How the market for MS network administrators?

Similar Questions

• I don't remember the password for my network, but I do remember the password for my computer and my home group.

  I don't remember the password for my network, I remember the password to my computer and my home group, they are all different to change that, but family crisis distract me unable to use my ipad now or my other computer help!

  original title: password

  Hello

  What operating system is installed on the computer?

  Perform the steps mentioned below, if you have Windows 7 installed on the computer and see if the problem persists.

  a: right click on the wireless in your taskbar icon.

  b: open network and sharing Center and then click manage wireless networks on the left.

  c: you will see all the networks you have connected too.

  d: right click on any connection to Properties.

  e: click on the Security tab that shows the details of the security of the network including the password. Click on the box to Show characters.

  Hope this information helps.

• Satellite L510 - how to install the driver for wireless network card?

  Hello

  I recently bought Toshiba Satellite L510 laptop and problem in the installation of the wireless driver. I downloaded the driver from Toshiba sites.
  And installation get competed with success but it always ask for divers 'Network controller' and 'Askey for Toshiba.
  I'm trying different drivers of these last two days, but without success.

  Can someone Guild me please how to configure computer L510 laptop wireless. Also where can I get the drivers mentioned above.

  Thanks in advance.

  Hi mate,

  I m asking you to install the WLAN driver on your laptop computer purchased recently. Normally all the stuff is already preinstalled the operating system with all the drivers and tools. He s ready to use.

  However, what you mean exactly with her always ask for divers to Askey Toshiba network controller?

  Your wireless network card is listed in the Manager device correctly or yellow exclamation? What WLAN card you have?

• Wireless network is displayed with a cross and will not let me connect saying the settings for this network do not match the requirements of the networs and it is a hidden network how to make it visible again?

  hardware device

  my wireless network is displayed with a cross and will not let me connect saying settings for this network do not match the requirements of the networs and it is a hidden network how to make it visible again :(

  Hello

  What operating system installed on the computer?

  Note: Look for errors in the network card device manager.

  Method 1: Follow the article mentioned below, if you are using Windows 7 operating system.

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2:

  He looks at the IP address and other parameters are not set correctly, I suggest you contact your Internet service provider or provider router wireless to help on this.

  For more information, follow the below mentioned article:

  Set up a wireless router:

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

  Follow the below mentioned articles and see if they help you:

  Set up a wireless network:

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  Wi - Fi and in Windows network connection issues:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Wireless network card: frequently asked questions:

  http://Windows.Microsoft.com/en-us/Windows7/wireless-networking-frequently-asked-questions

• I have trouble understanding how the calendar for the vi simulate Signal Express. Can anyone help?

  I'm generating a signal to 100,000 samples per second. The frequency is 4 Hz. I then pass the signal through the basic vi trigger detection to find out where the wave crosses 0.5.

  Since the signal is 4 Hz, the waveform should cross 0.5 each 0.25 sec. However, when I created a table of the times that the trigger is activated, it is not 0.25 seconds.

  I don't know if there is a problem with my calculation of the duration of simulation, or if I don't understand how the vi signal simulation works. Thank you very much for your ideas!

  Yes, you made a few mistakes or bad assumptions about who express vi.

  The frequency is 4 Hz samples per second is of 100,000 samples (orders of magnatude) generated too high are 76 (0.76mSecs worth of data).  1% duty cycle so a transition product only once every thousand loops! 1315 or 1316 loops between L - H transition to be more precise

  Try

  40 s/s

  40Samples (a seconds of data)

  right to 50%

• I can't find the driver for my network on 431 Hp windows 7 32-bit controller

  Hello, I have a problem here. IM using 431 HP with windows 7 32 bit. I can't find the right driver for my network controller. Here's my hardware ID:

  PCI\VEN_168C & DEV_002B & SUBSYS_1461103C & REV_01
  PCI\VEN_168C & DEV_002B & SUBSYS_1461103C
  PCI\VEN_168C & DEV_002B & CC_028000
  PCI\VEN_168C & DEV_002B & CC_0280

  I try so many driver for wifi but none of them works. my wifi can not always be used, and it says that it cannot find a driver.

  Here is the status of the device:

  The drivers for this device are not installed. (Code 28)

  There is no driver selected for the item or a set of device information.

  To find a driver for this device, click Update driver.

