How TFF accelorometer myRIO readings?

Similar Questions

• How can I find speed of the ram in my computer?

  I just got my HP dv6 6117dx laptop today

  I love this laptop. One thing I love, it's that it has 4 GB memory DDR3. Another thing I like is that I can pass it to a huge 16 GB.

  However, if I want to improve, how can I find the maximum speed of DDR3 RAM which can support my computer? (i.e. 1333 MHz, 1066 MHz) I'm not sure of how to interpret the readings that CPU - Z gives me; help on this or alternatives to know?

  

  Hello

  You can use CPU - Z to check. How very fast go to www.crucial.com and enter the info from your machine, it will appear the results for you. You can buy RAM from there or use the info to buy elsewhere.

  Kind regards.

• faster identified measurement of AC voltage with hp34401a

  Hello

  I use the hp33120a to generate the signal sine with frequencysweep record und AC voltage measured with hp34401a. This measure however I consider taking unusually long for what it is(approx_3_seconds_per_measurement).here I have my postal code, if someone can give me some ideas how speed up these readings that would be appreciated.

  I have

  Thank you

  Note: Labview 2009 SP1

  You don't have to be reset and the resources of your VISA for every measurement of closing.  You initialize the equipment once before the main loop, close them once after the main loop and do your reading inside the loop.  This will reduce a large number of air communications that you do not want.

• PDM with timestamp and different design tab

  Hi all

  I would like to ask how I can get readings from two sensors of tension and save them in the .tdms format. However, these readings will be continuous and long, I need a file .tdms for daily management purposes. I would like once again to management purposes were reading for each hour of the day in separate tabs.

  In addition, if convenient, I would date/time next to each reading (total three columns - 1. 2 time.) 1 sensor # 3. Probe No. 3).

  I know that partial solutions to this problem are everywhere, but I'm not as competent in LabVIEW to gather this information. If you could help me I would be very happy!

  Thanks in advance!

  Different "tabs" in a TDMS files are for different groups (I assume you are using the Excel TDM plugin).  So all of the hours you need start writing to a different group.

  In order to obtain a data column for time, just write data in time as well as your other data.  I do not remember if you can write a value of timestamp for a channel, but at the very least, you can write a double for seconds.

  However, I would recommend writing waveforms or a time value and dt beginning as properties of each channel or group.  Time data can be calculated easily later and would really just be wasting space in your file.

• Where to change the test limit

  A Council, we test a 17 subseqs in its sequence file. In one of these 17, two statements to check must have different limits for a different version of the Board of Directors. For now, the limits are hard coded numbers on the tab limits for the two statements to check. Is there some standard idioms or basic rules to know how to make the readings like this flexible?

  Thank you

  JVH

  Flexible how do you what it? If you don't mind the sequence to deal with new publishing models, you can the limits by writing them in local variables with a couple of precconditions. There is the shipper of the property and you can read the limits using them. This is the approach that I'll eventually take--whenever we can get everyone to agree on the design of database.

• GPIB instrument control

  Hi all

  I am new to this community of Labview and the use of this software.  I recently learned how to take the readings of an instrument of Keithley 2400 using their device drivers.  However, I am a bit lost when it comes to actually control the instrument.  Essentially, I want to be able to control the power supply so that it remains in a specified range, depending on the application.  I was wondering what is the process to do this... do I need to look at the manual of the device and use the Keithley commands to read and write?  I would be recognizing any input, regardless of the size.  Enjoy your time.  Thank you.

  There are functions in the pilot of NOR who control the voltage of the source. Glance to set up the output. There are several examples to settle as well. Open the example finder and navigate to output material & > instrument Drivers > labVIEW Plug-and-Play. The Instrument Driver Network has links on what a driver is and how to use a.

• How to set an application built using the C API for myRIO 3.0 to run when starting on a myRIO-1900

  It is even possible to define such an application to run at startup? If so how would you do it?

  I've compiled a program using the API and eclipse distribution OR and can run Eclipse or by running while SSH in the myRIO. Is the only document I could find about this one: http://digital.ni.com/public.nsf/websearch/B37FA04A1CB84B6C862571A30060EF03?opendocument&Submitted&&...

