  < intrusion via cfmail to = "xxx".

  from = "xx".

  object = "xxx".

  Server = "xxx" >

  test

  < / intrusion via cfmail >

  but when you're working on a new mod site - NOW, it seems I need authentication more - with user and Pass as:

  Server = "xxx" username = "xxx" password = "xxx" >

  More information: in reality the MX mail is NOW on another server on the site of CF - then maybe this could lead to the necessary changes?

  Q: is it true?

  It really depends on your mail server.  Are they using the same email on its new server software as they did when he was on the same square as ColdFusion?  In addition, if you put the servername, username information and password in CF administrator, you shouldn't include in your tags.

  -Carl V.

• Commissioning: flashing, thick slider, f8 is not Vista Home Premium safe mode

  I tried a "hard reset" unplugging everything, remove the battery, hold the power button for 15, plug AC adapter / CC and start-up but no go. When I try to press F8 to change safe mode, it does not work and only Black w/flashing cursor.

  No other lights are blinking all the codes. I was able to hit F2 and enter the BIOS and ran that memory and the hard drive test, which both have past.

  Finally, when I try to press on, say f10 again and again, finally I get a tone loud for about 5 seconds and then after that, it makes this noise to hit any key.

  ?

  Have you tried to boot into the Vista dvd installation and run the Startup Repair tool? Information on the Startup Repair can be foundhere.  Matthew Arkin - moderator answers Windows - Microsoft Partner - Windows Desktop experience MVP - http://twitter.com/Microsoft_Cares - this forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

• Certificate authentication mode?

  I want to try to build a more secure LAN. I want that every client (with or without wire) to connect the network used a certificate not a username/password pair.

  But now, as I am a newbie, I don't know what to choose between GANYMEDE + and RADIUS. Because I have a Mac mini, RAY is perhaps more appropriate, but I don't know how to establish the certification authority.

  Any help or suggestion will be appreciated!

  More generally, we do this in the context of the implementation of a product as of Cisco Identity Services Engine (ISE). ISE uses 802. 1 x and has the ability to check clients for things such as a certificate during authentication / posture assessment / remediation process.

  Also, it acts as a RADIUS server, and can dynamically remove permission (CoA) change to the authenticator (i.e. switch or wireless controller) to control things like the assignment of VLAN client and everything you can apply access lists.

  Client side, a supplicant is used to interact with the authenticator. You can use native supplicants to OS X or Windows, etc, but we generally recommend use of the Cisco AnyConnect Secure Mobility client with its access network (NAM) Module, because it is much more complete for this purpose.

  You could also make 802. 1 x with certificate authentication and use an authentication server different backend (like a regular Cisco ACS or Microsoft Network Policy Server), but you get only basic authentication more vs rich functionality what ISE gives (although ISE is much more ;)).

  Take a look at this Youtube video for an example of setting up certificates of authentication on ACS:

  https://www.YouTube.com/watch?v=U7qWJ7bIMHA

• Authentication mode privilege using Ganymede for Cisco routers

  I'm trying to set up a test environment where I need to be able to be requested for both a user name and password entering mode mode exec on a cisco IOS router. I was told the only way to do is through Ganymede. But I didn't all these configuration on Ganymede options to put in right place. Someone has already done an installation like this before. I'd appreciate any help on this. Thank you.

  That's right, as I said in my previous post you can not accomplish what you're trying to do.  In IOS the username that you use to connect

  the router is ALWAYS used when you are in enable mode.  If you want to change the user logged in as you will need log on the

  router and log back in with the right user.

  -Jesse

• Trying to access C: I get various error messages. I tried to start with windows 7 Home premium safe mode

  I have several hard drives in my computer. Local disk C: is not available. Disks hard D; E; F; and G work without problem.                             Trying to access C: I get various error messages. I tried to start in safe mode, also tried to use the administrator user and still no luck.

  At some point, I'll get one of the following messages

  My computer ran fine until a week ago. I have I think some how disable the administrator account and disabled drive C:

  (1) error 0 event log x 081000202.

  (2) temporary files for users: (Sean-pc) are limited.

  (3) I need the net administrator authorization.