  Please can someone help me? Many thanks for you guys

  Hello:

  Here is the link for the driver you need for the Atheros wireless card in your notebook.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5060880&swItem=ob-108905-1&prodNameId=5060882&swEnvOID=4052&swLang=13&taskId=135&mode=3

• Cannot change the passphrases for wireless network after upgrade

  Hello

  I just upgraded the firmware for my R7000 and after that (I think) it not possible to change key phrases for the parameters without wire and I cannot see what that the security is WEP WPA etc.

  A few ideas...?

  Best regards Thomas

  Reset the default router and reconfigure from scratch.

• Satellite L100-120: can not find the driver for wireless network card

  Hello world! help me cause I don't know who I can apply my probem for! I bought this laptop in Russia - and not a bad model, but I want to change the operating system in the way that I love - so I installed vista, but the note does not work well with it, then I installed Windows XP sp2 home ed, changed in the way I wanted to, but the main problem is that I had to install almost all pilots of myself-

  Toshiba modifies his notes in the way that without its own operating system video card, modem card or wifi and sound card do not work! Well, I found all the drivers except for wifi adapter - I almost tried everything but he can't help! wifi card does not work on my note!

  could someone help me in this matter?

  The laptop was supplied with the mini-PCI Intel 3945ABG card WLan. Am I wrong?
  You should look on the Intel page for Wlan drivers for the Vista operating system.
  I also found the drivers for my Intel Wlan card on the Web site.

• How to "automatically detect the proxy for this network settings" and "Use system proxy settings" work behind the scenes?

  How can I see what the firefox proxy actually uses when I check either of these two options?
  There go to Internet Explorer?
  They are stored somewhere in the registry?

  Hi conectionist,
  This is taken if there is a proxy configured in the network settings on your operating system. If you want to test there may be further on:

  • https://addons.Mozilla.org/en-us/fire.../?src=search

  Please feel free to research to find a better if necessary.

• How can I change the settings for virtual network?

  Hi all

  After updateing VMPlayer the other day that my VM access is no longer the internet, I was told that I need to restore my virtual network settings. Does anyone know how to do this? I only have the ability to change my host network, bridge, etc...

  I don't see anywhere the ability to disable automatic bypass in editor of virtual network, suggestions? Thank you

  You already have the answer: Re: WIN XP VM does not connect to Internet but ping google.com, etc... Please help

• How to use the Socket for AS3 networking?

  Hello, I'm a Flash game and have successfully obtained the RTMFP to work, but it is not very reliable and has a little loss of packages inside. I've heard many people only using TCP (socket), it is much tighter, but I have no idea on how to do it. I've Googled it many times, yet I really can't seem to find a clear answer. I hear you must have a server... How do you get one? Is it possible to make your own simple server that people your LAN can play? Thanks in advance.

  Yes, you can make your own simple server using the ServerSocket class and connect with the Socket class. And then you have TCP... it's actually pretty simple. Discover the ServerSocket docs to start, and there are also many examples if you googled around.

  http://help.Adobe.com/en_US/FlashPlatform/reference/ActionScript/3/Flash/NET/ServerSocket. HTML

• The field for local network IPs access permissions

  Is an error or a restriction of the service if I have added ' * ' to avoid restrictions on access area on my app it works only on public IP addresses and is not with local network IPs?

  (ie. my phone WiFi 192.16.1.116 and trying to access information on a pc with 192.16.1.119, result: timeout)

  If the same request is made to a public IP (pc) IE. 200.31.90.37, then it works as expected.

  NOTE:

  -This request for access is made by a webworks installed on the phone app. the answer is in JSONP format.

  -PC firewall disabled.

  Tests failed

  -Tests on wifi, access to a local IP network with the phone on and off data service

  Successful trial

  -Tests on Internet, access a public IP, same phone, same app.

  As indicated in the following link, there is no indication that this behavior is expected:

  http://docs.BlackBerry.com/en/developers/deliverables/27280/Allowing_access_to_external_resources_an...

  If anyone knows an example where "*" works for LAN IPs please let me know.

  Kind regards

  OK... sit tight for this possible explanation

  A BlackBerry has two different designs to consider:

  (1) physical network connection

  (2) selection of transport

  The physical network connection is pretty self explainatory (wifi, bluetooth, GPRS, CDMA).  The selection of Transport can better be seen as a VPN Tunnel/connection.  Such transport may be BES, BIS, direct TCP, WAP etc gateway.

  Even if you're on WiFi, you can still have your transport (VPN) connected through BIS.  This is configured through your application settings.

  The browser from on the BB6 uses special transportation (no available applications) who did essentially the equivalent of a DNS lookup and follows a logic to see how endpoint can be accessed.  It will then forward through the transport that's going to happen to its endpoint.

  So in the browser, it detects your IP address isn't public and a rebooking via the TCP/IP connection direct to go directly to your local server.

  In a BlackBerry application, you must declare your list of transport order which I will try and failover to the other if it is not reachable on the first transport.

  Stopped default transport is in an application of WebWorks BES, BIS - B, TCP_WIFI, TCP_CELLULAR, WAP2, WAP

  More information on transport in WebWorks here:

  http://docs.BlackBerry.com/en/developers/deliverables/27261/Widget_element_834671_11.jsp#RIM_connect...

  In your case, you would have to change the order of the TCP_WIFI put everything first.  WARNING: Different transport have different failover times.  B BIS and BES are instantly switched if they are not enabled with this service. TCP_WIFI will actually make a connection delay before switching.  So if you don't have a WiFi connection, it will timeout on each request for a resource before it tries then BIS - B.

  So, it boils down to what you want your app to be able to do.  If she wants to access the public IP addresses, then you want to keep the default transport order.  If you want it to be able to discover the local and public IP addresses, then you will have a little more work to do.

• I have a custom-made computer and it says that I need the driver for my network controller

  Hello!
  I have a custom office and tab device from my Office Manager, it says that my network controller is missing from the driver. I think I might have uninstalled on accident. My hardware for this device id is pci\ven_14e4 & dev_4727 & subsys_0010128 & rev_01
  Pci\ven_14e4 & dev_4727 & subsys_00101028
  Pci\ven_14e4 & dev_4727 & cc_028000
  Pci\ven_14e4_dev_4727 & cc_0280
  Please help or at least point me in the right direction. Thank you

  My advice would be to remove the adapter and know what brand is and go to the website of support to him and to find the right driver, he needs.  There should be some kind of identification tag on.

  There are literally dozens of broadcom drivers that might be, and since you said you have a custom built PC, I got hit with a driver, and unfortunately it did not work.

  It is a part not HP so it will take some manufacturers for this driver.

• Reference Dell MD3200i correct editing with IP system and the NIC for faster network speeds

  Hi all

  I worked on this project for a while now. I did a lot of research and have contacted Dell several times. I need help.

  I have 2 sets of identical to use for Hyper-V clusters servers. We bought a Dell MD3200i in November, we also bought a Dell 5424 switch and a Cisco SLM2048 switch. These servers have Real Tek 2 network cards for iSCSI Jumbo frames is 9 k

  The Dell MD3200i is two SAN controllers. Dell 5424 is the iSCSI optimized switch and Cisco is a 48 switch ports. iSCSI is on its own network that nothing else is connected to it. (There is an Iomega NAS and a promise Vtrak SAN Tech with all current domain of execution with iSCSI controller)

  Reference Dell MD3200i controller 0 Port 0 192.168.130.101 controller 1 Port 0 192.168.131.101

  Controller controller Port 1 0 192.168.130.102 1 1 192.168.131.102

  Controller controller Port 2 0 192.168.130.103 1 2 192.168.131.103

  Controller controller Port 3 0 192.168.130.103 1-3 192.168.131.104

  Cisco switch has 1 VLAN n ° 1 on it and the 130 subnet inside elements. There are 8 connections to the switch. 4 controller 0 and 1 of each of the servers. It has an IP of 192.168.132.4, but that switch IP does not make difference. Lighted Jumbo frames

  Dell switch has 2 of #1 for various things such as the domain controller, Vtrack, and SIN. Subnet 2 is 131 and has a total of 8 connectors inside. 4 in 1 controller and 1 from each of the servers. Lighted Jumbo frames. The switch IP address is 192.168.132.2

  Groups of servers. Each server node running Windows 2008 R2 SP1 and running hyper-v with virtual server clusters / storage folder on them. 2 Realtek NIC with Jumbo frames made 9 k ProdNode1 and ProdNode2 have 12 Core i7 CPU with 12 GB memory, EXNode1 and ExNode2 have 12 Core i7 CPU with 24 GB of memory.

  ProdNode1 iSCSI-1 192.168.130.110 ProdNode1 iSCSI-2 192.168.131.110

  ProdNode2 iSCSI-1 192.168.130.120 ProdNode2 iSCSI-2 192.168.131.120

  ExNode1 iSCSI-1 192.168.130.130 ExNode1 iSCSI-2 192.168.131.130

  ExNode2 iSCSI-1 192.168.130.140 ExNode2 iSCSI-2 192.168.131.140

  Portal discovery iSCSI on ProdNode1 went to 192.168.130.110 192.168.130.101 and 192.168.131.110 192.168.131.101 each of the other servers Discovery Portal have been pairs like this.

  iSCSI tab click on add 8 MPIO sessions at each of the ports on the MD3200i from Dell, target. For example, I added 1 session of 192.168.130.101 using it. Add Session,--> activate--> Advanced Mutlipath--> Local--> IP 192.168.130.110 initiator and target 192.168.131.101 iSCSI adapter. This is repeated on all servers. 4 connections for each NIC.

  The network is very slow. It revolved around 2 to 4 MB/MIN and it should be much faster. Initially, we had only the Cisco switch with only 1 VLAN and everything connected directly to it. I read somewhere that MPIO has been the problem, so I went through the same configuration but does not verify the MPIO checkbox above. Once this has been done, the network speed went up to 1.5 GB/Min but modular storage Dell was not happy, and virtual servers would fail and the connection is not very stable.

  What wrong with my setup? Can I directly home and fix the servers directly to the PowerVault and will make stable and allow for failover and redundancy NIC? I need to get this stable so I can move with something else.

  Thank you Ron

  You will need to change your system of intellectual property on this:

  rbramble

  EX-Node1 iSCSI-1 192.168.130.130

  EX-Node1 iSCSI-2 192.168.131.130

  EX-Node2 iSCSI-1 192.168.132.140

  EX-Node2 iSCSI-2 192.168.133.140

  Prod-Node1 iSCSI-1 192.168.130.10

  Prod-Node1 iSCSI-2 192.168.131.10

  Prod-Node2 iSCSI-1 192.168.132.20

  Prod-Node2 iSCSI-2 192.168.133.20

  Reference Dell MD3200i

  Controller 0 Port 0 - 192.168.130.101 Jumbo Frames 9K

  Controller 0 Port 1 - 192.168.131.101 Jumbo Frames 9K

  Controller 0 Port 2 - 192.168.132.101 Jumbo Frames 9K

  Controller 0 Port 3 - 192.168.133.101 Jumbo Frames 9K

  Controller 1 Port 0 - 192.168.130.102 Jumbo Frames 9K

  Controller Port 1 1 - 192.168.131.102 Jumbo Frames 9K

  Controller 1 Port 2 - 192.168.132.102 Jumbo Frames 9K

  Controller 1 Port 3 - 192.168.133.102 Jumbo Frames 9K

  Your iSCSI sessions will be:

  For EX-Node1:

  -192.168.130.130 to 192.168.130.101

  -192.168.130.130 to 192.168.130.102

  -192.168.131.130 to 192.168.131.101

  -192.168.131.130 to 192.168.131.102

  For EX-Node2:

  -192.168.132.140 to 192.168.132.101

  -192.168.132.140 to 192.168.132.102

  -192.168.133.140 to 192.168.133.101

  -192.168.133.140 to 192.168.133.102

  For Prod-Node1:

  -192.168.130.10 to 192.168.130.101

  -192.168.130.10 to 192.168.130.102

  -192.168.131.10 to 192.168.131.101

  -192.168.131.10 to 192.168.131.102

  For Prod-Node2:

  -192.168.132.20 to 192.168.132.101

  -192.168.132.20 to 192.168.132.102

  -192.168.133.20 to 192.168.133.101

  -192.168.133.20 to 192.168.133.102

• How the scripts for the new virtual machine storage profile

  Hey all,.

  I have a long script that I've been put together so that our operations people size new virtual machines.  I ask a series of questions for such things as the VM name, cluster, VLAN, plug hardware, OS/template, etc.  I use LucD method to create a temporary copy of a customization OS specification to insert a static IP address.  I have everything works except that I can't figure out how this script drop-down list:

  

  vSphere 5.0, any VCD.  Looks like it should be pretty simple, but I can't find anything on how to do it.  It would be nice to choose this in the New - VM cmdlet somewhere, as well as the use of the GUI.  Any ideas?

  Throw a glance PowerCLI 5.8, when it is available, there is a charge storage profile cmdlets in there (as we showed in our VMworld session this week).