  The link is a little outdated, so I'm not sure of the relevance, it is today. I changed the lines of lvrt.conf to:

  RTTarget.ApplicationPath=/c/ni-rt/startup/startup.rtexe
  RTTarget.LaunchAppAtBoot = True

  None of the settings seem to do anything. I also tried to run the program as a script using rc.local which does not seem to be used in the same way as it is in Ubuntu. My compiled pogram does not include the .rtexe extension although I can add it later that might not be the same.

  I made sure that startup programs 'disable' has been disabled on the Server Web myRIO.

  Thank you

  Just in case someone has a similar question:

  https://decibel.NI.com/content/message/144527#144527

• How to play a sound stored in myRIO

  Hello

  How could I call a file saved in the usr/local/sbin in myRIO and send it to play? Thank you...

  I made this way. I turned the sound sample in a table (sound sample) and in another VI, I read this sample (creator of the ring). It works very well.

• How to install Adaptive Filter Toolkit on myRIO 1900 RT target

  Hello
  I'm working on the project of Active noise cancellation. I need to collect audio sampling rate of two microphones @40 k and 100 samples per image and audio through speakers @40 sampling rate k of output. For this, I use myRIO 1900 in FPGA high flow personality.
  When I'm designing the circuit Adatptive Filter Toolkit pallets are available in block VI, but when I'm trying to compile the circuit I get the error message saying that
  "LabVIEW: unable to load the shared library AdaptiveFilters n ensure that the library is present on the target of RT." "Either MAX allows you to install software of OR or FTP to transfer custom RT target libraries.

  I went to MAX OR to install the Adaptive Filter Toolkit, NI MAX--> network environment--> myRIO 1900--> software--> software add-on

  I can't find Adaptive Filter Toolkit or the Digital Filter Design Toolkit.

  I seriously doubt the possibility of using Adaptive Filter Toolkit in the FPGA target, but if I create the FPGA VI by default 'personality', Adaptive Filter Toolkit available palettes only not, but if I'm working on the FPGA VI high flow personality, then the pallets Adpative filter Toolkit are available but I can not compile...

  So, my question is how to install Adatptive Filter Toolkit on myRIO 1900 RT target?

  Is it possible to make custom FTP libraries RT target. I can find the Adaptive Filter library but I don't know which folder should transfer (I tried with several files that I can find but its does not work)?

  Please help me

  Thank you

  If your MAX Configuration looks good.

  After this process: NEITHER myRIO 1900--> software--> software add-on

  choose user Defined Installation you should get the view like the Picuture I added before.

  In find it examples explore, you should be able to get see--> toolkits and Modules--> adaptive filters

  Have you already tried to reinstall the Toolkit Digital Filter?

• How to run code and to communicate between the computer and myRIO?

  Hello

  I am trying to create a colortracker using the myRIO. The system is pan tilt servo with a webcam. The project works well and is able to follow and move with the desired color. However, in order to continue the project, I want to ensure the system with another device for the perception of depth and want to use the host computer for webcam and image processing and the myrio to get signals for the servos. The idea is to connect two webcams directly to the computer usb ports and keep the myRIO connected to everything does time i.e. no wifi. Can anyone guide me as to how I would go about sending signals constantly between the computer host and myRIO?

  I advise to use Variables shared Network-Published or network stream.

  You can read about them both in the cRIO guide Developer: http://www.ni.com/pdf/products/us/fullcriodevguide.pdf

  There are also examples for both in the Finder for example LabVIEW.

• How to measure the width of pulse with MyRIO

  Hello

  Sorry in advance if this is not the most appropriate forum.  I'm not entirely sure if it's a more general problem of 'software' or the MyRIO-specific.  I have searched the forums and found a few related topics but could find no one who help me in this context.

  I'm trying to measure the width of a sensor pulse ultrasonic ping.  It emits a signal conditioning - the time that it is high directly corelates how far is the object.  Being new to LabVIEW I am confused as to how do I calculate the time it remains high.

  I read that LabVIEW should not need to 'variables' as in python or C, for what is the best way to measure time, the signal is high?  Normally, I'd go (new_time - old_time), but obviously I can't store an old time in LabVIEW as I would in python or C.

  Other notes:

  I have the sensor correctly ping echoing and I can see the blips on a chart and see a perfectly square wave valid.

  

  To answer your question on how you would in LabVIEW...

  While LabVIEW has not stated/named variables that you have in a language based on text, the data is stored on the wires. You can use the nodes as node registers or shift of feedback to store values between iterations of a loop:

  (this will keep subtracting y (starting with 0) and store the result for the next time it runs)

  LabVIEW also has functions in the range of mathematics/signal processing to make the detection of pulse on a waveform.

• How to install the biomedical toolkit to myRIO 1900 RT target

  Hello

  I try to install biomedical toolkit to myRIO using NI MAX. However, after that I installed on my system and ran the software Assistant in real-time to myRIO, I couldn't find the box tool as shown in the pictures

  

  I tried quitting biomedical screws on the portion of your code RT, but it complicates things even more by creating conflicts between the PC and the copy of LabVIEW RT library. Is there another way, I can understand that?

  

  You should not have to install the toolkit separately to the myRIO, it should be included automatically. However, if you have not done so already you need to reinstall the software recommended defined to ensure that these screws are pushed towards the target. After you do this verification for the biomedical palette on your myRIO.

  In addition, some express screws included in this palette will not work on this target because they use DAQmx, which is not compatible with our RIO devices. You will still be able to run the 'Biosignal Measurements' screw, but you will need to acquire the data using standard RIO methods.

• How to replace the factory supplied FPGA functionality in myRIO?

  Hello

  I have created an example of FPGA code and downloaded in myRIO.  I expect he would have erased the FPGA factory feature shipped which included all the interpretation of the digital (DIO) of input/output PWM asynchronous universal receivers/transmitters (UART), inputs of encoder, I2C and SPI.  Is it possible to put this factory shipped to FPGA code?  Where can I get this code?

  Thank you

  Ajay.

  Hello Ajay,

  When you run your host code, which calls the FPGA VI (opens its reference), it automatically deploys the FPGA code to the material. If you run after code samples, to come with drivers myRIO, it will deploy default FPGA code included.

  To find the FPGA defalt code, which comes with the drivers, create a new project to create a project of-> models-> myRIO and select myRIO custom FPGA project, you will find a FPGA Default.vi of hand inside.

  It is sufficient to note that functiality UART is not implemented on the FPGA, but instead uses a feature included in the architecting processor. If you still have the UART functionality, even with your custom running FPGA code.

  Thank you

  AREV

  

• How to implement toolkit blurred on the myRio?

  Hello

  We are trying to implement the logic fuzzy toolkit on Myrio. but are not successes. one has experience to implement the control of fuzzy logic on MyRio?
  I tried on PC, it works fine but when I tried on MyRio, it's not that I was expecting.

  can someone help me solve this problem?

  Thank you

  the error may display set

  The best

  Santo

  Hi Santo,

  have you checked the path to the file you want to load when you start your VI?

  Err7 means generally: "file not found!"

  Have you copied the file from your PC to the myRIO? The myRIO can't access hard disk of your PC!

• How can I convert 9213 readings of TC in temperatures on FPGA?

  I use a cRIO-9076 with 9213 module to capture readings from thermocouples (type K).  Is it possible to convert these readings (voltage of the FXP Data reading) in the temperature on the FPGA values?  My goal is then to use these temperatures to control an analog output through a PID.

  According to the specifications, the 9213 should be able to read 8 TC to 100 Hz.  I would like to be able to run as fast PID TC can be read accurately.

  I couldn't find an example of code that does the conversion of temperature-voltage on the FPGA.  The example of getting started is send you the values of voltage of TC to the processor, RT, then converts the tensions in temperatures.  I was not able to get that to run faster that about 50 Hz in one analysis comparative VI.  Once I have add any other code to the RT target, I think I'll have to run a lot slower than 50 Hz.

  Any suggestions / examples / whitepapers can you tell me?

  Thank you

  John

  Hi John,.

  Take a look at the Started.lvpoj get 9211 from the Finder of the example. You can use the same screw of this project to convert volts to your 9213 module temperature. In order to preserve the accuracy of the readings, it is recommended to convert the voltage to temperature in your host VI. The rate of your control loop is not very fast, only so you should be able to run your PID loop and to convert your data to the frequency of 100 Hz to your host VI.