  (4) C: not available Windows\system32\config.cmd.exe

  Hello

  Problems with the drive in Windows may result from permissions problems, or even corrupt corrupted user accounts.

  1. What is the exact error message you get when accessing drive C?

  Method 1: I suggest you to activate the default Administrator hidden on the computer account and check if it helps.

  Try to activate the built-in Administrator account, follow these steps:

  a. Click Start and type cmd in the box start the search.
  b. in the list of search results, right click Guest and then click Run as administrator.
  c. When you are prompted by user account control, click on continue.
  d. at the command prompt, type net user administrator / Active: Yes and then press ENTER.
  e. type net user administrator , and then press ENTER.
  f. Type exit and press ENTER.
  g. disconnect from the current user account.

  Method 2: Try to take ownership of the drive and check to see if the same problem happens.

  a. right click on the drive and then click Properties.

  b. click the Security tab and then click Edit.

  c. do one of the following:

  ·         To set permissions for a user who is not listed under group or user names, click Add, type the name of the user or group, click OK, select permissions and then click OK.

  ·         To change or remove permissions for a user or an existing group, click the name of the user or group, select the permissions and then click OK.

  For more information, see the article below:

  What to know before applying permissions to a file or a folder:

  http://Windows.Microsoft.com/en-us/Windows7/what-to-know-before-applying-permissions-to-a-file-or-folder

  "Access denied" or other errors in the access to or work with files and folders in Windows: http://support.microsoft.com/kb/2623670

  Method 3: Check a drive for errors: http://windows.microsoft.com/en-US/windows7/Check-a-drive-for-errors

  Important: when running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost.

  For all windows questions do not hesitate to contact us and we will be happy to help you.

• How to restore the latest version of a laptop installed with the version of xp home edition authentic which is corrupt and ineffective at present.

  In the light of the announcement that the xp version support will be withdrawn w.e.f. April 8, 2014, I want to restore the B205 Toshiba laptop with the latest version to recover the notebook. Please suggest measures to be initiated at the end.

  Hello

  Here is the Vista Forums, not XP.

  There is no available from Microsoft Windows XP download.

  You can contact your computer manufacturer and ask them to send you a set of recovery discs, if it is still available.

  They should do this for a small fee.

  "How to replace Microsoft software or hardware, order service packs and replace product manuals.

  http://support.Microsoft.com/kb/326246

  And if you have never received a recovery disk when you bought your computer, there should be a recovery Partition on the hard drive to reinstall XP back on how you purchased your computer.

  The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

  Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

  Ask them to the proper key sequence.

  Toshiba is press 0 (zero) to start to start the process of relocation/restore to the way you bought in later operating systems.

  You will still need to install all of the SPs, updates, etc.

  See you soon.

• Domain user in dell FS7610 authentication mode

  Hello world

  I have configured my first FS Nas.FS 7610 7610 are integrated with PS Series equallogic and we reached FS7610 by Group Manager gui. Container and actions are created via the gui Manager, shares are available on the network, but we are only successful connect CIFS share with CIFS administrator account storage not the domain administrator account even if the FS7610 are joined with domain name must also know what to authenticate the domain user to share any CIFS.

  Thank you best regards &,.

  Ali Hassan

  Problem has been solved by entering a DNS entery...

• authentication dot1x some problom

  Hello

  helleo

  WO have a problom to dot1x authentication,

  When I enter the configuration of configuration of dot1x in the interface, interface to authenticate user in State of err - disable

  Here is the configuration of the interface
  interface FastEthernet0/45

  switchport access vlan 21

  switchport mode access

  the host-mode multi-auth authentication

  Auto control of the port of authentication

  MAB eap

  dot1x EAP both

  dot1x quiet-period of waiting 3

  dot1x tx-period 5

  spanning tree portfast

  Or authenticating switch failed newspaper

  n 4 16:52:16.381: % AUTHMGR-7-FAILOVER: failover "dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.381: % AUTHMGR-5-START: start "mab" for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.423: % MAB-5-FAIL: failure of authentication for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.423: % AUTHMGR-7-RESULT: authentication result 'no response' of 'mab' for the customer (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.423: % AUTHMGR-7-FAILOVER: failover "mab" for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.423: % AUTHMGR-7-NOMOREMETHODS: exhausted all methods of authentication for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:52:16.423: % AUTHMGR-5-FAIL: failed authorization for customer (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:53:17.165: % AUTHMGR-5-START: start "dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:53:21.376: % DOT1X-5-SUCCESS: authentication successful for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID

  June 4, 16:53:21.376: % AUTHMGR-7-RESULT: result of the authentication 'success' of 'dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:53:21.376: % DOT1X_SWITCH-5-ERR_ADDING_ADDRESS: cannot add the address on Fa0/45 AuditSessionID 0A51F11D000000266273D33D 2c41.380f.f187

  June 4, 16:53:21.376: % AUTHMGR-5-SECURITY_VIOLATION: security breach on interface FastEthernet0/45, new address MAC (2c41.380f.f187) is considered. AuditSessionID 0A51F11D000000266273D33D

  June 4, 16:53:21.376: % PM-4-ERR_DISABLE: error in security breach detected on Fa0/45, putting the Fa0/45 in State of err - disable

  June 4, 16:53:22.400: % LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/45, state changed to surviver 4 16:52:16.381: % AUTHMGR-7-FAILOVER: failover "dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.381: % AUTHMGR-5-START: start "mab" for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.423: % MAB-5-FAIL: failure of authentication for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.423: % AUTHMGR-7-RESULT: authentication result 'no response' of 'mab' for the customer (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.423: % AUTHMGR-7-FAILOVER: failover "mab" for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.423: % AUTHMGR-7-NOMOREMETHODS: exhausted all methods of authentication for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:52:16.423: % AUTHMGR-5-FAIL: failed authorization for customer (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:53:17.165: % AUTHMGR-5-START: start "dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:53:21.376: % DOT1X-5-SUCCESS: authentication successful for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID
  June 4, 16:53:21.376: % AUTHMGR-7-RESULT: result of the authentication 'success' of 'dot1x' for the client (2c41.380f.f187) on the Interface Fa0/45 AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:53:21.376: % DOT1X_SWITCH-5-ERR_ADDING_ADDRESS: cannot add the address on Fa0/45 AuditSessionID 0A51F11D000000266273D33D 2c41.380f.f187
  June 4, 16:53:21.376: % AUTHMGR-5-SECURITY_VIOLATION: security breach on interface FastEthernet0/45, new address MAC (2c41.380f.f187) is considered. AuditSessionID 0A51F11D000000266273D33D
  June 4, 16:53:21.376: % PM-4-ERR_DISABLE: error in security breach detected on Fa0/45, putting the Fa0/45 in State of err - disable
  June 4, 16:53:22.400: % LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/45, changed state down

  Looks like your scenario made to match a known defect

  CSCti69845 voilation took place after the success of fashion multi-auth auth

  Workaround

  Configure a vlan VoIP Multi-auth port (or)

  Address / solved in paragraph 12.2 (55) SE01

  Jatin kone
  -Does the rate of useful messages-

• 802. 1 x authentication and phones

  I have just begun to roll authentication of 802. 1 x and found that although I got the authentication for the PC the data VLAN to work, phones on the VOICE VLAN are not unless I put 'host-mode authentication' to 'stream '.

  We did turn not authenticated for 7 years with phones and both work of the PC.

  What I want to do (i.e. what management told me to move), is to have phones connect not authenticated (CDP agreeing to handle correct assignment of VLANS) but require PC to authenticate.

  I guess the simple question is; is it still possible? If this is the case, any advice is greatly appreciated.  (config switch is below).

