How can I stop Vista to boot into safe mode? Vista does not meet F8 when starting upwards.

Similar Questions

• How can I stop Vista Service Pack 1 download... its stuck at 83% and clicking stop installation does not work

  How can I stop Vista Service Pack 1 download?  I tried to download the service pack one and its deadlock in 83%...after 5 hours I hit stop installation, but it just gray out and don't stop - I'm afraid to restart because don't know what will happen.  Help, please... I think that probably Norton it stopped completely download so I'm cutting of norton, but nothing is happening because I think that the serivce pack is stuck in the loop.  Any advice would be greatly apprecaited.  Can I reboot? Can I go back to a restore point?  Thank you

  Hello

  This problem may be due to Norton or other software. You can restart the computer and check. If all goes well, you should be able to boot to the desktop without any problem.
  The error message in the event viewer can point to the program which caused this problem.

  Reference:
  Open event viewer
  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer
  What are the information in the event logs? (Event Viewer)
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-information-appears-in-event-logs-Event-Viewer

  You can download the latest service pack using the article below and verify if you are able to install it.

  How to obtain the latest Windows Vista service pack
  http://support.Microsoft.com/kb/935791

• my system does not start upwards - don't stop progression blue bar that goes round and round. I can boot into safe mode and safe mode with networking mode.

  my system does not start upwards - don't stop progression blue bar that goes round and round.  I can boot into safe mode and safe mode with networking mode.

  Hello

  As you are able to boot to the desktop in Mode safe, it means that the third-party application prevents the computer from starting in normal mode. To check you can configure the computer to clean start State and then try to boot into normal mode and check what is happening. To set up its own start-up follow the link below.

  http://support.Microsoft.com/kb/310353

  If the problem does not continues when the computer is in the clean start State follow the steps listed to identify which application is causing the problem.

  Note: When you are finished troubleshooting, follow step 7 article to start on normal startup.

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How can I get my laptop out of safe mode and back 2 normal?

  How can I get my computer out of safe mode

  It is what is on the link below in REVERSE order.
  The link is on the way to get into Safe Mode; but the instructions I give you is out!

  http://www.bleepingcomputer.com/tutorials/tutorial61.html

  Go to the above link >summary > Vista

  Start Vista normally
  Uncheck the boot under the STARTUP tab

  Using the method of System Configuration tool:

  Note: If you have problems to enter Safe Mode using the F8 method, don't use this method to force so that it starts in mode safe. For reasons that why you should read this.

  1. Close all running programs and open the windows if you are back on the desktop.
  2. Click on start () button.
  3. In the search box of the Start Menu () type msconfig and press enter on your keyboard.
  4. The System Configuration utility will open and you will see a screen similar to the one below.

     
     Figure 8. Vista System Configuration utility

     Click the Startup tab.

  5. You will now be on the screen start as shown below options.

     
     Figure 9. Tab of Vista startup in the System Configuration utility

     Uncheck the box secure boot

  6. Press apply and then press the OK button.
  7. Now, you will see a prompt stating that you must restart the computer to apply the change.

     
     Figure 10. Reboot prompt

     Click Restart to restart your computer.

  See you soon.

  Mick Murphy - Microsoft partner

• How can I get my computor out of safe mode and go back to my normal mode?

  How can I get my computor out of safe mode and go back to my regular walk mode?

  Hello

  Are there any error messages when you try to start?

  Start - type in the search box-> find MSCONFIG in top - right click - RUN AS ADMIN

  Startup tab - uncheck secure boot

  If you can not always start in normal mode, try Startup Repair

  This tells you how to access the System Recovery Options or a Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• How can I cancel your subscription to Adobe? Because it does not work with me on the computer is

  • How can I cancel your subscription to Adobe? Because it does not work with me on the computer is
  • 
    

  Cancel see answer #1 in https://forums.adobe.com/thread/2023066 - includes a link to Chat from Monday to Friday

• How can I download my photoshop on my new computer that does not have a hard drive

  How can I download my photoshop on my new computer that does not have a hard drive

  Hello

  What version of Photoshop?

  You can choose and download earlier versions of CC here: other downloads

  Concerning

  Jitendra

• How can I load my CS5 on my new laptop that does not have a hard drive?

  How can I load my CS5 on my new laptop that does not have a hard drive?

  Downloads available:

  • Suites and programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4 | CS3
  • Acrobat: XI, X | 9,8 | 9 standard
  • First Elements: 13 | 12 | 11, 10 | 9, 8, 7
  • Photoshop Elements: 13 | 12 | 11, 10 | 9,8,7
  • Lightroom: 5.7.1. 5 | 4 | 3
  • Captivate: 8 | 7 | 6 | 5
  • Contribute: CS5 | CS4, CS3

  Download and installation help links Adobe

  Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

• Problems with windows update, run sfc/scannow and boot into safe mode. (Vista Home Premium)

  Hi all

  Please bear with me here that I try to explain all the questions I have with my computer right now. I'll try to explain everything that self-organization as possible, but if you need more information or file papers to provide a solution more precise, do it me know.

  To start, I use a HP Pavilion dv6000 series (dv6748us to be exact) with Windows Vista Home Premium (32 bit) installed. (Service pack 2). About 6 months ago I got this laptop from what I believe was the conflicker virus (kept forwarding pages, arrested updates and antivirus programs, etc.) and I managed to get Windows Update works again. My help and Support did not work well, it only worked in Mode without failure, so I did some research and tried a bunch of suggested corrections (update the registry, etc.) and got it work yet once again. I don't know if one of the tools that I used all by setting the Help & Support could have caused problems that I now (as I literally tried everything under the Sun until I got to work), but my Windows Update does not work properly again.

  A few weeks ago, I installed some updates and restarted the computer, but updates did not finish install on reboot. He said the usual "Configuring Updates, do not turn off your computer", but never showed percentage complete or whatever it is. It restarted, and when I open Windows Update, he said the last time I checked the updates has never been (obviously not true), and when I tried to check the updates, it jumped right to the message telling me I have to restart my computer to complete the installation of updates. She continues to do everytime I open Windows Update. From time to time, I try to restart it, just to see if it will work, and he never does.

  I spent hours trying all the solutions I could find in Google. I tried to run system update readiness tool, which seemed to run correctly (but does not solve the problem). I then tried the difficulty it for Windows Update, and it does not solve the problem. (It might be important for me to mention that I also have problems with the difficulty It Center itself, too. Individual tools like that for Windows Update is running, but the difficulty It Center program keeps giving me the error message that "a problem is preventing the troubleshooting tool to start.") I also tried to rename the pending.xml file, and then later I deleted it, after reading in another forum that you rename the file could cause system instabillity or something like that.

  Unfortunately, I can't use system restore to solve all my problems, because all my previous restore points have disappeared (I don't know if the virus wiped out them, or if the computer removed on its own) but restore points only I checked are those that have been created recently, during the time I had these problems.

  I tried running sfc/scannow nothing helped, as he continues to tell me that there is a pending repair, but repair pending never ends. I tried to use the command of /revertpendingactions of dism.exe/image:C\/cleanup-image in the command prompt of recovery center to stop it pending repairs, and that has not worked because it claims that dism.exe that does not exist / is not a valid command. No matter what I try, I can't have this pending repair or my updates to complete pending.

  I tried to boot mode safe several times as well and he hung up on crcdisk.sys when starting every time.

  Being that I can't use sfc/scannow, System Restore, or get into Safe Mode, I'm really lost as to what I should do next. I'm honestly not sure if the problems are related, but I just thought it would make sense to list them all in one place.

  Please note that I don't want to re - install Windows Vista, or don't I think I need, because the computer works very well for most. (I use it for typing this right now). I had much rather bring all the features on mine, which I believe can be achieved with the help of the right person.

  If someone could provide me with suggestions/solutions, it would be greatly appreciated! Certainly, it would relieve a lot of stress for me!

  DISM is a thing of Windows 7. First test the hardware.

  Standard hardware troubleshooting
   
   
  First to test we can the material. Material defects can appear as many software defects, that's why we need to test the material first...

   

  Follow these steps in order. Defects of memory can cause disk corruption, disk failures can cause corruption of the disk. Damaged disc causes corrupted files (which SFC may be able to fix). If you get a stop error and after return. Do not run chkdsk with faulty memory.

   
  Diagnosis of memory

  If you have not run a diagnosis of memory, please do. Click on Start - Control Panel - choose Classic view in the left pane - choose Administrative Tools - then memory diagnostic tool.

   

  S.M.A.R.T
  Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type (or copy and paste by clicking in the command prompt window and choose Paste).
   
  Disk in Windows drives monitor for impending failure. The function is called S.M.A.R.T. It detects an imminent failure, 30% of the time. In a type elevated command prompt (it's a single line)
   
  WMIC PATH MSStorageDriver_FailurePredictStatus /namespace:\\root\wmi get active, predictfailure, reason List

   

  If it is on will be true, otherwise on enable in the BIOS of the computer.

   

  Predict the failure must be False if everything is ok.

   

  In Vista and later if SMART failure predicted Windows prompts the user to run the backup.
   
  Run chkdsk

  In computer all your drives right click and choose Properties, then the Tools tab, and then click check now. Check the TWO boxes and then start. Reset. This will take from one day to the next.

   

  SFC

  Check the alteration of the file by clicking on Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type (or copy and paste by clicking in the command prompt window and choose Paste).

   

  sfc/scannow

   

  Heat

  Heat can lead to problems of this kind, and sudden restarts without crashing. Make sure that your fans are not clogged with dust.

   

  For memory diagnostic results

  Click on Start - Control Panel (and select Classic view in the left pane), select Administrative Tools and then Event Viewer , and then look in the event (Local) - Applications and Services - Microsoft - Windows - MemoryDiagnostic-results Viewer entered.

   

  Look for EventID is 1201 or 1101 and Source is MemoryDiagnostic-results

   

  Double-click the entry for more details on this entry.

  For results of Chkdsk

  Click on Start - Control Panel (and select Classic view in the left pane) choose Administrative Tools and then Event Viewer , and then look at the Application and the System will connect (under Windows logs) for entries.

   

  Look for EventID is 7 and Source disk
  Look for EventID is 11 and the Source disk
  Look for EventID is 50 , and the Source is disk
  Look for EventID is 51 and Source disk
  
  Look for EventID is 52 and Source disk
  Look for EventID 55 and Source is NTFS
  Look for EventID is 130 and Source is NTFS
  Look for EventID is 134 and Source is NTFS
  Look for EventID is 137 and Source is NTFS
  Look for EventID 1001 and Source is Autochk
  Look for EventID 1001 and Source is Winlogon
  Look for EventID 1001 and Source is WinInit
  Look for EventID 1001 and Source is Chkdsk
  Look for EventID is 26212 and Source is Chkdsk
  Look for EventID 26213 and Source is Chkdsk
  Look for EventID 26214 and Source is Chkdsk
  Double-click the entry for more details on this entry.
   
  PS 7 and 55 are auto repair codes where windows repair disk errors silently on the fly. 52 is the SMART warning.
   
  For the results of the SFC
  Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type (or copy and paste by clicking in the command prompt window and choose Paste).
   

  findstr/c: "[SR] cannot" %windir%\logs\cbs\cbs.log|more "

   

  It will be able to see which files are corrupted.

   

  To see if there

   

  findstr/c: "[SR] repair" %windir%\logs\cbs\cbs.log|more

   

  There are often false positives for small text files that Windows uses like settings.ini and desktop.ini. Ignore these.

• How can I stop iMovie 10.1.1 from my clips big screen media cultures when I move them to the component of the project (window)?

  I am currently creating a short reel demo/culmination of a feature-length independent full length on my iMac.  The format of independent film is on the big screen and it appears this way in the media window/pane.  But when I take leave of this wide screen support and move clips / add them to the window/pane project and strengthen so the demo highlights reel, clips no longer appear on the big screen - looks like the clips (proportions?) have been cut.

  How can I stop this from happening?

  Thank you!

  If you set 'Placement of Photo' in iMovie preferences to 'Fit' rather than 'Fill' (which I think may be the default) then all your video content will be visible, but you will have bars on it and if the aspect ratio is wider than 16:9.

  

  For clips already in a timeline, you can change the setting to 'Fit' with the crop tool:

  

  Geoff.

• How can you do a system restore from safe mode

  I can't restore my computer to a previous restore point. I get security failure options when I do. I also shutd off power the computer to get out.

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

   

  Problems with system restore:

  http://Service1.Symantec.com/support/sharedtech.nsf/pfdocs/2005113009323013

  1. If you use Norton (Etc), disable it before using System Restore. info at the link above.

  2. try SR in safe mode:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  3 Malware will stop at the system restore:

  If necessary, do all the work Safe Mode with network.

   

  To get into Safe Mode with network, press F8 at the Power On / boot and use key arrow upward to get into SafeMode with networking from the list of options, and then press ENTER.

  http://www.Malwarebytes.org/MBAM.php

  Malwarebytes is as its name suggests, a Malware Remover!

  Download the free Version from the link above.

  Download, install, upgrade and scan once a fortnight.

  See you soon.

  Mick Murphy - Microsoft partner

• My Firefox exit and gives a "not responding" message once I used Google Mail. I tried to boot into "safe" mode and the problem persists.

  I have a question where Firefox wont ' quit and give a message "not responding" after I've been using Google Mail. It works fine when I'm not using this program. I tried Safe Mode and the problem still happens when I go on Google Mail, so it is not connected with modules, extensions, etc.

  Hello

  The reset Firefox feature can solve a lot of problems in restaurant Firefox to its factory default condition while saving your vital information.
  
  Note: This will make you lose all the Extensions and preferences.

  • Sites Web open is not recorded in less than 25 versions of Firefox.

  To reset Firefox, perform the following steps:

  1. Go to Firefox > help > troubleshooting information.
  2. Click on the button 'Reset Firefox'.
  3. Firefox will close and reset. After Firefox is finished, it will display a window with the imported information. Click Finish.
  4. Firefox opens with all the default settings applied.

  Information can be found in the article Firefox Refresh - reset the settings and Add-ons .

  This solve your problems? Please report to us!

  Thank you.

• Windows asks me a password and I never put a. I also try to boot into safe MODE and administrator request a password as well. How can I work around this connect? __

  can not connect to windows

  If you have forgotten your password, if you have another user who has administrative privileges account you can log in to that account and change the password of your account of origin of the user accounts applet in Control Panel. If you do not have another account like this set upwards or that you do not have the password which you will need to log on to the built-in Administrator account. In XP Home, start the computer in Mode safe. This, by repeatedly pressing the F8 key as the computer starts. This will put you in the right menu. Navigate using your arrow up; the mouse does not work here. Once in safe mode, you will see the normally hidden administrator account. The default password is white.

  In XP Pro, you don't need to go to Safe Mode. In the home screen, do Ctrl-Alt-Del twice to get the classic Windows logon box. Type in "Administrator" and the password that you assigned when you set up Windows.

  If you reset the password of the account administrator integrated into house or have Pro and don't remember the password, use NTpasswd to change the password of the built-in to a white administrator account. Download the bootable CD .iso image file, burn with third-party burning software such as free ImgBurn , Nero or Roxio. Burn as an image, not in the form of data. Start with the media that you have created. You need to maybe change the boot order in the BIOS or obtain a menu of boot command temporary with the pressure of a special key. NTpasswd will run. Follow the instructions carefully.

  http://home.eunet.no/pnordahl/ntpasswd/
  Then, go to the user accounts applet in Control Panel and set passwords that you remember and other changes. WRITE THE PASSWORDS DOWN AND PUT THEM SOMEWHERE YOU WON'T LOSE THEM.
  MS - MVP - Elephant Boy computers - don't panic!

• Why I can boot into safe mode with internet connection, use the operating system, etc., but can not open a normal session without password administrator; who got the disabled.

  OEM Vista Home Premium. Normal startup does not recognize the password. When you click User icon it says: "your account has been disabled. Please, see your system administrator"I looked in the mirror, but it did not help. Booted, press F8, went in safe mode with network connection. Everything seemed to be there. Surf the internet and then started to ask me why I don't have a password here when I did normal start-up. What is the password? Check "Microsoft Answers", but what I came out which was, I need to reinstall the OS, which I can't do it without a drive anyway.  I thought that I've used it before, I knew the password. This computer has been recently "reinstalled" internal folder 'restore '. Something must happen. A unknown password can be removed from safe mode? Ultimately how reinstall you a clean Vista when all you have is the key to product and no local or OEM support? What would be the difference between a password reset disk and the OS disk.  The two would probably be stored side by side. Not to mention that most of us Dummies want to just surf to buy, and if we can not surf, we cannot buy. Dummies help us get back on the internet, Microsoft. At least take care of this shot.

  Hi PAM,.

  In Safe Mode, try to activate the high administrator account http://www.howtogeek.com/howto/windows-vista/enable-the-hidden-administrator-account-on-windows-vista/.  Then log in using account and use it to solve problems with your normal administrator account login via control panel / user accounts / manage other accounts.  Find the one you want and make the appropriate changes to fix it.  If you can't, then you need to address as a corrupt account by using the following procedure:

  To fix this use http://windows.microsoft.com/en-AU/windows-vista/Fix-a-corrupted-user-profile.  If this is the only available administrator profile (you must be an administrator to solve this problem), activate the hidden administrator account (HAA) (i.e. what you did above, or you can do this by using these instructions instead: http://www.computerworld.com/s/article/9001970/How_to_access_the_true_Administrator_account_in_Windows_Vista?taxonomyId=17&pageNumber=1.)

  Once that is done, don't forget to disable the HAA to save it in case it is necessary once again and for safety reasons (since people often try to hack into systems using this account).  Do NOT use the HAA as your administrator account because if you lose the only administrator on the system account or it is damaged again, then you're watered.

  The fact that it says it is disabled gives me to think that you can use the guest or built-in Administrator account already (as normally, you cannot disable an account, but you can with these two which cannot be deleted and only disabled).

  The password reset disk is only good if created before that you need and only to restore a password, do not to activate a disabled account.  Another thing that goes beyond passwords here.

  A recovery disk allows you to do some advanced options of recovery by booting the disk, but it will help you restore the operating system (or help you with this problem either).

  An Installation of Vista genuinve disc (the operating system drive as you seem to be describing) is a disk that contains the operating system.  That, if it is the original disc supplied with the system and is exactly the same as the product OEM key that you must allow you to do a clean OS install (although I would be first backup you'll pretty much lost everything in the process).  The following should help: http://www.vistax64.com/tutorials/117366-clean-install-full-version-vista.html.

  If you have a factory Conditions or a recovery Partition restore disk, then these are alternatives to a clean install if you don't have this disc.  But the procedure varies according to the manufacturer, make and model of PC.  Most of the manufacturers will allow you to buy these records of restoration (for a fee) If you cannot do it with a recovery Partition cannot create diskettes from the recovery Partition or have no other option.  Visit the support site of the computer for information on this topic, available options, and related costs.

  If you cannot enable the built-in Administrator account and cannot access the system in normal mode with this or another administrator account, then I'm afraid a clean install or restore to factory conditions is your only option.

  I hope this helps.

  Good luck!

• When I started my computer this morning, it ran chkdsk at startup, windows startup it goes immediately to chkdsk, it will be repeated again and again. I can boot into safe mode, but if I try to start windows normally it runs chkdsk and does not start

  Windows does not start normally, just run chkdsk again and again

  First test the hard drive to make sure it's healthy. Test the hard drive with a diagnostic utility downloaded from site of the disc mftr. or use SeaTools for BACK of Seagate. You create a bootable CD with the files you download. You will need a third party burning software to do as the free ImgBurn, Nero or Roxio. Burn as an image, not in the form of data.

  http://www.ImgBurn.com

  http://www.Seagate.com/www/en-us/support/downloads/SeaTools/seatooldreg
  http://Seagate.custkb.com/Seagate/CRM/selfservice/search.jsp?docid=201271 (how-to)

  Boot with the CD that you have done and do a full test of the reader. The physical tests fail, replace it.

  If the hard drive then passes the physical tests, safe mode:
  Start > run > cmd [Enter]
  fsutil dirty query c: (or the appropriate drive letter) [Enter]

  This will tell you if the disc is dirty or not. Then always in cmd:

  chkntfs /x c: (or the appropriate drive letter) [Enter]

  This tells Windows not not to check this drive at startup. Reboot and it should go on the desktop. Once Windows loaded, run cmd and:

  Chkdsk /f /r c: (or the appropriate drive letter) [Enter]

  CHKDSK will run through all 5 steps. After that it's over, always in cmd:

  fsutil dirty query c: (or the appropriate drive letter) [Enter]

  to see that the dirty bit is not set on this drive.
  MS - MVP - Elephant Boy computers - don't panic!