  Thank you

  Arch

  !
  version 12.2
  no service button
  horodateurs service debug datetime localtime show-timezone msec
  Log service timestamps datetime localtime show-timezone msec
  encryption password service
  !
  switch to hostname
  !
  boot-start-marker
  boot-end-marker
  !
  emergency logging console
  emergency logging monitor
  enable secret 5 *.
  !
  AAA new-model
  !
  !
  Group AAA dot1x default authentication RADIUS
  !
  !
  !
  AAA - the id of the joint session
  clock timezone cst - 6
  clock to summer time recurring cdt
  1 supply ws-c3750g-24ps switch
  mtu 1500 routing system
  VTP transparent mode
  no ip domain-lookup
  !
  !
  interface ip igmp snooping mrouter vlan 41 item in gi1/0/27
  interface ip igmp snooping mrouter vlan 41 item in gi1/0/28
  !
  QoS omitted MLS
  !

  pvst spanning-tree mode
  spanning tree extend id-system
  !
  internal allocation policy of VLAN ascendant
  !
  VLAN 13
  name data - VLAN
  !
  VLAN 857
  name - VLAN VoIP
  !
  VLAN 1611
  name comments - VLAN
  LLDP run
  !
  !
  class-map correspondence AutoQoS-VoIP-RTP-Trust
  match ip dscp ef
  class-map correspondence AutoQoS-VoIP-control-Trust
  match ip dscp cs3 af31
  !
  !
  Policy-map AutoQoS-Police-CiscoPhone
  class AutoQoS-VoIP-RTP-Trust
  DSCP ef Set
  320000 8000 exceed-action of the police controlled-dscp-transmit
  class AutoQoS-VoIP-control-Trust
  DSCP Set cs3
  32000 8000 exceed-action of the police controlled-dscp-transmit
  !
  !
  !
  GigabitEthernet1/0/1 interface
  switchport access vlan 13
  switchport mode access
  switchport voice vlan 857
  security breach port switchport protect
  bandwidth share SRR-queue 10 10 60 20
  form of bandwidth SRR-queue 10 0 0 0
  queue-series 2
  priority queue
  authentication-sense in
  no response from the authentication event action allow vlan 1611
  stream of host-authentication mode
  Auto control of the port of authentication
  protect the violation of authentication
  MLS qos trust device cisco-phone
  MLS qos trust cos
  Auto qos voip cisco-phone
  dot1x EAP authenticator
  spanning tree portfast
  service-policy input AutoQoS-Police-CiscoPhone
  !
  interface GigabitEthernet1/0/2
  !
  interface GigabitEthernet1/0/3
  !
  interface GigabitEthernet1/0/4
  !
  interface GigabitEthernet1/0/5
  !
  interface GigabitEthernet1/0/6
  !
  interface GigabitEthernet1/0/7
  !
  interface GigabitEthernet1/0/8
  !
  interface GigabitEthernet1/0/9
  !
  interface GigabitEthernet1/0/10
  !
  interface GigabitEthernet1/0/11
  !
  interface GigabitEthernet1/0/12
  !
  interface GigabitEthernet1/0/13
  !
  interface GigabitEthernet1/0/14
  !
  interface GigabitEthernet1/0/15
  !
  interface GigabitEthernet1/0/16
  !
  interface GigabitEthernet1/0/17
  !
  interface GigabitEthernet1/0/18
  !
  interface GigabitEthernet1/0/19
  !
  interface GigabitEthernet1/0/20
  !
  interface GigabitEthernet1/0/21
  !
  interface GigabitEthernet1/0/22
  !
  interface GigabitEthernet1/0/23
  !
  interface GigabitEthernet1/0/24
  !
  interface GigabitEthernet1/0/25
  !
  interface GigabitEthernet1/0/26
  !
  interface GigabitEthernet1/0/27
  !
  interface GigabitEthernet1/0/28
  switchport trunk encapsulation dot1q
  switchport trunk allowed vlan 13,857,1611
  switchport mode trunk
  bandwidth share SRR-queue 10 10 60 20
  form of bandwidth SRR-queue 10 0 0 0
  queue-series 2
  MLS qos trust cos
  Auto qos voip trust
  !
  RADIUS-server host 10.1.2.10 auth-port 1645 acct-port 1646
  Server RADIUS 7 key *.
  RADIUS vsa server send authentication
  end

  Hello

  authentication with PC and phone needs "multi-domain of authentication host mode. You con use MAC address or 802. 1 X (username & password) for authentication of IP phone.

  Profile authenticatipo must send "device-traffic-class = voice" to the switch. PC fits the DATA cross-domain and phone VOICE-field.

  See attachment: